2018-11-29 17:00:22 +08:00
|
|
|
menu "Hardware Drivers Config"
|
|
|
|
|
|
|
|
|
|
config SOC_STM32F103ZE
|
|
|
|
|
bool
|
|
|
|
|
select SOC_SERIES_STM32F1
|
2019-09-11 12:06:43 +08:00
|
|
|
select RT_USING_COMPONENTS_INIT
|
|
|
|
|
select RT_USING_USER_MAIN
|
2018-11-29 17:00:22 +08:00
|
|
|
default y
|
|
|
|
|
|
|
|
|
|
menu "Onboard Peripheral Drivers"
|
|
|
|
|
|
|
|
|
|
config BSP_USING_USB_TO_USART
|
|
|
|
|
bool "Enable USB TO USART (uart1)"
|
2019-01-08 12:04:44 +08:00
|
|
|
select BSP_USING_UART
|
2018-11-29 17:00:22 +08:00
|
|
|
select BSP_USING_UART1
|
|
|
|
|
default y
|
|
|
|
|
|
|
|
|
|
config BSP_USING_RS485_OR_RS232
|
|
|
|
|
bool "Enable RS485/RS232 (uart2 be shared)"
|
|
|
|
|
select BSP_USING_UART2
|
|
|
|
|
default n
|
|
|
|
|
|
|
|
|
|
config BSP_USING_SPI_FLASH
|
2019-01-28 13:55:23 +08:00
|
|
|
bool "Enable SPI FLASH (W25Q64 spi1)"
|
2019-01-08 12:04:44 +08:00
|
|
|
select BSP_USING_SPI
|
2018-11-29 17:00:22 +08:00
|
|
|
select BSP_USING_SPI1
|
|
|
|
|
select RT_USING_SFUD
|
|
|
|
|
select RT_SFUD_USING_SFDP
|
|
|
|
|
default n
|
|
|
|
|
|
2018-12-17 10:44:30 +08:00
|
|
|
config BSP_USING_RGB
|
|
|
|
|
bool "Enable RGB LED (timer3 channel2 - 4)"
|
|
|
|
|
select RT_USING_PWM
|
|
|
|
|
select BSP_USING_PWM
|
|
|
|
|
select BSP_USING_PWM3
|
|
|
|
|
select BSP_USING_PWM3_CH2
|
|
|
|
|
select BSP_USING_PWM3_CH3
|
|
|
|
|
select BSP_USING_PWM3_CH4
|
|
|
|
|
default n
|
|
|
|
|
|
2018-12-10 09:48:01 +08:00
|
|
|
config BSP_USING_POT
|
|
|
|
|
bool "Enable potentiometer"
|
|
|
|
|
select BSP_USING_ADC
|
|
|
|
|
select BSP_USING_ADC1
|
|
|
|
|
default n
|
|
|
|
|
|
2018-11-29 17:00:22 +08:00
|
|
|
config BSP_USING_EEPROM
|
|
|
|
|
bool "Enable I2C EEPROM (i2c1)"
|
|
|
|
|
select BSP_USING_I2C1
|
|
|
|
|
default n
|
|
|
|
|
|
|
|
|
|
config BSP_USING_ETH
|
|
|
|
|
bool "Enable Ethernet Driver (spi2)"
|
|
|
|
|
default n
|
|
|
|
|
select PKG_USING_WIZNET
|
|
|
|
|
select WIZNET_DEVICE_EXTERN_CONFIG
|
|
|
|
|
select BSP_USING_SPI2
|
|
|
|
|
if BSP_USING_ETH
|
|
|
|
|
if WIZNET_DEVICE_EXTERN_CONFIG
|
|
|
|
|
config WIZ_SPI_DEVICE
|
|
|
|
|
string
|
|
|
|
|
default "spi20"
|
|
|
|
|
|
|
|
|
|
config WIZ_RST_PIN
|
|
|
|
|
int
|
|
|
|
|
default 111
|
|
|
|
|
|
|
|
|
|
config WIZ_IRQ_PIN
|
|
|
|
|
int
|
|
|
|
|
default 104
|
|
|
|
|
endif
|
|
|
|
|
|
|
|
|
|
config EXTERNAL_PHY_ADDRESS
|
|
|
|
|
hex
|
|
|
|
|
default 0x00
|
|
|
|
|
|
|
|
|
|
endif
|
|
|
|
|
|
2018-12-17 10:44:30 +08:00
|
|
|
config BSP_USING_SDCARD
|
|
|
|
|
bool "Enable SDCARD (sdio)"
|
|
|
|
|
select BSP_USING_SDIO
|
|
|
|
|
select RT_USING_DFS
|
|
|
|
|
select RT_USING_DFS_ELMFAT
|
|
|
|
|
default n
|
|
|
|
|
|
2018-11-29 17:00:22 +08:00
|
|
|
endmenu
|
|
|
|
|
|
|
|
|
|
menu "On-chip Peripheral Drivers"
|
|
|
|
|
|
|
|
|
|
config BSP_USING_GPIO
|
|
|
|
|
bool "Enable GPIO"
|
|
|
|
|
select RT_USING_PIN
|
|
|
|
|
default y
|
|
|
|
|
|
2019-01-08 12:04:44 +08:00
|
|
|
menuconfig BSP_USING_UART
|
2019-01-08 14:07:46 +08:00
|
|
|
bool "Enable UART"
|
|
|
|
|
default y
|
|
|
|
|
select RT_USING_SERIAL
|
|
|
|
|
if BSP_USING_UART
|
|
|
|
|
config BSP_USING_UART1
|
|
|
|
|
bool "Enable UART1"
|
|
|
|
|
default y
|
|
|
|
|
|
|
|
|
|
config BSP_UART1_RX_USING_DMA
|
|
|
|
|
bool "Enable UART1 RX DMA"
|
|
|
|
|
depends on BSP_USING_UART1 && RT_SERIAL_USING_DMA
|
|
|
|
|
default n
|
|
|
|
|
|
|
|
|
|
config BSP_USING_UART2
|
|
|
|
|
bool "Enable UART2"
|
|
|
|
|
default n
|
|
|
|
|
|
|
|
|
|
config BSP_UART2_RX_USING_DMA
|
|
|
|
|
bool "Enable UART2 RX DMA"
|
|
|
|
|
depends on BSP_USING_UART2 && RT_SERIAL_USING_DMA
|
|
|
|
|
default n
|
|
|
|
|
|
|
|
|
|
config BSP_USING_UART3
|
|
|
|
|
bool "Enable UART3"
|
|
|
|
|
default n
|
|
|
|
|
|
|
|
|
|
config BSP_UART3_RX_USING_DMA
|
|
|
|
|
bool "Enable UART3 RX DMA"
|
|
|
|
|
depends on BSP_USING_UART3 && RT_SERIAL_USING_DMA
|
|
|
|
|
default n
|
|
|
|
|
endif
|
2019-01-08 12:04:44 +08:00
|
|
|
|
2018-12-10 09:48:01 +08:00
|
|
|
config BSP_USING_ON_CHIP_FLASH
|
|
|
|
|
bool "Enable on-chip FLASH"
|
|
|
|
|
default n
|
|
|
|
|
|
2019-01-08 12:04:44 +08:00
|
|
|
menuconfig BSP_USING_SPI
|
|
|
|
|
bool "Enable SPI BUS"
|
2018-11-29 17:00:22 +08:00
|
|
|
default n
|
|
|
|
|
select RT_USING_SPI
|
2019-01-08 12:04:44 +08:00
|
|
|
if BSP_USING_SPI
|
|
|
|
|
config BSP_USING_SPI1
|
|
|
|
|
bool "Enable SPI1 BUS"
|
|
|
|
|
default n
|
|
|
|
|
|
|
|
|
|
config BSP_SPI1_TX_USING_DMA
|
|
|
|
|
bool "Enable SPI1 TX DMA"
|
|
|
|
|
depends on BSP_USING_SPI1
|
|
|
|
|
default n
|
|
|
|
|
|
|
|
|
|
config BSP_SPI1_RX_USING_DMA
|
|
|
|
|
bool "Enable SPI1 RX DMA"
|
|
|
|
|
depends on BSP_USING_SPI1
|
|
|
|
|
select BSP_SPI1_TX_USING_DMA
|
|
|
|
|
default n
|
|
|
|
|
|
|
|
|
|
config BSP_USING_SPI2
|
|
|
|
|
bool "Enable SPI2 BUS"
|
|
|
|
|
default n
|
|
|
|
|
|
|
|
|
|
config BSP_SPI2_TX_USING_DMA
|
|
|
|
|
bool "Enable SPI2 TX DMA"
|
|
|
|
|
depends on BSP_USING_SPI2
|
|
|
|
|
default n
|
|
|
|
|
|
|
|
|
|
config BSP_SPI2_RX_USING_DMA
|
|
|
|
|
bool "Enable SPI2 RX DMA"
|
|
|
|
|
depends on BSP_USING_SPI2
|
|
|
|
|
select BSP_SPI2_TX_USING_DMA
|
|
|
|
|
default n
|
|
|
|
|
|
|
|
|
|
config BSP_USING_SPI3
|
|
|
|
|
bool "Enable SPI3 BUS"
|
|
|
|
|
default n
|
|
|
|
|
|
|
|
|
|
config BSP_SPI3_TX_USING_DMA
|
|
|
|
|
bool "Enable SPI3 TX DMA"
|
|
|
|
|
depends on BSP_USING_SPI3
|
|
|
|
|
default n
|
|
|
|
|
|
|
|
|
|
config BSP_SPI3_RX_USING_DMA
|
|
|
|
|
bool "Enable SPI3 RX DMA"
|
|
|
|
|
depends on BSP_USING_SPI3
|
|
|
|
|
select BSP_SPI3_TX_USING_DMA
|
|
|
|
|
default n
|
|
|
|
|
endif
|
2018-11-29 17:00:22 +08:00
|
|
|
|
|
|
|
|
menuconfig BSP_USING_I2C1
|
|
|
|
|
bool "Enable I2C1 BUS (software simulation)"
|
|
|
|
|
default n
|
|
|
|
|
select RT_USING_I2C
|
|
|
|
|
select RT_USING_I2C_BITOPS
|
|
|
|
|
select RT_USING_PIN
|
|
|
|
|
if BSP_USING_I2C1
|
|
|
|
|
config BSP_I2C1_SCL_PIN
|
|
|
|
|
int "i2c1 scl pin number"
|
|
|
|
|
range 0 175
|
|
|
|
|
default 22
|
|
|
|
|
config BSP_I2C1_SDA_PIN
|
|
|
|
|
int "I2C1 sda pin number"
|
|
|
|
|
range 0 175
|
|
|
|
|
default 23
|
|
|
|
|
endif
|
|
|
|
|
|
2018-12-17 10:44:30 +08:00
|
|
|
menuconfig BSP_USING_TIM
|
|
|
|
|
bool "Enable timer"
|
|
|
|
|
default n
|
|
|
|
|
select RT_USING_HWTIMER
|
|
|
|
|
if BSP_USING_TIM
|
|
|
|
|
config BSP_USING_TIM2
|
|
|
|
|
bool "Enable TIM2"
|
|
|
|
|
default n
|
|
|
|
|
|
|
|
|
|
config BSP_USING_TIM3
|
|
|
|
|
bool "Enable TIM3"
|
|
|
|
|
default n
|
|
|
|
|
|
|
|
|
|
config BSP_USING_TIM4
|
|
|
|
|
bool "Enable TIM4"
|
|
|
|
|
default n
|
|
|
|
|
|
|
|
|
|
config BSP_USING_TIM5
|
|
|
|
|
bool "Enable TIM5"
|
|
|
|
|
default n
|
|
|
|
|
endif
|
|
|
|
|
|
|
|
|
|
menuconfig BSP_USING_PWM
|
|
|
|
|
bool "Enable pwm"
|
|
|
|
|
default n
|
|
|
|
|
select RT_USING_PWM
|
|
|
|
|
if BSP_USING_PWM
|
|
|
|
|
menuconfig BSP_USING_PWM3
|
|
|
|
|
bool "Enable timer3 output pwm"
|
|
|
|
|
default n
|
|
|
|
|
if BSP_USING_PWM3
|
|
|
|
|
config BSP_USING_PWM3_CH2
|
|
|
|
|
bool "Enable PWM3 channel2"
|
|
|
|
|
default n
|
|
|
|
|
|
|
|
|
|
config BSP_USING_PWM3_CH3
|
|
|
|
|
bool "Enable PWM3 channel3"
|
|
|
|
|
default n
|
|
|
|
|
|
|
|
|
|
config BSP_USING_PWM3_CH4
|
|
|
|
|
bool "Enable PWM3 channel4"
|
|
|
|
|
default n
|
|
|
|
|
endif
|
|
|
|
|
endif
|
|
|
|
|
|
2018-12-10 09:48:01 +08:00
|
|
|
menuconfig BSP_USING_ADC
|
|
|
|
|
bool "Enable ADC"
|
|
|
|
|
default n
|
|
|
|
|
select RT_USING_ADC
|
|
|
|
|
if BSP_USING_ADC
|
|
|
|
|
config BSP_USING_ADC1
|
|
|
|
|
bool "Enable ADC1"
|
|
|
|
|
default n
|
|
|
|
|
endif
|
|
|
|
|
|
2019-03-19 18:21:51 +08:00
|
|
|
menuconfig BSP_USING_ONCHIP_RTC
|
2018-12-10 09:48:01 +08:00
|
|
|
bool "Enable RTC"
|
|
|
|
|
select RT_USING_RTC
|
|
|
|
|
default n
|
2019-03-19 18:21:51 +08:00
|
|
|
if BSP_USING_ONCHIP_RTC
|
|
|
|
|
choice
|
|
|
|
|
prompt "Select clock source"
|
|
|
|
|
default BSP_RTC_USING_LSE
|
|
|
|
|
|
|
|
|
|
config BSP_RTC_USING_LSE
|
|
|
|
|
bool "RTC USING LSE"
|
|
|
|
|
|
|
|
|
|
config BSP_RTC_USING_LSI
|
|
|
|
|
bool "RTC USING LSI"
|
|
|
|
|
endchoice
|
|
|
|
|
endif
|
2018-12-10 09:48:01 +08:00
|
|
|
|
|
|
|
|
config BSP_USING_WDT
|
|
|
|
|
bool "Enable Watchdog Timer"
|
|
|
|
|
select RT_USING_WDT
|
|
|
|
|
default n
|
|
|
|
|
|
2018-12-17 10:44:30 +08:00
|
|
|
config BSP_USING_SDIO
|
|
|
|
|
bool "Enable SDIO"
|
|
|
|
|
select RT_USING_SDIO
|
|
|
|
|
select RT_USING_DFS
|
|
|
|
|
default n
|
2019-10-31 00:01:17 +08:00
|
|
|
|
|
|
|
|
menuconfig BSP_USING_CAN
|
2019-03-13 16:20:56 +08:00
|
|
|
bool "Enable CAN"
|
2019-02-19 13:29:23 +08:00
|
|
|
default n
|
|
|
|
|
select RT_USING_CAN
|
|
|
|
|
if BSP_USING_CAN
|
|
|
|
|
config BSP_USING_CAN1
|
|
|
|
|
bool "using CAN1"
|
|
|
|
|
default n
|
|
|
|
|
endif
|
2019-10-31 00:01:17 +08:00
|
|
|
|
|
|
|
|
config BSP_USING_USBD
|
|
|
|
|
bool "Enable USB device"
|
|
|
|
|
select RT_USING_USB_DEVICE
|
|
|
|
|
default n
|
|
|
|
|
if BSP_USING_USBD
|
|
|
|
|
config BSP_USB_CONNECT_PIN
|
|
|
|
|
int "USB connect pin"
|
|
|
|
|
default 67
|
|
|
|
|
|
|
|
|
|
config BSP_USB_PULL_UP_STATUS
|
|
|
|
|
int "USB PULL UP STATUS"
|
|
|
|
|
default 0
|
|
|
|
|
endif
|
2019-07-18 11:01:19 +08:00
|
|
|
source "../libraries/HAL_Drivers/Kconfig"
|
2019-07-11 18:21:24 +08:00
|
|
|
|
2018-11-29 17:00:22 +08:00
|
|
|
endmenu
|
|
|
|
|
|
|
|
|
|
menu "Board extended module Drivers"
|
|
|
|
|
|
|
|
|
|
endmenu
|
|
|
|
|
|
|
|
|
|
endmenu
|
