rt-thread/bsp/lm3s/driverlib/gpio.c

1513 lines
52 KiB
C
Raw Normal View History

//*****************************************************************************
//
// gpio.c - API for GPIO ports
//
// Copyright (c) 2005-2009 Luminary Micro, Inc. All rights reserved.
// Software License Agreement
//
// Luminary Micro, Inc. (LMI) is supplying this software for use solely and
// exclusively on LMI's microcontroller products.
//
// The software is owned by LMI and/or its suppliers, and is protected under
// applicable copyright laws. All rights are reserved. You may not combine
// this software with "viral" open-source software in order to form a larger
// program. Any use in violation of the foregoing restrictions may subject
// the user to criminal sanctions under applicable laws, as well as to civil
// liability for the breach of the terms and conditions of this license.
//
// THIS SOFTWARE IS PROVIDED "AS IS". NO WARRANTIES, WHETHER EXPRESS, IMPLIED
// OR STATUTORY, INCLUDING, BUT NOT LIMITED TO, IMPLIED WARRANTIES OF
// MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE APPLY TO THIS SOFTWARE.
// LMI SHALL NOT, IN ANY CIRCUMSTANCES, BE LIABLE FOR SPECIAL, INCIDENTAL, OR
// CONSEQUENTIAL DAMAGES, FOR ANY REASON WHATSOEVER.
//
// This is part of revision 4694 of the Stellaris Peripheral Driver Library.
//
//*****************************************************************************
//*****************************************************************************
//
//! \addtogroup gpio_api
//! @{
//
//*****************************************************************************
#include "inc/hw_gpio.h"
#include "inc/hw_ints.h"
#include "inc/hw_memmap.h"
#include "inc/hw_sysctl.h"
#include "inc/hw_types.h"
#include "driverlib/debug.h"
#include "driverlib/gpio.h"
#include "driverlib/interrupt.h"
//*****************************************************************************
//
// The base addresses of all the GPIO modules. Both the APB and AHB apertures
// are provided.
//
//*****************************************************************************
static const unsigned long g_pulGPIOBaseAddrs[] =
{
GPIO_PORTA_BASE, GPIO_PORTA_AHB_BASE,
GPIO_PORTB_BASE, GPIO_PORTB_AHB_BASE,
GPIO_PORTC_BASE, GPIO_PORTC_AHB_BASE,
GPIO_PORTD_BASE, GPIO_PORTD_AHB_BASE,
GPIO_PORTE_BASE, GPIO_PORTE_AHB_BASE,
GPIO_PORTF_BASE, GPIO_PORTF_AHB_BASE,
GPIO_PORTG_BASE, GPIO_PORTG_AHB_BASE,
GPIO_PORTH_BASE, GPIO_PORTH_AHB_BASE,
GPIO_PORTJ_BASE, GPIO_PORTJ_AHB_BASE,
};
//*****************************************************************************
//
//! \internal
//! Checks a GPIO base address.
//!
//! \param ulPort is the base address of the GPIO port.
//!
//! This function determines if a GPIO port base address is valid.
//!
//! \return Returns \b true if the base address is valid and \b false
//! otherwise.
//
//*****************************************************************************
#ifdef DEBUG
static tBoolean
GPIOBaseValid(unsigned long ulPort)
{
return((ulPort == GPIO_PORTA_BASE) || (ulPort == GPIO_PORTA_AHB_BASE) ||
(ulPort == GPIO_PORTB_BASE) || (ulPort == GPIO_PORTB_AHB_BASE) ||
(ulPort == GPIO_PORTC_BASE) || (ulPort == GPIO_PORTC_AHB_BASE) ||
(ulPort == GPIO_PORTD_BASE) || (ulPort == GPIO_PORTD_AHB_BASE) ||
(ulPort == GPIO_PORTE_BASE) || (ulPort == GPIO_PORTE_AHB_BASE) ||
(ulPort == GPIO_PORTF_BASE) || (ulPort == GPIO_PORTF_AHB_BASE) ||
(ulPort == GPIO_PORTG_BASE) || (ulPort == GPIO_PORTG_AHB_BASE) ||
(ulPort == GPIO_PORTH_BASE) || (ulPort == GPIO_PORTH_AHB_BASE) ||
(ulPort == GPIO_PORTJ_BASE) || (ulPort == GPIO_PORTJ_AHB_BASE));
}
#endif
//*****************************************************************************
//
//! \internal
//! Gets the GPIO interrupt number.
//!
//! \param ulPort is the base address of the GPIO port.
//!
//! Given a GPIO base address, returns the corresponding interrupt number.
//!
//! \return Returns a GPIO interrupt number, or -1 if \e ulPort is invalid.
//
//*****************************************************************************
static long
GPIOGetIntNumber(unsigned long ulPort)
{
unsigned int ulInt;
//
// Determine the GPIO interrupt number for the given module.
//
switch(ulPort)
{
case GPIO_PORTA_BASE:
case GPIO_PORTA_AHB_BASE:
{
ulInt = INT_GPIOA;
break;
}
case GPIO_PORTB_BASE:
case GPIO_PORTB_AHB_BASE:
{
ulInt = INT_GPIOB;
break;
}
case GPIO_PORTC_BASE:
case GPIO_PORTC_AHB_BASE:
{
ulInt = INT_GPIOC;
break;
}
case GPIO_PORTD_BASE:
case GPIO_PORTD_AHB_BASE:
{
ulInt = INT_GPIOD;
break;
}
case GPIO_PORTE_BASE:
case GPIO_PORTE_AHB_BASE:
{
ulInt = INT_GPIOE;
break;
}
case GPIO_PORTF_BASE:
case GPIO_PORTF_AHB_BASE:
{
ulInt = INT_GPIOF;
break;
}
case GPIO_PORTG_BASE:
case GPIO_PORTG_AHB_BASE:
{
ulInt = INT_GPIOG;
break;
}
case GPIO_PORTH_BASE:
case GPIO_PORTH_AHB_BASE:
{
ulInt = INT_GPIOH;
break;
}
case GPIO_PORTJ_BASE:
case GPIO_PORTJ_AHB_BASE:
{
ulInt = INT_GPIOJ;
break;
}
default:
{
return(-1);
}
}
//
// Return GPIO interrupt number.
//
return(ulInt);
}
//*****************************************************************************
//
//! Sets the direction and mode of the specified pin(s).
//!
//! \param ulPort is the base address of the GPIO port
//! \param ucPins is the bit-packed representation of the pin(s).
//! \param ulPinIO is the pin direction and/or mode.
//!
//! This function will set the specified pin(s) on the selected GPIO port
//! as either an input or output under software control, or it will set the
//! pin to be under hardware control.
//!
//! The parameter \e ulPinIO is an enumerated data type that can be one of
//! the following values:
//!
//! - \b GPIO_DIR_MODE_IN
//! - \b GPIO_DIR_MODE_OUT
//! - \b GPIO_DIR_MODE_HW
//!
//! where \b GPIO_DIR_MODE_IN specifies that the pin will be programmed as
//! a software controlled input, \b GPIO_DIR_MODE_OUT specifies that the pin
//! will be programmed as a software controlled output, and
//! \b GPIO_DIR_MODE_HW specifies that the pin will be placed under
//! hardware control.
//!
//! The pin(s) are specified using a bit-packed byte, where each bit that is
//! set identifies the pin to be accessed, and where bit 0 of the byte
//! represents GPIO port pin 0, bit 1 represents GPIO port pin 1, and so on.
//!
//! \return None.
//
//*****************************************************************************
void
GPIODirModeSet(unsigned long ulPort, unsigned char ucPins,
unsigned long ulPinIO)
{
//
// Check the arguments.
//
ASSERT(GPIOBaseValid(ulPort));
ASSERT((ulPinIO == GPIO_DIR_MODE_IN) || (ulPinIO == GPIO_DIR_MODE_OUT) ||
(ulPinIO == GPIO_DIR_MODE_HW));
//
// Set the pin direction and mode.
//
HWREG(ulPort + GPIO_O_DIR) = ((ulPinIO & 1) ?
(HWREG(ulPort + GPIO_O_DIR) | ucPins) :
(HWREG(ulPort + GPIO_O_DIR) & ~(ucPins)));
HWREG(ulPort + GPIO_O_AFSEL) = ((ulPinIO & 2) ?
(HWREG(ulPort + GPIO_O_AFSEL) | ucPins) :
(HWREG(ulPort + GPIO_O_AFSEL) &
~(ucPins)));
}
//*****************************************************************************
//
//! Gets the direction and mode of a pin.
//!
//! \param ulPort is the base address of the GPIO port.
//! \param ucPin is the pin number.
//!
//! This function gets the direction and control mode for a specified pin on
//! the selected GPIO port. The pin can be configured as either an input or
//! output under software control, or it can be under hardware control. The
//! type of control and direction are returned as an enumerated data type.
//!
//! \return Returns one of the enumerated data types described for
//! GPIODirModeSet().
//
//*****************************************************************************
unsigned long
GPIODirModeGet(unsigned long ulPort, unsigned char ucPin)
{
unsigned long ulDir, ulAFSEL;
//
// Check the arguments.
//
ASSERT(GPIOBaseValid(ulPort));
ASSERT(ucPin < 8);
//
// Convert from a pin number to a bit position.
//
ucPin = 1 << ucPin;
//
// Return the pin direction and mode.
//
ulDir = HWREG(ulPort + GPIO_O_DIR);
ulAFSEL = HWREG(ulPort + GPIO_O_AFSEL);
return(((ulDir & ucPin) ? 1 : 0) | ((ulAFSEL & ucPin) ? 2 : 0));
}
//*****************************************************************************
//
//! Sets the interrupt type for the specified pin(s).
//!
//! \param ulPort is the base address of the GPIO port.
//! \param ucPins is the bit-packed representation of the pin(s).
//! \param ulIntType specifies the type of interrupt trigger mechanism.
//!
//! This function sets up the various interrupt trigger mechanisms for the
//! specified pin(s) on the selected GPIO port.
//!
//! The parameter \e ulIntType is an enumerated data type that can be one of
//! the following values:
//!
//! - \b GPIO_FALLING_EDGE
//! - \b GPIO_RISING_EDGE
//! - \b GPIO_BOTH_EDGES
//! - \b GPIO_LOW_LEVEL
//! - \b GPIO_HIGH_LEVEL
//!
//! where the different values describe the interrupt detection mechanism
//! (edge or level) and the particular triggering event (falling, rising,
//! or both edges for edge detect, low or high for level detect).
//!
//! The pin(s) are specified using a bit-packed byte, where each bit that is
//! set identifies the pin to be accessed, and where bit 0 of the byte
//! represents GPIO port pin 0, bit 1 represents GPIO port pin 1, and so on.
//!
//! \note In order to avoid any spurious interrupts, the user must
//! ensure that the GPIO inputs remain stable for the duration of
//! this function.
//!
//! \return None.
//
//*****************************************************************************
void
GPIOIntTypeSet(unsigned long ulPort, unsigned char ucPins,
unsigned long ulIntType)
{
//
// Check the arguments.
//
ASSERT(GPIOBaseValid(ulPort));
ASSERT((ulIntType == GPIO_FALLING_EDGE) ||
(ulIntType == GPIO_RISING_EDGE) || (ulIntType == GPIO_BOTH_EDGES) ||
(ulIntType == GPIO_LOW_LEVEL) || (ulIntType == GPIO_HIGH_LEVEL));
//
// Set the pin interrupt type.
//
HWREG(ulPort + GPIO_O_IBE) = ((ulIntType & 1) ?
(HWREG(ulPort + GPIO_O_IBE) | ucPins) :
(HWREG(ulPort + GPIO_O_IBE) & ~(ucPins)));
HWREG(ulPort + GPIO_O_IS) = ((ulIntType & 2) ?
(HWREG(ulPort + GPIO_O_IS) | ucPins) :
(HWREG(ulPort + GPIO_O_IS) & ~(ucPins)));
HWREG(ulPort + GPIO_O_IEV) = ((ulIntType & 4) ?
(HWREG(ulPort + GPIO_O_IEV) | ucPins) :
(HWREG(ulPort + GPIO_O_IEV) & ~(ucPins)));
}
//*****************************************************************************
//
//! Gets the interrupt type for a pin.
//!
//! \param ulPort is the base address of the GPIO port.
//! \param ucPin is the pin number.
//!
//! This function gets the interrupt type for a specified pin on the selected
//! GPIO port. The pin can be configured as a falling edge, rising edge, or
//! both edge detected interrupt, or it can be configured as a low level or
//! high level detected interrupt. The type of interrupt detection mechanism
//! is returned as an enumerated data type.
//!
//! \return Returns one of the enumerated data types described for
//! GPIOIntTypeSet().
//
//*****************************************************************************
unsigned long
GPIOIntTypeGet(unsigned long ulPort, unsigned char ucPin)
{
unsigned long ulIBE, ulIS, ulIEV;
//
// Check the arguments.
//
ASSERT(GPIOBaseValid(ulPort));
ASSERT(ucPin < 8);
//
// Convert from a pin number to a bit position.
//
ucPin = 1 << ucPin;
//
// Return the pin interrupt type.
//
ulIBE = HWREG(ulPort + GPIO_O_IBE);
ulIS = HWREG(ulPort + GPIO_O_IS);
ulIEV = HWREG(ulPort + GPIO_O_IEV);
return(((ulIBE & ucPin) ? 1 : 0) | ((ulIS & ucPin) ? 2 : 0) |
((ulIEV & ucPin) ? 4 : 0));
}
//*****************************************************************************
//
//! Sets the pad configuration for the specified pin(s).
//!
//! \param ulPort is the base address of the GPIO port.
//! \param ucPins is the bit-packed representation of the pin(s).
//! \param ulStrength specifies the output drive strength.
//! \param ulPinType specifies the pin type.
//!
//! This function sets the drive strength and type for the specified pin(s)
//! on the selected GPIO port. For pin(s) configured as input ports, the
//! pad is configured as requested, but the only real effect on the input
//! is the configuration of the pull-up or pull-down termination.
//!
//! The parameter \e ulStrength can be one of the following values:
//!
//! - \b GPIO_STRENGTH_2MA
//! - \b GPIO_STRENGTH_4MA
//! - \b GPIO_STRENGTH_8MA
//! - \b GPIO_STRENGTH_8MA_SC
//!
//! where \b GPIO_STRENGTH_xMA specifies either 2, 4, or 8 mA output drive
//! strength, and \b GPIO_OUT_STRENGTH_8MA_SC specifies 8 mA output drive with
//! slew control.
//!
//! The parameter \e ulPinType can be one of the following values:
//!
//! - \b GPIO_PIN_TYPE_STD
//! - \b GPIO_PIN_TYPE_STD_WPU
//! - \b GPIO_PIN_TYPE_STD_WPD
//! - \b GPIO_PIN_TYPE_OD
//! - \b GPIO_PIN_TYPE_OD_WPU
//! - \b GPIO_PIN_TYPE_OD_WPD
//! - \b GPIO_PIN_TYPE_ANALOG
//!
//! where \b GPIO_PIN_TYPE_STD* specifies a push-pull pin, \b GPIO_PIN_TYPE_OD*
//! specifies an open-drain pin, \b *_WPU specifies a weak pull-up, \b *_WPD
//! specifies a weak pull-down, and \b GPIO_PIN_TYPE_ANALOG specifies an
//! analog input (for the comparators).
//!
//! The pin(s) are specified using a bit-packed byte, where each bit that is
//! set identifies the pin to be accessed, and where bit 0 of the byte
//! represents GPIO port pin 0, bit 1 represents GPIO port pin 1, and so on.
//!
//! \return None.
//
//*****************************************************************************
void
GPIOPadConfigSet(unsigned long ulPort, unsigned char ucPins,
unsigned long ulStrength, unsigned long ulPinType)
{
//
// Check the arguments.
//
ASSERT(GPIOBaseValid(ulPort));
ASSERT((ulStrength == GPIO_STRENGTH_2MA) ||
(ulStrength == GPIO_STRENGTH_4MA) ||
(ulStrength == GPIO_STRENGTH_8MA) ||
(ulStrength == GPIO_STRENGTH_8MA_SC));
ASSERT((ulPinType == GPIO_PIN_TYPE_STD) ||
(ulPinType == GPIO_PIN_TYPE_STD_WPU) ||
(ulPinType == GPIO_PIN_TYPE_STD_WPD) ||
(ulPinType == GPIO_PIN_TYPE_OD) ||
(ulPinType == GPIO_PIN_TYPE_OD_WPU) ||
(ulPinType == GPIO_PIN_TYPE_OD_WPD) ||
(ulPinType == GPIO_PIN_TYPE_ANALOG))
//
// Set the output drive strength.
//
HWREG(ulPort + GPIO_O_DR2R) = ((ulStrength & 1) ?
(HWREG(ulPort + GPIO_O_DR2R) | ucPins) :
(HWREG(ulPort + GPIO_O_DR2R) & ~(ucPins)));
HWREG(ulPort + GPIO_O_DR4R) = ((ulStrength & 2) ?
(HWREG(ulPort + GPIO_O_DR4R) | ucPins) :
(HWREG(ulPort + GPIO_O_DR4R) & ~(ucPins)));
HWREG(ulPort + GPIO_O_DR8R) = ((ulStrength & 4) ?
(HWREG(ulPort + GPIO_O_DR8R) | ucPins) :
(HWREG(ulPort + GPIO_O_DR8R) & ~(ucPins)));
HWREG(ulPort + GPIO_O_SLR) = ((ulStrength & 8) ?
(HWREG(ulPort + GPIO_O_SLR) | ucPins) :
(HWREG(ulPort + GPIO_O_SLR) & ~(ucPins)));
//
// Set the pin type.
//
HWREG(ulPort + GPIO_O_ODR) = ((ulPinType & 1) ?
(HWREG(ulPort + GPIO_O_ODR) | ucPins) :
(HWREG(ulPort + GPIO_O_ODR) & ~(ucPins)));
HWREG(ulPort + GPIO_O_PUR) = ((ulPinType & 2) ?
(HWREG(ulPort + GPIO_O_PUR) | ucPins) :
(HWREG(ulPort + GPIO_O_PUR) & ~(ucPins)));
HWREG(ulPort + GPIO_O_PDR) = ((ulPinType & 4) ?
(HWREG(ulPort + GPIO_O_PDR) | ucPins) :
(HWREG(ulPort + GPIO_O_PDR) & ~(ucPins)));
HWREG(ulPort + GPIO_O_DEN) = ((ulPinType & 8) ?
(HWREG(ulPort + GPIO_O_DEN) | ucPins) :
(HWREG(ulPort + GPIO_O_DEN) & ~(ucPins)));
//
// Set the analog mode select register. This register only appears in
// DustDevil-class (and later) devices, but is a harmless write on
// Sandstorm- and Fury-class devices.
//
HWREG(ulPort + GPIO_O_AMSEL) =
((ulPinType == GPIO_PIN_TYPE_ANALOG) ?
(HWREG(ulPort + GPIO_O_AMSEL) | ucPins) :
(HWREG(ulPort + GPIO_O_AMSEL) & ~(ucPins)));
}
//*****************************************************************************
//
//! Gets the pad configuration for a pin.
//!
//! \param ulPort is the base address of the GPIO port.
//! \param ucPin is the pin number.
//! \param pulStrength is a pointer to storage for the output drive strength.
//! \param pulPinType is a pointer to storage for the output drive type.
//!
//! This function gets the pad configuration for a specified pin on the
//! selected GPIO port. The values returned in \e pulStrength and
//! \e pulPinType correspond to the values used in GPIOPadConfigSet(). This
//! function also works for pin(s) configured as input pin(s); however, the
//! only meaningful data returned is whether the pin is terminated with a
//! pull-up or down resistor.
//!
//! \return None
//
//*****************************************************************************
void
GPIOPadConfigGet(unsigned long ulPort, unsigned char ucPin,
unsigned long *pulStrength, unsigned long *pulPinType)
{
unsigned long ulTemp1, ulTemp2, ulTemp3, ulTemp4;
//
// Check the arguments.
//
ASSERT(GPIOBaseValid(ulPort));
ASSERT(ucPin < 8);
//
// Convert from a pin number to a bit position.
//
ucPin = (1 << ucPin);
//
// Get the drive strength for this pin.
//
ulTemp1 = HWREG(ulPort + GPIO_O_DR2R);
ulTemp2 = HWREG(ulPort + GPIO_O_DR4R);
ulTemp3 = HWREG(ulPort + GPIO_O_DR8R);
ulTemp4 = HWREG(ulPort + GPIO_O_SLR);
*pulStrength = (((ulTemp1 & ucPin) ? 1 : 0) | ((ulTemp2 & ucPin) ? 2 : 0) |
((ulTemp3 & ucPin) ? 4 : 0) | ((ulTemp4 & ucPin) ? 8 : 0));
//
// Get the pin type.
//
ulTemp1 = HWREG(ulPort + GPIO_O_ODR);
ulTemp2 = HWREG(ulPort + GPIO_O_PUR);
ulTemp3 = HWREG(ulPort + GPIO_O_PDR);
ulTemp4 = HWREG(ulPort + GPIO_O_DEN);
*pulPinType = (((ulTemp1 & ucPin) ? 1 : 0) | ((ulTemp2 & ucPin) ? 2 : 0) |
((ulTemp3 & ucPin) ? 4 : 0) | ((ulTemp4 & ucPin) ? 8 : 0));
}
//*****************************************************************************
//
//! Enables interrupts for the specified pin(s).
//!
//! \param ulPort is the base address of the GPIO port.
//! \param ucPins is the bit-packed representation of the pin(s).
//!
//! Unmasks the interrupt for the specified pin(s).
//!
//! The pin(s) are specified using a bit-packed byte, where each bit that is
//! set identifies the pin to be accessed, and where bit 0 of the byte
//! represents GPIO port pin 0, bit 1 represents GPIO port pin 1, and so on.
//!
//! \return None.
//
//*****************************************************************************
void
GPIOPinIntEnable(unsigned long ulPort, unsigned char ucPins)
{
//
// Check the arguments.
//
ASSERT(GPIOBaseValid(ulPort));
//
// Enable the interrupts.
//
HWREG(ulPort + GPIO_O_IM) |= ucPins;
}
//*****************************************************************************
//
//! Disables interrupts for the specified pin(s).
//!
//! \param ulPort is the base address of the GPIO port.
//! \param ucPins is the bit-packed representation of the pin(s).
//!
//! Masks the interrupt for the specified pin(s).
//!
//! The pin(s) are specified using a bit-packed byte, where each bit that is
//! set identifies the pin to be accessed, and where bit 0 of the byte
//! represents GPIO port pin 0, bit 1 represents GPIO port pin 1, and so on.
//!
//! \return None.
//
//*****************************************************************************
void
GPIOPinIntDisable(unsigned long ulPort, unsigned char ucPins)
{
//
// Check the arguments.
//
ASSERT(GPIOBaseValid(ulPort));
//
// Disable the interrupts.
//
HWREG(ulPort + GPIO_O_IM) &= ~(ucPins);
}
//*****************************************************************************
//
//! Gets interrupt status for the specified GPIO port.
//!
//! \param ulPort is the base address of the GPIO port.
//! \param bMasked specifies whether masked or raw interrupt status is
//! returned.
//!
//! If \e bMasked is set as \b true, then the masked interrupt status is
//! returned; otherwise, the raw interrupt status will be returned.
//!
//! \return Returns a bit-packed byte, where each bit that is set identifies
//! an active masked or raw interrupt, and where bit 0 of the byte
//! represents GPIO port pin 0, bit 1 represents GPIO port pin 1, and so on.
//! Bits 31:8 should be ignored.
//
//*****************************************************************************
long
GPIOPinIntStatus(unsigned long ulPort, tBoolean bMasked)
{
//
// Check the arguments.
//
ASSERT(GPIOBaseValid(ulPort));
//
// Return the interrupt status.
//
if(bMasked)
{
return(HWREG(ulPort + GPIO_O_MIS));
}
else
{
return(HWREG(ulPort + GPIO_O_RIS));
}
}
//*****************************************************************************
//
//! Clears the interrupt for the specified pin(s).
//!
//! \param ulPort is the base address of the GPIO port.
//! \param ucPins is the bit-packed representation of the pin(s).
//!
//! Clears the interrupt for the specified pin(s).
//!
//! The pin(s) are specified using a bit-packed byte, where each bit that is
//! set identifies the pin to be accessed, and where bit 0 of the byte
//! represents GPIO port pin 0, bit 1 represents GPIO port pin 1, and so on.
//!
//! \note Since there is a write buffer in the Cortex-M3 processor, it may take
//! several clock cycles before the interrupt source is actually cleared.
//! Therefore, it is recommended that the interrupt source be cleared early in
//! the interrupt handler (as opposed to the very last action) to avoid
//! returning from the interrupt handler before the interrupt source is
//! actually cleared. Failure to do so may result in the interrupt handler
//! being immediately reentered (since NVIC still sees the interrupt source
//! asserted).
//!
//! \return None.
//
//*****************************************************************************
void
GPIOPinIntClear(unsigned long ulPort, unsigned char ucPins)
{
//
// Check the arguments.
//
ASSERT(GPIOBaseValid(ulPort));
//
// Clear the interrupts.
//
HWREG(ulPort + GPIO_O_ICR) = ucPins;
}
//*****************************************************************************
//
//! Registers an interrupt handler for a GPIO port.
//!
//! \param ulPort is the base address of the GPIO port.
//! \param pfnIntHandler is a pointer to the GPIO port interrupt handling
//! function.
//!
//! This function will ensure that the interrupt handler specified by
//! \e pfnIntHandler is called when an interrupt is detected from the selected
//! GPIO port. This function will also enable the corresponding GPIO interrupt
//! in the interrupt controller; individual pin interrupts and interrupt
//! sources must be enabled with GPIOPinIntEnable().
//!
//! \sa IntRegister() for important information about registering interrupt
//! handlers.
//!
//! \return None.
//
//*****************************************************************************
void
GPIOPortIntRegister(unsigned long ulPort, void (*pfnIntHandler)(void))
{
//
// Check the arguments.
//
ASSERT(GPIOBaseValid(ulPort));
//
// Get the interrupt number associated with the specified GPIO.
//
ulPort = GPIOGetIntNumber(ulPort);
//
// Register the interrupt handler.
//
IntRegister(ulPort, pfnIntHandler);
//
// Enable the GPIO interrupt.
//
IntEnable(ulPort);
}
//*****************************************************************************
//
//! Removes an interrupt handler for a GPIO port.
//!
//! \param ulPort is the base address of the GPIO port.
//!
//! This function will unregister the interrupt handler for the specified
//! GPIO port. This function will also disable the corresponding
//! GPIO port interrupt in the interrupt controller; individual GPIO interrupts
//! and interrupt sources must be disabled with GPIOPinIntDisable().
//!
//! \sa IntRegister() for important information about registering interrupt
//! handlers.
//!
//! \return None.
//
//*****************************************************************************
void
GPIOPortIntUnregister(unsigned long ulPort)
{
//
// Check the arguments.
//
ASSERT(GPIOBaseValid(ulPort));
//
// Get the interrupt number associated with the specified GPIO.
//
ulPort = GPIOGetIntNumber(ulPort);
//
// Disable the GPIO interrupt.
//
IntDisable(ulPort);
//
// Unregister the interrupt handler.
//
IntUnregister(ulPort);
}
//*****************************************************************************
//
//! Reads the values present of the specified pin(s).
//!
//! \param ulPort is the base address of the GPIO port.
//! \param ucPins is the bit-packed representation of the pin(s).
//!
//! The values at the specified pin(s) are read, as specified by \e ucPins.
//! Values are returned for both input and output pin(s), and the value
//! for pin(s) that are not specified by \e ucPins are set to 0.
//!
//! The pin(s) are specified using a bit-packed byte, where each bit that is
//! set identifies the pin to be accessed, and where bit 0 of the byte
//! represents GPIO port pin 0, bit 1 represents GPIO port pin 1, and so on.
//!
//! \return Returns a bit-packed byte providing the state of the specified
//! pin, where bit 0 of the byte represents GPIO port pin 0, bit 1 represents
//! GPIO port pin 1, and so on. Any bit that is not specified by \e ucPins
//! is returned as a 0. Bits 31:8 should be ignored.
//
//*****************************************************************************
long
GPIOPinRead(unsigned long ulPort, unsigned char ucPins)
{
//
// Check the arguments.
//
ASSERT(GPIOBaseValid(ulPort));
//
// Return the pin value(s).
//
return(HWREG(ulPort + (GPIO_O_DATA + (ucPins << 2))));
}
//*****************************************************************************
//
//! Writes a value to the specified pin(s).
//!
//! \param ulPort is the base address of the GPIO port.
//! \param ucPins is the bit-packed representation of the pin(s).
//! \param ucVal is the value to write to the pin(s).
//!
//! Writes the corresponding bit values to the output pin(s) specified by
//! \e ucPins. Writing to a pin configured as an input pin has no effect.
//!
//! The pin(s) are specified using a bit-packed byte, where each bit that is
//! set identifies the pin to be accessed, and where bit 0 of the byte
//! represents GPIO port pin 0, bit 1 represents GPIO port pin 1, and so on.
//!
//! \return None.
//
//*****************************************************************************
void
GPIOPinWrite(unsigned long ulPort, unsigned char ucPins, unsigned char ucVal)
{
//
// Check the arguments.
//
ASSERT(GPIOBaseValid(ulPort));
//
// Write the pins.
//
HWREG(ulPort + (GPIO_O_DATA + (ucPins << 2))) = ucVal;
}
//*****************************************************************************
//
//! Configures pin(s) for use as analog-to-digital converter inputs.
//!
//! \param ulPort is the base address of the GPIO port.
//! \param ucPins is the bit-packed representation of the pin(s).
//!
//! The analog-to-digital converter input pins must be properly configured
//! to function correctly on DustDevil-class devices. This function provides
//! the proper configuration for those pin(s).
//!
//! The pin(s) are specified using a bit-packed byte, where each bit that is
//! set identifies the pin to be accessed, and where bit 0 of the byte
//! represents GPIO port pin 0, bit 1 represents GPIO port pin 1, and so on.
//!
//! \note This cannot be used to turn any pin into an ADC input; it only
//! configures an ADC input pin for proper operation.
//!
//! \return None.
//
//*****************************************************************************
void
GPIOPinTypeADC(unsigned long ulPort, unsigned char ucPins)
{
//
// Check the arguments.
//
ASSERT(GPIOBaseValid(ulPort));
//
// Make the pin(s) be inputs.
//
GPIODirModeSet(ulPort, ucPins, GPIO_DIR_MODE_IN);
//
// Set the pad(s) for analog operation.
//
GPIOPadConfigSet(ulPort, ucPins, GPIO_STRENGTH_2MA, GPIO_PIN_TYPE_ANALOG);
}
//*****************************************************************************
//
//! Configures pin(s) for use as a CAN device.
//!
//! \param ulPort is the base address of the GPIO port.
//! \param ucPins is the bit-packed representation of the pin(s).
//!
//! The CAN pins must be properly configured for the CAN peripherals to
//! function correctly. This function provides a typical configuration for
//! those pin(s); other configurations may work as well depending upon the
//! board setup (for example, using the on-chip pull-ups).
//!
//! The pin(s) are specified using a bit-packed byte, where each bit that is
//! set identifies the pin to be accessed, and where bit 0 of the byte
//! represents GPIO port pin 0, bit 1 represents GPIO port pin 1, and so on.
//!
//! \note This cannot be used to turn any pin into a CAN pin; it only
//! configures a CAN pin for proper operation.
//!
//! \return None.
//
//*****************************************************************************
void
GPIOPinTypeCAN(unsigned long ulPort, unsigned char ucPins)
{
//
// Check the arguments.
//
ASSERT(GPIOBaseValid(ulPort));
//
// Make the pin(s) be inputs.
//
GPIODirModeSet(ulPort, ucPins, GPIO_DIR_MODE_HW);
//
// Set the pad(s) for standard push-pull operation.
//
GPIOPadConfigSet(ulPort, ucPins, GPIO_STRENGTH_8MA, GPIO_PIN_TYPE_STD);
}
//*****************************************************************************
//
//! Configures pin(s) for use as an analog comparator input.
//!
//! \param ulPort is the base address of the GPIO port.
//! \param ucPins is the bit-packed representation of the pin(s).
//!
//! The analog comparator input pins must be properly configured for the analog
//! comparator to function correctly. This function provides the proper
//! configuration for those pin(s).
//!
//! The pin(s) are specified using a bit-packed byte, where each bit that is
//! set identifies the pin to be accessed, and where bit 0 of the byte
//! represents GPIO port pin 0, bit 1 represents GPIO port pin 1, and so on.
//!
//! \note This cannot be used to turn any pin into an analog comparator input;
//! it only configures an analog comparator pin for proper operation.
//!
//! \return None.
//
//*****************************************************************************
void
GPIOPinTypeComparator(unsigned long ulPort, unsigned char ucPins)
{
//
// Check the arguments.
//
ASSERT(GPIOBaseValid(ulPort));
//
// Make the pin(s) be inputs.
//
GPIODirModeSet(ulPort, ucPins, GPIO_DIR_MODE_IN);
//
// Set the pad(s) for analog operation.
//
GPIOPadConfigSet(ulPort, ucPins, GPIO_STRENGTH_2MA, GPIO_PIN_TYPE_ANALOG);
}
//*****************************************************************************
//
//! Configures pin(s) for use as GPIO inputs.
//!
//! \param ulPort is the base address of the GPIO port.
//! \param ucPins is the bit-packed representation of the pin(s).
//!
//! The GPIO pins must be properly configured in order to function correctly as
//! GPIO inputs; this is especially true of Fury-class devices where the
//! digital input enable is turned off by default. This function provides the
//! proper configuration for those pin(s).
//!
//! The pin(s) are specified using a bit-packed byte, where each bit that is
//! set identifies the pin to be accessed, and where bit 0 of the byte
//! represents GPIO port pin 0, bit 1 represents GPIO port pin 1, and so on.
//!
//! \return None.
//
//*****************************************************************************
void
GPIOPinTypeGPIOInput(unsigned long ulPort, unsigned char ucPins)
{
//
// Check the arguments.
//
ASSERT(GPIOBaseValid(ulPort));
//
// Make the pin(s) be inputs.
//
GPIODirModeSet(ulPort, ucPins, GPIO_DIR_MODE_IN);
//
// Set the pad(s) for standard push-pull operation.
//
GPIOPadConfigSet(ulPort, ucPins, GPIO_STRENGTH_2MA, GPIO_PIN_TYPE_STD);
}
//*****************************************************************************
//
//! Configures pin(s) for use as GPIO outputs.
//!
//! \param ulPort is the base address of the GPIO port.
//! \param ucPins is the bit-packed representation of the pin(s).
//!
//! The GPIO pins must be properly configured in order to function correctly as
//! GPIO outputs; this is especially true of Fury-class devices where the
//! digital input enable is turned off by default. This function provides the
//! proper configuration for those pin(s).
//!
//! The pin(s) are specified using a bit-packed byte, where each bit that is
//! set identifies the pin to be accessed, and where bit 0 of the byte
//! represents GPIO port pin 0, bit 1 represents GPIO port pin 1, and so on.
//!
//! \return None.
//
//*****************************************************************************
void
GPIOPinTypeGPIOOutput(unsigned long ulPort, unsigned char ucPins)
{
//
// Check the arguments.
//
ASSERT(GPIOBaseValid(ulPort));
//
// Make the pin(s) be outputs.
//
GPIODirModeSet(ulPort, ucPins, GPIO_DIR_MODE_OUT);
//
// Set the pad(s) for standard push-pull operation.
//
GPIOPadConfigSet(ulPort, ucPins, GPIO_STRENGTH_2MA, GPIO_PIN_TYPE_STD);
}
//*****************************************************************************
//
//! Configures pin(s) for use as GPIO open drain outputs.
//!
//! \param ulPort is the base address of the GPIO port.
//! \param ucPins is the bit-packed representation of the pin(s).
//!
//! The GPIO pins must be properly configured in order to function correctly as
//! GPIO outputs; this is especially true of Fury-class devices where the
//! digital input enable is turned off by default. This function provides the
//! proper configuration for those pin(s).
//!
//! The pin(s) are specified using a bit-packed byte, where each bit that is
//! set identifies the pin to be accessed, and where bit 0 of the byte
//! represents GPIO port pin 0, bit 1 represents GPIO port pin 1, and so on.
//!
//! \return None.
//
//*****************************************************************************
void
GPIOPinTypeGPIOOutputOD(unsigned long ulPort, unsigned char ucPins)
{
//
// Check the arguments.
//
ASSERT(GPIOBaseValid(ulPort));
//
// Make the pin(s) be outputs.
//
GPIODirModeSet(ulPort, ucPins, GPIO_DIR_MODE_OUT);
//
// Set the pad(s) for standard push-pull operation.
//
GPIOPadConfigSet(ulPort, ucPins, GPIO_STRENGTH_2MA, GPIO_PIN_TYPE_OD);
}
//*****************************************************************************
//
//! Configures pin(s) for use by the I2C peripheral.
//!
//! \param ulPort is the base address of the GPIO port.
//! \param ucPins is the bit-packed representation of the pin(s).
//!
//! The I2C pins must be properly configured for the I2C peripheral to function
//! correctly. This function provides the proper configuration for those
//! pin(s).
//!
//! The pin(s) are specified using a bit-packed byte, where each bit that is
//! set identifies the pin to be accessed, and where bit 0 of the byte
//! represents GPIO port pin 0, bit 1 represents GPIO port pin 1, and so on.
//!
//! \note This cannot be used to turn any pin into an I2C pin; it only
//! configures an I2C pin for proper operation.
//!
//! \return None.
//
//*****************************************************************************
void
GPIOPinTypeI2C(unsigned long ulPort, unsigned char ucPins)
{
//
// Check the arguments.
//
ASSERT(GPIOBaseValid(ulPort));
//
// Make the pin(s) be peripheral controlled.
//
GPIODirModeSet(ulPort, ucPins, GPIO_DIR_MODE_HW);
//
// Set the pad(s) for open-drain operation with a weak pull-up.
//
GPIOPadConfigSet(ulPort, ucPins, GPIO_STRENGTH_2MA, GPIO_PIN_TYPE_OD_WPU);
}
//*****************************************************************************
//
//! Configures pin(s) for use by the PWM peripheral.
//!
//! \param ulPort is the base address of the GPIO port.
//! \param ucPins is the bit-packed representation of the pin(s).
//!
//! The PWM pins must be properly configured for the PWM peripheral to function
//! correctly. This function provides a typical configuration for those
//! pin(s); other configurations may work as well depending upon the board
//! setup (for example, using the on-chip pull-ups).
//!
//! The pin(s) are specified using a bit-packed byte, where each bit that is
//! set identifies the pin to be accessed, and where bit 0 of the byte
//! represents GPIO port pin 0, bit 1 represents GPIO port pin 1, and so on.
//!
//! \note This cannot be used to turn any pin into a PWM pin; it only
//! configures a PWM pin for proper operation.
//!
//! \return None.
//
//*****************************************************************************
void
GPIOPinTypePWM(unsigned long ulPort, unsigned char ucPins)
{
//
// Check the arguments.
//
ASSERT(GPIOBaseValid(ulPort));
//
// Make the pin(s) be peripheral controlled.
//
GPIODirModeSet(ulPort, ucPins, GPIO_DIR_MODE_HW);
//
// Set the pad(s) for standard push-pull operation.
//
GPIOPadConfigSet(ulPort, ucPins, GPIO_STRENGTH_2MA, GPIO_PIN_TYPE_STD);
}
//*****************************************************************************
//
//! Configures pin(s) for use by the QEI peripheral.
//!
//! \param ulPort is the base address of the GPIO port.
//! \param ucPins is the bit-packed representation of the pin(s).
//!
//! The QEI pins must be properly configured for the QEI peripheral to function
//! correctly. This function provides a typical configuration for those
//! pin(s); other configurations may work as well depending upon the board
//! setup (for example, not using the on-chip pull-ups).
//!
//! The pin(s) are specified using a bit-packed byte, where each bit that is
//! set identifies the pin to be accessed, and where bit 0 of the byte
//! represents GPIO port pin 0, bit 1 represents GPIO port pin 1, and so on.
//!
//! \note This cannot be used to turn any pin into a QEI pin; it only
//! configures a QEI pin for proper operation.
//!
//! \return None.
//
//*****************************************************************************
void
GPIOPinTypeQEI(unsigned long ulPort, unsigned char ucPins)
{
//
// Check the arguments.
//
ASSERT(GPIOBaseValid(ulPort));
//
// Make the pin(s) be peripheral controlled.
//
GPIODirModeSet(ulPort, ucPins, GPIO_DIR_MODE_HW);
//
// Set the pad(s) for standard push-pull operation with a weak pull-up.
//
GPIOPadConfigSet(ulPort, ucPins, GPIO_STRENGTH_2MA, GPIO_PIN_TYPE_STD_WPU);
}
//*****************************************************************************
//
//! Configures pin(s) for use by the SSI peripheral.
//!
//! \param ulPort is the base address of the GPIO port.
//! \param ucPins is the bit-packed representation of the pin(s).
//!
//! The SSI pins must be properly configured for the SSI peripheral to function
//! correctly. This function provides a typical configuration for those
//! pin(s); other configurations may work as well depending upon the board
//! setup (for example, using the on-chip pull-ups).
//!
//! The pin(s) are specified using a bit-packed byte, where each bit that is
//! set identifies the pin to be accessed, and where bit 0 of the byte
//! represents GPIO port pin 0, bit 1 represents GPIO port pin 1, and so on.
//!
//! \note This cannot be used to turn any pin into a SSI pin; it only
//! configures a SSI pin for proper operation.
//!
//! \return None.
//
//*****************************************************************************
void
GPIOPinTypeSSI(unsigned long ulPort, unsigned char ucPins)
{
//
// Check the arguments.
//
ASSERT(GPIOBaseValid(ulPort));
//
// Make the pin(s) be peripheral controlled.
//
GPIODirModeSet(ulPort, ucPins, GPIO_DIR_MODE_HW);
//
// Set the pad(s) for standard push-pull operation.
//
GPIOPadConfigSet(ulPort, ucPins, GPIO_STRENGTH_2MA, GPIO_PIN_TYPE_STD);
}
//*****************************************************************************
//
//! Configures pin(s) for use by the Timer peripheral.
//!
//! \param ulPort is the base address of the GPIO port.
//! \param ucPins is the bit-packed representation of the pin(s).
//!
//! The CCP pins must be properly configured for the timer peripheral to
//! function correctly. This function provides a typical configuration for
//! those pin(s); other configurations may work as well depending upon the
//! board setup (for example, using the on-chip pull-ups).
//!
//! The pin(s) are specified using a bit-packed byte, where each bit that is
//! set identifies the pin to be accessed, and where bit 0 of the byte
//! represents GPIO port pin 0, bit 1 represents GPIO port pin 1, and so on.
//!
//! \note This cannot be used to turn any pin into a timer pin; it only
//! configures a timer pin for proper operation.
//!
//! \return None.
//
//*****************************************************************************
void
GPIOPinTypeTimer(unsigned long ulPort, unsigned char ucPins)
{
//
// Check the arguments.
//
ASSERT(GPIOBaseValid(ulPort));
//
// Make the pin(s) be peripheral controlled.
//
GPIODirModeSet(ulPort, ucPins, GPIO_DIR_MODE_HW);
//
// Set the pad(s) for standard push-pull operation.
//
GPIOPadConfigSet(ulPort, ucPins, GPIO_STRENGTH_2MA, GPIO_PIN_TYPE_STD);
}
//*****************************************************************************
//
//! Configures pin(s) for use by the UART peripheral.
//!
//! \param ulPort is the base address of the GPIO port.
//! \param ucPins is the bit-packed representation of the pin(s).
//!
//! The UART pins must be properly configured for the UART peripheral to
//! function correctly. This function provides a typical configuration for
//! those pin(s); other configurations may work as well depending upon the
//! board setup (for example, using the on-chip pull-ups).
//!
//! The pin(s) are specified using a bit-packed byte, where each bit that is
//! set identifies the pin to be accessed, and where bit 0 of the byte
//! represents GPIO port pin 0, bit 1 represents GPIO port pin 1, and so on.
//!
//! \note This cannot be used to turn any pin into a UART pin; it only
//! configures a UART pin for proper operation.
//!
//! \return None.
//
//*****************************************************************************
void
GPIOPinTypeUART(unsigned long ulPort, unsigned char ucPins)
{
//
// Check the arguments.
//
ASSERT(GPIOBaseValid(ulPort));
//
// Make the pin(s) be peripheral controlled.
//
GPIODirModeSet(ulPort, ucPins, GPIO_DIR_MODE_HW);
//
// Set the pad(s) for standard push-pull operation.
//
GPIOPadConfigSet(ulPort, ucPins, GPIO_STRENGTH_2MA, GPIO_PIN_TYPE_STD);
}
//*****************************************************************************
//
//! Configures pin(s) for use by the USB peripheral.
//!
//! \param ulPort is the base address of the GPIO port.
//! \param ucPins is the bit-packed representation of the pin(s).
//!
//! Some USB digital pins must be properly configured for the USB peripheral to
//! function correctly. This function provides a typical configuration for
//! the digital USB pin(s); other configurations may work as well depending
//! upon the board setup (for example, using the on-chip pull-ups).
//!
//! The pin(s) are specified using a bit-packed byte, where each bit that is
//! set identifies the pin to be accessed, and where bit 0 of the byte
//! represents GPIO port pin 0, bit 1 represents GPIO port pin 1, and so on.
//!
//! \note This cannot be used to turn any pin into a USB pin; it only
//! configures a USB pin for proper operation.
//!
//! \return None.
//
//*****************************************************************************
void
GPIOPinTypeUSBDigital(unsigned long ulPort, unsigned char ucPins)
{
//
// Check the arguments.
//
ASSERT(GPIOBaseValid(ulPort));
//
// Make the pin(s) be peripheral controlled.
//
GPIODirModeSet(ulPort, ucPins, GPIO_DIR_MODE_HW);
//
// Set the pad(s) for standard push-pull operation.
//
GPIOPadConfigSet(ulPort, ucPins, GPIO_STRENGTH_2MA, GPIO_PIN_TYPE_STD);
}
//*****************************************************************************
//
//! Configures pin(s) for use by the USB peripheral.
//!
//! \param ulPort is the base address of the GPIO port.
//! \param ucPins is the bit-packed representation of the pin(s).
//!
//! Some USB analog pins must be properly configured for the USB peripheral to
//! function correctly. This function provides the proper configuration for
//! those pin(s).
//!
//! The pin(s) are specified using a bit-packed byte, where each bit that is
//! set identifies the pin to be accessed, and where bit 0 of the byte
//! represents GPIO port pin 0, bit 1 represents GPIO port pin 1, and so on.
//!
//! \note This cannot be used to turn any pin into a USB pin; it only
//! configures a USB pin for proper operation.
//!
//! \return None.
//
//*****************************************************************************
void
GPIOPinTypeUSBAnalog(unsigned long ulPort, unsigned char ucPins)
{
//
// Check the arguments.
//
ASSERT(GPIOBaseValid(ulPort));
//
// Make the pin(s) be inputs.
//
GPIODirModeSet(ulPort, ucPins, GPIO_DIR_MODE_IN);
//
// Set the pad(s) for analog operation.
//
GPIOPadConfigSet(ulPort, ucPins, GPIO_STRENGTH_2MA, GPIO_PIN_TYPE_ANALOG);
}
//*****************************************************************************
//
//! Configures pin(s) for use by the I2S peripheral.
//!
//! \param ulPort is the base address of the GPIO port.
//! \param ucPins is the bit-packed representation of the pin(s).
//!
//! Some I2S pins must be properly configured for the I2S peripheral to
//! function correctly. This function provides a typical configuration for
//! the digital I2S pin(s); other configurations may work as well depending
//! upon the board setup (for example, using the on-chip pull-ups).
//!
//! The pin(s) are specified using a bit-packed byte, where each bit that is
//! set identifies the pin to be accessed, and where bit 0 of the byte
//! represents GPIO port pin 0, bit 1 represents GPIO port pin 1, and so on.
//!
//! \note This cannot be used to turn any pin into a I2S pin; it only
//! configures a I2S pin for proper operation.
//!
//! \return None.
//
//*****************************************************************************
void
GPIOPinTypeI2S(unsigned long ulPort, unsigned char ucPins)
{
//
// Check the arguments.
//
ASSERT(GPIOBaseValid(ulPort));
//
// Make the pin(s) be peripheral controlled.
//
GPIODirModeSet(ulPort, ucPins, GPIO_DIR_MODE_HW);
//
// Set the pad(s) for standard push-pull operation.
//
GPIOPadConfigSet(ulPort, ucPins, GPIO_STRENGTH_2MA, GPIO_PIN_TYPE_STD);
}
//*****************************************************************************
//
//! Configures the alternate function of a GPIO pin.
//!
//! \param ulPinConfig is the pin configuration value, specified as one of the
//! \b GPIO_P??_??? values.
//!
//! This function configures the pin mux that selects the peripheral function
//! associated with a particular GPIO pin. Only one peripheral function at a
//! time can be associated with a GPIO pin, and each peripheral function should
//! only be associated with a single GPIO pin at a time (despite the fact that
//! many of them can be associated with more than one GPIO pin).
//!
//! \note This function is only valid on Tempest-class devices.
//!
//! \return None.
//
//*****************************************************************************
void
GPIOPinConfigure(unsigned long ulPinConfig)
{
unsigned long ulBase, ulShift;
//
// Check the argument.
//
ASSERT(((ulPinConfig >> 16) & 0xff) < 9);
ASSERT(((ulPinConfig >> 8) & 0xe3) == 0);
//
// Extract the base address index from the input value.
//
ulBase = (ulPinConfig >> 16) & 0xff;
//
// Get the base address of the GPIO module, selecting either the APB or the
// AHB aperture as appropriate.
//
if(HWREG(SYSCTL_GPIOHSCTL) & (1 << ulBase))
{
ulBase = g_pulGPIOBaseAddrs[(ulBase << 1) + 1];
}
else
{
ulBase = g_pulGPIOBaseAddrs[ulBase << 1];
}
//
// Extract the shift from the input value.
//
ulShift = (ulPinConfig >> 8) & 0xff;
//
// Write the requested pin muxing value for this GPIO pin.
//
HWREG(ulBase + GPIO_O_PCTL) = ((HWREG(ulBase + GPIO_O_PCTL) &
~(0xf << ulShift)) |
((ulPinConfig & 0xf) << ulShift));
}
//*****************************************************************************
//
// Close the Doxygen group.
//! @}
//
//*****************************************************************************