rt-thread/bsp/imxrt/imxrt1021-nxp-evk/board/Kconfig

menu "Hardware Drivers"

config BSP_USING_QSPIFLASH
    bool
    default y

config SOC_IMXRT1021DAG5A
    bool
    select SOC_MIMXRT1020_SERIES
    select RT_USING_COMPONENTS_INIT
    select RT_USING_USER_MAIN
    select SOC_IMXRT1020_SERIES
    default y


menu "On-chip Peripheral Drivers"

    config BSP_USING_DMA
        bool "Enable DMA"
        default n

    config BSP_USING_GPIO
        bool "Enable GPIO"
        select RT_USING_PIN
        default y

    menuconfig BSP_USING_CAN
        bool "Enable CAN"
        select RT_USING_CAN
        default n

        if BSP_USING_CAN
            config BSP_USING_CAN1
                bool "Enable CAN1"
                default y
        endif

    menuconfig BSP_USING_LPUART
        bool "Enable UART"
        select RT_USING_SERIAL
        default y

        if BSP_USING_LPUART
            config BSP_USING_LPUART1
                bool "Enable LPUART1"
                default y

                config BSP_LPUART1_RX_USING_DMA
                    bool "Enable LPUART1 RX DMA"
                    depends on BSP_USING_LPUART1
                    select BSP_USING_DMA
                    select RT_SERIAL_USING_DMA
                    default n

                    config BSP_LPUART1_RX_DMA_CHANNEL
                        depends on BSP_LPUART1_RX_USING_DMA
                        int "Set LPUART1 RX DMA channel (0-32)"
                        default 0

                config BSP_LPUART1_TX_USING_DMA
                    bool "Enable LPUART1 TX DMA"
                    depends on BSP_USING_LPUART1
                    select BSP_USING_DMA
                    select RT_SERIAL_USING_DMA
                    default n

                    config BSP_LPUART1_TX_DMA_CHANNEL
                        depends on BSP_LPUART1_TX_USING_DMA
                        int "Set LPUART1 TX DMA channel (0-32)"
                        default 1
        endif
    menuconfig BSP_USING_HWTIMER
            bool "Enable GPT"
            default n
            select RT_USING_HWTIMER
            if BSP_USING_TIM
                config BSP_USING_HWTIMER1
                    bool "Enable GPT1"
                    default n

                config BSP_USING_HWTIMER2
                    bool "Enable GPT2"
                    default n
            endif
    menuconfig BSP_USING_PWM
        bool "Enable PWM"
        default n
        select RT_USING_PWM
        if BSP_USING_PWM
            menuconfig BSP_USING_PWM1
                bool "Enable output pwm1"
                default n
                if BSP_USING_PWM1
                    config BSP_USING_PWM1_CH3
                        bool "Enable PWM1 channel3"
                        default n
                endif

            menuconfig BSP_USING_PWM4
                bool "Enable output pwm4"
                default n
                if BSP_USING_PWM4
                    config BSP_USING_PWM4_CH0
                        bool "Enable PWM4 channel0"
                        default n

                    config BSP_USING_PWM4_CH1
                        bool "Enable PWM4 channel1"
                        default n
                endif
        endif

    menuconfig BSP_USING_I2C
        bool "Enable I2C"
        select RT_USING_I2C
        default n
        if BSP_USING_I2C
            config BSP_USING_I2C1
                bool "Enable I2C1"
                default n
            choice
                prompt "Select I2C1 badurate"
                default HW_I2C1_BADURATE_100kHZ

                config HW_I2C1_BADURATE_100kHZ
                    bool "Badurate 100kHZ"

                config HW_I2C1_BADURATE_400kHZ
                    bool "Badurate 400kHZ"
            endchoice
        endif

    menuconfig BSP_USING_ADC
        bool "Enable ADC"
        default n
        select RT_USING_ADC
        if BSP_USING_ADC
            config BSP_USING_ADC1
                bool "Enable ADC1"
                default n
        endif
    config BSP_USING_RTC
        bool "Enable RTC"
        select RT_USING_RTC
        default n
	config BSP_USING_CACHE
        bool "Enable CACHE"
        default n	

endmenu

menu "Onboard Peripheral Drivers"
    config BSP_USING_RGB
            bool "Enable RGB LED (PWM1_CH3A, PWM4_CH0A and PWM4_CH1A)"
            select BSP_USING_PWM1
            select BSP_USING_PWM4
            select BSP_USING_PWM1_CH3
            select BSP_USING_PWM4_CH0
            select BSP_USING_PWM4_CH1
            default n

        config BSP_USING_MPU6050
            bool "Enable MPU6050 (I2C1:J11 --> SCL; K11 --> SDA)"
            select BSP_USING_I2C1
            select PKG_USING_MPU6XXX
            default n

        menuconfig BSP_USING_AP3216C
            bool "Enable AP3216C (I2C1:J11 --> SCL; K11 --> SDA)"
            select BSP_USING_I2C1
            select PKG_USING_AP3216C
            default n
            if BSP_USING_AP3216C
                config AP3216C_USING_HW_INT
                bool "Enable interrupt"
                default n
            endif

        config BSP_USING_EEPROM
            bool "Enable I2C EEPROM (I2C1:J11 --> SCL; K11 --> SDA)"
            select BSP_USING_I2C1
            select  PKG_USING_AT24CXX
            default n

        config BSP_USING_RS232
            bool "Enable RS232"
            select BSP_USING_LPUART2
            default n

        config BSP_USING_RS485
            bool "Enable RS485"
            select BSP_USING_LPUART5
            default n
	menuconfig BSP_USING_ETH
        bool "Enable Ethernet"
        select RT_USING_NETDEV
        select RT_USING_LWIP
        default n

    if BSP_USING_ETH
        config BSP_USING_PHY
            select RT_USING_PHY
            bool "Enable ethernet phy"
            default y

        if BSP_USING_PHY
            config PHY_USING_KSZ8081
                bool "i.MX RT1020EVK uses ksz8081 phy"
                default y

            if PHY_USING_KSZ8081
                config PHY_KSZ8081_ADDRESS
                int "Specify address of phy device"
                default 2

                config PHY_RESET_KSZ8081_PORT
                    int "indicate port of reset"
                    default 1

                config PHY_RESET_KSZ8081_PIN
                    int "indicate pin of reset"
                    default 4

                config FSL_FEATURE_PHYKSZ8081_USE_RMII50M_MODE
                    bool "Enable the PHY ksz8081 RMII50M mode"
                    depends on PHY_USING_KSZ8081
                    default y
            endif
        endif
    endif					

endmenu

menu "Board extended module Drivers"

endmenu

endmenu