rt-thread/bsp/stm32/stm32f407-atk-explorer/board/Kconfig

472 lines
12 KiB
Plaintext
Raw Normal View History

menu "Hardware Drivers Config"
config SOC_STM32F407ZG
bool
select SOC_SERIES_STM32F4
select RT_USING_COMPONENTS_INIT
select RT_USING_USER_MAIN
default y
2022-02-27 09:02:14 +08:00
config BOARD_STM32F407_ATK_EXPLORER
bool
default y
menu "Onboard Peripheral Drivers"
config BSP_USING_USB_TO_USART
bool "Enable USB TO USART (uart1)"
2019-01-08 12:04:44 +08:00
select BSP_USING_UART
select BSP_USING_UART1
default y
2018-12-26 10:37:50 +08:00
config BSP_USING_COM2
bool "Enable COM2 (uart2 pin conflict with Ethernet and PWM)"
depends on (!BSP_USING_ETH && !BSP_USING_PWM)
2019-01-08 12:04:44 +08:00
select BSP_USING_UART
2018-12-26 10:37:50 +08:00
select BSP_USING_UART2
default n
config BSP_USING_COM3
bool "Enable COM3 (uart3)"
2019-01-08 12:04:44 +08:00
select BSP_USING_UART
select BSP_USING_UART3
default n
2020-02-23 11:37:24 +08:00
config BSP_USING_SRAM
bool "Enable SRAM"
select BSP_USING_EXT_FMC_IO
select BSP_USING_FMC
default n
config BSP_USING_MCU_LCD
bool "Enable ATK LCD"
select BSP_USING_SRAM
default n
if BSP_USING_MCU_LCD
config BSP_USING_MCU_LCD_TEST
bool "Enable lcd fill test"
default y
endif
config BSP_USING_TOUCH
bool "Use LCD TOUCH"
select BSP_USING_I2C2
default n
if BSP_USING_TOUCH
config BSP_TOUCH_INT_PIN
int "Touch interrupt pin, PB1"
default 17
endif
config BSP_USING_LVGL
bool "Enable LVGL for LCD"
select BSP_USING_MCU_LCD
select BSP_USING_TOUCH
select PKG_USING_LVGL
default n
2018-12-26 10:37:50 +08:00
config BSP_USING_SPI_FLASH
bool "Enable SPI FLASH (W25Q128 spi1)"
2019-01-08 12:04:44 +08:00
select BSP_USING_SPI
2018-12-26 10:37:50 +08:00
select BSP_USING_SPI1
select RT_USING_SFUD
select RT_SFUD_USING_SFDP
default n
config BSP_USING_EEPROM
bool "Enable I2C EEPROM (i2c1)"
select BSP_USING_I2C1
default n
config BSP_USING_ETH
bool "Enable Ethernet"
default n
select RT_USING_LWIP
select RT_LWIP_USING_HW_CHECKSUM
2021-05-10 14:22:06 +08:00
config BSP_USING_ETH_SAL
bool "Enable Ethernet with SAL"
depends on BSP_USING_ETH
default y
select RT_USING_SAL
select SAL_USING_POSIX
2021-05-11 09:15:10 +08:00
config PHY_USING_LAN8720A
bool
depends on BSP_USING_ETH
default y
config BSP_USING_MPU6050
bool "Enable MPU6050 (i2c1)"
default n
select BSP_USING_I2C1
select PKG_USING_MPU6XXX
menu "Enable File System"
config BSP_USING_FS
bool
default n
config BSP_USING_SDCARD_FATFS
bool "Enable SDCARD (FATFS)"
select BSP_USING_SDIO
select RT_USING_DFS
select RT_USING_DFS_ELMFAT
select RT_USING_DFS_ROMFS
select BSP_USING_FS
default n
config SDIO_MAX_FREQ
int "sdio max freq"
range 0 24000000
depends on BSP_USING_SDCARD
default 1000000
config BSP_USING_SPI_FLASH_LITTLEFS
bool "Enable SPI-FLASH (LittleFS)"
select RT_USING_DFS
select RT_USING_DFS_ROMFS
select RT_USING_MTD_NOR
select BSP_USING_SPI_FLASH
select BSP_USING_FS
select PKG_USING_FAL
select FAL_USING_AUTO_INIT
select FAL_PART_HAS_TABLE_CFG
select PKG_USING_LITTLEFS
default n
endmenu
endmenu
menu "On-chip Peripheral Drivers"
config BSP_USING_GPIO
bool "Enable GPIO"
select RT_USING_PIN
default y
2019-01-08 12:04:44 +08:00
menuconfig BSP_USING_UART
bool "Enable UART"
default y
select RT_USING_SERIAL
2019-01-08 12:04:44 +08:00
if BSP_USING_UART
config BSP_USING_UART1
bool "Enable UART1"
default y
config BSP_UART1_RX_USING_DMA
bool "Enable UART1 RX DMA"
depends on BSP_USING_UART1 && RT_SERIAL_USING_DMA
default n
2019-01-08 12:04:44 +08:00
2019-05-03 20:52:31 +08:00
config BSP_UART1_TX_USING_DMA
bool "Enable UART1 TX DMA"
depends on BSP_USING_UART1 && RT_SERIAL_USING_DMA
default n
config BSP_USING_UART2
bool "Enable UART2"
default n
config BSP_UART2_RX_USING_DMA
bool "Enable UART2 RX DMA"
depends on BSP_USING_UART2 && RT_SERIAL_USING_DMA
default n
config BSP_UART2_TX_USING_DMA
bool "Enable UART2 TX DMA"
depends on BSP_USING_UART2 && RT_SERIAL_USING_DMA
default n
2019-01-08 12:04:44 +08:00
config BSP_USING_UART3
bool "Enable UART3"
default n
config BSP_UART3_RX_USING_DMA
bool "Enable UART3 RX DMA"
depends on BSP_USING_UART3 && RT_SERIAL_USING_DMA
default n
2019-05-03 20:52:31 +08:00
config BSP_UART3_TX_USING_DMA
bool "Enable UART3 TX DMA"
depends on BSP_USING_UART3 && RT_SERIAL_USING_DMA
default n
2019-05-03 20:52:31 +08:00
config BSP_USING_UART4
bool "Enable UART4"
default n
config BSP_UART4_RX_USING_DMA
bool "Enable UART4 RX DMA"
depends on BSP_USING_UART4 && RT_SERIAL_USING_DMA
default n
2019-05-03 20:52:31 +08:00
config BSP_UART4_TX_USING_DMA
bool "Enable UART4 TX DMA"
depends on BSP_USING_UART4 && RT_SERIAL_USING_DMA
default n
2019-05-03 20:52:31 +08:00
config BSP_USING_UART5
bool "Enable UART5"
default n
config BSP_UART5_RX_USING_DMA
bool "Enable UART5 RX DMA"
depends on BSP_USING_UART5 && RT_SERIAL_USING_DMA
default n
2019-05-03 20:52:31 +08:00
config BSP_UART5_TX_USING_DMA
bool "Enable UART5 TX DMA"
depends on BSP_USING_UART5 && RT_SERIAL_USING_DMA
default n
2019-05-03 20:52:31 +08:00
config BSP_USING_UART6
bool "Enable UART6"
default n
config BSP_UART6_RX_USING_DMA
bool "Enable UART6 RX DMA"
depends on BSP_USING_UART6 && RT_SERIAL_USING_DMA
default n
2019-05-03 20:52:31 +08:00
config BSP_UART6_TX_USING_DMA
bool "Enable UART6 TX DMA"
depends on BSP_USING_UART6 && RT_SERIAL_USING_DMA
2019-01-08 12:04:44 +08:00
default n
endif
menuconfig BSP_USING_TIM
bool "Enable timer"
default n
select RT_USING_HWTIMER
if BSP_USING_TIM
config BSP_USING_TIM11
bool "Enable TIM11"
default n
config BSP_USING_TIM13
bool "Enable TIM13"
default n
config BSP_USING_TIM14
bool "Enable TIM14"
default n
endif
menuconfig BSP_USING_PWM
bool "Enable pwm"
default n
select RT_USING_PWM
if BSP_USING_PWM
menuconfig BSP_USING_PWM2
bool "Enable timer2 output pwm"
default n
if BSP_USING_PWM2
config BSP_USING_PWM2_CH4
bool "Enable PWM2 channel4"
default n
endif
endif
config BSP_USING_ON_CHIP_FLASH
bool "Enable on-chip FLASH"
default n
2019-01-08 12:04:44 +08:00
menuconfig BSP_USING_SPI
bool "Enable SPI BUS"
default n
select RT_USING_SPI
2019-01-08 12:04:44 +08:00
if BSP_USING_SPI
config BSP_USING_SPI1
bool "Enable SPI1 BUS"
default n
2019-01-08 12:04:44 +08:00
config BSP_SPI1_TX_USING_DMA
bool "Enable SPI1 TX DMA"
depends on BSP_USING_SPI1
default n
2019-01-08 12:04:44 +08:00
config BSP_SPI1_RX_USING_DMA
bool "Enable SPI1 RX DMA"
depends on BSP_USING_SPI1
select BSP_SPI1_TX_USING_DMA
default n
2019-01-08 12:04:44 +08:00
config BSP_USING_SPI2
bool "Enable SPI2 BUS"
default n
config BSP_SPI2_TX_USING_DMA
bool "Enable SPI2 TX DMA"
depends on BSP_USING_SPI2
default n
2019-01-08 12:04:44 +08:00
config BSP_SPI2_RX_USING_DMA
bool "Enable SPI2 RX DMA"
depends on BSP_USING_SPI2
select BSP_SPI2_TX_USING_DMA
default n
endif
menuconfig BSP_USING_ADC
bool "Enable ADC"
default n
select RT_USING_ADC
if BSP_USING_ADC
config BSP_USING_ADC1
bool "Enable ADC1"
default n
endif
menuconfig BSP_USING_I2C1
bool "Enable I2C1 BUS (software simulation)"
default y
select RT_USING_I2C
select RT_USING_I2C_BITOPS
select RT_USING_PIN
if BSP_USING_I2C1
config BSP_I2C1_SCL_PIN
int "i2c1 scl pin number"
range 0 143
default 24
config BSP_I2C1_SDA_PIN
int "I2C1 sda pin number"
range 0 143
default 25
endif
menuconfig BSP_USING_I2C2
bool "Enable LCD Touch BUS (software simulation)"
default y
select RT_USING_I2C
select RT_USING_I2C_BITOPS
select RT_USING_PIN
if BSP_USING_I2C2
config BSP_I2C2_SCL_PIN
int "i2c2 scl pin number, PB0"
range 0 143
default 16
config BSP_I2C2_SDA_PIN
int "I2C2 sda pin number, PF11"
range 0 143
default 91
endif
2020-12-15 17:58:12 +08:00
menuconfig BSP_USING_DAC
bool "Enable DAC"
default n
select RT_USING_DAC
if BSP_USING_DAC
config BSP_USING_DAC1
bool "Enable DAC1"
default n
endif
2019-03-19 18:21:51 +08:00
menuconfig BSP_USING_ONCHIP_RTC
bool "Enable RTC"
select RT_USING_RTC
default n
2019-03-19 18:21:51 +08:00
if BSP_USING_ONCHIP_RTC
choice
prompt "Select clock source"
default BSP_RTC_USING_LSE
config BSP_RTC_USING_LSE
bool "RTC USING LSE"
config BSP_RTC_USING_LSI
bool "RTC USING LSI"
endchoice
endif
config BSP_USING_WDT
bool "Enable Watchdog Timer"
select RT_USING_WDT
default n
config BSP_USING_SDIO
bool "Enable SDIO"
select RT_USING_SDIO
select RT_USING_DFS
default n
config BSP_USING_USBD
bool "Enable USB Device"
select RT_USING_USB_DEVICE
default n
menuconfig BSP_USING_USBH
bool "Enable USB Host"
select RT_USING_USB_HOST
default n
if BSP_USING_USBH
menuconfig RT_USBH_MSTORAGE
bool "Enable Udisk Drivers"
default n
if RT_USBH_MSTORAGE
config UDISK_MOUNTPOINT
string "Udisk mount dir"
default "/"
endif
endif
menuconfig BSP_USING_PULSE_ENCODER
bool "Enable Pulse Encoder"
default n
select RT_USING_PULSE_ENCODER
if BSP_USING_PULSE_ENCODER
config BSP_USING_PULSE_ENCODER4
bool "Enable Pulse Encoder4"
default n
endif
2020-02-23 11:37:24 +08:00
config BSP_USING_EXT_FMC_IO
bool
default n
2020-02-23 11:37:24 +08:00
config BSP_USING_FMC
bool
default n
source "../libraries/HAL_Drivers/Kconfig"
endmenu
menu "Board extended module Drivers"
menuconfig BSP_USING_AT_ESP8266
bool "Enable ESP8266(AT Command, COM3)"
default n
select BSP_USING_COM3
select PKG_USING_AT_DEVICE
select AT_DEVICE_USING_ESP8266
select AT_DEVICE_ESP8266_SAMPLE
select AT_DEVICE_ESP8266_SAMPLE_BSP_TAKEOVER
if BSP_USING_AT_ESP8266
config ESP8266_SAMPLE_WIFI_SSID
string "WIFI ssid"
default "rtthread"
config ESP8266_SAMPLE_WIFI_PASSWORD
string "WIFI password"
default "12345678"
config ESP8266_SAMPLE_CLIENT_NAME
string "AT client device name (Must be 'uart3')"
default "uart3"
config ESP8266_SAMPLE_RECV_BUFF_LEN
int "The maximum length of receive line buffer"
default 512
comment "May adjust RT_SERIAL_RB_BUFSZ up to 512 if using the Serial V1 device driver"
endif
endmenu
endmenu