rt-thread-official/bsp/stm32/stm32h743-atk-apollo/board/Kconfig

210 lines
5.1 KiB
Plaintext

menu "Hardware Drivers Config"
config SOC_STM32H743II
bool
select SOC_SERIES_STM32H7
select RT_USING_COMPONENTS_INIT
select RT_USING_USER_MAIN
default y
menu "Onboard Peripheral Drivers"
config BSP_USING_COM2
bool "Enable COM2(485)"
select BSP_USING_UART
select BSP_USING_UART2
select BSP_USING_I2C1
select PKG_USING_PCF8574
default n
config BSP_USING_SDRAM
bool "Enable SDRAM"
select BSP_USING_FMC
default n
config BSP_USING_LCD
bool "Enable LCD"
select BSP_USING_LTDC
select BSP_USING_SDRAM
default n
config BSP_USING_QSPI_FLASH
bool "Enable QSPI FLASH (W25Q256 qspi)"
select BSP_USING_QSPI
select RT_USING_SFUD
select RT_SFUD_USING_QSPI
default n
config BSP_USING_SDMMC
bool "Enable SDMMC (SD card)"
select RT_USING_SDIO
select RT_USING_DFS
select RT_USING_DFS_ELMFAT
default n
config BSP_USING_OV2640
bool "Enable camera (ov2640)"
select BSP_USING_DCMI
select BSP_USING_I2C
select BSP_USING_I2C2
default n
endmenu
menu "On-chip Peripheral Drivers"
config BSP_USING_GPIO
bool "Enable GPIO"
select RT_USING_PIN
default y
menuconfig BSP_USING_UART
bool "Enable UART"
default y
select RT_USING_SERIAL
if BSP_USING_UART
config BSP_USING_UART1
bool "Enable UART1"
default y
config BSP_USING_UART2
bool "Enable UART2"
default n
config BSP_UART2_RX_USING_DMA
bool "Enable UART2 RX DMA"
depends on BSP_USING_UART2 && RT_SERIAL_USING_DMA
default n
config BSP_UART2_TX_USING_DMA
bool "Enable UART2 TX DMA"
depends on BSP_USING_UART2 && RT_SERIAL_USING_DMA
default n
endif
config BSP_USING_FMC
bool
default n
config BSP_USING_LTDC
bool
default n
menuconfig BSP_USING_SPI
bool "Enable SPI BUS"
default n
select RT_USING_SPI
if BSP_USING_SPI
config BSP_USING_SPI2
bool "Enable SPI2 BUS"
default n
endif
config BSP_USING_QSPI
bool "Enable QSPI BUS"
select RT_USING_QSPI
select RT_USING_SPI
default n
menuconfig BSP_USING_I2C
bool "Enable I2C BUS (software simulation)"
select RT_USING_I2C
select RT_USING_I2C_BITOPS
select RT_USING_PIN
default n
if BSP_USING_I2C
menuconfig BSP_USING_I2C1
bool "Enable I2C1 BUS (software simulation)"
default n
if BSP_USING_I2C1
comment "Notice: PH4 --> 116; PH5 --> 117"
config BSP_I2C1_SCL_PIN
int "i2c1 scl pin number"
range 1 176
default 116
config BSP_I2C1_SDA_PIN
int "I2C1 sda pin number"
range 1 176
default 117
menuconfig BSP_USING_I2C2
bool "Enable I2C2 BUS (software simulation)"
default n
endif
menuconfig BSP_USING_I2C2
bool "Enable I2C2 BUS (software simulation)"
default n
if BSP_USING_I2C2
comment "Notice: PH13 --> 125; PH15 --> 127"
config BSP_I2C2_SCL_PIN
int "i2c2 scl pin number"
range 1 176
default 127
config BSP_I2C2_SDA_PIN
int "I2C2 sda pin number"
range 1 176
default 125
endif
endif
config BSP_USING_ON_CHIP_FLASH
bool "Enable on-chip FLASH"
default n
config BSP_USING_DCMI
bool "Enable DCMI"
default n
menuconfig BSP_USING_ONCHIP_RTC
bool "Enable RTC"
select RT_USING_RTC
select RT_USING_LIBC
default n
if BSP_USING_ONCHIP_RTC
choice
prompt "Select clock source"
default BSP_RTC_USING_LSE
config BSP_RTC_USING_LSE
bool "RTC USING LSE"
config BSP_RTC_USING_LSI
bool "RTC USING LSI"
endchoice
endif
menuconfig BSP_USING_ADC
bool "Enable ADC"
default n
select RT_USING_ADC
if BSP_USING_ADC
config BSP_USING_ADC1
bool "Enable ADC1"
default n
endif
menuconfig BSP_USING_DAC
bool "Enable DAC"
default n
select RT_USING_DAC
if BSP_USING_DAC
config BSP_USING_DAC1
bool "Enable DAC1"
default n
endif
config BSP_USING_WDT
bool "Enable Watchdog Timer"
select RT_USING_WDT
default n
source "../libraries/HAL_Drivers/Kconfig"
endmenu
menu "Board extended module Drivers"
endmenu
endmenu