rt-thread-official/bsp/stm32/stm32f103-atk-warshipv3/board/Kconfig

244 lines
6.2 KiB
Plaintext

menu "Hardware Drivers Config"
config SOC_STM32F103ZE
bool
select SOC_SERIES_STM32F1
select RT_USING_COMPONENTS_INIT
select RT_USING_USER_MAIN
default y
menu "Onboard Peripheral Drivers"
config BSP_USING_USB_TO_USART
bool "Enable USB TO USART (uart1)"
select BSP_USING_UART
select BSP_USING_UART1
default y
config BSP_USING_EEPROM
bool "Enable I2C EEPROM (i2c1)"
select BSP_USING_I2C1
default n
config BSP_USING_SPI_FLASH
bool "Enable SPI FLASH (W25Q16 spi2)"
select BSP_USING_SPI
select BSP_USING_SPI2
select RT_USING_SFUD
select RT_SFUD_USING_SFDP
default n
config BSP_USING_POT
bool "Enable potentiometer"
select BSP_USING_ADC
select BSP_USING_ADC1
default n
config BSP_USING_EXT_SRAM
bool "Enable external sram"
default n
help
Chip name is IS62WV51216, 1Mbytes static RAMs organized as 512K words by 16bits.
config BSP_USING_SDCARD
bool "Enable SDCARD (sdio)"
select BSP_USING_SDIO
select RT_USING_DFS
select RT_USING_DFS_ELMFAT
default n
endmenu
menu "On-chip Peripheral Drivers"
config BSP_USING_GPIO
bool "Enable GPIO"
select RT_USING_PIN
default y
menuconfig BSP_USING_UART
bool "Enable UART"
default y
select RT_USING_SERIAL
if BSP_USING_UART
config BSP_USING_UART1
bool "Enable UART1"
default y
config BSP_UART1_RX_USING_DMA
bool "Enable UART1 RX DMA"
depends on BSP_USING_UART1 && RT_SERIAL_USING_DMA
default n
config BSP_USING_UART2
bool "Enable UART2"
default n
config BSP_UART2_RX_USING_DMA
bool "Enable UART2 RX DMA"
depends on BSP_USING_UART2 && RT_SERIAL_USING_DMA
default n
config BSP_USING_UART3
bool "Enable UART3"
default n
config BSP_UART3_RX_USING_DMA
bool "Enable UART3 RX DMA"
depends on BSP_USING_UART3 && RT_SERIAL_USING_DMA
default n
endif
menuconfig BSP_USING_TIM
bool "Enable timer"
default n
select RT_USING_HWTIMER
if BSP_USING_TIM
config BSP_USING_TIM2
bool "Enable TIM2"
default n
config BSP_USING_TIM3
bool "Enable TIM3"
default n
config BSP_USING_TIM4
bool "Enable TIM4"
default n
endif
menuconfig BSP_USING_PWM
bool "Enable pwm"
default n
select RT_USING_PWM
if BSP_USING_PWM
menuconfig BSP_USING_PWM3
bool "Enable timer3 output pwm"
default n
if BSP_USING_PWM3
config BSP_USING_PWM3_CH1
bool "Enable PWM3 channel1"
default n
config BSP_USING_PWM3_CH2
bool "Enable PWM3 channel2"
default n
endif
endif
menuconfig BSP_USING_SPI
bool "Enable SPI BUS"
default n
select RT_USING_SPI
if BSP_USING_SPI
config BSP_USING_SPI1
bool "Enable SPI1 BUS"
default n
config BSP_SPI1_TX_USING_DMA
bool "Enable SPI1 TX DMA"
depends on BSP_USING_SPI1
default n
config BSP_SPI1_RX_USING_DMA
bool "Enable SPI1 RX DMA"
depends on BSP_USING_SPI1
select BSP_SPI1_TX_USING_DMA
default n
config BSP_USING_SPI2
bool "Enable SPI2 BUS"
default n
config BSP_SPI2_TX_USING_DMA
bool "Enable SPI2 TX DMA"
depends on BSP_USING_SPI2
default n
config BSP_SPI2_RX_USING_DMA
bool "Enable SPI2 RX DMA"
depends on BSP_USING_SPI2
select BSP_SPI2_TX_USING_DMA
default n
endif
menuconfig BSP_USING_I2C1
bool "Enable I2C1 BUS (software simulation)"
default n
select RT_USING_I2C
select RT_USING_I2C_BITOPS
select RT_USING_PIN
if BSP_USING_I2C1
config BSP_I2C1_SCL_PIN
int "i2c1 scl pin number"
range 0 63
default 22
config BSP_I2C1_SDA_PIN
int "I2C1 sda pin number"
range 0 63
default 23
endif
menuconfig BSP_USING_ADC
bool "Enable ADC"
default n
select RT_USING_ADC
if BSP_USING_ADC
config BSP_USING_ADC1
bool "Enable ADC1"
default n
endif
config BSP_USING_ON_CHIP_FLASH
bool "Enable on-chip FLASH"
default n
menuconfig BSP_USING_ONCHIP_RTC
bool "Enable RTC"
select RT_USING_RTC
select RT_USING_LIBC
default n
if BSP_USING_ONCHIP_RTC
choice
prompt "Select clock source"
default BSP_RTC_USING_LSE
config BSP_RTC_USING_LSE
bool "RTC USING LSE"
config BSP_RTC_USING_LSI
bool "RTC USING LSI"
endchoice
endif
config BSP_USING_WDT
bool "Enable Watchdog Timer"
select RT_USING_WDT
default n
config BSP_USING_SDIO
bool "Enable SDIO"
select RT_USING_SDIO
default n
menuconfig BSP_USING_PULSE_ENCODER
bool "Enable Pulse Encoder"
default n
select RT_USING_PULSE_ENCODER
if BSP_USING_PULSE_ENCODER
config BSP_USING_PULSE_ENCODER3
bool "Enable Pulse Encoder3"
default n
endif
source "../libraries/HAL_Drivers/Kconfig"
endmenu
menu "Board extended module Drivers"
endmenu
endmenu