rt-thread-official/bsp/gd32450z-eval/drivers/drv_exmc_sdram.c

316 lines
14 KiB
C

/*!
\file main.c
\brief exmc sdram(MICRON 48LC16M16A2) driver
*/
/*
Copyright (C) 2016 GigaDevice
2016-10-19, V1.0.0, demo for GD32F4xx
*/
#include "gd32f4xx.h"
#include "drv_exmc_sdram.h"
#include <rtthread.h>
/* define mode register content */
/* burst length */
#define SDRAM_MODEREG_BURST_LENGTH_1 ((uint16_t)0x0000)
#define SDRAM_MODEREG_BURST_LENGTH_2 ((uint16_t)0x0001)
#define SDRAM_MODEREG_BURST_LENGTH_4 ((uint16_t)0x0002)
#define SDRAM_MODEREG_BURST_LENGTH_8 ((uint16_t)0x0003)
/* burst type */
#define SDRAM_MODEREG_BURST_TYPE_SEQUENTIAL ((uint16_t)0x0000)
#define SDRAM_MODEREG_BURST_TYPE_INTERLEAVED ((uint16_t)0x0008)
/* CAS latency */
#define SDRAM_MODEREG_CAS_LATENCY_2 ((uint16_t)0x0020)
#define SDRAM_MODEREG_CAS_LATENCY_3 ((uint16_t)0x0030)
/* write mode */
#define SDRAM_MODEREG_WRITEBURST_MODE_PROGRAMMED ((uint16_t)0x0000)
#define SDRAM_MODEREG_WRITEBURST_MODE_SINGLE ((uint16_t)0x0200)
#define SDRAM_MODEREG_OPERATING_MODE_STANDARD ((uint16_t)0x0000)
#define SDRAM_TIMEOUT ((uint32_t)0x0000FFFF)
static void delay_1ms(volatile uint32_t count)
{
count *= 1000;
while (count--)
{
count = count;
}
}
/*!
\brief sdram peripheral initialize
\param[in] sdram_device: specifie the SDRAM device
\param[out] none
\retval none
*/
void exmc_synchronous_dynamic_ram_init(uint32_t sdram_device)
{
exmc_sdram_parameter_struct sdram_init_struct;
exmc_sdram_timing_parameter_struct sdram_timing_init_struct;
exmc_sdram_command_parameter_struct sdram_command_init_struct;
uint32_t command_content = 0, bank_select;
uint32_t timeout = SDRAM_TIMEOUT;
/* enable EXMC clock*/
rcu_periph_clock_enable(RCU_EXMC);
rcu_periph_clock_enable(RCU_GPIOB);
rcu_periph_clock_enable(RCU_GPIOC);
rcu_periph_clock_enable(RCU_GPIOD);
rcu_periph_clock_enable(RCU_GPIOE);
rcu_periph_clock_enable(RCU_GPIOF);
rcu_periph_clock_enable(RCU_GPIOG);
rcu_periph_clock_enable(RCU_GPIOH);
/* common GPIO configuration */
/* SDNWE(PC0),SDNE0(PC2),SDCKE0(PC3) pin configuration */
gpio_af_set(GPIOC, GPIO_AF_12, GPIO_PIN_0 | GPIO_PIN_2 | GPIO_PIN_3);
gpio_mode_set(GPIOC, GPIO_MODE_AF, GPIO_PUPD_PULLUP, GPIO_PIN_0 | GPIO_PIN_2 | GPIO_PIN_3);
gpio_output_options_set(GPIOC, GPIO_OTYPE_PP, GPIO_OSPEED_50MHZ, GPIO_PIN_0 | GPIO_PIN_2 | GPIO_PIN_3);
/* D2(PD0),D3(PD1),D13(PD8),D14(PD9),D15(PD10),D0(PD14),D1(PD15) pin configuration */
gpio_af_set(GPIOD, GPIO_AF_12, GPIO_PIN_0 | GPIO_PIN_1 | GPIO_PIN_8 | GPIO_PIN_9 |
GPIO_PIN_10 | GPIO_PIN_14 | GPIO_PIN_15);
gpio_mode_set(GPIOD, GPIO_MODE_AF, GPIO_PUPD_PULLUP, GPIO_PIN_0 | GPIO_PIN_1 | GPIO_PIN_8 | GPIO_PIN_9 |
GPIO_PIN_10 | GPIO_PIN_14 | GPIO_PIN_15);
gpio_output_options_set(GPIOD, GPIO_OTYPE_PP, GPIO_OSPEED_50MHZ, GPIO_PIN_0 | GPIO_PIN_1 | GPIO_PIN_8 | GPIO_PIN_9 |
GPIO_PIN_10 | GPIO_PIN_14 | GPIO_PIN_15);
/* NBL0(PE0),NBL1(PE1),D4(PE7),D5(PE8),D6(PE9),D7(PE10),D8(PE11),D9(PE12),D10(PE13),D11(PE14),D12(PE15) pin configuration */
gpio_af_set(GPIOE, GPIO_AF_12, GPIO_PIN_0 | GPIO_PIN_1 | GPIO_PIN_7 | GPIO_PIN_8 |
GPIO_PIN_9 | GPIO_PIN_10 | GPIO_PIN_11 | GPIO_PIN_12 |
GPIO_PIN_13 | GPIO_PIN_14 | GPIO_PIN_15);
gpio_mode_set(GPIOE, GPIO_MODE_AF, GPIO_PUPD_PULLUP, GPIO_PIN_0 | GPIO_PIN_1 | GPIO_PIN_7 | GPIO_PIN_8 |
GPIO_PIN_9 | GPIO_PIN_10 | GPIO_PIN_11 | GPIO_PIN_12 |
GPIO_PIN_13 | GPIO_PIN_14 | GPIO_PIN_15);
gpio_output_options_set(GPIOE, GPIO_OTYPE_PP, GPIO_OSPEED_50MHZ, GPIO_PIN_0 | GPIO_PIN_1 | GPIO_PIN_7 | GPIO_PIN_8 |
GPIO_PIN_9 | GPIO_PIN_10 | GPIO_PIN_11 | GPIO_PIN_12 |
GPIO_PIN_13 | GPIO_PIN_14 | GPIO_PIN_15);
/* A0(PF0),A1(PF1),A2(PF2),A3(PF3),A4(PF4),A5(PF5),NRAS(PF11),A6(PF12),A7(PF13),A8(PF14),A9(PF15) pin configuration */
gpio_af_set(GPIOF, GPIO_AF_12, GPIO_PIN_0 | GPIO_PIN_1 | GPIO_PIN_2 | GPIO_PIN_3 |
GPIO_PIN_4 | GPIO_PIN_5 | GPIO_PIN_11 | GPIO_PIN_12 |
GPIO_PIN_13 | GPIO_PIN_14 | GPIO_PIN_15);
gpio_mode_set(GPIOF, GPIO_MODE_AF, GPIO_PUPD_PULLUP, GPIO_PIN_0 | GPIO_PIN_1 | GPIO_PIN_2 | GPIO_PIN_3 |
GPIO_PIN_4 | GPIO_PIN_5 | GPIO_PIN_11 | GPIO_PIN_12 |
GPIO_PIN_13 | GPIO_PIN_14 | GPIO_PIN_15);
gpio_output_options_set(GPIOF, GPIO_OTYPE_PP, GPIO_OSPEED_50MHZ, GPIO_PIN_0 | GPIO_PIN_1 | GPIO_PIN_2 | GPIO_PIN_3 |
GPIO_PIN_4 | GPIO_PIN_5 | GPIO_PIN_11 | GPIO_PIN_12 |
GPIO_PIN_13 | GPIO_PIN_14 | GPIO_PIN_15);
/* A10(PG0),A11(PG1),A12(PG2),A14(PG4),A15(PG5),SDCLK(PG8),NCAS(PG15) pin configuration */
gpio_af_set(GPIOG, GPIO_AF_12, GPIO_PIN_0 | GPIO_PIN_1 | GPIO_PIN_2 | GPIO_PIN_4 |
GPIO_PIN_5 | GPIO_PIN_8 | GPIO_PIN_15);
gpio_mode_set(GPIOG, GPIO_MODE_AF, GPIO_PUPD_PULLUP, GPIO_PIN_0 | GPIO_PIN_1 | GPIO_PIN_2 | GPIO_PIN_4 |
GPIO_PIN_5 | GPIO_PIN_8 | GPIO_PIN_15);
gpio_output_options_set(GPIOG, GPIO_OTYPE_PP, GPIO_OSPEED_50MHZ, GPIO_PIN_0 | GPIO_PIN_1 | GPIO_PIN_2 | GPIO_PIN_4 |
GPIO_PIN_5 | GPIO_PIN_8 | GPIO_PIN_15);
/* specify which SDRAM to read and write */
if(EXMC_SDRAM_DEVICE0 == sdram_device){
bank_select = EXMC_SDRAM_DEVICE0_SELECT;
}else{
bank_select = EXMC_SDRAM_DEVICE1_SELECT;
}
/* EXMC SDRAM device initialization sequence --------------------------------*/
/* Step 1 : configure SDRAM timing registers --------------------------------*/
/* LMRD: 2 clock cycles */
sdram_timing_init_struct.load_mode_register_delay = 2;
/* XSRD: min = 67ns */
sdram_timing_init_struct.exit_selfrefresh_delay = 7;
/* RASD: min=42ns , max=120k (ns) */
sdram_timing_init_struct.row_address_select_delay = 5;
/* ARFD: min=60ns */
sdram_timing_init_struct.auto_refresh_delay = 6;
/* WRD: min=1 Clock cycles +6ns */
sdram_timing_init_struct.write_recovery_delay = 2;
/* RPD: min=18ns */
sdram_timing_init_struct.row_precharge_delay = 2;
/* RCD: min=18ns */
sdram_timing_init_struct.row_to_column_delay = 2;
/* step 2 : configure SDRAM control registers ---------------------------------*/
sdram_init_struct.sdram_device = sdram_device;
sdram_init_struct.column_address_width = EXMC_SDRAM_COW_ADDRESS_9;
sdram_init_struct.row_address_width = EXMC_SDRAM_ROW_ADDRESS_13;
sdram_init_struct.data_width = EXMC_SDRAM_DATABUS_WIDTH_16B;
sdram_init_struct.internal_bank_number = EXMC_SDRAM_4_INTER_BANK;
sdram_init_struct.cas_latency = EXMC_CAS_LATENCY_3_SDCLK;
sdram_init_struct.write_protection = DISABLE;
sdram_init_struct.sdclock_config = EXMC_SDCLK_PERIODS_2_HCLK;
sdram_init_struct.brust_read_switch = ENABLE;
sdram_init_struct.pipeline_read_delay = EXMC_PIPELINE_DELAY_1_HCLK;
sdram_init_struct.timing = &sdram_timing_init_struct;
/* EXMC SDRAM bank initialization */
exmc_sdram_init(&sdram_init_struct);
/* step 3 : configure CKE high command---------------------------------------*/
sdram_command_init_struct.command = EXMC_SDRAM_CLOCK_ENABLE;
sdram_command_init_struct.bank_select = bank_select;
sdram_command_init_struct.auto_refresh_number = EXMC_SDRAM_AUTO_REFLESH_1_SDCLK;
sdram_command_init_struct.mode_register_content = 0;
/* wait until the SDRAM controller is ready */
while((exmc_flag_get(sdram_device, EXMC_SDRAM_FLAG_NREADY) != RESET) && (timeout > 0)){
timeout--;
}
/* send the command */
exmc_sdram_command_config(&sdram_command_init_struct);
/* step 4 : insert 10ms delay----------------------------------------------*/
delay_1ms(10);
/* step 5 : configure precharge all command----------------------------------*/
sdram_command_init_struct.command = EXMC_SDRAM_PRECHARGE_ALL;
sdram_command_init_struct.bank_select = bank_select;
sdram_command_init_struct.auto_refresh_number = EXMC_SDRAM_AUTO_REFLESH_1_SDCLK;
sdram_command_init_struct.mode_register_content = 0;
/* wait until the SDRAM controller is ready */
timeout = SDRAM_TIMEOUT;
while((exmc_flag_get(sdram_device, EXMC_SDRAM_FLAG_NREADY) != RESET) && (timeout > 0)){
timeout--;
}
/* send the command */
exmc_sdram_command_config(&sdram_command_init_struct);
/* step 6 : configure Auto-Refresh command-----------------------------------*/
sdram_command_init_struct.command = EXMC_SDRAM_AUTO_REFRESH;
sdram_command_init_struct.bank_select = bank_select;
sdram_command_init_struct.auto_refresh_number = EXMC_SDRAM_AUTO_REFLESH_8_SDCLK;
sdram_command_init_struct.mode_register_content = 0;
/* wait until the SDRAM controller is ready */
timeout = SDRAM_TIMEOUT;
while((exmc_flag_get(sdram_device, EXMC_SDRAM_FLAG_NREADY) != RESET) && (timeout > 0)){
timeout--;
}
/* send the command */
exmc_sdram_command_config(&sdram_command_init_struct);
/* step 7 : configure load mode register command-----------------------------*/
/* program mode register */
command_content = (uint32_t)SDRAM_MODEREG_BURST_LENGTH_1 |
SDRAM_MODEREG_BURST_TYPE_SEQUENTIAL |
SDRAM_MODEREG_CAS_LATENCY_3 |
SDRAM_MODEREG_OPERATING_MODE_STANDARD |
SDRAM_MODEREG_WRITEBURST_MODE_SINGLE;
sdram_command_init_struct.command = EXMC_SDRAM_LOAD_MODE_REGISTER;
sdram_command_init_struct.bank_select = bank_select;
sdram_command_init_struct.auto_refresh_number = EXMC_SDRAM_AUTO_REFLESH_1_SDCLK;
sdram_command_init_struct.mode_register_content = command_content;
/* wait until the SDRAM controller is ready */
timeout = SDRAM_TIMEOUT;
while((exmc_flag_get(sdram_device, EXMC_SDRAM_FLAG_NREADY) != RESET) && (timeout > 0)){
timeout--;
}
/* send the command */
exmc_sdram_command_config(&sdram_command_init_struct);
/* step 8 : set the auto-refresh rate counter--------------------------------*/
/* 64ms, 8192-cycle refresh, 64ms/8192=7.81us */
/* SDCLK_Freq = SYS_Freq/2 */
/* (7.81 us * SDCLK_Freq) - 20 */
exmc_sdram_refresh_count_set(761);
/* wait until the SDRAM controller is ready */
timeout = SDRAM_TIMEOUT;
while((exmc_flag_get(sdram_device, EXMC_SDRAM_FLAG_NREADY) != RESET) && (timeout > 0)){
timeout--;
}
}
/*!
\brief fill the buffer with specified value
\param[in] pbuffer: pointer on the buffer to fill
\param[in] buffersize: size of the buffer to fill
\param[in] value: value to fill on the buffer
\param[out] none
\retval none
*/
void fill_buffer(uint8_t *pbuffer, uint16_t buffer_lengh, uint16_t offset)
{
uint16_t index = 0;
/* put in global buffer same values */
for (index = 0; index < buffer_lengh; index++ ){
pbuffer[index] = index + offset;
}
}
/*!
\brief write a byte buffer(data is 8 bits) to the EXMC SDRAM memory
\param[in] sdram_device: specify which a SDRAM memory block is written
\param[in] pbuffer: pointer to buffer
\param[in] writeaddr: SDRAM memory internal address from which the data will be written
\param[in] numbytetowrite: number of bytes to write
\param[out] none
\retval none
*/
void sdram_writebuffer_8(uint32_t sdram_device,uint8_t* pbuffer, uint32_t writeaddr, uint32_t numbytetowrite)
{
uint32_t temp_addr;
/* Select the base address according to EXMC_Bank */
if(sdram_device == EXMC_SDRAM_DEVICE0){
temp_addr = SDRAM_DEVICE0_ADDR;
}else{
temp_addr = SDRAM_DEVICE1_ADDR;
}
/* While there is data to write */
for(; numbytetowrite != 0; numbytetowrite--) {
/* Transfer data to the memory */
*(uint8_t *) (temp_addr + writeaddr) = *pbuffer++;
/* Increment the address*/
writeaddr += 1;
}
}
/*!
\brief read a block of 8-bit data from the EXMC SDRAM memory
\param[in] sdram_device: specify which a SDRAM memory block is written
\param[in] pbuffer: pointer to buffer
\param[in] readaddr: SDRAM memory internal address to read from
\param[in] numbytetoread: number of bytes to read
\param[out] none
\retval none
*/
void sdram_readbuffer_8(uint32_t sdram_device,uint8_t* pbuffer, uint32_t readaddr, uint32_t numbytetoread)
{
uint32_t temp_addr;
/* select the base address according to EXMC_Bank */
if(sdram_device == EXMC_SDRAM_DEVICE0){
temp_addr = SDRAM_DEVICE0_ADDR;
}else{
temp_addr = SDRAM_DEVICE1_ADDR;
}
/* while there is data to read */
for(; numbytetoread != 0; numbytetoread--){
/* read a byte from the memory */
*pbuffer++ = *(uint8_t*) (temp_addr + readaddr);
/* increment the address */
readaddr += 1;
}
}
int rt_hw_sdram_init(void)
{
exmc_synchronous_dynamic_ram_init(EXMC_SDRAM_DEVICE0);
return 0;
}
INIT_BOARD_EXPORT(rt_hw_sdram_init);