mirror of
https://github.com/RT-Thread/rt-thread.git
synced 2025-02-03 16:04:35 +08:00
814b1abb08
* Update Kconfig 增加RT1170双路网络选项 * Update SConscript 增加RTL8211F驱动选项支持 * Update SConstruct 去掉外设目录 * Add files via upload 增加PHY芯片RTL8211F驱动 * Update drv_rtl8211f.c * format code Co-authored-by: Meco Man <920369182@qq.com>
162 lines
4.5 KiB
Plaintext
162 lines
4.5 KiB
Plaintext
menu "Hardware Drivers Config"
|
|
|
|
config BSP_USING_QSPIFLASH
|
|
bool
|
|
default n
|
|
|
|
config SOC_MIMXRT1176DVMAA
|
|
bool
|
|
select SOC_MIMXRT1170_SERIES
|
|
select BSP_USING_QSPIFLASH
|
|
select RT_USING_COMPONENTS_INIT
|
|
select RT_USING_USER_MAIN
|
|
default y
|
|
|
|
menu "On-chip Peripheral Drivers"
|
|
|
|
config BSP_USING_DMA
|
|
bool "Enable DMA"
|
|
default n
|
|
|
|
config BSP_USING_GPIO
|
|
bool "Enable GPIO"
|
|
select RT_USING_PIN
|
|
default y
|
|
|
|
menuconfig BSP_USING_LPUART
|
|
bool "Enable UART"
|
|
select RT_USING_SERIAL
|
|
default y
|
|
|
|
if BSP_USING_LPUART
|
|
config BSP_USING_LPUART1
|
|
bool "Enable LPUART1"
|
|
default y
|
|
|
|
config BSP_LPUART1_RX_USING_DMA
|
|
bool "Enable LPUART1 RX DMA"
|
|
depends on BSP_USING_LPUART1
|
|
select BSP_USING_DMA
|
|
select RT_SERIAL_USING_DMA
|
|
default n
|
|
|
|
config BSP_LPUART1_RX_DMA_CHANNEL
|
|
depends on BSP_LPUART1_RX_USING_DMA
|
|
int "Set LPUART1 RX DMA channel (0-32)"
|
|
default 0
|
|
|
|
config BSP_LPUART1_TX_USING_DMA
|
|
bool "Enable LPUART1 TX DMA"
|
|
depends on BSP_USING_LPUART1
|
|
select BSP_USING_DMA
|
|
select RT_SERIAL_USING_DMA
|
|
default n
|
|
|
|
config BSP_LPUART1_TX_DMA_CHANNEL
|
|
depends on BSP_LPUART1_TX_USING_DMA
|
|
int "Set LPUART1 TX DMA channel (0-32)"
|
|
default 1
|
|
|
|
config BSP_USING_LPUART3
|
|
bool "Enable LPUART3"
|
|
default n
|
|
|
|
config BSP_LPUART3_RX_USING_DMA
|
|
bool "Enable LPUART3 RX DMA"
|
|
depends on BSP_USING_LPUART3
|
|
select BSP_USING_DMA
|
|
select RT_SERIAL_USING_DMA
|
|
default n
|
|
|
|
config BSP_LPUART3_RX_DMA_CHANNEL
|
|
depends on BSP_LPUART3_RX_USING_DMA
|
|
int "Set LPUART3 RX DMA channel (0-32)"
|
|
default 0
|
|
|
|
config BSP_LPUART3_TX_USING_DMA
|
|
bool "Enable LPUART3 TX DMA"
|
|
depends on BSP_USING_LPUART3
|
|
select BSP_USING_DMA
|
|
select RT_SERIAL_USING_DMA
|
|
default n
|
|
|
|
config BSP_LPUART3_TX_DMA_CHANNEL
|
|
depends on BSP_LPUART3_TX_USING_DMA
|
|
int "Set LPUART3 TX DMA channel (0-32)"
|
|
default 1
|
|
endif
|
|
endmenu
|
|
|
|
menu "Onboard Peripheral Drivers"
|
|
|
|
config BSP_USING_SDRAM
|
|
bool "Enable SDRAM"
|
|
default n
|
|
|
|
menuconfig BSP_USING_ETH
|
|
bool "Enable Ethernet"
|
|
select RT_USING_NETDEV
|
|
select RT_USING_LWIP
|
|
default n
|
|
|
|
|
|
if BSP_USING_ETH
|
|
config BSP_USING_PHY
|
|
select RT_USING_PHY
|
|
bool "Enable ethernet phy"
|
|
default y
|
|
|
|
if BSP_USING_PHY
|
|
config PHY_USING_KSZ8081
|
|
bool "i.MX RT1176EVK uses ksz8081 phy"
|
|
default y
|
|
|
|
if PHY_USING_KSZ8081
|
|
config PHY_KSZ8081_ADDRESS
|
|
int "Specify address of phy device"
|
|
default 2
|
|
|
|
config PHY_RESET_KSZ8081_PORT
|
|
int "indicate port of reset"
|
|
default 6
|
|
|
|
config PHY_RESET_KSZ8081_PIN
|
|
int "indicate pin of reset"
|
|
default 12
|
|
|
|
config FSL_FEATURE_PHYKSZ8081_USE_RMII50M_MODE
|
|
bool "Enable the PHY ksz8081 RMII50M mode"
|
|
depends on PHY_USING_KSZ8081
|
|
default y
|
|
endif
|
|
endif
|
|
|
|
if BSP_USING_PHY
|
|
config PHY_USING_RTL8211F
|
|
bool "i.MX RT1176EVK uses rtl8211f phy"
|
|
default y
|
|
|
|
if PHY_USING_RTL8211F
|
|
config PHY_RTL8211F_ADDRESS
|
|
int "Specify address of phy device"
|
|
default 1
|
|
|
|
config PHY_RESET_RTL8211F_PORT
|
|
int "indicate port of reset"
|
|
default 11
|
|
|
|
config PHY_RESET_RTL8211F_PIN
|
|
int "indicate pin of reset"
|
|
default 14
|
|
|
|
endif
|
|
endif
|
|
endif
|
|
endmenu
|
|
|
|
menu "Board extended module Drivers"
|
|
|
|
endmenu
|
|
|
|
endmenu
|