rt-thread-official/bsp/rv32m1_vega
Hornos Lee 4f1a50be24
[HUST CSE] fix: Fixed wrong download link of env in 20+ files. (#7296)
2023-04-18 09:18:56 -04:00
..
ri5cy [HUST CSE] Fix nullptr issue in bsp/rv32m1_vega/ri5cy/board/fsl_host.c (#7236) 2023-04-13 20:03:54 -04:00
rv32m1_sdk_riscv [libcpu][riscv]整合libcpu/riscv中的移植文件 提供一份公共代码于common (#6941) 2023-03-01 01:32:43 -05:00
README.md Update BSP README with EN Version. 2020-09-09 18:22:26 +08:00
README_zh.md [HUST CSE] fix: Fixed wrong download link of env in 20+ files. (#7296) 2023-04-18 09:18:56 -04:00

README.md

RISC-V RV32M1 VEGA Board BSP(Board Support Package) Execution Instruction

中文页 |

Introduction

RV32M1_VEGA board is a heterogeneous multi-core RISC-V 32 development board that contains two RISC-V 32-bit cores, as well as BLE peripherals.

Hardware Description
Chip Model RV32M1
CPU RV32IMC, with extensons for post-incrementing load and stores,
multiply-accumulate extensions, ALU extensions, hardware loops.
RV32IEMC
Main Frequency 48MHz or 72MHz
48MHz or 72MHz
On-chip SRAM 256kB + 128kB
On-chip Flash 1MB + 256kB

Compilation

The toolchain currently used for test is built from the standard GNU GCC 7.2.0 and newlib 2.5.0 and for the standard RV32IMC architecture, so the extension instructions of RV32M1 is not supported, note that the version of RT-Thread ENV used in this BSP is 1.0.

It's recommended to use the env tool to compile programs on Windows. Switch to the directory bsp/rv32m1_vega/ri5cy in the console and run the following command to compile this BSP:

scons

If successfully compiled, a new 'rtthread.elf' and 'rtthread.bin' file will be generated. rtthread.bin' needs to be burned to the device and run.

Burn and Execution

Please use JLink to connect to the JTAG interface of the RISC-V core on the RV32M1_VEGA board, and change the JLink driver to WinUSB mode. The JTAG interface is located next to the RV32M1 chip and the antenna seat, with a small 20pin JTAG interface.

Use a USB cable to connect to a USB port marked with SDA, then a serial device is recognized by PC, which can be opened with the configuration of 115200-N-8-1. The serial pins used by the device are: [PTC7/PTC8]

When the rtthread.bin image file is generated after being correctly compiled, you can use gdb to connect to openocd and burn it to flash with the load command.

For more information about how to use JTAG and how to use gdb to debug the RV32M1_VEGA development board, please refer to Development Environment Construction.

Running Results

When the compiling and burning are done correctly, press the reset button SW1 to reset the device, the startup message of RT-Thread can be observed via the serial port :

 \ | /
- RT -     Thread Operating System
 / | \     4.0.0 build Dec  5 2018
 2006 - 2018 Copyright by rt-thread team
File System initialized!
Hello RT-Thread!
msh />

Peripheral Condition

Drive Support Remark
UART Support UART0, RX(PTC7), TX(PTC8)
Support UART1, RX(PTA25), TX(PTA26)
clock Support
GPIO Support(The list may not complete, also you need to modify pinmux, clock according to the IO being used.)
MMC/SD Support

IO mapping in BSP

IO Number BSP Code Definition
PTA22 LED_BLUE
PTA23 LED_GREEN
PTA24 LED_RED
PTA24 LED_STS
PTA25 UART1_RX
PTA26 UART1_TX
PTE8 BTN_SW3
PTE9 BTN_SW4
PTE12 BTN_SW5
PTA0 BTN_SW2/BTN_NMI

References