rt-thread-official/bsp/raspberry-pi/raspi4-32/driver/drv_uart.c

374 lines
9.5 KiB
C

/*
* Copyright (c) 2006-2020, RT-Thread Development Team
*
* SPDX-License-Identifier: Apache-2.0
*
* Change Logs:
* Date Author Notes
* 2020-04-16 bigmagic first version
* 2020-05-26 bigmagic add other uart
*/
#include <rthw.h>
#include <rtthread.h>
#include <rtdevice.h>
#include "board.h"
#include "drv_uart.h"
#include "drv_gpio.h"
#ifdef RT_USING_UART0
static struct rt_serial_device _serial0;
#endif
#ifdef RT_USING_UART1
static struct rt_serial_device _serial1;
#endif
#ifdef RT_USING_UART3
static struct rt_serial_device _serial3;
#endif
#ifdef RT_USING_UART4
static struct rt_serial_device _serial4;
#endif
#ifdef RT_USING_UART5
static struct rt_serial_device _serial5;
#endif
struct hw_uart_device
{
rt_ubase_t hw_base;
rt_uint32_t irqno;
};
static rt_err_t uart_configure(struct rt_serial_device *serial, struct serial_configure *cfg)
{
struct hw_uart_device *uart;
uint32_t bauddiv = (UART_REFERENCE_CLOCK / cfg->baud_rate)* 1000 / 16;
uint32_t ibrd = bauddiv / 1000;
RT_ASSERT(serial != RT_NULL);
uart = (struct hw_uart_device *)serial->parent.user_data;
if(uart->hw_base == AUX_BASE)
{
prev_raspi_pin_mode(GPIO_PIN_14, ALT5);
prev_raspi_pin_mode(GPIO_PIN_15, ALT5);
AUX_ENABLES(uart->hw_base) = 1; /* Enable UART1 */
AUX_MU_IER_REG(uart->hw_base) = 0; /* Disable interrupt */
AUX_MU_CNTL_REG(uart->hw_base) = 0; /* Disable Transmitter and Receiver */
AUX_MU_LCR_REG(uart->hw_base) = 3; /* Works in 8-bit mode */
AUX_MU_MCR_REG(uart->hw_base) = 0; /* Disable RTS */
AUX_MU_IIR_REG(uart->hw_base) = 0xC6; /* Enable FIFO, Clear FIFO */
AUX_MU_BAUD_REG(uart->hw_base) = 541; /* 115200 = system clock 500MHz / (8 * (baud + 1)), baud = 541 */
AUX_MU_CNTL_REG(uart->hw_base) = 3; /* Enable Transmitter and Receiver */
return RT_EOK;
}
if(uart->hw_base == UART0_BASE)
{
#ifndef BSP_USING_BULETOOTH
prev_raspi_pin_mode(GPIO_PIN_14, ALT0);
prev_raspi_pin_mode(GPIO_PIN_15, ALT0);
#else
prev_raspi_pin_mode(GPIO_PIN_30, ALT3);
prev_raspi_pin_mode(GPIO_PIN_31, ALT3);
prev_raspi_pin_mode(GPIO_PIN_32, ALT3);
prev_raspi_pin_mode(GPIO_PIN_33, ALT3);
#endif
}
if(uart->hw_base == UART3_BASE)
{
prev_raspi_pin_mode(GPIO_PIN_4, ALT4);
prev_raspi_pin_mode(GPIO_PIN_5, ALT4);
}
if(uart->hw_base == UART4_BASE)
{
prev_raspi_pin_mode(GPIO_PIN_8, ALT4);
prev_raspi_pin_mode(GPIO_PIN_9, ALT4);
}
if(uart->hw_base == UART5_BASE)
{
prev_raspi_pin_mode(GPIO_PIN_12, ALT4);
prev_raspi_pin_mode(GPIO_PIN_13, ALT4);
}
PL011_REG_IMSC(uart->hw_base) = 0; /* mask all interrupt */
PL011_REG_ICR(uart->hw_base) = 0x7ff; /* clear all interrupt */
//PL011 clock 480MHz 480x10^6/baudrate/16
PL011_REG_IBRD(uart->hw_base) = ibrd;
PL011_REG_FBRD(uart->hw_base) = (((bauddiv - ibrd * 1000) * 64 + 500) / 1000);
#ifdef BSP_USING_BULETOOTH
PL011_REG_IFLS(uart->hw_base) = 0x08;
PL011_REG_LCRH(uart->hw_base) = 0x70;
PL011_REG_CR(uart->hw_base) = PL011_CR_UARTEN | PL011_CR_TXE | PL011_CR_RXE | PL011_CR_RTS;
#else
PL011_REG_IFLS(uart->hw_base) = 0x0;
PL011_REG_LCRH(uart->hw_base) = PL011_LCRH_WLEN_8;
PL011_REG_CR(uart->hw_base) = PL011_CR_UARTEN | PL011_CR_TXE | PL011_CR_RXE;
#endif
PL011_REG_IMSC(uart->hw_base) = 0;
return RT_EOK;
}
static rt_err_t uart_control(struct rt_serial_device *serial, int cmd, void *arg)
{
struct hw_uart_device *uart;
RT_ASSERT(serial != RT_NULL);
uart = (struct hw_uart_device *)serial->parent.user_data;
switch (cmd)
{
case RT_DEVICE_CTRL_CLR_INT:
/* disable rx irq */
if(uart->hw_base == AUX_BASE)
{
AUX_MU_IER_REG(uart->hw_base) = 0x0;
}
else
{
PL011_REG_IMSC(uart->hw_base) &= ~((uint32_t)PL011_IMSC_RXIM);
}
rt_hw_interrupt_mask(uart->irqno);
break;
case RT_DEVICE_CTRL_SET_INT:
/* enable rx irq */
if(uart->hw_base == AUX_BASE)
{
AUX_MU_IER_REG(uart->hw_base) = 0x1;
}
else
{
PL011_REG_IMSC(uart->hw_base) |= PL011_IMSC_RXIM;
}
rt_hw_interrupt_umask(uart->irqno);
break;
}
return RT_EOK;
}
static int uart_putc(struct rt_serial_device *serial, char c)
{
struct hw_uart_device *uart;
RT_ASSERT(serial != RT_NULL);
uart = (struct hw_uart_device *)serial->parent.user_data;
if(uart->hw_base == AUX_BASE)
{
while (!(AUX_MU_LSR_REG(uart->hw_base) & 0x20));
AUX_MU_IO_REG(uart->hw_base) = c;
}
else
{
while ((PL011_REG_FR(uart->hw_base) & PL011_FR_TXFF));
PL011_REG_DR(uart->hw_base) = (uint8_t)c;
}
return 1;
}
static int uart_getc(struct rt_serial_device *serial)
{
int ch = -1;
struct hw_uart_device *uart;
RT_ASSERT(serial != RT_NULL);
uart = (struct hw_uart_device *)serial->parent.user_data;
if(uart->hw_base == AUX_BASE)
{
if ((AUX_MU_LSR_REG(uart->hw_base) & 0x01))
{
ch = AUX_MU_IO_REG(uart->hw_base) & 0xff;
}
}
else
{
if((PL011_REG_FR(uart->hw_base) & PL011_FR_RXFE) == 0)
{
ch = PL011_REG_DR(uart->hw_base) & 0xff;
}
}
return ch;
}
static const struct rt_uart_ops _uart_ops =
{
uart_configure,
uart_control,
uart_putc,
uart_getc,
};
#ifdef RT_USING_UART1
static void rt_hw_aux_uart_isr(int irqno, void *param)
{
struct rt_serial_device *serial = (struct rt_serial_device*)param;
rt_hw_serial_isr(serial, RT_SERIAL_EVENT_RX_IND);
}
#endif
static void rt_hw_uart_isr(int irqno, void *param)
{
#ifdef RT_USING_UART0
if((PACTL_CS & IRQ_UART0) == IRQ_UART0)
{
PACTL_CS &= ~(IRQ_UART0);
rt_hw_serial_isr(&_serial0, RT_SERIAL_EVENT_RX_IND);
PL011_REG_ICR(UART0_BASE) = PL011_INTERRUPT_RECEIVE;
}
#endif
#ifdef RT_USING_UART3
if((PACTL_CS & IRQ_UART3) == IRQ_UART3)
{
PACTL_CS &= ~(IRQ_UART3);
rt_hw_serial_isr(&_serial3, RT_SERIAL_EVENT_RX_IND);
PL011_REG_ICR(UART3_BASE) = PL011_INTERRUPT_RECEIVE;
}
#endif
#ifdef RT_USING_UART4
if((PACTL_CS & IRQ_UART4) == IRQ_UART4)
{
PACTL_CS &= ~(IRQ_UART4);
rt_hw_serial_isr(&_serial4, RT_SERIAL_EVENT_RX_IND);
PL011_REG_ICR(UART4_BASE) = PL011_INTERRUPT_RECEIVE;
}
#endif
#ifdef RT_USING_UART5
if((PACTL_CS & IRQ_UART5) == IRQ_UART5)
{
PACTL_CS &= ~(IRQ_UART5);
rt_hw_serial_isr(&_serial5, RT_SERIAL_EVENT_RX_IND);
PL011_REG_ICR(UART5_BASE) = PL011_INTERRUPT_RECEIVE;
}
#endif
}
#ifdef RT_USING_UART0
/* UART device driver structure */
static struct hw_uart_device _uart0_device =
{
UART0_BASE,
IRQ_PL011,
};
#endif
#ifdef RT_USING_UART1
/* UART device driver structure */
static struct hw_uart_device _uart1_device =
{
AUX_BASE,
IRQ_AUX_UART,
};
#endif
#ifdef RT_USING_UART3
static struct hw_uart_device _uart3_device =
{
UART3_BASE,
IRQ_PL011,
};
#endif
#ifdef RT_USING_UART4
static struct hw_uart_device _uart4_device =
{
UART4_BASE,
IRQ_PL011,
};
#endif
#ifdef RT_USING_UART5
static struct hw_uart_device _uart5_device =
{
UART5_BASE,
IRQ_PL011,
};
#endif
int rt_hw_uart_init(void)
{
struct serial_configure config = RT_SERIAL_CONFIG_DEFAULT;
#ifdef RT_USING_UART0
struct hw_uart_device *uart0;
uart0 = &_uart0_device;
_serial0.ops = &_uart_ops;
_serial0.config = config;
/* register UART0 device */
rt_hw_serial_register(&_serial0, "uart0",
RT_DEVICE_FLAG_RDWR | RT_DEVICE_FLAG_INT_RX,
uart0);
rt_hw_interrupt_install(uart0->irqno, rt_hw_uart_isr, &_serial0, "uart0");
#endif
#ifdef RT_USING_UART1
struct hw_uart_device *uart1;
uart1 = &_uart1_device;
_serial1.ops = &_uart_ops;
_serial1.config = config;
/* register UART1 device */
rt_hw_serial_register(&_serial1, "uart1",
RT_DEVICE_FLAG_RDWR | RT_DEVICE_FLAG_INT_RX,
uart1);
rt_hw_interrupt_install(uart1->irqno, rt_hw_aux_uart_isr, &_serial1, "uart1");
#endif
#ifdef RT_USING_UART3
struct hw_uart_device *uart3;
uart3 = &_uart3_device;
_serial3.ops = &_uart_ops;
_serial3.config = config;
/* register UART3 device */
rt_hw_serial_register(&_serial3, "uart3",
RT_DEVICE_FLAG_RDWR | RT_DEVICE_FLAG_INT_RX,
uart3);
rt_hw_interrupt_install(uart3->irqno, rt_hw_uart_isr, &_serial3, "uart3");
#endif
#ifdef RT_USING_UART4
struct hw_uart_device *uart4;
uart4 = &_uart4_device;
_serial4.ops = &_uart_ops;
_serial4.config = config;
/* register UART4 device */
rt_hw_serial_register(&_serial4, "uart4",
RT_DEVICE_FLAG_RDWR | RT_DEVICE_FLAG_INT_RX,
uart4);
rt_hw_interrupt_install(uart4->irqno, rt_hw_uart_isr, &_serial4, "uart4");
#endif
#ifdef RT_USING_UART5
struct hw_uart_device *uart5;
uart5 = &_uart5_device;
_serial5.ops = &_uart_ops;
_serial5.config = config;
/* register UART5 device */
rt_hw_serial_register(&_serial5, "uart5",
RT_DEVICE_FLAG_RDWR | RT_DEVICE_FLAG_INT_RX,
uart5);
rt_hw_interrupt_install(uart5->irqno, rt_hw_uart_isr, &_serial5, "uart5");
#endif
return 0;
}