rt-thread-official/bsp/bouffalo_lab/bl808/m0/board/board.c

199 lines
5.9 KiB
C

/*
* Copyright (c) 2006-2023, RT-Thread Development Team
*
* SPDX-License-Identifier: Apache-2.0
*
* Change Logs:
* Date Author Notes
* 2022/12/25 flyingcys first version
* 2023/01/17 chushicheng add pin and i2c
* 2023/03/15 flyingcys update bsp file structure
*/
#include <rthw.h>
#include <rtthread.h>
#include "board.h"
#include "drv_uart.h"
static void system_clock_init(void)
{
/* wifipll/audiopll */
GLB_Power_On_XTAL_And_PLL_CLK(GLB_XTAL_40M, GLB_PLL_WIFIPLL |
GLB_PLL_CPUPLL |
GLB_PLL_UHSPLL |
GLB_PLL_MIPIPLL);
GLB_Set_MCU_System_CLK(GLB_MCU_SYS_CLK_WIFIPLL_320M);
GLB_Set_DSP_System_CLK(GLB_DSP_SYS_CLK_CPUPLL_400M);
GLB_Config_CPU_PLL(GLB_XTAL_40M, cpuPllCfg_480M);
CPU_Set_MTimer_CLK(ENABLE, CPU_Get_MTimer_Source_Clock() / 1000 / 1000 - 1);
}
static void peripheral_clock_init(void)
{
PERIPHERAL_CLOCK_ADC_DAC_ENABLE();
PERIPHERAL_CLOCK_SEC_ENABLE();
PERIPHERAL_CLOCK_DMA0_ENABLE();
PERIPHERAL_CLOCK_UART0_ENABLE();
PERIPHERAL_CLOCK_UART1_ENABLE();
PERIPHERAL_CLOCK_SPI0_1_ENABLE();
PERIPHERAL_CLOCK_I2C0_ENABLE();
PERIPHERAL_CLOCK_PWM0_ENABLE();
PERIPHERAL_CLOCK_TIMER0_1_WDG_ENABLE();
PERIPHERAL_CLOCK_IR_ENABLE();
PERIPHERAL_CLOCK_I2S_ENABLE();
PERIPHERAL_CLOCK_USB_ENABLE();
PERIPHERAL_CLOCK_CAN_UART2_ENABLE();
GLB_Set_ADC_CLK(ENABLE, GLB_ADC_CLK_XCLK, 4);
GLB_Set_UART_CLK(ENABLE, HBN_UART_CLK_XCLK, 0);
GLB_Set_DSP_UART0_CLK(ENABLE, GLB_DSP_UART_CLK_DSP_XCLK, 0);
GLB_Set_SPI_CLK(ENABLE, GLB_SPI_CLK_MCU_MUXPLL_160M, 0);
GLB_Set_I2C_CLK(ENABLE, GLB_I2C_CLK_XCLK, 0);
GLB_Set_IR_CLK(ENABLE, GLB_IR_CLK_SRC_XCLK, 19);
GLB_Set_ADC_CLK(ENABLE, GLB_ADC_CLK_XCLK, 1);
GLB_Set_DIG_CLK_Sel(GLB_DIG_CLK_XCLK);
GLB_Set_DIG_512K_CLK(ENABLE, ENABLE, 0x4E);
GLB_Set_PWM1_IO_Sel(GLB_PWM1_IO_DIFF_END);
GLB_Set_CAM_CLK(ENABLE, GLB_CAM_CLK_WIFIPLL_96M, 3);
GLB_Set_PKA_CLK_Sel(GLB_PKA_CLK_MCU_MUXPLL_160M);
#ifdef BSP_USING_CSI
GLB_CSI_Config_MIPIPLL(2, 0x21000);
GLB_CSI_Power_Up_MIPIPLL();
GLB_Set_DSP_CLK(ENABLE, GLB_DSP_CLK_MUXPLL_160M, 1);
#endif
GLB_Set_USB_CLK_From_WIFIPLL(1);
}
#ifdef BSP_USING_PSRAM
#define WB_4MB_PSRAM (1)
#define UHS_32MB_PSRAM (2)
#define UHS_64MB_PSRAM (3)
#define WB_32MB_PSRAM (4)
#define NONE_UHS_PSRAM (-1)
int uhs_psram_init(void)
{
PSRAM_UHS_Cfg_Type psramDefaultCfg = {
2000,
PSRAM_MEM_SIZE_32MB,
PSRAM_PAGE_SIZE_2KB,
PSRAM_UHS_NORMAL_TEMP,
};
bflb_efuse_device_info_type chip_info;
bflb_ef_ctrl_get_device_info(&chip_info);
if (chip_info.psramInfo == UHS_32MB_PSRAM) {
psramDefaultCfg.psramMemSize = PSRAM_MEM_SIZE_32MB;
} else if (chip_info.psramInfo == UHS_64MB_PSRAM) {
psramDefaultCfg.psramMemSize = PSRAM_MEM_SIZE_64MB;
} else {
return -1;
}
//init uhs PLL; Must open uhs pll first, and then initialize uhs psram
GLB_Config_UHS_PLL(GLB_XTAL_40M, uhsPllCfg_2000M);
//init uhs psram ;
// Psram_UHS_x16_Init(Clock_Peripheral_Clock_Get(BL_PERIPHERAL_CLOCK_PSRAMA) / 1000000);
Psram_UHS_x16_Init_Override(&psramDefaultCfg);
Tzc_Sec_PSRAMA_Access_Release();
// example: 2000Mbps typical cal values
uhs_phy_cal_res->rl = 39;
uhs_phy_cal_res->rdqs = 3;
uhs_phy_cal_res->rdq = 0;
uhs_phy_cal_res->wl = 13;
uhs_phy_cal_res->wdqs = 4;
uhs_phy_cal_res->wdq = 5;
uhs_phy_cal_res->ck = 9;
/* TODO: use uhs psram trim update */
set_uhs_latency_r(uhs_phy_cal_res->rl);
cfg_dqs_rx(uhs_phy_cal_res->rdqs);
cfg_dq_rx(uhs_phy_cal_res->rdq);
set_uhs_latency_w(uhs_phy_cal_res->wl);
cfg_dq_drv(uhs_phy_cal_res->wdq);
cfg_ck_cen_drv(uhs_phy_cal_res->wdq + 4, uhs_phy_cal_res->wdq + 1);
cfg_dqs_drv(uhs_phy_cal_res->wdqs);
// set_odt_en();
mr_read_back();
return 0;
}
#endif
/* This is the timer interrupt service routine. */
static void systick_isr(void)
{
rt_tick_increase();
}
void rt_hw_board_init(void)
{
GLB_Halt_CPU(GLB_CORE_ID_D0);
GLB_Halt_CPU(GLB_CORE_ID_LP);
bflb_flash_init();
system_clock_init();
peripheral_clock_init();
bflb_irq_initialize();
bflb_mtimer_config(CPU_Get_MTimer_Clock() / RT_TICK_PER_SECOND, systick_isr);
#ifdef RT_USING_HEAP
/* initialize memory system */
rt_kprintf("RT_HW_HEAP_BEGIN:%x RT_HW_HEAP_END:%x size: %d\r\n", RT_HW_HEAP_BEGIN, RT_HW_HEAP_END, RT_HW_HEAP_END - RT_HW_HEAP_BEGIN);
rt_system_heap_init(RT_HW_HEAP_BEGIN, RT_HW_HEAP_END);
#endif
/* UART driver initialization is open by default */
#ifdef RT_USING_SERIAL
rt_hw_uart_init();
#endif
#ifdef BSP_USING_PSRAM
if (uhs_psram_init() < 0)
{
rt_kprintf("uhs_psram_init failed!\n");
}
#endif
/* Set the shell console output device */
#if defined(RT_USING_CONSOLE) && defined(RT_USING_DEVICE)
rt_console_set_device(RT_CONSOLE_DEVICE_NAME);
#endif
#ifdef RT_USING_COMPONENTS_INIT
rt_components_board_init();
#endif
#ifdef BSP_USING_TRIPLECORE
/* set CPU D0 boot XIP address and flash address */
Tzc_Sec_Set_CPU_Group(GLB_CORE_ID_D0, 1);
/* D0 boot from 0x58000000 */
GLB_Set_CPU_Reset_Address(GLB_CORE_ID_D0, 0x58000000);
/* D0 image offset on flash is CONFIG_D0_FLASH_ADDR */
bflb_sf_ctrl_set_flash_image_offset(CONFIG_D0_FLASH_ADDR, 1, SF_CTRL_FLASH_BANK0);
Tzc_Sec_Set_CPU_Group(GLB_CORE_ID_LP, 0);
/* LP boot from 0x580C0000 */
GLB_Set_CPU_Reset_Address(GLB_CORE_ID_LP, 0x58000000 + CONFIG_LP_FLASH_ADDR);
GLB_Release_CPU(GLB_CORE_ID_D0);
GLB_Release_CPU(GLB_CORE_ID_LP);
/* release d0 and then do can run */
BL_WR_WORD(IPC_SYNC_ADDR1, IPC_SYNC_FLAG);
BL_WR_WORD(IPC_SYNC_ADDR2, IPC_SYNC_FLAG);
L1C_DCache_Clean_By_Addr(IPC_SYNC_ADDR1, 8);
#endif
}
void rt_hw_cpu_reset(void)
{
GLB_SW_POR_Reset();
}
MSH_CMD_EXPORT_ALIAS(rt_hw_cpu_reset, reboot, reset machine);