libs/rt-thread-official
libs
/
rt-thread-official
mirror of https://github.com/RT-Thread/rt-thread.git
4
0
Fork 0
Code Issues Releases Wiki Activity
rt-thread-official/bsp/imxrt/libraries/MIMXRT1170/MIMXRT1176/drivers/fsl_flexio_mculcd.h

686 lines
24 KiB
C
Raw Blame History

/*
* Copyright (c) 2016, Freescale Semiconductor, Inc.
* Copyright 2016-2021 NXP
* All rights reserved.
*
* SPDX-License-Identifier: BSD-3-Clause
*/
#ifndef _FSL_FLEXIO_MCULCD_H_
#define _FSL_FLEXIO_MCULCD_H_
#include "fsl_common.h"
#include "fsl_flexio.h"
/*!
* @addtogroup flexio_mculcd
* @{
*/
/*******************************************************************************
* Definitions
******************************************************************************/
/*! @name Driver version */
/*@{*/
/*! @brief FlexIO MCULCD driver version. */
#define FSL_FLEXIO_MCULCD_DRIVER_VERSION (MAKE_VERSION(2, 0, 6))
/*@}*/
#ifndef FLEXIO_MCULCD_WAIT_COMPLETE_TIME
/*!
* @brief The delay time to wait for FLEXIO transmit complete.
*
* Currently there is no method to detect whether the data has been
* sent out from the shifter, so the driver use a software delay for this. When
* the data is written to shifter buffer, the driver call the delay
* function to wait for the data shift out.
* If this value is too small, then the last few bytes might be lost when writing
* data using interrupt method or DMA method.
*/
#define FLEXIO_MCULCD_WAIT_COMPLETE_TIME 512
#endif
#ifndef FLEXIO_MCULCD_DATA_BUS_WIDTH
/*!
* @brief The data bus width, must be 8 or 16.
*/
#define FLEXIO_MCULCD_DATA_BUS_WIDTH 16UL
#endif
#if (16UL != FLEXIO_MCULCD_DATA_BUS_WIDTH) && (8UL != FLEXIO_MCULCD_DATA_BUS_WIDTH)
#error Only support data bus 8-bit or 16-bit
#endif
/*! @brief FlexIO LCD transfer status */
enum
{
kStatus_FLEXIO_MCULCD_Idle = MAKE_STATUS(kStatusGroup_FLEXIO_MCULCD, 0), /*!< FlexIO LCD is idle. */
kStatus_FLEXIO_MCULCD_Busy = MAKE_STATUS(kStatusGroup_FLEXIO_MCULCD, 1), /*!< FlexIO LCD is busy */
kStatus_FLEXIO_MCULCD_Error = MAKE_STATUS(kStatusGroup_FLEXIO_MCULCD, 2), /*!< FlexIO LCD error occurred */
};
/*! @brief Define FlexIO MCULCD pixel format. */
typedef enum _flexio_mculcd_pixel_format
{
kFLEXIO_MCULCD_RGB565 = 0, /*!< RGB565, 16-bit. */
kFLEXIO_MCULCD_BGR565, /*!< BGR565, 16-bit. */
kFLEXIO_MCULCD_RGB888, /*!< RGB888, 24-bit. */
kFLEXIO_MCULCD_BGR888, /*!< BGR888, 24-bit. */
} flexio_mculcd_pixel_format_t;
/*! @brief Define FlexIO MCULCD bus type. */
typedef enum _flexio_mculcd_bus
{
kFLEXIO_MCULCD_8080, /*!< Using Intel 8080 bus. */
kFLEXIO_MCULCD_6800, /*!< Using Motorola 6800 bus. */
} flexio_mculcd_bus_t;
/*! @brief Define FlexIO MCULCD interrupt mask. */
enum _flexio_mculcd_interrupt_enable
{
kFLEXIO_MCULCD_TxEmptyInterruptEnable = (1U << 0U), /*!< Transmit buffer empty interrupt enable. */
kFLEXIO_MCULCD_RxFullInterruptEnable = (1U << 1U), /*!< Receive buffer full interrupt enable. */
};
/*! @brief Define FlexIO MCULCD status mask. */
enum _flexio_mculcd_status_flags
{
kFLEXIO_MCULCD_TxEmptyFlag = (1U << 0U), /*!< Transmit buffer empty flag. */
kFLEXIO_MCULCD_RxFullFlag = (1U << 1U), /*!< Receive buffer full flag. */
};
/*! @brief Define FlexIO MCULCD DMA mask. */
enum _flexio_mculcd_dma_enable
{
kFLEXIO_MCULCD_TxDmaEnable = 0x1U, /*!< Tx DMA request source */
kFLEXIO_MCULCD_RxDmaEnable = 0x2U, /*!< Rx DMA request source */
};
/*! @brief Function to set or clear the CS and RS pin. */
typedef void (*flexio_mculcd_pin_func_t)(bool set);
/*! @brief Define FlexIO MCULCD access structure typedef. */
typedef struct _flexio_mculcd_type
{
FLEXIO_Type *flexioBase; /*!< FlexIO base pointer. */
flexio_mculcd_bus_t busType; /*!< The bus type, 8080 or 6800. */
uint8_t dataPinStartIndex; /*!< Start index of the data pin, the FlexIO pin dataPinStartIndex
to (dataPinStartIndex + FLEXIO_MCULCD_DATA_BUS_WIDTH -1)
will be used for data transfer. Only support data bus width 8 and 16. */
uint8_t ENWRPinIndex; /*!< Pin select for WR(8080 mode), EN(6800 mode). */
uint8_t RDPinIndex; /*!< Pin select for RD(8080 mode), not used in 6800 mode. */
uint8_t txShifterStartIndex; /*!< Start index of shifters used for data write, it must be 0 or 4. */
uint8_t txShifterEndIndex; /*!< End index of shifters used for data write. */
uint8_t rxShifterStartIndex; /*!< Start index of shifters used for data read. */
uint8_t rxShifterEndIndex; /*!< End index of shifters used for data read, it must be 3 or 7. */
uint8_t timerIndex; /*!< Timer index used in FlexIO MCULCD. */
flexio_mculcd_pin_func_t setCSPin; /*!< Function to set or clear the CS pin. */
flexio_mculcd_pin_func_t setRSPin; /*!< Function to set or clear the RS pin. */
flexio_mculcd_pin_func_t setRDWRPin; /*!< Function to set or clear the RD/WR pin, only used in 6800 mode. */
} FLEXIO_MCULCD_Type;
/*! @brief Define FlexIO MCULCD configuration structure. */
typedef struct _flexio_mculcd_config
{
bool enable; /*!< Enable/disable FlexIO MCULCD after configuration. */
bool enableInDoze; /*!< Enable/disable FlexIO operation in doze mode. */
bool enableInDebug; /*!< Enable/disable FlexIO operation in debug mode. */
bool enableFastAccess; /*!< Enable/disable fast access to FlexIO registers,
fast access requires the FlexIO clock to be at least
twice the frequency of the bus clock. */
uint32_t baudRate_Bps; /*!< Baud rate in Bps. */
} flexio_mculcd_config_t;
/*! @brief Transfer mode.*/
typedef enum _flexio_mculcd_transfer_mode
{
kFLEXIO_MCULCD_ReadArray, /*!< Read data into an array. */
kFLEXIO_MCULCD_WriteArray, /*!< Write data from an array. */
kFLEXIO_MCULCD_WriteSameValue, /*!< Write the same value many times. */
} flexio_mculcd_transfer_mode_t;
/*! @brief Define FlexIO MCULCD transfer structure. */
typedef struct _flexio_mculcd_transfer
{
uint32_t command; /*!< Command to send. */
flexio_mculcd_transfer_mode_t mode; /*!< Transfer mode. */
uint32_t dataAddrOrSameValue; /*!< When sending the same value for many times,
this is the value to send. When writing or reading array,
this is the address of the data array. */
size_t dataSize; /*!< How many bytes to transfer. */
} flexio_mculcd_transfer_t;
/*! @brief typedef for flexio_mculcd_handle_t in advance. */
typedef struct _flexio_mculcd_handle flexio_mculcd_handle_t;
/*! @brief FlexIO MCULCD callback for finished transfer.
*
* When transfer finished, the callback function is called and returns the
* @p status as kStatus_FLEXIO_MCULCD_Idle.
*/
typedef void (*flexio_mculcd_transfer_callback_t)(FLEXIO_MCULCD_Type *base,
flexio_mculcd_handle_t *handle,
status_t status,
void *userData);
/*! @brief Define FlexIO MCULCD handle structure. */
struct _flexio_mculcd_handle
{
uint32_t dataAddrOrSameValue; /*!< When sending the same value for many times,
this is the value to send. When writing or reading array,
this is the address of the data array. */
size_t dataCount; /*!< Total count to be transferred. */
volatile size_t remainingCount; /*!< Remaining count to transfer. */
volatile uint32_t state; /*!< FlexIO MCULCD internal state. */
flexio_mculcd_transfer_callback_t completionCallback; /*!< FlexIO MCULCD transfer completed callback. */
void *userData; /*!< Callback parameter. */
};
/*******************************************************************************
* API
******************************************************************************/
#if defined(__cplusplus)
extern "C" {
#endif /*_cplusplus*/
/*!
* @name FlexIO MCULCD Configuration
* @{
*/
/*!
* @brief Ungates the FlexIO clock, resets the FlexIO module, configures the
* FlexIO MCULCD hardware, and configures the FlexIO MCULCD with FlexIO MCULCD
* configuration.
* The configuration structure can be filled by the user, or be set with default
* values
* by the @ref FLEXIO_MCULCD_GetDefaultConfig.
*
* @param base Pointer to the FLEXIO_MCULCD_Type structure.
* @param config Pointer to the flexio_mculcd_config_t structure.
* @param srcClock_Hz FlexIO source clock in Hz.
* @retval kStatus_Success Initialization success.
* @retval kStatus_InvalidArgument Initialization failed because of invalid
* argument.
*/
status_t FLEXIO_MCULCD_Init(FLEXIO_MCULCD_Type *base, flexio_mculcd_config_t *config, uint32_t srcClock_Hz);
/*!
* @brief Resets the FLEXIO_MCULCD timer and shifter configuration.
*
* @param base Pointer to the FLEXIO_MCULCD_Type.
*/
void FLEXIO_MCULCD_Deinit(FLEXIO_MCULCD_Type *base);
/*!
* @brief Gets the default configuration to configure the FlexIO MCULCD.
*
* The default configuration value is:
* @code
* config->enable = true;
* config->enableInDoze = false;
* config->enableInDebug = true;
* config->enableFastAccess = true;
* config->baudRate_Bps = 96000000U;
* @endcode
* @param config Pointer to the flexio_mculcd_config_t structure.
*/
void FLEXIO_MCULCD_GetDefaultConfig(flexio_mculcd_config_t *config);
/*@}*/
/*!
* @name Status
* @{
*/
/*!
* @brief Gets FlexIO MCULCD status flags.
*
* @param base Pointer to the FLEXIO_MCULCD_Type structure.
* @return status flag; OR'ed value or the @ref _flexio_mculcd_status_flags.
*
* @note Don't use this function with DMA APIs.
*/
uint32_t FLEXIO_MCULCD_GetStatusFlags(FLEXIO_MCULCD_Type *base);
/*!
* @brief Clears FlexIO MCULCD status flags.
*
* @param base Pointer to the FLEXIO_MCULCD_Type structure.
* @param mask Status to clear, it is the OR'ed value of @ref
* _flexio_mculcd_status_flags.
*
* @note Don't use this function with DMA APIs.
*/
void FLEXIO_MCULCD_ClearStatusFlags(FLEXIO_MCULCD_Type *base, uint32_t mask);
/*@}*/
/*!
* @name Interrupts
* @{
*/
/*!
* @brief Enables the FlexIO MCULCD interrupt.
*
* This function enables the FlexIO MCULCD interrupt.
*
* @param base Pointer to the FLEXIO_MCULCD_Type structure.
* @param mask Interrupts to enable, it is the OR'ed value of @ref
* _flexio_mculcd_interrupt_enable.
*/
void FLEXIO_MCULCD_EnableInterrupts(FLEXIO_MCULCD_Type *base, uint32_t mask);
/*!
* @brief Disables the FlexIO MCULCD interrupt.
*
* This function disables the FlexIO MCULCD interrupt.
*
* @param base Pointer to the FLEXIO_MCULCD_Type structure.
* @param mask Interrupts to disable, it is the OR'ed value of @ref
* _flexio_mculcd_interrupt_enable.
*/
void FLEXIO_MCULCD_DisableInterrupts(FLEXIO_MCULCD_Type *base, uint32_t mask);
/*@}*/
/*!
* @name DMA Control
* @{
*/
/*!
* @brief Enables/disables the FlexIO MCULCD transmit DMA.
*
* @param base Pointer to the FLEXIO_MCULCD_Type structure.
* @param enable True means enable DMA, false means disable DMA.
*/
static inline void FLEXIO_MCULCD_EnableTxDMA(FLEXIO_MCULCD_Type *base, bool enable)
{
FLEXIO_EnableShifterStatusDMA(base->flexioBase, (1UL << base->txShifterStartIndex), enable);
}
/*!
* @brief Enables/disables the FlexIO MCULCD receive DMA.
*
* @param base Pointer to the FLEXIO_MCULCD_Type structure.
* @param enable True means enable DMA, false means disable DMA.
*/
static inline void FLEXIO_MCULCD_EnableRxDMA(FLEXIO_MCULCD_Type *base, bool enable)
{
FLEXIO_EnableShifterStatusDMA(base->flexioBase, (1UL << base->rxShifterEndIndex), enable);
}
/*!
* @brief Gets the FlexIO MCULCD transmit data register address.
*
* This function returns the MCULCD data register address, which is mainly used
* by DMA/eDMA.
*
* @param base Pointer to the FLEXIO_MCULCD_Type structure.
* @return FlexIO MCULCD transmit data register address.
*/
static inline uint32_t FLEXIO_MCULCD_GetTxDataRegisterAddress(FLEXIO_MCULCD_Type *base)
{
return (uint32_t) & (base->flexioBase->SHIFTBUF[base->txShifterStartIndex]);
}
/*!
* @brief Gets the FlexIO MCULCD receive data register address.
*
* This function returns the MCULCD data register address, which is mainly used
* by DMA/eDMA.
*
* @param base Pointer to the FLEXIO_MCULCD_Type structure.
* @return FlexIO MCULCD receive data register address.
*/
static inline uint32_t FLEXIO_MCULCD_GetRxDataRegisterAddress(FLEXIO_MCULCD_Type *base)
{
return (uint32_t) & (base->flexioBase->SHIFTBUF[base->rxShifterStartIndex]);
}
/*@}*/
/*!
* @name Bus Operations
* @{
*/
/*!
* @brief Set desired baud rate.
*
* @param base Pointer to the FLEXIO_MCULCD_Type structure.
* @param baudRate_Bps Desired baud rate.
* @param srcClock_Hz FLEXIO clock frequency in Hz.
* @retval kStatus_Success Set successfully.
* @retval kStatus_InvalidArgument Could not set the baud rate.
*/
status_t FLEXIO_MCULCD_SetBaudRate(FLEXIO_MCULCD_Type *base, uint32_t baudRate_Bps, uint32_t srcClock_Hz);
/*!
* @brief Configures the FLEXIO MCULCD to multiple beats write mode.
*
* At the begining multiple beats write operation, the FLEXIO MCULCD is configured to
* multiple beats write mode using this function. After write operation, the configuration
* is cleared by @ref FLEXIO_MCULCD_ClearSingleBeatWriteConfig.
*
* @param base Pointer to the FLEXIO_MCULCD_Type.
*
* @note This is an internal used function, upper layer should not use.
*/
void FLEXIO_MCULCD_SetSingleBeatWriteConfig(FLEXIO_MCULCD_Type *base);
/*!
* @brief Clear the FLEXIO MCULCD multiple beats write mode configuration.
*
* Clear the write configuration set by @ref FLEXIO_MCULCD_SetSingleBeatWriteConfig.
*
* @param base Pointer to the FLEXIO_MCULCD_Type.
*
* @note This is an internal used function, upper layer should not use.
*/
void FLEXIO_MCULCD_ClearSingleBeatWriteConfig(FLEXIO_MCULCD_Type *base);
/*!
* @brief Configures the FLEXIO MCULCD to multiple beats read mode.
*
* At the begining or multiple beats read operation, the FLEXIO MCULCD is configured
* to multiple beats read mode using this function. After read operation, the configuration
* is cleared by @ref FLEXIO_MCULCD_ClearSingleBeatReadConfig.
*
* @param base Pointer to the FLEXIO_MCULCD_Type.
*
* @note This is an internal used function, upper layer should not use.
*/
void FLEXIO_MCULCD_SetSingleBeatReadConfig(FLEXIO_MCULCD_Type *base);
/*!
* @brief Clear the FLEXIO MCULCD multiple beats read mode configuration.
*
* Clear the read configuration set by @ref FLEXIO_MCULCD_SetSingleBeatReadConfig.
*
* @param base Pointer to the FLEXIO_MCULCD_Type.
*
* @note This is an internal used function, upper layer should not use.
*/
void FLEXIO_MCULCD_ClearSingleBeatReadConfig(FLEXIO_MCULCD_Type *base);
/*!
* @brief Configures the FLEXIO MCULCD to multiple beats write mode.
*
* At the begining multiple beats write operation, the FLEXIO MCULCD is configured to
* multiple beats write mode using this function. After write operation, the configuration
* is cleared by FLEXIO_MCULCD_ClearMultBeatsWriteConfig.
*
* @param base Pointer to the FLEXIO_MCULCD_Type.
*
* @note This is an internal used function, upper layer should not use.
*/
void FLEXIO_MCULCD_SetMultiBeatsWriteConfig(FLEXIO_MCULCD_Type *base);
/*!
* @brief Clear the FLEXIO MCULCD multiple beats write mode configuration.
*
* Clear the write configuration set by FLEXIO_MCULCD_SetMultBeatsWriteConfig.
*
* @param base Pointer to the FLEXIO_MCULCD_Type.
*
* @note This is an internal used function, upper layer should not use.
*/
void FLEXIO_MCULCD_ClearMultiBeatsWriteConfig(FLEXIO_MCULCD_Type *base);
/*!
* @brief Configures the FLEXIO MCULCD to multiple beats read mode.
*
* At the begining or multiple beats read operation, the FLEXIO MCULCD is configured
* to multiple beats read mode using this function. After read operation, the configuration
* is cleared by FLEXIO_MCULCD_ClearMultBeatsReadConfig.
*
* @param base Pointer to the FLEXIO_MCULCD_Type.
*
* @note This is an internal used function, upper layer should not use.
*/
void FLEXIO_MCULCD_SetMultiBeatsReadConfig(FLEXIO_MCULCD_Type *base);
/*!
* @brief Clear the FLEXIO MCULCD multiple beats read mode configuration.
*
* Clear the read configuration set by FLEXIO_MCULCD_SetMultBeatsReadConfig.
*
* @param base Pointer to the FLEXIO_MCULCD_Type.
*
* @note This is an internal used function, upper layer should not use.
*/
void FLEXIO_MCULCD_ClearMultiBeatsReadConfig(FLEXIO_MCULCD_Type *base);
/*!
* @brief Enables/disables the FlexIO MCULCD module operation.
*
* @param base Pointer to the FLEXIO_MCULCD_Type.
* @param enable True to enable, false does not have any effect.
*/
static inline void FLEXIO_MCULCD_Enable(FLEXIO_MCULCD_Type *base, bool enable)
{
if (enable)
{
FLEXIO_Enable(base->flexioBase, enable);
}
}
/*!
* @brief Read data from the FLEXIO MCULCD RX shifter buffer.
*
* Read data from the RX shift buffer directly, it does no check whether the
* buffer is empty or not.
*
* If the data bus width is 8-bit:
* @code
* uint8_t value;
* value = (uint8_t)FLEXIO_MCULCD_ReadData(base);
* @endcode
*
* If the data bus width is 16-bit:
* @code
* uint16_t value;
* value = (uint16_t)FLEXIO_MCULCD_ReadData(base);
* @endcode
*
* @note This function returns the RX shifter buffer value (32-bit) directly.
* The return value should be converted according to data bus width.
*
* @param base Pointer to the FLEXIO_MCULCD_Type structure.
* @return The data read out.
*
* @note Don't use this function with DMA APIs.
*/
uint32_t FLEXIO_MCULCD_ReadData(FLEXIO_MCULCD_Type *base);
/*!
* @brief Write data into the FLEXIO MCULCD TX shifter buffer.
*
* Write data into the TX shift buffer directly, it does no check whether the
* buffer is full or not.
*
* @param base Pointer to the FLEXIO_MCULCD_Type structure.
* @param data The data to write.
*
* @note Don't use this function with DMA APIs.
*/
static inline void FLEXIO_MCULCD_WriteData(FLEXIO_MCULCD_Type *base, uint32_t data)
{
base->flexioBase->SHIFTBUF[base->txShifterStartIndex] = data;
}
/*!
* @brief Assert the nCS to start transfer.
*
* @param base Pointer to the FLEXIO_MCULCD_Type structure.
*/
static inline void FLEXIO_MCULCD_StartTransfer(FLEXIO_MCULCD_Type *base)
{
base->setCSPin(false);
}
/*!
* @brief De-assert the nCS to stop transfer.
*
* @param base Pointer to the FLEXIO_MCULCD_Type structure.
*/
static inline void FLEXIO_MCULCD_StopTransfer(FLEXIO_MCULCD_Type *base)
{
base->setCSPin(true);
}
/*!
* @brief Wait for transmit data send out finished.
*
* Currently there is no effective method to wait for the data send out
* from the shiter, so here use a while loop to wait.
*
* @note This is an internal used function.
*/
void FLEXIO_MCULCD_WaitTransmitComplete(void);
/*!
* @brief Send command in blocking way.
*
* This function sends the command and returns when the command has been sent
* out.
*
* @param base Pointer to the FLEXIO_MCULCD_Type structure.
* @param command The command to send.
*/
void FLEXIO_MCULCD_WriteCommandBlocking(FLEXIO_MCULCD_Type *base, uint32_t command);
/*!
* @brief Send data array in blocking way.
*
* This function sends the data array and returns when the data sent out.
*
* @param base Pointer to the FLEXIO_MCULCD_Type structure.
* @param data The data array to send.
* @param size How many bytes to write.
*/
void FLEXIO_MCULCD_WriteDataArrayBlocking(FLEXIO_MCULCD_Type *base, const void *data, size_t size);
/*!
* @brief Read data into array in blocking way.
*
* This function reads the data into array and returns when the data read
* finished.
*
* @param base Pointer to the FLEXIO_MCULCD_Type structure.
* @param data The array to save the data.
* @param size How many bytes to read.
*/
void FLEXIO_MCULCD_ReadDataArrayBlocking(FLEXIO_MCULCD_Type *base, void *data, size_t size);
/*!
* @brief Send the same value many times in blocking way.
*
* This function sends the same value many times. It could be used to clear the
* LCD screen. If the data bus width is 8, this function will send LSB 8 bits of
* @p sameValue for @p size times. If the data bus is 16, this function will send
* LSB 16 bits of @p sameValue for @p size / 2 times.
*
* @param base Pointer to the FLEXIO_MCULCD_Type structure.
* @param sameValue The same value to send.
* @param size How many bytes to send.
*/
void FLEXIO_MCULCD_WriteSameValueBlocking(FLEXIO_MCULCD_Type *base, uint32_t sameValue, size_t size);
/*!
* @brief Performs a polling transfer.
*
* @note The API does not return until the transfer finished.
*
* @param base pointer to FLEXIO_MCULCD_Type structure.
* @param xfer pointer to flexio_mculcd_transfer_t structure.
*/
void FLEXIO_MCULCD_TransferBlocking(FLEXIO_MCULCD_Type *base, flexio_mculcd_transfer_t *xfer);
/*@}*/
/*!
* @name Transactional
* @{
*/
/*!
* @brief Initializes the FlexIO MCULCD handle, which is used in transactional
* functions.
*
* @param base Pointer to the FLEXIO_MCULCD_Type structure.
* @param handle Pointer to the flexio_mculcd_handle_t structure to store the
* transfer state.
* @param callback The callback function.
* @param userData The parameter of the callback function.
* @retval kStatus_Success Successfully create the handle.
* @retval kStatus_OutOfRange The FlexIO type/handle/ISR table out of range.
*/
status_t FLEXIO_MCULCD_TransferCreateHandle(FLEXIO_MCULCD_Type *base,
flexio_mculcd_handle_t *handle,
flexio_mculcd_transfer_callback_t callback,
void *userData);
/*!
* @brief Transfer data using IRQ.
*
* This function sends data using IRQ. This is a non-blocking function, which
* returns right away. When all data is sent out/received, the callback
* function is called.
*
* @param base Pointer to the FLEXIO_MCULCD_Type structure.
* @param handle Pointer to the flexio_mculcd_handle_t structure to store the
* transfer state.
* @param xfer FlexIO MCULCD transfer structure. See #flexio_mculcd_transfer_t.
* @retval kStatus_Success Successfully start a transfer.
* @retval kStatus_InvalidArgument Input argument is invalid.
* @retval kStatus_FLEXIO_MCULCD_Busy MCULCD is busy with another transfer.
*/
status_t FLEXIO_MCULCD_TransferNonBlocking(FLEXIO_MCULCD_Type *base,
flexio_mculcd_handle_t *handle,
flexio_mculcd_transfer_t *xfer);
/*!
* @brief Aborts the data transfer, which used IRQ.
*
* @param base Pointer to the FLEXIO_MCULCD_Type structure.
* @param handle Pointer to the flexio_mculcd_handle_t structure to store the
* transfer state.
*/
void FLEXIO_MCULCD_TransferAbort(FLEXIO_MCULCD_Type *base, flexio_mculcd_handle_t *handle);
/*!
* @brief Gets the data transfer status which used IRQ.
*
* @param base Pointer to the FLEXIO_MCULCD_Type structure.
* @param handle Pointer to the flexio_mculcd_handle_t structure to store the
* transfer state.
* @param count How many bytes transferred so far by the non-blocking transaction.
* @retval kStatus_Success Get the transferred count Successfully.
* @retval kStatus_NoTransferInProgress No transfer in process.
*/
status_t FLEXIO_MCULCD_TransferGetCount(FLEXIO_MCULCD_Type *base, flexio_mculcd_handle_t *handle, size_t *count);
/*!
* @brief FlexIO MCULCD IRQ handler function.
*
* @param base Pointer to the FLEXIO_MCULCD_Type structure.
* @param handle Pointer to the flexio_mculcd_handle_t structure to store the
* transfer state.
*/
void FLEXIO_MCULCD_TransferHandleIRQ(void *base, void *handle);
/*@}*/
#if defined(__cplusplus)
}
#endif /*_cplusplus*/
/*@}*/
#endif /*_FSL_FLEXIO_MCULCD_H_*/
View Git Blame Copy Permalink