265 lines
8.1 KiB
C
265 lines
8.1 KiB
C
/**
|
|
* \file
|
|
*
|
|
* \brief SAM Watchdog Driver
|
|
*
|
|
* Copyright (C) 2012-2016 Atmel Corporation. All rights reserved.
|
|
*
|
|
* \asf_license_start
|
|
*
|
|
* \page License
|
|
*
|
|
* Redistribution and use in source and binary forms, with or without
|
|
* modification, are permitted provided that the following conditions are met:
|
|
*
|
|
* 1. Redistributions of source code must retain the above copyright notice,
|
|
* this list of conditions and the following disclaimer.
|
|
*
|
|
* 2. Redistributions in binary form must reproduce the above copyright notice,
|
|
* this list of conditions and the following disclaimer in the documentation
|
|
* and/or other materials provided with the distribution.
|
|
*
|
|
* 3. The name of Atmel may not be used to endorse or promote products derived
|
|
* from this software without specific prior written permission.
|
|
*
|
|
* 4. This software may only be redistributed and used in connection with an
|
|
* Atmel microcontroller product.
|
|
*
|
|
* THIS SOFTWARE IS PROVIDED BY ATMEL "AS IS" AND ANY EXPRESS OR IMPLIED
|
|
* WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF
|
|
* MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND NON-INFRINGEMENT ARE
|
|
* EXPRESSLY AND SPECIFICALLY DISCLAIMED. IN NO EVENT SHALL ATMEL BE LIABLE FOR
|
|
* ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL
|
|
* DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS
|
|
* OR SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION)
|
|
* HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT,
|
|
* STRICT LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN
|
|
* ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE
|
|
* POSSIBILITY OF SUCH DAMAGE.
|
|
*
|
|
* \asf_license_stop
|
|
*
|
|
*/
|
|
/*
|
|
* Support and FAQ: visit <a href="http://www.atmel.com/design-support/">Atmel Support</a>
|
|
*/
|
|
#include "wdt.h"
|
|
#include <system.h>
|
|
|
|
/**
|
|
* \brief Sets up the WDT hardware module based on the configuration.
|
|
*
|
|
* Writes a given configuration of a WDT configuration to the
|
|
* hardware module, and initializes the internal device struct.
|
|
*
|
|
* \param[in] config Pointer to the configuration struct
|
|
*
|
|
* \return Status of the configuration procedure.
|
|
*
|
|
* \retval STATUS_OK If the module was configured correctly
|
|
* \retval STATUS_ERR_INVALID_ARG If invalid argument(s) were supplied
|
|
* \retval STATUS_ERR_IO If the Watchdog module is locked to be always on
|
|
*/
|
|
#if (SAML21) || (SAML22) || (SAMC20) || (SAMC21) || (SAMR30)
|
|
enum status_code wdt_set_config(
|
|
const struct wdt_conf *const config)
|
|
{
|
|
/* Sanity check arguments */
|
|
Assert(config);
|
|
|
|
Wdt *const WDT_module = WDT;
|
|
|
|
/* Turn on the digital interface clock */
|
|
system_apb_clock_set_mask(SYSTEM_CLOCK_APB_APBA, MCLK_APBAMASK_WDT);
|
|
|
|
/* Check of the Watchdog has been locked to be always on, if so, abort */
|
|
if (wdt_is_locked()) {
|
|
return STATUS_ERR_IO;
|
|
}
|
|
|
|
/* Check for an invalid timeout period, abort if found */
|
|
if (config->timeout_period == WDT_PERIOD_NONE) {
|
|
return STATUS_ERR_INVALID_ARG;
|
|
}
|
|
|
|
/* Make sure the Window and Early Warning periods are not more than the
|
|
* reset period, abort if either is invalid */
|
|
if ((config->timeout_period < config->window_period) ||
|
|
(config->timeout_period < config->early_warning_period)) {
|
|
return STATUS_ERR_INVALID_ARG;
|
|
}
|
|
|
|
/* Disable the Watchdog module */
|
|
WDT_module->CTRLA.reg &= ~WDT_CTRLA_ENABLE;
|
|
|
|
while (wdt_is_syncing()) {
|
|
/* Wait for all hardware modules to complete synchronization */
|
|
}
|
|
|
|
if(config->enable == false) {
|
|
return STATUS_OK;
|
|
}
|
|
|
|
uint32_t new_config = 0;
|
|
|
|
/* Update the timeout period value with the requested period */
|
|
new_config |= (config->timeout_period - 1) << WDT_CONFIG_PER_Pos;
|
|
|
|
/* Check if the user has requested a reset window period */
|
|
if (config->window_period != WDT_PERIOD_NONE) {
|
|
WDT_module->CTRLA.reg |= WDT_CTRLA_WEN;
|
|
|
|
/* Update and enable the timeout period value */
|
|
new_config |= (config->window_period - 1) << WDT_CONFIG_WINDOW_Pos;
|
|
} else {
|
|
/* Ensure the window enable control flag is cleared */
|
|
WDT_module->CTRLA.reg &= ~WDT_CTRLA_WEN;
|
|
}
|
|
|
|
while (wdt_is_syncing()) {
|
|
/* Wait for all hardware modules to complete synchronization */
|
|
}
|
|
|
|
/* Write the new Watchdog configuration */
|
|
WDT_module->CONFIG.reg = new_config;
|
|
|
|
/* Check if the user has requested an early warning period */
|
|
if (config->early_warning_period != WDT_PERIOD_NONE) {
|
|
/* Set the Early Warning period */
|
|
WDT_module->EWCTRL.reg
|
|
= (config->early_warning_period - 1) << WDT_EWCTRL_EWOFFSET_Pos;
|
|
}
|
|
|
|
/* Either enable or lock-enable the Watchdog timer depending on the user
|
|
* settings */
|
|
if (config->always_on) {
|
|
WDT_module->CTRLA.reg |= WDT_CTRLA_ALWAYSON;
|
|
} else {
|
|
WDT_module->CTRLA.reg |= WDT_CTRLA_ENABLE;
|
|
}
|
|
|
|
while (wdt_is_syncing()) {
|
|
/* Wait for all hardware modules to complete synchronization */
|
|
}
|
|
|
|
return STATUS_OK;
|
|
}
|
|
#else
|
|
enum status_code wdt_set_config(
|
|
const struct wdt_conf *const config)
|
|
{
|
|
/* Sanity check arguments */
|
|
Assert(config);
|
|
|
|
Wdt *const WDT_module = WDT;
|
|
|
|
/* Turn on the digital interface clock */
|
|
system_apb_clock_set_mask(SYSTEM_CLOCK_APB_APBA, PM_APBAMASK_WDT);
|
|
|
|
/* Check of the Watchdog has been locked to be always on, if so, abort */
|
|
if (wdt_is_locked()) {
|
|
return STATUS_ERR_IO;
|
|
}
|
|
|
|
/* Check for an invalid timeout period, abort if found */
|
|
if (config->timeout_period == WDT_PERIOD_NONE) {
|
|
return STATUS_ERR_INVALID_ARG;
|
|
}
|
|
|
|
/* Make sure the Window and Early Warning periods are not more than the
|
|
* reset period, abort if either is invalid */
|
|
if ((config->timeout_period < config->window_period) ||
|
|
(config->timeout_period < config->early_warning_period)) {
|
|
return STATUS_ERR_INVALID_ARG;
|
|
}
|
|
|
|
/* Disable the Watchdog module */
|
|
WDT_module->CTRL.reg &= ~WDT_CTRL_ENABLE;
|
|
|
|
while (wdt_is_syncing()) {
|
|
/* Wait for all hardware modules to complete synchronization */
|
|
}
|
|
|
|
if(config->enable == false) {
|
|
return STATUS_OK;
|
|
}
|
|
|
|
/* Configure GCLK channel and enable clock */
|
|
struct system_gclk_chan_config gclk_chan_conf;
|
|
gclk_chan_conf.source_generator = config->clock_source;
|
|
system_gclk_chan_set_config(WDT_GCLK_ID, &gclk_chan_conf);
|
|
system_gclk_chan_enable(WDT_GCLK_ID);
|
|
if (config->always_on) {
|
|
system_gclk_chan_lock(WDT_GCLK_ID);
|
|
}
|
|
|
|
uint32_t new_config = 0;
|
|
|
|
/* Update the timeout period value with the requested period */
|
|
new_config |= (config->timeout_period - 1) << WDT_CONFIG_PER_Pos;
|
|
|
|
/* Check if the user has requested a reset window period */
|
|
if (config->window_period != WDT_PERIOD_NONE) {
|
|
WDT_module->CTRL.reg |= WDT_CTRL_WEN;
|
|
|
|
/* Update and enable the timeout period value */
|
|
new_config |= (config->window_period - 1) << WDT_CONFIG_WINDOW_Pos;
|
|
} else {
|
|
/* Ensure the window enable control flag is cleared */
|
|
WDT_module->CTRL.reg &= ~WDT_CTRL_WEN;
|
|
}
|
|
|
|
while (wdt_is_syncing()) {
|
|
/* Wait for all hardware modules to complete synchronization */
|
|
}
|
|
|
|
/* Write the new Watchdog configuration */
|
|
WDT_module->CONFIG.reg = new_config;
|
|
|
|
/* Check if the user has requested an early warning period */
|
|
if (config->early_warning_period != WDT_PERIOD_NONE) {
|
|
while (wdt_is_syncing()) {
|
|
/* Wait for all hardware modules to complete synchronization */
|
|
}
|
|
|
|
/* Set the Early Warning period */
|
|
WDT_module->EWCTRL.reg
|
|
= (config->early_warning_period - 1) << WDT_EWCTRL_EWOFFSET_Pos;
|
|
}
|
|
|
|
/* Either enable or lock-enable the Watchdog timer depending on the user
|
|
* settings */
|
|
if (config->always_on) {
|
|
WDT_module->CTRL.reg |= WDT_CTRL_ALWAYSON;
|
|
} else {
|
|
WDT_module->CTRL.reg |= WDT_CTRL_ENABLE;
|
|
}
|
|
|
|
while (wdt_is_syncing()) {
|
|
/* Wait for all hardware modules to complete synchronization */
|
|
}
|
|
|
|
return STATUS_OK;
|
|
}
|
|
#endif
|
|
|
|
/**
|
|
* \brief Resets the count of the running Watchdog Timer that was previously enabled.
|
|
*
|
|
* Resets the current count of the Watchdog Timer, restarting the timeout
|
|
* period count elapsed. This function should be called after the window
|
|
* period (if one was set in the module configuration) but before the timeout
|
|
* period to prevent a reset of the system.
|
|
*/
|
|
void wdt_reset_count(void)
|
|
{
|
|
Wdt *const WDT_module = WDT;
|
|
|
|
/* Disable the Watchdog module */
|
|
WDT_module->CLEAR.reg = WDT_CLEAR_CLEAR_KEY;
|
|
|
|
while (wdt_is_syncing()) {
|
|
/* Wait for all hardware modules to complete synchronization */
|
|
}
|
|
}
|