rt-thread-official/bsp/ra6m4-cpk/drivers/Kconfig

236 lines
7.0 KiB
Plaintext

menu "Hardware Drivers Config"
config SOC_SERIES_R7FA6M4AF
bool
select RT_USING_COMPONENTS_INIT
select RT_USING_USER_MAIN
default y
menu "Onboard Peripheral Drivers"
endmenu
menu "On-chip Peripheral Drivers"
config BSP_USING_GPIO
bool "Enable GPIO"
select RT_USING_PIN
default y
config BSP_USING_ONCHIP_FLASH
bool "Enable Onchip FLASH"
default n
config BSP_USING_WDT
bool "Enable Watchdog Timer"
select RT_USING_WDT
default n
menuconfig BSP_USING_UART
bool "Enable UART"
default y
select RT_USING_SERIAL
select RT_USING_SERIAL_V2
if BSP_USING_UART
menuconfig BSP_USING_UART7
bool "Enable UART7 (Console)"
default y
if BSP_USING_UART7
config BSP_UART7_RX_USING_DMA
bool "Enable UART7 RX DMA"
depends on BSP_USING_UART7 && RT_SERIAL_USING_DMA
default n
config BSP_UART7_TX_USING_DMA
bool "Enable UART7 TX DMA"
depends on BSP_USING_UART7 && RT_SERIAL_USING_DMA
default n
config BSP_UART7_RX_BUFSIZE
int "Set UART7 RX buffer size"
range 64 65535
depends on RT_USING_SERIAL_V2
default 256
config BSP_UART7_TX_BUFSIZE
int "Set UART7 TX buffer size"
range 0 65535
depends on RT_USING_SERIAL_V2
default 0
endif
endif
menuconfig BSP_USING_I2C
bool "Enable I2C BUS"
default n
select RT_USING_I2C
select RT_USING_I2C_BITOPS
select RT_USING_PIN
if BSP_USING_I2C
menuconfig BSP_USING_I2C1
bool "Enable I2C1 BUS (software simulation)"
default y
if BSP_USING_I2C1
config BSP_I2C1_SCL_PIN
hex "i2c1 scl pin number"
range 0x0000 0x0B0F
default 0x0512
config BSP_I2C1_SDA_PIN
hex "I2C1 sda pin number"
range 0x0000 0x0B0F
default 0x0511
endif
endif
menuconfig BSP_USING_ONCHIP_RTC
bool "Enable RTC"
select RT_USING_RTC
default n
if BSP_USING_ONCHIP_RTC
endif
menuconfig BSP_USING_SPI
bool "Enable SPI BUS"
default n
select RT_USING_SPI
if BSP_USING_SPI
config BSP_SPI_USING_DTC_DMA
bool "Enable SPI DTC transfers data without using the CPU."
default n
config BSP_USING_SPI0
bool "Enable SPI0 BUS"
default n
config BSP_USING_SPI1
bool "Enable SPI1 BUS"
default n
endif
menuconfig BSP_USING_ADC
bool "Enable ADC"
default n
select RT_USING_ADC
if BSP_USING_ADC
config BSP_USING_ADC0
bool "Enable ADC0"
default n
config BSP_USING_ADC1
bool "Enable ADC1"
default n
endif
menuconfig BSP_USING_DAC
bool "Enable DAC"
default n
select RT_USING_DAC
if BSP_USING_DAC
config BSP_USING_DAC0
bool "Enable DAC0"
default n
config BSP_USING_DAC1
bool "Enable DAC1"
default n
endif
menuconfig BSP_USING_PWM
bool "Enable PWM"
default n
select RT_USING_PWM
if BSP_USING_PWM
config BSP_USING_PWM0
bool "Enable GPT0 (32-Bits) output PWM"
default n
config BSP_USING_PWM1
bool "Enable GPT1 (32-Bits) output PWM"
default n
config BSP_USING_PWM2
bool "Enable GPT2 (32-Bits) output PWM"
default n
config BSP_USING_PWM3
bool "Enable GPT3 (32-Bits) output PWM"
default n
config BSP_USING_PWM4
bool "Enable GPT4 (16-Bits) output PWM"
default n
config BSP_USING_PWM5
bool "Enable GPT5 (16-Bits) output PWM"
default n
config BSP_USING_PWM6
bool "Enable GPT6 (16-Bits) output PWM"
default n
config BSP_USING_PWM7
bool "Enable GPT7 (16-Bits) output PWM"
default n
config BSP_USING_PWM8
bool "Enable GPT8 (16-Bits) output PWM"
default n
config BSP_USING_PWM9
bool "Enable GPT9 (16-Bits) output PWM"
default n
endif
menuconfig BSP_USING_CAN
bool "Enable CAN"
default n
select RT_USING_CAN
if BSP_USING_CAN
config BSP_USING_CAN0
bool "Enable CAN0"
default n
config BSP_USING_CAN1
bool "Enable CAN1"
default n
endif
endmenu
menu "Board extended module Drivers"
menuconfig BSP_USING_RW007
bool "Enable RW007"
default n
select PKG_USING_RW007
select BSP_USING_SPI
if BSP_USING_RW007
config RA_RW007_SPI_BUS_NAME
string "RW007 BUS NAME"
default "spi1"
config RA_RW007_CS_PIN
hex "(HEX)CS pin index"
default 0x040D
config RA_RW007_BOOT0_PIN
hex "(HEX)BOOT0 pin index (same as spi clk pin)"
default 0x040C
config RA_RW007_BOOT1_PIN
hex "(HEX)BOOT1 pin index (same as spi cs pin)"
default 0x040D
config RA_RW007_INT_BUSY_PIN
hex "(HEX)INT/BUSY pin index"
default 0x0506
config RA_RW007_RST_PIN
hex "(HEX)RESET pin index"
default 0x040F
endif
endmenu
endmenu