rt-thread-official/bsp/stm32/stm32f411-st-nucleo/board/Kconfig

192 lines
5.1 KiB
Plaintext

menu "Hardware Drivers Config"
config SOC_STM32F411RE
bool
select SOC_SERIES_STM32F4
select RT_USING_COMPONENTS_INIT
select RT_USING_USER_MAIN
default y
menu "Onboard Peripheral Drivers"
config BSP_USING_STLINK_TO_USART
bool "Enable STLINK TO USART (uart2)"
select BSP_USING_UART
select BSP_USING_UART2
default y
config BSP_USING_ARDUINO
bool "Compatible with Arduino Ecosystem (RTduino)"
select PKG_USING_RTDUINO
select BSP_USING_STLINK_TO_USART
select BSP_USING_GPIO
select BSP_USING_ADC
select BSP_USING_ADC1
select BSP_USING_PWM
select BSP_USING_PWM1
select BSP_USING_PWM4
select BSP_USING_PWM3
select BSP_USING_PWM2
select BSP_USING_PWM2_CH2
select BSP_USING_PWM3_CH1
select BSP_USING_PWM2_CH3
select BSP_USING_PWM3_CH2
select BSP_USING_PWM4_CH1
select BSP_USING_PWM1_CH1
select BSP_USING_I2C
select BSP_USING_I2C1
imply RTDUINO_USING_SERVO
imply RTDUINO_USING_WIRE
default n
endmenu
menu "On-chip Peripheral Drivers"
config BSP_USING_GPIO
bool "Enable GPIO"
select RT_USING_PIN
default y
menuconfig BSP_USING_UART
bool "Enable UART"
default y
select RT_USING_SERIAL
if BSP_USING_UART
config BSP_USING_UART2
bool "Enable UART2"
default y
config BSP_UART2_RX_USING_DMA
bool "Enable UART2 RX DMA"
depends on BSP_USING_UART2 && RT_SERIAL_USING_DMA
default n
config BSP_USING_UART6
bool "Enable UART6"
default y
config BSP_UART6_RX_USING_DMA
bool "Enable UART6 RX DMA"
depends on BSP_USING_UART6 && RT_SERIAL_USING_DMA
default n
endif
menuconfig BSP_USING_ADC
bool "Enable ADC"
default n
select RT_USING_ADC
if BSP_USING_ADC
config BSP_USING_ADC1
bool "Enable ADC1"
default n
endif
menuconfig BSP_USING_I2C1
bool "Enable I2C1 BUS (software simulation)"
default n
select RT_USING_I2C
select RT_USING_I2C_BITOPS
select RT_USING_PIN
if BSP_USING_I2C1
comment "Notice: PB8 --> 24; PB9 --> 25"
config BSP_I2C1_SCL_PIN
int "i2c1 scl pin number"
range 0 80
default 24
config BSP_I2C1_SDA_PIN
int "I2C1 sda pin number"
range 0 80
default 25
endif
menuconfig BSP_USING_PWM
bool "Enable PWM"
default n
select RT_USING_PWM
if BSP_USING_PWM
menuconfig BSP_USING_PWM1
bool "Enable timer1 output PWM"
default n
if BSP_USING_PWM1
config BSP_USING_PWM1_CH1
bool "Enable PWM1 channel1"
default n
endif
menuconfig BSP_USING_PWM2
bool "Enable timer2 output PWM"
default n
if BSP_USING_PWM2
config BSP_USING_PWM2_CH2
bool "Enable PWM2 channel2"
default n
config BSP_USING_PWM2_CH3
bool "Enable PWM2 channel3"
default n
endif
menuconfig BSP_USING_PWM3
bool "Enable timer3 output PWM"
default n
if BSP_USING_PWM3
config BSP_USING_PWM3_CH1
bool "Enable PWM3 channel1"
default n
config BSP_USING_PWM3_CH2
bool "Enable PWM3 channel2"
default n
config BSP_USING_PWM3_CH4
bool "Enable PWM3 channel4"
default n
endif
menuconfig BSP_USING_PWM4
bool "Enable timer4 output PWM"
default n
if BSP_USING_PWM4
config BSP_USING_PWM4_CH1
bool "Enable PWM4 channel1"
default n
endif
endif
menuconfig BSP_USING_ONCHIP_RTC
bool "Enable RTC"
select RT_USING_RTC
default n
if BSP_USING_ONCHIP_RTC
choice
prompt "Select clock source"
default BSP_RTC_USING_LSE
config BSP_RTC_USING_LSE
bool "RTC USING LSE"
config BSP_RTC_USING_LSI
bool "RTC USING LSI"
endchoice
endif
config BSP_USING_ON_CHIP_FLASH
bool "Enable on-chip FLASH"
default n
config BSP_USING_WDT
bool "Enable Watchdog Timer"
select RT_USING_WDT
default n
source "../libraries/HAL_Drivers/Kconfig"
endmenu
menu "Board extended module Drivers"
endmenu
endmenu