rt-thread-official/bsp/frdm-k64f/device/MK64F12/fsl_port.h

432 lines
16 KiB
C

/*
* Copyright (c) 2015, Freescale Semiconductor, Inc.
* Copyright 2016-2017 NXP
*
* Redistribution and use in source and binary forms, with or without modification,
* are permitted provided that the following conditions are met:
*
* o Redistributions of source code must retain the above copyright notice, this list
* of conditions and the following disclaimer.
*
* o Redistributions in binary form must reproduce the above copyright notice, this
* list of conditions and the following disclaimer in the documentation and/or
* other materials provided with the distribution.
*
* o Neither the name of the copyright holder nor the names of its
* contributors may be used to endorse or promote products derived from this
* software without specific prior written permission.
*
* THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS "AS IS" AND
* ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED
* WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE
* DISCLAIMED. IN NO EVENT SHALL THE COPYRIGHT HOLDER OR CONTRIBUTORS BE LIABLE FOR
* ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES
* (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES;
* LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND ON
* ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT
* (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE OF THIS
* SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.
*/
#ifndef _FSL_PORT_H_
#define _FSL_PORT_H_
#include "fsl_common.h"
/*!
* @addtogroup port
* @{
*/
/*******************************************************************************
* Definitions
******************************************************************************/
/*! @name Driver version */
/*@{*/
/*! Version 2.0.2. */
#define FSL_PORT_DRIVER_VERSION (MAKE_VERSION(2, 0, 2))
/*@}*/
#if defined(FSL_FEATURE_PORT_HAS_PULL_ENABLE) && FSL_FEATURE_PORT_HAS_PULL_ENABLE
/*! @brief Internal resistor pull feature selection */
enum _port_pull
{
kPORT_PullDisable = 0U, /*!< Internal pull-up/down resistor is disabled. */
kPORT_PullDown = 2U, /*!< Internal pull-down resistor is enabled. */
kPORT_PullUp = 3U, /*!< Internal pull-up resistor is enabled. */
};
#endif /* FSL_FEATURE_PORT_HAS_PULL_ENABLE */
#if defined(FSL_FEATURE_PORT_HAS_SLEW_RATE) && FSL_FEATURE_PORT_HAS_SLEW_RATE
/*! @brief Slew rate selection */
enum _port_slew_rate
{
kPORT_FastSlewRate = 0U, /*!< Fast slew rate is configured. */
kPORT_SlowSlewRate = 1U, /*!< Slow slew rate is configured. */
};
#endif /* FSL_FEATURE_PORT_HAS_SLEW_RATE */
#if defined(FSL_FEATURE_PORT_HAS_OPEN_DRAIN) && FSL_FEATURE_PORT_HAS_OPEN_DRAIN
/*! @brief Open Drain feature enable/disable */
enum _port_open_drain_enable
{
kPORT_OpenDrainDisable = 0U, /*!< Open drain output is disabled. */
kPORT_OpenDrainEnable = 1U, /*!< Open drain output is enabled. */
};
#endif /* FSL_FEATURE_PORT_HAS_OPEN_DRAIN */
#if defined(FSL_FEATURE_PORT_HAS_PASSIVE_FILTER) && FSL_FEATURE_PORT_HAS_PASSIVE_FILTER
/*! @brief Passive filter feature enable/disable */
enum _port_passive_filter_enable
{
kPORT_PassiveFilterDisable = 0U, /*!< Passive input filter is disabled. */
kPORT_PassiveFilterEnable = 1U, /*!< Passive input filter is enabled. */
};
#endif
#if defined(FSL_FEATURE_PORT_HAS_DRIVE_STRENGTH) && FSL_FEATURE_PORT_HAS_DRIVE_STRENGTH
/*! @brief Configures the drive strength. */
enum _port_drive_strength
{
kPORT_LowDriveStrength = 0U, /*!< Low-drive strength is configured. */
kPORT_HighDriveStrength = 1U, /*!< High-drive strength is configured. */
};
#endif /* FSL_FEATURE_PORT_HAS_DRIVE_STRENGTH */
#if defined(FSL_FEATURE_PORT_HAS_PIN_CONTROL_LOCK) && FSL_FEATURE_PORT_HAS_PIN_CONTROL_LOCK
/*! @brief Unlock/lock the pin control register field[15:0] */
enum _port_lock_register
{
kPORT_UnlockRegister = 0U, /*!< Pin Control Register fields [15:0] are not locked. */
kPORT_LockRegister = 1U, /*!< Pin Control Register fields [15:0] are locked. */
};
#endif /* FSL_FEATURE_PORT_HAS_PIN_CONTROL_LOCK */
#if defined(FSL_FEATURE_PORT_PCR_MUX_WIDTH) && FSL_FEATURE_PORT_PCR_MUX_WIDTH
/*! @brief Pin mux selection */
typedef enum _port_mux
{
kPORT_PinDisabledOrAnalog = 0U, /*!< Corresponding pin is disabled, but is used as an analog pin. */
kPORT_MuxAsGpio = 1U, /*!< Corresponding pin is configured as GPIO. */
kPORT_MuxAlt2 = 2U, /*!< Chip-specific */
kPORT_MuxAlt3 = 3U, /*!< Chip-specific */
kPORT_MuxAlt4 = 4U, /*!< Chip-specific */
kPORT_MuxAlt5 = 5U, /*!< Chip-specific */
kPORT_MuxAlt6 = 6U, /*!< Chip-specific */
kPORT_MuxAlt7 = 7U, /*!< Chip-specific */
kPORT_MuxAlt8 = 8U, /*!< Chip-specific */
kPORT_MuxAlt9 = 9U, /*!< Chip-specific */
kPORT_MuxAlt10 = 10U, /*!< Chip-specific */
kPORT_MuxAlt11 = 11U, /*!< Chip-specific */
kPORT_MuxAlt12 = 12U, /*!< Chip-specific */
kPORT_MuxAlt13 = 13U, /*!< Chip-specific */
kPORT_MuxAlt14 = 14U, /*!< Chip-specific */
kPORT_MuxAlt15 = 15U, /*!< Chip-specific */
} port_mux_t;
#endif /* FSL_FEATURE_PORT_PCR_MUX_WIDTH */
/*! @brief Configures the interrupt generation condition. */
typedef enum _port_interrupt
{
kPORT_InterruptOrDMADisabled = 0x0U, /*!< Interrupt/DMA request is disabled. */
#if defined(FSL_FEATURE_PORT_HAS_DMA_REQUEST) && FSL_FEATURE_PORT_HAS_DMA_REQUEST
kPORT_DMARisingEdge = 0x1U, /*!< DMA request on rising edge. */
kPORT_DMAFallingEdge = 0x2U, /*!< DMA request on falling edge. */
kPORT_DMAEitherEdge = 0x3U, /*!< DMA request on either edge. */
#endif
#if defined(FSL_FEATURE_PORT_HAS_IRQC_FLAG) && FSL_FEATURE_PORT_HAS_IRQC_FLAG
kPORT_FlagRisingEdge = 0x05U, /*!< Flag sets on rising edge. */
kPORT_FlagFallingEdge = 0x06U, /*!< Flag sets on falling edge. */
kPORT_FlagEitherEdge = 0x07U, /*!< Flag sets on either edge. */
#endif
kPORT_InterruptLogicZero = 0x8U, /*!< Interrupt when logic zero. */
kPORT_InterruptRisingEdge = 0x9U, /*!< Interrupt on rising edge. */
kPORT_InterruptFallingEdge = 0xAU, /*!< Interrupt on falling edge. */
kPORT_InterruptEitherEdge = 0xBU, /*!< Interrupt on either edge. */
kPORT_InterruptLogicOne = 0xCU, /*!< Interrupt when logic one. */
#if defined(FSL_FEATURE_PORT_HAS_IRQC_TRIGGER) && FSL_FEATURE_PORT_HAS_IRQC_TRIGGER
kPORT_ActiveHighTriggerOutputEnable = 0xDU, /*!< Enable active high-trigger output. */
kPORT_ActiveLowTriggerOutputEnable = 0xEU, /*!< Enable active low-trigger output. */
#endif
} port_interrupt_t;
#if defined(FSL_FEATURE_PORT_HAS_DIGITAL_FILTER) && FSL_FEATURE_PORT_HAS_DIGITAL_FILTER
/*! @brief Digital filter clock source selection */
typedef enum _port_digital_filter_clock_source
{
kPORT_BusClock = 0U, /*!< Digital filters are clocked by the bus clock. */
kPORT_LpoClock = 1U, /*!< Digital filters are clocked by the 1 kHz LPO clock. */
} port_digital_filter_clock_source_t;
/*! @brief PORT digital filter feature configuration definition */
typedef struct _port_digital_filter_config
{
uint32_t digitalFilterWidth; /*!< Set digital filter width */
port_digital_filter_clock_source_t clockSource; /*!< Set digital filter clockSource */
} port_digital_filter_config_t;
#endif /* FSL_FEATURE_PORT_HAS_DIGITAL_FILTER */
#if defined(FSL_FEATURE_PORT_PCR_MUX_WIDTH) && FSL_FEATURE_PORT_PCR_MUX_WIDTH
/*! @brief PORT pin configuration structure */
typedef struct _port_pin_config
{
#if defined(FSL_FEATURE_PORT_HAS_PULL_ENABLE) && FSL_FEATURE_PORT_HAS_PULL_ENABLE
uint16_t pullSelect : 2; /*!< No-pull/pull-down/pull-up select */
#else
uint16_t : 2;
#endif /* FSL_FEATURE_PORT_HAS_PULL_ENABLE */
#if defined(FSL_FEATURE_PORT_HAS_SLEW_RATE) && FSL_FEATURE_PORT_HAS_SLEW_RATE
uint16_t slewRate : 1; /*!< Fast/slow slew rate Configure */
#else
uint16_t : 1;
#endif /* FSL_FEATURE_PORT_HAS_SLEW_RATE */
uint16_t : 1;
#if defined(FSL_FEATURE_PORT_HAS_PASSIVE_FILTER) && FSL_FEATURE_PORT_HAS_PASSIVE_FILTER
uint16_t passiveFilterEnable : 1; /*!< Passive filter enable/disable */
#else
uint16_t : 1;
#endif /* FSL_FEATURE_PORT_HAS_PASSIVE_FILTER */
#if defined(FSL_FEATURE_PORT_HAS_OPEN_DRAIN) && FSL_FEATURE_PORT_HAS_OPEN_DRAIN
uint16_t openDrainEnable : 1; /*!< Open drain enable/disable */
#else
uint16_t : 1;
#endif /* FSL_FEATURE_PORT_HAS_OPEN_DRAIN */
#if defined(FSL_FEATURE_PORT_HAS_DRIVE_STRENGTH) && FSL_FEATURE_PORT_HAS_DRIVE_STRENGTH
uint16_t driveStrength : 1; /*!< Fast/slow drive strength configure */
#else
uint16_t : 1;
#endif
uint16_t : 1;
#if defined(FSL_FEATURE_PORT_PCR_MUX_WIDTH) && FSL_FEATURE_PORT_PCR_MUX_WIDTH
uint16_t mux : 3; /*!< Pin mux Configure */
#else
uint16_t : 3;
#endif
uint16_t : 4;
#if defined(FSL_FEATURE_PORT_HAS_PIN_CONTROL_LOCK) && FSL_FEATURE_PORT_HAS_PIN_CONTROL_LOCK
uint16_t lockRegister : 1; /*!< Lock/unlock the PCR field[15:0] */
#else
uint16_t : 1;
#endif /* FSL_FEATURE_PORT_HAS_PIN_CONTROL_LOCK */
} port_pin_config_t;
#endif /* FSL_FEATURE_PORT_PCR_MUX_WIDTH */
/*******************************************************************************
* API
******************************************************************************/
#if defined(__cplusplus)
extern "C" {
#endif
#if defined(FSL_FEATURE_PORT_PCR_MUX_WIDTH) && FSL_FEATURE_PORT_PCR_MUX_WIDTH
/*! @name Configuration */
/*@{*/
/*!
* @brief Sets the port PCR register.
*
* This is an example to define an input pin or output pin PCR configuration.
* @code
* // Define a digital input pin PCR configuration
* port_pin_config_t config = {
* kPORT_PullUp,
* kPORT_FastSlewRate,
* kPORT_PassiveFilterDisable,
* kPORT_OpenDrainDisable,
* kPORT_LowDriveStrength,
* kPORT_MuxAsGpio,
* kPORT_UnLockRegister,
* };
* @endcode
*
* @param base PORT peripheral base pointer.
* @param pin PORT pin number.
* @param config PORT PCR register configuration structure.
*/
static inline void PORT_SetPinConfig(PORT_Type *base, uint32_t pin, const port_pin_config_t *config)
{
assert(config);
uint32_t addr = (uint32_t)&base->PCR[pin];
*(volatile uint16_t *)(addr) = *((const uint16_t *)config);
}
/*!
* @brief Sets the port PCR register for multiple pins.
*
* This is an example to define input pins or output pins PCR configuration.
* @code
* // Define a digital input pin PCR configuration
* port_pin_config_t config = {
* kPORT_PullUp ,
* kPORT_PullEnable,
* kPORT_FastSlewRate,
* kPORT_PassiveFilterDisable,
* kPORT_OpenDrainDisable,
* kPORT_LowDriveStrength,
* kPORT_MuxAsGpio,
* kPORT_UnlockRegister,
* };
* @endcode
*
* @param base PORT peripheral base pointer.
* @param mask PORT pin number macro.
* @param config PORT PCR register configuration structure.
*/
static inline void PORT_SetMultiplePinsConfig(PORT_Type *base, uint32_t mask, const port_pin_config_t *config)
{
assert(config);
uint16_t pcrl = *((const uint16_t *)config);
if (mask & 0xffffU)
{
base->GPCLR = ((mask & 0xffffU) << 16) | pcrl;
}
if (mask >> 16)
{
base->GPCHR = (mask & 0xffff0000U) | pcrl;
}
}
/*!
* @brief Configures the pin muxing.
*
* @param base PORT peripheral base pointer.
* @param pin PORT pin number.
* @param mux pin muxing slot selection.
* - #kPORT_PinDisabledOrAnalog: Pin disabled or work in analog function.
* - #kPORT_MuxAsGpio : Set as GPIO.
* - #kPORT_MuxAlt2 : chip-specific.
* - #kPORT_MuxAlt3 : chip-specific.
* - #kPORT_MuxAlt4 : chip-specific.
* - #kPORT_MuxAlt5 : chip-specific.
* - #kPORT_MuxAlt6 : chip-specific.
* - #kPORT_MuxAlt7 : chip-specific.
* @Note : This function is NOT recommended to use together with the PORT_SetPinsConfig, because
* the PORT_SetPinsConfig need to configure the pin mux anyway (Otherwise the pin mux is
* reset to zero : kPORT_PinDisabledOrAnalog).
* This function is recommended to use to reset the pin mux
*
*/
static inline void PORT_SetPinMux(PORT_Type *base, uint32_t pin, port_mux_t mux)
{
base->PCR[pin] = (base->PCR[pin] & ~PORT_PCR_MUX_MASK) | PORT_PCR_MUX(mux);
}
#endif /* FSL_FEATURE_PORT_PCR_MUX_WIDTH */
#if defined(FSL_FEATURE_PORT_HAS_DIGITAL_FILTER) && FSL_FEATURE_PORT_HAS_DIGITAL_FILTER
/*!
* @brief Enables the digital filter in one port, each bit of the 32-bit register represents one pin.
*
* @param base PORT peripheral base pointer.
* @param mask PORT pin number macro.
*/
static inline void PORT_EnablePinsDigitalFilter(PORT_Type *base, uint32_t mask, bool enable)
{
if (enable == true)
{
base->DFER |= mask;
}
else
{
base->DFER &= ~mask;
}
}
/*!
* @brief Sets the digital filter in one port, each bit of the 32-bit register represents one pin.
*
* @param base PORT peripheral base pointer.
* @param config PORT digital filter configuration structure.
*/
static inline void PORT_SetDigitalFilterConfig(PORT_Type *base, const port_digital_filter_config_t *config)
{
assert(config);
base->DFCR = PORT_DFCR_CS(config->clockSource);
base->DFWR = PORT_DFWR_FILT(config->digitalFilterWidth);
}
#endif /* FSL_FEATURE_PORT_HAS_DIGITAL_FILTER */
/*@}*/
/*! @name Interrupt */
/*@{*/
/*!
* @brief Configures the port pin interrupt/DMA request.
*
* @param base PORT peripheral base pointer.
* @param pin PORT pin number.
* @param config PORT pin interrupt configuration.
* - #kPORT_InterruptOrDMADisabled: Interrupt/DMA request disabled.
* - #kPORT_DMARisingEdge : DMA request on rising edge(if the DMA requests exit).
* - #kPORT_DMAFallingEdge: DMA request on falling edge(if the DMA requests exit).
* - #kPORT_DMAEitherEdge : DMA request on either edge(if the DMA requests exit).
* - #kPORT_FlagRisingEdge : Flag sets on rising edge(if the Flag states exit).
* - #kPORT_FlagFallingEdge : Flag sets on falling edge(if the Flag states exit).
* - #kPORT_FlagEitherEdge : Flag sets on either edge(if the Flag states exit).
* - #kPORT_InterruptLogicZero : Interrupt when logic zero.
* - #kPORT_InterruptRisingEdge : Interrupt on rising edge.
* - #kPORT_InterruptFallingEdge: Interrupt on falling edge.
* - #kPORT_InterruptEitherEdge : Interrupt on either edge.
* - #kPORT_InterruptLogicOne : Interrupt when logic one.
* - #kPORT_ActiveHighTriggerOutputEnable : Enable active high-trigger output (if the trigger states exit).
* - #kPORT_ActiveLowTriggerOutputEnable : Enable active low-trigger output (if the trigger states exit).
*/
static inline void PORT_SetPinInterruptConfig(PORT_Type *base, uint32_t pin, port_interrupt_t config)
{
base->PCR[pin] = (base->PCR[pin] & ~PORT_PCR_IRQC_MASK) | PORT_PCR_IRQC(config);
}
/*!
* @brief Reads the whole port status flag.
*
* If a pin is configured to generate the DMA request, the corresponding flag
* is cleared automatically at the completion of the requested DMA transfer.
* Otherwise, the flag remains set until a logic one is written to that flag.
* If configured for a level sensitive interrupt that remains asserted, the flag
* is set again immediately.
*
* @param base PORT peripheral base pointer.
* @return Current port interrupt status flags, for example, 0x00010001 means the
* pin 0 and 16 have the interrupt.
*/
static inline uint32_t PORT_GetPinsInterruptFlags(PORT_Type *base)
{
return base->ISFR;
}
/*!
* @brief Clears the multiple pin interrupt status flag.
*
* @param base PORT peripheral base pointer.
* @param mask PORT pin number macro.
*/
static inline void PORT_ClearPinsInterruptFlags(PORT_Type *base, uint32_t mask)
{
base->ISFR = mask;
}
/*@}*/
#if defined(__cplusplus)
}
#endif
/*! @}*/
#endif /* _FSL_PORT_H_ */