libs/rt-thread-official
libs
/
rt-thread-official
mirror of https://github.com/RT-Thread/rt-thread.git
4
0
Fork 0
Code Issues Releases Wiki Activity
rt-thread-official/bsp/nuvoton/numaker-pfm-m487
History
Wayne Lin 7566c1a24c Update drivers. 
1. Improve LVGL avg FPS.
2. Sync configuration to 4.1.0.
 		2022-01-06 11:41:55 +08:00
..
applications Support LVGLv81 RTT music demo for N9H30 and NUC980. 2021-12-30 01:39:17 +08:00
board [armclang] 使用__clang__代替__CLANG_ARM 2021-12-29 14:15:38 -05:00
linking_scripts Update nuvoton porting. 2020-12-21 14:57:09 +08:00
.config Update drivers. 2022-01-06 11:41:55 +08:00
Kconfig Support Nuvoton NuMaker-IOT-M487 and NuMaker-PFM-M487 boards. 2020-06-17 16:30:11 +08:00
Nu_Link_Driver.ini Support Nuvoton NuMaker-IOT-M487 and NuMaker-PFM-M487 boards. 2020-06-17 16:30:11 +08:00
README.md Update nuvoton porting. 2020-12-21 14:57:09 +08:00
SConscript Support Nuvoton NuMaker-IOT-M487 and NuMaker-PFM-M487 boards. 2020-06-17 16:30:11 +08:00
SConstruct [update] CFLAGS 2021-12-17 14:28:40 +08:00
rtconfig.py Add compiling option for building time. 2020-06-24 00:32:10 +08:00
template.ewd Support Nuvoton NuMaker-IOT-M487 and NuMaker-PFM-M487 boards. 2020-06-17 16:30:11 +08:00
template.ewp Support Nuvoton NuMaker-IOT-M487 and NuMaker-PFM-M487 boards. 2020-06-17 16:30:11 +08:00
template.eww Support Nuvoton NuMaker-IOT-M487 and NuMaker-PFM-M487 boards. 2020-06-17 16:30:11 +08:00
template.uvproj Support Nuvoton NuMaker-IOT-M487 and NuMaker-PFM-M487 boards. 2020-06-17 16:30:11 +08:00
template.uvprojx Support Nuvoton NuMaker-IOT-M487 and NuMaker-PFM-M487 boards. 2020-06-17 16:30:11 +08:00

README.md

NuMaker-PFM-M487

1. Introduction

NuMaker-PFM-M487 provides multiple networking, interfaces, audio recording, playback functions, and flexible extended data storage.

NuMaker-PFM-M487

1.1 MCU specification

Features
MCU M487JIDAE
Operation frequency 192MHz
embedded Flash size 512kB, Dual Bank
SRAM size 160kB
Crypto engine DES, AES, ECC, 3DES, HMAC and SHA crypto accelerator
RMII interface Support 10/100 Mbps Ethernet

1.2 Interface

Interface
Arduino UNO
RJ45 Ethernet
USB 1.1/2.0 OTG ports
A microSD slot
A 3.5mm Audio connector

1.3 On-board devices

Device Description Driver supporting status
SPI flash W25Q32 Supported
Ethernet PHY IP101GR Supported
Audio Codec NAU88L25, Supports MIC and earphone Supported

2. Supported compiler

Support GCC, MDK4, MDK5, IAR IDE/compilers. More information of these compiler version as following:

IDE/Compiler Tested version
MDK4 4.76
MDK5 5.26.2
IAR 8.2
GCC GCC 5.4.1 20160919 (release)

Notice: Please install Nu-Link_Keil_Driver or Nu-Link_IAR_Driver for development.

3. Program firmware

Step 1:

At first, you need to configure ISW1 switch on the NuMaker-PFM-M487 board. Set the four switches to ‘ON’ position. After the configuration is done, connect the NuMaker-PFM-M487 board and your computer using the USB Micro cable. After that, window manager will show a ‘NuMicro MCU’ virtual disk. Finally, you will use this virtual disk to burn firmware.

NuLinkMe

NuMicro MCU

Step 2:

A simple firmware burning method is that you can drag and drop the binary image file to NuMicro MCU virtual disk or copy the binary file to NuMicro MCU disk to burn firmware.

CopyTo

4. Test

You can use Tera Term terminate emulator (or other software) to type commands of RTT. All parameters of serial communication are shown in below image. Here, you can find out the corresponding port number of Nuvoton Virtual Com Port in window device manager.

Serial settings

5. Purchase

6. Resources