libs/rt-thread-official
libs
/
rt-thread-official
mirror of https://github.com/RT-Thread/rt-thread.git
4
0
Fork 0
Code Issues Releases Wiki Activity
rt-thread-official/bsp/apollo2/libraries/drivers/hal/am_hal_flash.c

1491 lines
50 KiB
C
Raw Blame History

//*****************************************************************************
//
// am_hal_flash.c
//! @file
//!
//! @brief Functions for performing Flash operations.
//!
//! @addtogroup flash2 Flash
//! @ingroup apollo2hal
//!
//! IMPORTANT: Interrupts are active during execution of all HAL flash
//! functions. If an interrupt occurs during execution of a flash function
//! that programs or erases flash or INFO space, errors will occur if the
//! interrupt service routine (ISR) is located in on-chip flash.
//! If interrupts are expected during execution of a flash function that
//! programs or erases either flash or INFO space:
//! - Interrupts must be disabled via a critical section handler prior to
//! calling the flash function.
//! - Alternatively, applicable ISRs must be located in non-flash address space
//! (i.e. SRAM, off-chip ROM, etc.).
//!
//! @{
//
//*****************************************************************************
//*****************************************************************************
//
// Copyright (c) 2017, Ambiq Micro
// All rights reserved.
//
// Redistribution and use in source and binary forms, with or without
// modification, are permitted provided that the following conditions are met:
//
// 1. Redistributions of source code must retain the above copyright notice,
// this list of conditions and the following disclaimer.
//
// 2. Redistributions in binary form must reproduce the above copyright
// notice, this list of conditions and the following disclaimer in the
// documentation and/or other materials provided with the distribution.
//
// 3. Neither the name of the copyright holder nor the names of its
// contributors may be used to endorse or promote products derived from this
// software without specific prior written permission.
//
// THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS "AS IS"
// AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE
// IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE
// ARE DISCLAIMED. IN NO EVENT SHALL THE COPYRIGHT HOLDER OR CONTRIBUTORS BE
// LIABLE FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR
// CONSEQUENTIAL DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF
// SUBSTITUTE GOODS OR SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS
// INTERRUPTION) HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN
// CONTRACT, STRICT LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE)
// ARISING IN ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE
// POSSIBILITY OF SUCH DAMAGE.
//
// This is part of revision 1.2.11 of the AmbiqSuite Development Package.
//
//*****************************************************************************
#include <stdint.h>
#include <stdbool.h>
#include "am_mcu_apollo.h"
//
// Look-up table
//
g_am_hal_flash_t g_am_hal_flash =
{
//
// The basics.
//
// flash_mass_erase()
((int (*) (uint32_t, uint32_t)) 0x0800004d),
// flash_page_erase()
((int (*) (uint32_t, uint32_t, uint32_t)) 0x08000051),
// flash_program_main()
((int (*) (uint32_t, uint32_t *, uint32_t *, uint32_t)) 0x08000055),
// flash_program_info()
((int (*) (uint32_t, uint32_t, uint32_t *, uint32_t, uint32_t)) 0x08000059),
//
// Non-blocking variants, but be careful these are not interrupt safe so
// mask interrupts while these very long operations proceed.
//
// flash_mass_erase_nb()
((int (*)(uint32_t, uint32_t)) 0x0800006d),
// flash_page_erase_nb()
((int (*)(uint32_t, uint32_t, uint32_t)) 0x08000071),
// flash_nb_operation_complete()
((bool (*)(void)) 0x0800007d),
//
// Essentially these are recovery options.
//
// flash_erase_info()
((int (*)(uint32_t, uint32_t)) 0x08000081),
// flash_erase_main_plus_info()
((int (*)(uint32_t, uint32_t)) 0x08000089),
// flash_erase_main_plus_info_both_instances()
((int (*)(uint32_t)) 0x08000091),
// flash_recovery()
((void (*)(uint32_t)) 0x08000099),
//
// Useful utilities.
//
// flash_util_read_word()
((uint32_t (*)(uint32_t*)) 0x08000075),
// flash_util_write_word()
((void (*)(uint32_t*, uint32_t)) 0x08000079),
// delay_cycles()
((void (*)(uint32_t)) 0x0800009d),
//
// The following functions pointers must never be called from user
// programs. They are here primarily to document these entry points
// which are usable from a debugger or debugger script.
//
// flash_program_main_sram()
((void (*) (void)) 0x0800005d),
// flash_program_info_sram()
((void (*) (void)) 0x08000061),
// flash_erase_main_pages_sram()
((void (*) (void)) 0x08000065),
// flash_mass_erase_sram()
((void (*) (void)) 0x08000069),
// flash_erase_info_sram()
((void (*)(void)) 0x08000085),
// flash_erase_main_plus_info_sram()
((void (*)(void)) 0x0800008d)
};
//*****************************************************************************
//
//! @brief This function performs a mass erase on a flash instance.
//!
//! @param ui32Value - The flash program key.
//! @param ui32FlashInst - The flash instance to erase.
//!
//! This function will erase the desired instance of flash.
//!
//! @note For Apollo2, each flash instance contains a maximum of 512KB.
//!
//! @note Interrupts are active during execution of this function. Any interrupt
//! taken could cause execution errors. Please see the IMPORTANT note under
//! Detailed Description above for more details.
//!
//! @return 0 for success, non-zero for failure.
//
//*****************************************************************************
int
am_hal_flash_mass_erase(uint32_t ui32Value, uint32_t ui32FlashInst)
{
return g_am_hal_flash.flash_mass_erase(ui32Value, ui32FlashInst);
}
//*****************************************************************************
//
//! @brief This function performs a page erase on a flash instance.
//!
//! @param ui32Value - The flash program key.
//! @param ui32FlashInst - The flash instance to reference the page number with.
//! @param ui32PageNum - The flash page relative to the specified instance.
//!
//! This function will erase the desired flash page in the desired instance of
//! flash.
//!
//! @note For Apollo2, each flash page is 8KB (or AM_HAL_FLASH_PAGE_SIZE).
//! Each flash instance contains a maximum of 64 pages (or
//! AM_HAL_FLASH_INSTANCE_PAGES).
//!
//! @note When given an absolute flash address, a couple of helpful macros can
//! be utilized when calling this function.
//! For example:
//! am_hal_flash_page_erase(AM_HAL_FLASH_PROGRAM_KEY,
//! AM_HAL_FLASH_ADDR2INST(ui32Addr),
//! AM_HAL_FLASH_ADDR2PAGE(ui32Addr) );
//!
//! @note Interrupts are active during execution of this function. Any interrupt
//! taken could cause execution errors. Please see the IMPORTANT note under
//! Detailed Description above for more details.
//!
//! @return 0 for success, non-zero for failure.
//
//*****************************************************************************
int
am_hal_flash_page_erase(uint32_t ui32Value, uint32_t ui32FlashInst,
uint32_t ui32PageNum)
{
return g_am_hal_flash.flash_page_erase(ui32Value,
ui32FlashInst,
ui32PageNum);
}
//*****************************************************************************
//
//! @brief This programs up to N words of the Main array on one flash instance.
//!
//! @param ui32Value - The programming key, AM_HAL_FLASH_PROGRAM_KEY.
//! @param pui32Src - Pointer to word aligned array of data to program into
//! the flash instance.
//! @param pui32Dst - Pointer to the word aligned flash location where
//! programming of the flash instance is to begin.
//! @param ui32NumWords - The number of words to be programmed.
//!
//! This function will program multiple words in main flash.
//!
//! @note Interrupts are active during execution of this function. Any interrupt
//! taken could cause execution errors. Please see the IMPORTANT note under
//! Detailed Description above for more details.
//!
//! @return 0 for success, non-zero for failure.
//
//*****************************************************************************
int
am_hal_flash_program_main(uint32_t ui32Value, uint32_t *pui32Src,
uint32_t *pui32Dst, uint32_t ui32NumWords)
{
return g_am_hal_flash.flash_program_main(ui32Value, pui32Src,
pui32Dst, ui32NumWords);
}
//*****************************************************************************
//
//! @brief This function programs multiple words in the customer INFO space.
//!
//! @param ui32Value - The customer INFO space key.
//! @param ui32InfoInst - The INFO space instance, 0 or 1.
//! @param *pui32Src - Pointer to word aligned array of data to program into
//! the customer INFO space.
//! @param ui32Offset - Word offset into customer INFO space (offset of 0 is
//! the first word, 1 is second word, etc.).
//! @param ui32NumWords - The number of words to be programmed, must not
//! exceed AM_HAL_FLASH_INFO_SIZE/4.
//!
//! This function will program multiple words in the customer INFO space.
//!
//! @note Interrupts are active during execution of this function. Any interrupt
//! taken could cause execution errors. Please see the IMPORTANT note under
//! Detailed Description above for more details.
//!
//! @return 0 for success, non-zero for failure.
//
//*****************************************************************************
int
am_hal_flash_program_info(uint32_t ui32Value, uint32_t ui32InfoInst,
uint32_t *pui32Src, uint32_t ui32Offset,
uint32_t ui32NumWords)
{
return g_am_hal_flash.flash_program_info(ui32Value, 0, pui32Src,
ui32Offset, ui32NumWords);
}
//*****************************************************************************
//
//! @brief This function erases an instance of the customer INFO space.
//!
//! @param ui32ProgramKey - The customer INFO space programming key
//! (AM_HAL_FLASH_PROGRAM_KEY).
//! @param ui32Inst - The flash instance, either 0 or 1.
//!
//! This function will erase the the customer INFO space of the specified
//! instance.
//!
//! @note Interrupts are active during execution of this function. Any interrupt
//! taken could cause execution errors. Please see the IMPORTANT note under
//! Detailed Description above for more details.
//!
//! @return 0 for success, non-zero for failure.
//
//*****************************************************************************
int
am_hal_flash_erase_info(uint32_t ui32ProgramKey,
uint32_t ui32Inst)
{
return g_am_hal_flash.flash_erase_info(ui32ProgramKey, ui32Inst);
}
//*****************************************************************************
//
//! @brief This function erases the main instance + the customer INFO space.
//!
//! @param ui32ProgramKey - The customer INFO space key.
//! @param ui32Inst - The flash instance, either 0 or 1.
//!
//! This function will erase the main flash + the customer INFO space of the
//! specified instance.
//!
//! @note Interrupts are active during execution of this function. Any interrupt
//! taken could cause execution errors. Please see the IMPORTANT note under
//! Detailed Description above for more details.
//!
//! @return 0 for success, non-zero for failure.
//
//*****************************************************************************
int
am_hal_flash_erase_main_plus_info(uint32_t ui32ProgramKey,
uint32_t ui32Inst)
{
return g_am_hal_flash.flash_erase_main_plus_info(ui32ProgramKey,
ui32Inst);
}
//*****************************************************************************
//
//! @brief This function erases the main flash + the customer INFO space.
//!
//! @param ui32ProgramKey - The customer INFO space key.
//!
//! This function will erase both instances the main flash + the
//! customer INFO space.
//!
//! @note Interrupts are active during execution of this function. Any interrupt
//! taken could cause execution errors. Please see the IMPORTANT note under
//! Detailed Description above for more details.
//!
//! @return 0 for success, non-zero for failure.
//
//*****************************************************************************
int
am_hal_flash_erase_main_plus_info_both_instances(uint32_t ui32ProgramKey)
{
return g_am_hal_flash.flash_erase_main_plus_info_both_instances(
ui32ProgramKey);
}
//*****************************************************************************
//
//! @brief This function erases both main flash instances + both customer INFO
//! space instances.
//!
//! @param ui32RecoveryKey - The recovery key.
//!
//! This function erases both main instances and both customer INFOinstances
//! even if the customer INFO space is programmed to not be erasable. This
//! function completely erases the flash main and info instances and wipes the
//! SRAM. Upon completion of the erasure operations, it does a POI (power on
//! initialization) reset.
//!
//! @note Interrupts are active during execution of this function. Any interrupt
//! taken could cause execution errors. Please see the IMPORTANT note under
//! Detailed Description above for more details.
//!
//! @return Never Returns!!!
//
//*****************************************************************************
void
am_hal_flash_recovery(uint32_t ui32RecoveryKey)
{
g_am_hal_flash.flash_recovery(ui32RecoveryKey);
}
//*****************************************************************************
//
//! @brief Return ui32 value obtained from anywhere in D Code or System Bus
//!
//! @param ui32Address - return the value corresponding to this location.
//!
//! Use this function to read a value from various peripheral locations
//! that must be read from code running external to flash.
//!
//! @return the value found
//
//*****************************************************************************
uint32_t
am_hal_flash_load_ui32(uint32_t ui32Address)
{
return g_am_hal_flash.flash_util_read_word((uint32_t*)ui32Address);
}
//*****************************************************************************
//
//! @brief Use the bootrom to write to a location in SRAM or the system bus.
//!
//! @param ui32Address - Store the data value corresponding to this location.
//! @param ui32Data - 32-bit Data to be stored.
//!
//! Use this function to store a value to various peripheral or SRAM locations
//! that can not be touched from code running in SRAM or FLASH. There is no
//! known need for this function in Apollo2 at this time.
//!
//! @return None.
//
//*****************************************************************************
void
am_hal_flash_store_ui32(uint32_t ui32Address, uint32_t ui32Data)
{
g_am_hal_flash.flash_util_write_word((uint32_t*)ui32Address,
ui32Data);
}
//*****************************************************************************
//
//! @brief Use the bootrom to implement a spin loop.
//!
//! @param ui32Iterations - Number of iterations to delay.
//!
//! Use this function to implement a CPU busy waiting spin loop without cache
//! or delay uncertainties.
//!
//! Note that the ROM-based function executes at 3 cycles per iteration plus
//! the regular function call, entry, and exit overhead.
//! The call and return overhead, including the call to this function, is
//! somewhere in the neighborhood of 14 cycles, or 4.7 iterations.
//!
//! Example:
//! - MCU operating at 48MHz -> 20.83 ns / cycle
//! - Therefore each iteration (once inside the bootrom function) will consume
//! 62.5ns.
//! - The total overhead (assuming 14 cycles) is 292ns.
//! - For ui32Iterations=28: Total delay time = 0.292 + (0.0625 * 28) = 2.04us.
//!
//! The FLASH_CYCLES_US(n) macro can be used with am_hal_flash_delay() to
//! get an approximate microsecond delay.
//! e.g. For a 2us delay, use:
//! am_hal_flash_delay( FLASH_CYCLES_US(2) );
//!
//! @note Interrupts are active during execution of this function. Therefore,
//! any interrupt taken will affect the delay timing.
//!
//! @return None.
//
//*****************************************************************************
void
am_hal_flash_delay(uint32_t ui32Iterations)
{
g_am_hal_flash.delay_cycles(ui32Iterations);
}
//*****************************************************************************
//
//! @brief Delays for a desired amount of cycles while also waiting for a
//! status change.
//!
//! @param ui32usMaxDelay - Maximum number of ~1uS delay loops.
//! @param ui32Address - Address of the register for the status change.
//! @param ui32Mask - Mask for the status change.
//! @param ui32Value - Target value for the status change.
//!
//! This function will delay for approximately the given number of microseconds
//! while checking for a status change, exiting when either the given time has
//! expired or the status change is detected.
//!
//! @returns 0 = timeout.
//! 1 = status change detected.
//
//*****************************************************************************
uint32_t
am_hal_flash_delay_status_change(uint32_t ui32usMaxDelay, uint32_t ui32Address,
uint32_t ui32Mask, uint32_t ui32Value)
{
while ( ui32usMaxDelay-- )
{
//
// Check the status
//
if ( ( AM_REGVAL(ui32Address) & ui32Mask ) == ui32Value )
{
return 1;
}
//
// Call the BOOTROM cycle function to delay for about 1 microsecond.
//
am_hal_flash_delay( FLASH_CYCLES_US(1) );
}
return 0;
} // am_hal_flash_delay_status_change()
//*****************************************************************************
//
//! @brief Static Helper Function to check customer info valid bits erasure.
//!
//! Use this function to test the state of the 128 valid bits at the beginning
//! of customer info space. If these are all erased then return true.
//!
//! @return true if the customer info bits are currently erased.
//
//*****************************************************************************
static bool
customer_info_signature_erased(void)
{
uint32_t *pui32Signature = (uint32_t *) AM_HAL_FLASH_INFO_ADDR;
return ( (pui32Signature[3] == 0xFFFFFFFF) &&
(pui32Signature[2] == 0xFFFFFFFF) &&
(pui32Signature[1] == 0xFFFFFFFF) &&
(pui32Signature[0] == 0xFFFFFFFF) ) ? true : false;
}
//*****************************************************************************
//
//! @brief Static Helper Function to set customer info valid bits
//!
//! Use this function to set the state of the 128 valid bits at the beginning
//! of customer info space. If these bits are not set correctly then the
//! customer protection bits in the INFO space will not be honored by the
//! hardware.
//!
//! @return Zero for success. Non-Zero for errors.
//
//*****************************************************************************
static int
customer_info_signature_set(void)
{
uint32_t ui32Valid[4];
int iRC;
//
// If they are already set then we are done.
//
if ( am_hal_flash_customer_info_signature_check() )
{
return 0;
}
//
// If they are not erased at this point we have an error.
//
if ( !customer_info_signature_erased() )
{
return (2 << 16);
}
//
// OK they need to be set so do it.
//
ui32Valid[3] = AM_HAL_FLASH_INFO_SIGNATURE3;
ui32Valid[2] = AM_HAL_FLASH_INFO_SIGNATURE2;
ui32Valid[1] = AM_HAL_FLASH_INFO_SIGNATURE1;
ui32Valid[0] = AM_HAL_FLASH_INFO_SIGNATURE0;
iRC = g_am_hal_flash.flash_program_info(AM_HAL_FLASH_PROGRAM_KEY,
0, // instance
ui32Valid, // source data
0, // offset
4); // number of words
return iRC | ((iRC) ? (1 << 16) : 0);
}
//*****************************************************************************
//
//! @brief Check that the customer info bits are valid.
//!
//! Use this function to test the state of the 128 valid bits at the beginning
//! of customer info space. If these are not set correctly then the customer
//! protection bits in the INFO space will not be honored by the hardware.
//!
//! @return true if valid.
//
//*****************************************************************************
bool
am_hal_flash_customer_info_signature_check(void)
{
uint32_t *pui32Signature = (uint32_t *)AM_HAL_FLASH_INFO_ADDR;
return ( (pui32Signature[3] == AM_HAL_FLASH_INFO_SIGNATURE3) &&
(pui32Signature[2] == AM_HAL_FLASH_INFO_SIGNATURE2) &&
(pui32Signature[1] == AM_HAL_FLASH_INFO_SIGNATURE1) &&
(pui32Signature[0] == AM_HAL_FLASH_INFO_SIGNATURE0) );
}
//*****************************************************************************
//
//! @brief INFO signature set.
//!
//! Use this function to set the state of the 128 valid bits at the beginning
//! of customer info space, if needed.
//!
//! @note Interrupts are active during execution of this function. Any interrupt
//! taken could cause execution errors. Please see the IMPORTANT note under
//! Detailed Description above for more details.
//!
//! @return Zero for success. Non-Zero for errors.
//
//*****************************************************************************
bool
am_hal_flash_info_signature_set(void)
{
//
// Check and set signature.
//
return customer_info_signature_set() ? false : true;
}
//*****************************************************************************
//
//! @brief Disable FLASH INFO space.
//!
//! Use this function to set the state of the 128 valid bits at the beginning
//! of customer info space, if needed. Then disable FLASH erasure.
//!
//! @note Interrupts are active during execution of this function. Any interrupt
//! taken could cause execution errors. Please see the IMPORTANT note under
//! Detailed Description above for more details.
//!
//! @return Zero for success. Non-Zero for errors.
//
//*****************************************************************************
int32_t
am_hal_flash_info_erase_disable(void)
{
int iRC;
uint32_t ui32SecurityValue;
//
// Security protection only works if the signature data is correct.
//
iRC = customer_info_signature_set();
if ( iRC )
{
return iRC;
}
//
// Clear bit in INFO space to disable erasure.
//
ui32SecurityValue = AM_REGVAL(AM_HAL_FLASH_INFO_SECURITY_ADDR) &
~AM_HAL_FLASH_INFO_SECURITY_ENINFOERASE_M;
//
// Now write the word to the flash INFO space.
//
return g_am_hal_flash.flash_program_info(
AM_HAL_FLASH_PROGRAM_KEY,
0, // instance
&ui32SecurityValue, // source data
AM_HAL_FLASH_INFO_SECURITY_O / 4, // word offset
1 ); // number of words
}
//*****************************************************************************
//
//! @brief Check for Disabled FLASH INFO space.
//!
//! Use this function to determine whether FLASH INFO erasure is disabled.
//!
//! @return true if FLASH INFO erase is disabled, otherwise false.
//
//*****************************************************************************
bool
am_hal_flash_info_erase_disable_check(void)
{
//
// If they are erased at this point then SRAM wipe can't be enabled.
//
if ( customer_info_signature_erased() )
{
return false;
}
//
// If they are not valid at this point then SRAM wipe can't be enabled.
//
if ( !am_hal_flash_customer_info_signature_check() )
{
return false;
}
//
// Looking good so far, now check the SRAM WIPE bit.
//
return AM_REGVAL(AM_HAL_FLASH_INFO_SECURITY_ADDR) &
AM_HAL_FLASH_INFO_SECURITY_ENINFOERASE_M ? false : true;
}
//*****************************************************************************
//
//! @brief Mask off 1 to 4 quadrants of FLASH INFO space for programming.
//!
//! Use this function to set the state of the 128 valid bits at the beginning
//! of customer info space, if needed. Then and the mask bits with the INFO
//! space programming disable bits.
//!
//! @param ui32Mask - A mask of the 4 quadrants of info space where
//! bit0 = First quadrant (first 2KB).
//! bit1 = Second quadrant (second 2KB).
//! bit2 = Third quadrant (third 2KB).
//! bit3 = Fourth quadrant (fourth 2KB).
//!
//! @note This function disables only, any quadrant already disabled is not
//! reenabled. That is, any ui32Mask bits specified as 0 are essentially nops.
//!
//! @note Interrupts are active during execution of this function. Any interrupt
//! taken could cause execution errors. Please see the IMPORTANT note under
//! Detailed Description above for more details.
//!
//! @return Zero for success. Non-Zero for errors.
//
//*****************************************************************************
int32_t
am_hal_flash_info_program_disable(uint32_t ui32Mask)
{
int iRC;
uint32_t ui32SecurityValue;
//
// Security protection only works if the signature data is correct.
//
iRC = customer_info_signature_set();
if ( iRC )
{
return iRC;
}
//
// Make sure we have a valid mask and get the mask into the correct position.
//
ui32Mask <<= AM_HAL_FLASH_INFO_SECURITY_ENINFOPRGM_S;
ui32Mask &= AM_HAL_FLASH_INFO_SECURITY_ENINFOPRGM_M;
//
// The security bit set to 1 enables programming, 0 disables programming.
//
ui32SecurityValue = AM_REGVAL(AM_HAL_FLASH_INFO_SECURITY_ADDR) & ~ui32Mask;
//
// Now write the word to the flash INFO space.
//
return g_am_hal_flash.flash_program_info(
AM_HAL_FLASH_PROGRAM_KEY,
0, // instance
&ui32SecurityValue, // source data
AM_HAL_FLASH_INFO_SECURITY_O / 4, // word offset
1 ); // number of words
}
//*****************************************************************************
//
//! @brief Return a mask specifying which quadrants of customer INFO space have
//! been disabled for programming.
//!
//! Use this function to determine whether programming of customer INFO space
//! has been disabled.
//!
//! @return A 4-bit mask of the disabled quadrants.
//! 0xFFFFFFFF indicates an error.
//! 0x0 indicates all customer INFO space programming is enabled.
//! 0xF indicates all customer INFO space programming is disabled.
//! bit0 indicates the first customer INFO space is disabled for programming.
//! bit1 indicates the second customer INFO space is disabled for programming.
//! bit2 indicates the third customer INFO space is disabled for programming.
//! bit3 indicates the fourth customer INFO space is disabled for programming.
//
//*****************************************************************************
uint32_t
am_hal_flash_info_program_disable_get(void)
{
//
// If they are erased at this point then SRAM wipe can't be enabled.
//
if ( customer_info_signature_erased() )
{
return 0xFFFFFFFF;
}
//
// If not valid at this point, then INFO programming can't be enabled.
//
if ( !am_hal_flash_customer_info_signature_check() )
{
return 0xFFFFFFFF;
}
//
// Looking good so far, now return a mask of the disabled bits.
//
return ((AM_REGVAL(AM_HAL_FLASH_INFO_SECURITY_ADDR) &
AM_HAL_FLASH_INFO_SECURITY_ENINFOPRGM_M) ^
AM_HAL_FLASH_INFO_SECURITY_ENINFOPRGM_M) >>
AM_HAL_FLASH_INFO_SECURITY_ENINFOPRGM_S;
}
//*****************************************************************************
//
//! @brief Enable FLASH debugger protection (FLASH gets wiped if a debugger is
//! connected).
//!
//! Use this function to set the state of the 128 valid bits at the beginning
//! of customer info space, if needed. Then set the FLASH wipe bit to zero.
//!
//! @note Interrupts are active during execution of this function. Any interrupt
//! taken could cause execution errors. Please see the IMPORTANT note under
//! Detailed Description above for more details.
//!
//! @return Zero for success. Non-Zero for errors.
//
//*****************************************************************************
int32_t
am_hal_flash_wipe_flash_enable(void)
{
int iRC;
uint32_t ui32SecurityValue;
//
// Security protection only works if the signature data is correct.
//
iRC = customer_info_signature_set();
if ( iRC )
{
return iRC;
}
//
// Clear the FLASH Wipe bit.
//
ui32SecurityValue = AM_REGVAL(AM_HAL_FLASH_INFO_SECURITY_ADDR) &
~AM_HAL_FLASH_INFO_SECURITY_FLASHWIPE_M;
//
// Now write the word to the flash INFO space.
//
return g_am_hal_flash.flash_program_info(
AM_HAL_FLASH_PROGRAM_KEY,
0, // instance
&ui32SecurityValue, // source data
AM_HAL_FLASH_INFO_SECURITY_O / 4, // word offset
1 ); // number of words
}
//*****************************************************************************
//
//! @brief check for FLASH wipe protection enabled.
//!
//! Use this function to determine if FLASH wipe protection is enabled.
//!
//! @return true if FLASH wipe protection is enabled, otherwise false.
//
//*****************************************************************************
bool
am_hal_flash_wipe_flash_enable_check(void)
{
//
// If they are erased at this point then flash wipe can't be enabled.
//
if ( customer_info_signature_erased() )
{
return false;
}
//
// If they are not valid at this point then flash wipe can't be enabled.
//
if ( !am_hal_flash_customer_info_signature_check() )
{
return false;
}
//
// Looking good so far, now check the Flash WIPE bit.
//
return AM_REGVAL(AM_HAL_FLASH_INFO_SECURITY_ADDR) &
AM_HAL_FLASH_INFO_SECURITY_FLASHWIPE_M ? false : true;
}
//*****************************************************************************
//
//! @brief Enable SRAM protection so SRAM gets wiped if a debgger is connected.
//!
//! Use this function to set the state of the 128 valid bits at the beginning
//! of customer info space, if needed. Then set the SRAM wipe bit to zero.
//!
//! @note Interrupts are active during execution of this function. Any interrupt
//! taken could cause execution errors. Please see the IMPORTANT note under
//! Detailed Description above for more details.
//!
//! @return Zero for success. Non-Zero for errors.
//
//*****************************************************************************
int32_t
am_hal_flash_wipe_sram_enable(void)
{
int iRC;
uint32_t ui32SecurityValue;
//
// Security protection only works if the signature data is correct.
//
iRC = customer_info_signature_set();
if ( iRC )
{
return iRC;
}
//
// Clear the SRAM Wipe bit.
//
ui32SecurityValue = AM_REGVAL(AM_HAL_FLASH_INFO_SECURITY_ADDR) &
~AM_HAL_FLASH_INFO_SECURITY_SRAMWIPE_M;
//
// Now write the word to the flash INFO space.
//
return g_am_hal_flash.flash_program_info(
AM_HAL_FLASH_PROGRAM_KEY,
0, // instance
&ui32SecurityValue, // source data
AM_HAL_FLASH_INFO_SECURITY_O / 4, // word offset
1 ); // number of words
}
//*****************************************************************************
//
//! @brief check for SRAM protection enabled.
//!
//! Use this function to determine if SRAM protection is enabled.
//!
//! @return true if SRAM wipe protection is enabled, otherwise false.
//
//*****************************************************************************
bool
am_hal_flash_wipe_sram_enable_check(void)
{
//
// If they are erased at this point then SRAM wipe can't be enabled.
//
if ( customer_info_signature_erased() )
{
return false;
}
//
// If they are not vale at this point then SRAM wipe can't be enabled.
//
if ( !am_hal_flash_customer_info_signature_check() )
{
return false;
}
//
// Looking good so far, now check the SRAM WIPE bit.
//
return AM_REGVAL(AM_HAL_FLASH_INFO_SECURITY_ADDR) &
AM_HAL_FLASH_INFO_SECURITY_SRAMWIPE_M ? false : true;
}
//*****************************************************************************
//
//! @brief Disable Output from ITM/SWO.
//!
//! Use this function to set the state of the 128 valid bits at the beginning
//! of customer info space, if needed. Set the SWO disable bit to zero.
//!
//! @note Interrupts are active during execution of this function. Any interrupt
//! taken could cause execution errors. Please see the IMPORTANT note under
//! Detailed Description above for more details.
//!
//! @return Zero for success. Non-Zero for errors.
//
//*****************************************************************************
int32_t
am_hal_flash_swo_disable(void)
{
int iRC;
uint32_t ui32SecurityValue;
//
// Security protection only works if the signature data is correct.
//
iRC = customer_info_signature_set();
if ( iRC )
{
return iRC;
}
//
// Clear the SWO bit.
//
ui32SecurityValue = AM_REGVAL(AM_HAL_FLASH_INFO_SECURITY_ADDR) &
~AM_HAL_FLASH_INFO_SECURITY_SWOCTRL_M;
//
// Now write the word to the flash INFO space.
//
return g_am_hal_flash.flash_program_info(
AM_HAL_FLASH_PROGRAM_KEY,
0, // instance
&ui32SecurityValue, // source data
AM_HAL_FLASH_INFO_SECURITY_O / 4, // word offset
1 ); // number of words
}
//*****************************************************************************
//
//! @brief check for SWO disabled.
//!
//! Use this function to determine if the SWO is disabled.
//!
//! @return true if the ITM/SWO is disabled, otherwise false.
//
//*****************************************************************************
bool
am_hal_flash_swo_disable_check(void)
{
//
// If they are erased at this point then SRAM wipe can't be enabled.
//
if ( customer_info_signature_erased() )
{
return false;
}
//
// If they are not vale at this point then SRAM wipe can't be enabled.
//
if ( !am_hal_flash_customer_info_signature_check() )
{
return false;
}
//
// Looking good so far, now check the SWO bit.
//
return AM_REGVAL(AM_HAL_FLASH_INFO_SECURITY_ADDR) &
AM_HAL_FLASH_INFO_SECURITY_SWOCTRL_M ? false : true;
}
//*****************************************************************************
//
//! @brief Disable Connections from a debugger on the SWD interface.
//!
//! Use this function to set the state of the 128 valid bits at the beginning
//! of customer info space, if needed. Set the debugger disable bit to zero.
//!
//! @note Interrupts are active during execution of this function. Any interrupt
//! taken could cause execution errors. Please see the IMPORTANT note under
//! Detailed Description above for more details.
//!
//! @return Zero for success. Non-Zero for errors.
//
//*****************************************************************************
int32_t
am_hal_flash_debugger_disable(void)
{
int iRC;
uint32_t ui32SecurityValue;
//
// Security protection only works if the signature data is correct.
//
iRC = customer_info_signature_set();
if ( iRC )
{
return iRC;
}
//
// Clear the DEBUGGER bit.
//
ui32SecurityValue = AM_REGVAL(AM_HAL_FLASH_INFO_SECURITY_ADDR) &
~AM_HAL_FLASH_INFO_SECURITY_DEBUGGERPROT_M;
//
// Now write the word to the flash INFO space.
//
return g_am_hal_flash.flash_program_info(
AM_HAL_FLASH_PROGRAM_KEY,
0, // instance
&ui32SecurityValue, // source data
AM_HAL_FLASH_INFO_SECURITY_O / 4, // word offset
1 ); // number of words
}
//*****************************************************************************
//
//! @brief check for debugger disabled.
//!
//! Use this function to determine if the debugger is disabled.
//!
//! @return true if the debugger is disabled, otherwise false.
//
//*****************************************************************************
bool
am_hal_flash_debugger_disable_check(void)
{
//
// If they are erased at this point then SRAM wipe can't be enabled.
//
if ( customer_info_signature_erased() )
{
return false;
}
//
// If they are not vale at this point then SRAM wipe can't be enabled.
//
if ( !am_hal_flash_customer_info_signature_check() )
{
return false;
}
//
// Looking good so far, now check the debugger disable bit.
//
return AM_REGVAL(AM_HAL_FLASH_INFO_SECURITY_ADDR) &
AM_HAL_FLASH_INFO_SECURITY_DEBUGGERPROT_M ? false : true;
}
//*****************************************************************************
//
//! @brief This static helper function generates a 64-bit protection mask.
//!
//! @param pui32StartAddress - Starting address in flash to begin protection.
//! @param pui32StopAddress - Ending address in flash to stop protection.
//!
//! This function computes a chunk map for the protection range.
//!
//! @return Inverse of the actual chunk mask. That is, chunks to be protected
//! are represented as 0 in the returned mask, while chunks to be left alone
//! are represented as 1. This value can therefore be directly ANDed with the
//! existing bits in INFO space.
//! Note that -1 is returned if input parameters are invalid - this return
//! value would indicate that no chunks are to be protected.
//!
//
//*****************************************************************************
static uint64_t
generate_chunk_mask(uint32_t *pui32StartAddress, uint32_t *pui32StopAddress)
{
uint32_t ui32ChunkStart, ui32ChunkStop;
uint32_t ui32Width;
uint64_t ui64Mask;
//
// Validate the address input parameters
//
if ( (pui32StartAddress > pui32StopAddress) ||
(pui32StopAddress > (uint32_t*)AM_HAL_FLASH_LARGEST_VALID_ADDR) )
{
//
// Argument error, return value to leave all chunks unprotected.
//
return 0xFFFFFFFFFFFFFFFF;
}
//
// Extract chunk related information
//
ui32ChunkStart = AM_HAL_FLASH_INFO_ADDR2CHUNK((uint32_t)pui32StartAddress);
ui32ChunkStop = AM_HAL_FLASH_INFO_ADDR2CHUNK((uint32_t)pui32StopAddress);
ui32Width = ui32ChunkStop - ui32ChunkStart + 1;
if ( ui32Width == 64 )
{
ui64Mask = (uint64_t)0xFFFFFFFFFFFFFFFFLLU;
}
else
{
ui64Mask = ( ((uint64_t)0x0000000000000001) << ui32Width) - 1;
ui64Mask <<= ui32ChunkStart;
}
//
// OK now return the chunk mask (inverted).
//
return ~ui64Mask;
}
//*****************************************************************************
//
//! @brief This function sets copy protection for a range of flash chunks.
//!
//! @param pui32StartAddress - Starting address in flash to begin protection.
//! @param pui32StopAddress - Ending address in flash to stop protection.
//!
//! This function will set copy protection bits for a range of flash chunks
//!
//! @note Each flash chunk contains 16KBytes and corresponds to one bit in
//! the protection register. Set the bit to zero to enable protection.
//!
//! @note Interrupts are active during execution of this function. Any interrupt
//! taken could cause execution errors. Please see the IMPORTANT note under
//! Detailed Description above for more details.
//!
//! @return
//! 0 for success.
//! 0x400000 if the protection bits were already programmed (mask the return
//! value with 0x3FFFFF to ignore this case and treat as success).
//! Otherwise, non-zero for failure.
//
//*****************************************************************************
int32_t
am_hal_flash_copy_protect_set(uint32_t *pui32StartAddress,
uint32_t *pui32StopAddress)
{
int iRC;
bool bModified = false;
uint64_t ui64Mask;
uint32_t ui32Work;
uint32_t ui32Protection[2];
uint32_t *pui32Protection = (uint32_t *)AM_HAL_FLASH_INFO_COPYPROT_ADDR;
//
// Extract chunk mask from parameters.
// Also checks parameter validity (returns -1 if bad parameters).
//
ui64Mask = generate_chunk_mask(pui32StartAddress, pui32StopAddress);
if ( ~ui64Mask == 0x0 )
{
return 0x100000;
}
//
// Go get the current settings for copy protection.
//
ui32Protection[0] = pui32Protection[0];
ui32Protection[1] = pui32Protection[1];
//
// AND mask off the necessary protection bits in the lower word.
//
ui32Work = (uint32_t)ui64Mask;
if ( ( ~ui32Work ) && ( ui32Work != ui32Protection[0] ) )
{
bModified = true;
ui32Protection[0] &= ui32Work;
iRC = g_am_hal_flash.flash_program_info(
AM_HAL_FLASH_PROGRAM_KEY,
0, // instance
&ui32Protection[0], // source data
(AM_HAL_FLASH_INFO_COPYPROT_O / 4) + 0, // word offset
1 ); // number of words
if ( iRC )
{
return iRC | 0x10000;
}
}
//
// AND mask off the necessary protection bits in the upper word.
//
ui32Work = (uint32_t)(ui64Mask >> 32);
if ( ( ~ui32Work ) && ( ui32Work != ui32Protection[1] ) )
{
bModified = true;
ui32Protection[1] &= ui32Work;
iRC = g_am_hal_flash.flash_program_info(
AM_HAL_FLASH_PROGRAM_KEY,
0, // instance
&ui32Protection[1], // source data
(AM_HAL_FLASH_INFO_COPYPROT_O / 4) + 1, // word offset
1 ); // number of words
if ( iRC )
{
return iRC | 0x20000;
}
}
if ( bModified )
{
return 0;
}
else
{
return 0x400000;
}
}
//*****************************************************************************
//
//! @brief This function checks copy protection for a range of flash chunks.
//!
//! @param pui32StartAddress - Starting address in flash.
//! @param pui32StopAddress - Ending address in flash.
//!
//! This function will check copy protection bits for a range of flash chunks
//! it expects all chunks in the range to be protected.
//!
//! @note Each flash chunk contains 16KBytes and corresponds to one bit in
//! the protection register. Set the bit to zero to enable protection.
//!
//! @return false for at least one chunk in the covered range is not protected,
//! and true if all chunks in the covered range are protected.
//!
//
//*****************************************************************************
bool
am_hal_flash_copy_protect_check(uint32_t *pui32StartAddress,
uint32_t *pui32StopAddress)
{
uint64_t ui64Mask;
uint32_t ui32Work;
uint32_t *pui32Protection = (uint32_t *)AM_HAL_FLASH_INFO_COPYPROT_ADDR;
//
// Extract chunk mask from parameters.
// Also checks parameter validity (returns -1 if bad parameters).
//
ui64Mask = generate_chunk_mask(pui32StartAddress, pui32StopAddress);
if ( ~ui64Mask == 0x0 )
{
return false;
}
//
// Now check the lower word of protection bits.
//
ui32Work = (uint32_t)ui64Mask;
if ( ~ui32Work & pui32Protection[0] )
{
return false;
}
//
// Now check the lower word of protection bits.
//
ui32Work = (uint32_t)(ui64Mask >> 32);
if ( ~ui32Work & pui32Protection[1] )
{
return false;
}
//
// If we get here, there are no unprotected chunks within specified range.
//
return true;
}
//*****************************************************************************
//
//! @brief This function sets write protection for a range of flash chunks.
//!
//! @param pui32StartAddress - Starting address in flash to begin protection.
//! @param pui32StopAddress - Ending address in flash to stop protection.
//!
//! This function will set write protection bits for a range of flash chunks
//!
//! @note Each flash chunk contains 16KBytes and corresponds to one bit in
//! the protection register. Set the bit to zero to enable protection.
//!
//! @note Interrupts are active during execution of this function. Any interrupt
//! taken could cause execution errors. Please see the IMPORTANT note under
//! Detailed Description above for more details.
//!
//! @return
//! 0 for success.
//! 0x400000 if the protection bits were already programmed (mask the return
//! value with 0x3FFFFF to ignore this case and treat as success).
//! Otherwise, non-zero for failure.
//
//*****************************************************************************
int32_t
am_hal_flash_write_protect_set(uint32_t *pui32StartAddress,
uint32_t *pui32StopAddress)
{
int iRC;
bool bModified = false;
uint64_t ui64Mask;
uint32_t ui32Work;
uint32_t ui32Protection[2];
uint32_t *pui32Protection = (uint32_t *)AM_HAL_FLASH_INFO_WRITPROT_ADDR;
//
// Extract chunk mask from parameters.
// Also checks parameter validity (returns -1 if bad parameters).
//
ui64Mask = generate_chunk_mask(pui32StartAddress, pui32StopAddress);
if ( ~ui64Mask == 0x0 )
{
return 0x100000;
}
//
// Go get the current settings for copy protection.
//
ui32Protection[0] = pui32Protection[0];
ui32Protection[1] = pui32Protection[1];
//
// AND mask off the necessary protection bits in the lower word.
//
ui32Work = (uint32_t)ui64Mask;
if ( ( ~ui32Work ) && ( ui32Work != ui32Protection[0] ) )
{
bModified = true;
ui32Protection[0] &= ui32Work;
iRC = g_am_hal_flash.flash_program_info(
AM_HAL_FLASH_PROGRAM_KEY,
0, // instance
&ui32Protection[0], // source data
(AM_HAL_FLASH_INFO_WRITPROT_O / 4) + 0, // word offset
1 ); // number of words
if ( iRC )
{
return iRC | 0x10000;
}
}
//
// AND mask off the necessary protection bits in the upper word.
//
ui32Work = (uint32_t)(ui64Mask >> 32);
if ( ( ~ui32Work ) && ( ui32Work != ui32Protection[1] ) )
{
bModified = true;
ui32Protection[1] &= ui32Work;
iRC = g_am_hal_flash.flash_program_info(
AM_HAL_FLASH_PROGRAM_KEY,
0, // instance
&ui32Protection[1], // source data
(AM_HAL_FLASH_INFO_WRITPROT_O / 4) + 1, // word offset
1 ); // number of words
if ( iRC )
{
return iRC | 0x20000;
}
}
if ( bModified )
{
return 0;
}
else
{
return 0x400000;
}
}
//*****************************************************************************
//
//! @brief This function checks write protection for a range of flash chunks.
//!
//! @param pui32StartAddress - Starting address in flash.
//! @param pui32StopAddress - Ending address in flash.
//!
//! This function will check write protection bits for a range of flash chunks
//! it expects all chunks in the range to be protected.
//!
//! @note Each flash chunk contains 16KBytes and corresponds to one bit in
//! the protection register. Set the bit to zero to enable protection.
//!
//! @return false for at least one chunk in the covered range is not protected,
//! and true if all chunks in the covered range are protected.
//!
//
//*****************************************************************************
bool
am_hal_flash_write_protect_check(uint32_t *pui32StartAddress,
uint32_t *pui32StopAddress)
{
uint64_t ui64Mask;
uint32_t ui32Work;
uint32_t *pui32Protection = (uint32_t *)AM_HAL_FLASH_INFO_WRITPROT_ADDR;
//
// Extract chunk mask from parameters.
// Also checks parameter validity (returns -1 if bad parameters).
//
ui64Mask = generate_chunk_mask(pui32StartAddress, pui32StopAddress);
if ( ~ui64Mask == 0x0 )
{
return false;
}
//
// Now check the lower word of protection bits.
//
ui32Work = (uint32_t)ui64Mask;
if ( ~ui32Work & pui32Protection[0] )
{
return false;
}
//
// Now check the lower word of protection bits.
//
ui32Work = (uint32_t)(ui64Mask >> 32);
if ( ~ui32Work & pui32Protection[1] )
{
return false;
}
//
// If we get here, there are no unprotected chunks within specified range.
//
return true;
}
//*****************************************************************************
//
// End Doxygen group.
//! @}
//
//*****************************************************************************
View Git Blame Copy Permalink