menu "Hardware Drivers Config" config BSP_USING_QSPIFLASH bool default n config SOC_MIMXRT1176DVMAA bool select SOC_MIMXRT1170_SERIES select BSP_USING_QSPIFLASH select RT_USING_COMPONENTS_INIT select RT_USING_USER_MAIN default y menu "On-chip Peripheral Drivers" config BSP_USING_DMA bool "Enable DMA" default n config BSP_USING_GPIO bool "Enable GPIO" select RT_USING_PIN default y config BSP_USING_RTC bool "Enable RTC" select RT_USING_RTC default n config BSP_USING_USB bool "Enable USB" select RT_USING_USB_HOST default n if BSP_USING_USB config BSP_USB0_HOST bool "Enable USB0" default n config BSP_USB1_HOST bool "Enable USB1" default n endif config BSP_USING_SDIO bool "Enable SDIO" select RT_USING_SDIO select RT_USING_DFS default n if BSP_USING_SDIO config CODE_STORED_ON_SDCARD bool "Enable Code STORED On SDCARD" default n help "SD CARD work as boot devive" endif menuconfig BSP_USING_LPUART bool "Enable UART" select RT_USING_SERIAL default y if BSP_USING_LPUART config BSP_USING_LPUART1 bool "Enable LPUART1" default y config BSP_LPUART1_RX_USING_DMA bool "Enable LPUART1 RX DMA" depends on BSP_USING_LPUART1 select BSP_USING_DMA select RT_SERIAL_USING_DMA default n config BSP_LPUART1_RX_DMA_CHANNEL depends on BSP_LPUART1_RX_USING_DMA int "Set LPUART1 RX DMA channel (0-32)" default 0 config BSP_LPUART1_TX_USING_DMA bool "Enable LPUART1 TX DMA" depends on BSP_USING_LPUART1 select BSP_USING_DMA select RT_SERIAL_USING_DMA default n config BSP_LPUART1_TX_DMA_CHANNEL depends on BSP_LPUART1_TX_USING_DMA int "Set LPUART1 TX DMA channel (0-32)" default 1 config BSP_USING_LPUART3 bool "Enable LPUART3" default n config BSP_LPUART3_RX_USING_DMA bool "Enable LPUART3 RX DMA" depends on BSP_USING_LPUART3 select BSP_USING_DMA select RT_SERIAL_USING_DMA default n config BSP_LPUART3_RX_DMA_CHANNEL depends on BSP_LPUART3_RX_USING_DMA int "Set LPUART3 RX DMA channel (0-32)" default 0 config BSP_LPUART3_TX_USING_DMA bool "Enable LPUART3 TX DMA" depends on BSP_USING_LPUART3 select BSP_USING_DMA select RT_SERIAL_USING_DMA default n config BSP_LPUART3_TX_DMA_CHANNEL depends on BSP_LPUART3_TX_USING_DMA int "Set LPUART3 TX DMA channel (0-32)" default 1 endif menuconfig BSP_USING_CAN bool "Enable CAN" select RT_USING_CAN default n if BSP_USING_CAN config BSP_USING_CAN3 bool "Enable FLEXCAN3" default n endif menuconfig BSP_USING_FLEXSPI bool "Enable FLEXSPI" default n if BSP_USING_FLEXSPI config BSP_USING_FLEXSPI1 bool "Enable FLEXSPI1" default n config BSP_USING_FLEXSPI2 bool "Enable FLEXSPI2" default n endif endmenu menu "Onboard Peripheral Drivers" config BSP_USING_SDRAM bool "Enable SDRAM" default n menuconfig BSP_USING_ETH bool "Enable Ethernet" select RT_USING_NETDEV select RT_USING_LWIP default n if BSP_USING_ETH config BSP_USING_PHY select RT_USING_PHY bool "Enable ethernet phy" default y if BSP_USING_PHY config PHY_USING_KSZ8081 bool "i.MX RT1176EVK uses ksz8081 phy" default y if PHY_USING_KSZ8081 config PHY_KSZ8081_ADDRESS int "Specify address of phy device" default 2 config PHY_RESET_KSZ8081_PORT int "indicate port of reset" default 6 config PHY_RESET_KSZ8081_PIN int "indicate pin of reset" default 12 config FSL_FEATURE_PHYKSZ8081_USE_RMII50M_MODE bool "Enable the PHY ksz8081 RMII50M mode" depends on PHY_USING_KSZ8081 default y endif endif if BSP_USING_PHY config PHY_USING_RTL8211F bool "i.MX RT1176EVK uses rtl8211f phy" default y if PHY_USING_RTL8211F config PHY_RTL8211F_ADDRESS int "Specify address of phy device" default 1 config PHY_RESET_RTL8211F_PORT int "indicate port of reset" default 5 config PHY_RESET_RTL8211F_PIN int "indicate pin of reset" default 14 endif endif endif menuconfig BSP_USING_FS bool "Enable File System" select RT_USING_DFS_DEVFS select RT_USING_DFS default n if BSP_USING_FS config BSP_USING_SDCARD_FATFS bool "Enable SDCARD (FATFS)" select BSP_USING_SDIO select RT_USING_DFS_ELMFAT default n endif endmenu menu "Board extended module Drivers" endmenu endmenu