menu "Hardware Drivers Config" config SOC_R7FA6M4AF bool select SOC_SERIES_R7FA6M3 select RT_USING_COMPONENTS_INIT select RT_USING_USER_MAIN default y menu "Onboard Peripheral Drivers" endmenu menu "On-chip Peripheral Drivers" source "../libraries/HAL_Drivers/Kconfig" menuconfig BSP_USING_UART bool "Enable UART" default y select RT_USING_SERIAL select RT_USING_SERIAL_V2 if BSP_USING_UART menuconfig BSP_USING_UART4 bool "Enable UART4" default n if BSP_USING_UART4 config BSP_UART4_RX_USING_DMA bool "Enable UART4 RX DMA" depends on BSP_USING_UART4 && RT_SERIAL_USING_DMA default n config BSP_UART4_TX_USING_DMA bool "Enable UART4 TX DMA" depends on BSP_USING_UART4 && RT_SERIAL_USING_DMA default n config BSP_UART4_RX_BUFSIZE int "Set UART4 RX buffer size" range 64 65535 depends on RT_USING_SERIAL_V2 default 256 config BSP_UART4_TX_BUFSIZE int "Set UART4 TX buffer size" range 0 65535 depends on RT_USING_SERIAL_V2 default 0 endif menuconfig BSP_USING_UART9 bool "Enable UART9" default n if BSP_USING_UART9 config BSP_UART9_RX_USING_DMA bool "Enable UART9 RX DMA" depends on BSP_USING_UART9 && RT_SERIAL_USING_DMA default n config BSP_UART9_TX_USING_DMA bool "Enable UART9 TX DMA" depends on BSP_USING_UART9 && RT_SERIAL_USING_DMA default n config BSP_UART9_RX_BUFSIZE int "Set UART9 RX buffer size" range 64 65535 depends on RT_USING_SERIAL_V2 default 256 config BSP_UART9_TX_BUFSIZE int "Set UART9 TX buffer size" range 0 65535 depends on RT_USING_SERIAL_V2 default 0 endif endif menuconfig BSP_USING_SCI_SPI bool "Enable SCI SPI BUS" default n select RT_USING_SPI if BSP_USING_SCI_SPI config BSP_USING_SCI_SPI0 bool "Enable SCI SPI0 BUS" default n config BSP_USING_SCI_SPI1 bool "Enable SCI SPI1 BUS" default n config BSP_USING_SCI_SPI2 bool "Enable SCI SPI2 BUS" default n config BSP_USING_SCI_SPI3 bool "Enable SCI SPI3 BUS" default n config BSP_USING_SCI_SPI6 bool "Enable SCI SPI6 BUS" default n endif menuconfig BSP_USING_SPI bool "Enable SPI BUS" default n select RT_USING_SPI if BSP_USING_SPI config BSP_USING_SPI0 bool "Enable SPI0 BUS" default n config BSP_USING_SPI1 bool "Enable SPI1 BUS" default n endif menuconfig BSP_USING_FS bool "Enable filesystem" default n if BSP_USING_FS config BSP_USING_SDCARD_FS bool "Enable SDCARD filesystem" select BSP_USING_SDHI select RT_USING_DFS_ELMFAT default n config BSP_USING_SPICARD_FS bool "Enable SPI FLASH filesystem" select BSP_USING_SPI select BSP_USING_SCI_SPI6 select RT_USING_SPI_MSD select RT_USING_DFS_ELMFAT default n endif menuconfig BSP_USING_SDHI bool "Enable SDHI" default n select RT_USING_SDIO select RT_USING_DFS select RT_LIBC_USING_FILEIO select RT_USING_POSIX_DEVIO if BSP_USING_SDHI config SDHI_USING_1_BIT bool "Use 1-bit Mode(4-bit when disable)" default y endif menuconfig BSP_USING_PWM bool "Enable PWM" default n select RT_USING_PWM if BSP_USING_PWM config BSP_USING_PWM12 bool "Enable GPT12 (16-Bits) output PWM" default n endif menuconfig BSP_USING_CAN bool "Enable CAN" default n select RT_USING_CAN if BSP_USING_CAN config BSP_USING_CAN0 bool "Enable CAN0" default n endif config BSP_USING_LCD bool "Enable LCD" select BSP_USING_GPIO default n config BSP_USING_SPI_LCD bool "Enable SPI LCD" select BSP_USING_GPIO select BSP_USING_SPI select BSP_USING_SPI0 default n config BSP_USING_G2D bool "Enable G2D" default n config BSP_USING_JPEG bool "Enable JPEG" default n config BSP_USING_ETH bool "Enable Ethernet" select RT_USING_SAL select RT_USING_LWIP select RT_USING_NETDEV default n menuconfig BSP_USING_LVGL bool "Enable LVGL for LCD" select PKG_USING_LVGL default n if BSP_USING_LVGL config BSP_USING_LCD_ILI9431 bool "Enable LVGL for LCD_ILI9431" select PKG_USING_ILI9341 select BSP_USING_SPI_LCD default n config BSP_USING_LCD_RGB bool "Enable LVGL for LCD_RGB565" select BSP_USING_LCD default n endif menuconfig BSP_USING_LVGL_DEMO bool "Enable LVGL demo for LCD" if BSP_USING_LVGL_DEMO choice prompt "choice lvgl demo" default BSP_USING_LVGL_MUSIC_DEMO config BSP_USING_LVGL_MUSIC_DEMO bool "Enable LVGL music demo" select PKG_USING_LV_MUSIC_DEMO config BSP_USING_LVGL_VIDEO_DEMO bool "Enable LVGL video demo" select BSP_USING_G2D select BSP_USING_JPEG endchoice endif endmenu menu "Board extended module Drivers" menuconfig BSP_USING_RW007 bool "Enable RW007" default n select PKG_USING_RW007 select BSP_USING_SCI_SPI select BSP_USING_SCI_SPI3 select RT_USING_MEMPOOL select RW007_NOT_USE_EXAMPLE_DRIVERS if BSP_USING_RW007 config RA_RW007_SPI_BUS_NAME string "RW007 BUS NAME" default "scpi3" config RA_RW007_CS_PIN hex "(HEX)CS pin index" default 0x0308 config RA_RW007_BOOT0_PIN hex "(HEX)BOOT0 pin index (same as spi clk pin)" default 0x030B config RA_RW007_BOOT1_PIN hex "(HEX)BOOT1 pin index (same as spi cs pin)" default 0x0308 config RA_RW007_INT_BUSY_PIN hex "(HEX)INT/BUSY pin index" default 0x000F config RA_RW007_RST_PIN hex "(HEX)RESET pin index" default 0x030C endif endmenu endmenu