menu "Hardware Drivers Config"

    menu "On-chip Peripheral Drivers"

        config BSP_USING_GPIO
            bool "Enable GPIO"
            select RT_USING_PIN
            default y

        menuconfig BSP_USING_UART
            bool "Enable UART"
            default y
            select RT_USING_SERIAL

            if BSP_USING_UART
                config BSP_USING_UART1
                    bool "Enable UART1"
                    default y

                config BSP_UART1_RX_USING_DMA
                    bool "Enable UART1 RX DMA"
                    depends on BSP_USING_UART1 && RT_SERIAL_USING_DMA
                    default n

                config BSP_USING_UART2
                    bool "Enable UART2"
                    default n

                config BSP_UART2_RX_USING_DMA
                    bool "Enable UART2 RX DMA"
                    depends on BSP_USING_UART2 && RT_SERIAL_USING_DMA
                    default n

                config BSP_USING_LPUART1
                    bool "Enable LPUART1"
                    default n

                config BSP_LPUART1_RX_USING_DMA
                    bool "Enable LPUART1 RX DMA"
                    depends on BSP_USING_LPUART1 && RT_SERIAL_USING_DMA
                    default n
            endif

            config BSP_USING_QSPI
                bool "Enable QSPI BUS"
                select RT_USING_QSPI
                select RT_USING_SPI
                default n

            config BSP_USING_ONCHIP_RTC
                bool "Enable RTC"
                select RT_USING_RTC
                default n

        source "$(BSP_DIR)/../libraries/HAL_Drivers/drivers/Kconfig"

    endmenu

    menu "Onboard Peripheral Drivers"

        config BSP_USING_SDRAM
            bool "Enable SDRAM"
            default n

        config BSP_USING_QSPI_FLASH
            bool "Enable QSPI FLASH (W25Q256 qspi)"
            select BSP_USING_QSPI
            select RT_USING_SFUD
            select RT_SFUD_USING_QSPI
            default n

        config BSP_USING_SDMMC
            bool "Enable SDMMC (SD card)"
            select RT_USING_SDIO
            select RT_USING_DFS
            select RT_USING_DFS_ELMFAT
            default n

        config BSP_USING_USBD
            bool "Enable OTGFS as USB device"
            select RT_USING_USB_DEVICE
            default n

        config BSP_USING_OV5640
            bool "Enable camera (ov5640)"
            select BSP_USING_DCMI
            select BSP_USING_I2C
            select BSP_USING_I2C1
            select BSP_USING_PWM
            select BSP_USING_PWM1
            select BSP_USING_PWM1_CH1
            default n

        config BSP_USING_DCMI
            bool "Enable DCMI"
            default n

        menuconfig BSP_USING_I2C
            bool "Enable I2C BUS (software simulation)"
            select RT_USING_I2C
            select RT_USING_I2C_BITOPS
            select RT_USING_PIN
            default n
            if BSP_USING_I2C
                menuconfig BSP_USING_I2C1
                    bool "Enable I2C1 BUS (software simulation)"
                    default n
                    if BSP_USING_I2C1
                        comment "Notice: PB8 --> 24; PB9 --> 25"
                        config BSP_I2C1_SCL_PIN
                            int "i2c1 scl pin number"
                            range 1 176
                            default 24
                        config BSP_I2C1_SDA_PIN
                            int "I2C1 sda pin number"
                            range 1 176
                            default 25
                    endif

                menuconfig BSP_USING_I2C2
                    bool "Enable I2C2 BUS (software simulation)"
                    default n
                    if BSP_USING_I2C2
                        comment "Notice: PB10 --> 26; PB11 --> 27"
                        config BSP_I2C2_SCL_PIN
                            int "i2c2 scl pin number"
                            range 1 176
                            default 26
                        config BSP_I2C2_SDA_PIN
                            int "I2C2 sda pin number"
                            range 1 176
                            default 27
                    endif
            endif

        menuconfig BSP_USING_PWM
            bool "Enable PWM"
            default n
            select RT_USING_PWM
            if BSP_USING_PWM
            menuconfig BSP_USING_PWM1
                bool "Enable timer1 output pwm"
                default n
                if BSP_USING_PWM1
                    config BSP_USING_PWM1_CH1
                        bool "Enable PWM1 channel1"
                        default n
                endif
            endif

    endmenu

endmenu