/* * Copyright (c) 2006-2022, RT-Thread Development Team * * SPDX-License-Identifier: Apache-2.0 * * Change Logs: * Date Author Notes * 2020-07-20 thread-liu the first version */ #include "board.h" #include "drv_config.h" #include #include "lwipopts.h" #include "drv_eth.h" #if defined(BSP_USING_GBE) //#define DRV_DEBUG //#define ETH_RX_DUMP //#define ETH_TX_DUMP #define LOG_TAG "drv.emac" #include #define MAX_ADDR_LEN 6 rt_base_t level; #define TX_ADD_BASE 0x2FFC3000 #define RX_ADD_BASE 0x2FFC5000 #define TX_DMA_ADD_BASE 0x2FFC7000 #define RX_DMA_ADD_BASE 0x2FFC7100 #if defined(__ICCARM__) /* transmit buffer */ #pragma location = TX_ADD_BASE static uint8_t txBuffer[ETH_TXBUFNB][ETH_TX_BUF_SIZE]; /* Receive buffer */ #pragma location = RX_ADD_BASE static uint8_t rxBuffer[ETH_RXBUFNB][ETH_RX_BUF_SIZE]; /* Transmit DMA descriptors */ #pragma location = TX_DMA_ADD_BASE static TxDmaDesc txDmaDesc[ETH_TXBUFNB]; /* Receive DMA descriptors */ #pragma location = RX_DMA_ADD_BASE static RxDmaDesc rxDmaDesc[ETH_RXBUFNB]; #elif defined(__CC_ARM) || defined(__CLANG_ARM) /* transmit buffer */ static uint8_t txBuffer[ETH_TXBUFNB][ETH_TX_BUF_SIZE] __attribute__((at(TX_ADD_BASE))); /* Receive buffer */ static uint8_t rxBuffer[ETH_RXBUFNB][ETH_RX_BUF_SIZE] __attribute__((at(RX_ADD_BASE))); /* Transmit DMA descriptors */ static TxDmaDesc txDmaDesc[ETH_TXBUFNB] __attribute__((at(TX_DMA_ADD_BASE))); /* Receive DMA descriptors */ static RxDmaDesc rxDmaDesc[ETH_RXBUFNB] __attribute__((at(RX_DMA_ADD_BASE))); #elif defined ( __GNUC__ ) /* transmit buffer */ static uint8_t txBuffer[ETH_TXBUFNB][ETH_TX_BUF_SIZE] __attribute__((at(TX_ADD_BASE))); /* Receive buffer */ static uint8_t rxBuffer[ETH_RXBUFNB][ETH_RX_BUF_SIZE] __attribute__((at(RX_ADD_BASE))); /* Transmit DMA descriptors */ static TxDmaDesc txDmaDesc[ETH_TXBUFNB] __attribute__((at(TX_DMA_ADD_BASE))); /* Receive DMA descriptors */ static RxDmaDesc rxDmaDesc[ETH_RXBUFNB] __attribute__((at(RX_DMA_ADD_BASE))); #endif //Current transmit descriptor static rt_uint8_t txIndex = 0; //Current receive descriptor static rt_uint8_t rxIndex = 0; /* eth */ static struct rt_event rx_event = {0}; #define ETH_TIME_OUT 100000 struct rt_stm32_eth { /* inherit from ethernet device */ struct eth_device parent; #ifndef PHY_USING_INTERRUPT_MODE rt_timer_t poll_link_timer; #endif /* interface address info, hw address */ rt_uint8_t dev_addr[MAX_ADDR_LEN]; /* eth speed */ uint32_t eth_speed; /* eth duplex mode */ uint32_t eth_mode; }; static struct rt_stm32_eth stm32_eth_device = {0}; #if defined(ETH_RX_DUMP) || defined(ETH_TX_DUMP) #define __is_print(ch) ((unsigned int)((ch) - ' ') < 127u - ' ') static void dump_hex(const rt_uint8_t *ptr, rt_size_t buflen) { unsigned char *buf = (unsigned char *)ptr; int i, j; for (i = 0; i < buflen; i += 16) { rt_kprintf("%08X: ", i); for (j = 0; j < 16; j++) if (i + j < buflen) rt_kprintf("%02X ", buf[i + j]); else rt_kprintf(" "); rt_kprintf(" "); for (j = 0; j < 16; j++) if (i + j < buflen) rt_kprintf("%c", __is_print(buf[i + j]) ? buf[i + j] : '.'); rt_kprintf("\n"); } } #endif static rt_err_t phy_write_reg(uint8_t phy_addr, uint8_t reg_addr, uint16_t reg_value) { uint32_t temp; volatile uint32_t tickstart = 0; /* Take care not to alter MDC clock configuration */ temp = ETH->MACMDIOAR & ETH_MACMDIOAR_CR; /* Set up a write operation */ temp |= ETH_MACMDIOAR_GOC_Val(1) | ETH_MACMDIOAR_GB; /* PHY address */ temp |= (phy_addr << 21) & ETH_MACMDIOAR_PA; /* Register address */ temp |= (reg_addr << 16) & ETH_MACMDIOAR_RDA; /* Data to be written in the PHY register */ ETH->MACMDIODR = reg_value & ETH_MACMDIODR_GD; /* Start a write operation */ ETH->MACMDIOAR = temp; /* Wait for the write to complete */ tickstart = rt_tick_get(); while((ETH->MACMDIOAR & ETH_MACMDIOAR_GB) != 0) { /* judge timeout */ if((rt_tick_get() - tickstart) > ETH_TIME_OUT) { LOG_E("PHY write reg %02x date %04x timeout!", reg_addr, reg_value); return RT_ETIMEOUT; } } return RT_EOK; } static uint16_t phy_read_reg(uint8_t phy_addr, uint8_t reg_addr) { uint16_t reg_value = 0; uint32_t status = 0; volatile uint32_t tickstart = 0; /* Take care not to alter MDC clock configuration */ status = ETH->MACMDIOAR & ETH_MACMDIOAR_CR; /* Set up a read operation */ status |= ETH_MACMDIOAR_GOC_Val(3) | ETH_MACMDIOAR_GB; /* PHY address */ status |= (phy_addr << 21) & ETH_MACMDIOAR_PA; /* Register address */ status |= (reg_addr << 16) & ETH_MACMDIOAR_RDA; /* Start a read operation */ ETH->MACMDIOAR = status; /* Wait for the read to complete */ tickstart = rt_tick_get(); while((ETH->MACMDIOAR & ETH_MACMDIOAR_GB) != 0) { /* judge timeout */ if((rt_tick_get() - tickstart) > ETH_TIME_OUT) { LOG_E("PHY read reg %02x timeout!", reg_addr); return RT_ETIMEOUT; } } /* Get register value */ reg_value = ETH->MACMDIODR & ETH_MACMDIODR_GD; return reg_value; } static rt_err_t update_mac_mode(void) { uint32_t status; /* Read current MAC configuration */ status = ETH->MACCR; if (stm32_eth_device.eth_speed & PHY_1000M) { status &= ~ETH_MACCR_PS; status &= ~ETH_MACCR_FES; } else if (stm32_eth_device.eth_speed & PHY_100M) { status |= ETH_MACCR_PS; status |= ETH_MACCR_FES; } /* 10M */ else { status |= ETH_MACCR_PS; status &= ~ETH_MACCR_FES; } if (stm32_eth_device.eth_mode & PHY_FULL_DUPLEX) { status |= ETH_MACCR_DM; } else { status &= ~ETH_MACCR_DM; } /* Update MAC configuration register */ ETH->MACCR = status; return RT_EOK; } static void HAL_ETH_MspInit(void) { GPIO_InitTypeDef GPIO_InitStruct = {0}; RCC_PeriphCLKInitTypeDef PeriphClkInit = {0}; if(IS_ENGINEERING_BOOT_MODE()) { /** Initializes the peripherals clock */ PeriphClkInit.PeriphClockSelection = RCC_PERIPHCLK_ETH; PeriphClkInit.EthClockSelection = RCC_ETHCLKSOURCE_PLL4; if (HAL_RCCEx_PeriphCLKConfig(&PeriphClkInit) != HAL_OK) { Error_Handler(); } } /* Enable SYSCFG clock */ __HAL_RCC_SYSCFG_CLK_ENABLE(); /* Enable GPIO clocks */ __HAL_RCC_GPIOA_CLK_ENABLE(); __HAL_RCC_GPIOB_CLK_ENABLE(); __HAL_RCC_GPIOC_CLK_ENABLE(); __HAL_RCC_GPIOD_CLK_ENABLE(); __HAL_RCC_GPIOE_CLK_ENABLE(); __HAL_RCC_GPIOG_CLK_ENABLE(); /* Select RGMII interface mode */ HAL_SYSCFG_ETHInterfaceSelect(SYSCFG_ETH_RGMII); /* Enable Ethernet MAC clock */ __HAL_RCC_ETH1MAC_CLK_ENABLE(); __HAL_RCC_ETH1TX_CLK_ENABLE(); __HAL_RCC_ETH1RX_CLK_ENABLE(); /**ETH1 GPIO Configuration PA1 ------> ETH1_RX_CLK PA2 ------> ETH1_MDIO PA7 ------> ETH1_RX_CTL PB0 ------> ETH1_RXD2 PB1 ------> ETH1_RXD3 PB11 ------> ETH1_TX_CTL PC1 ------> ETH1_MDC PC2 ------> ETH1_TXD2 PC4 ------> ETH1_RXD0 PC5 ------> ETH1_RXD1 PE2 ------> ETH1_TXD3 PG4 ------> ETH1_GTX_CLK PG5 ------> ETH1_CLK125 PG13 ------> ETH1_TXD0 PG14 ------> ETH1_TXD1 */ GPIO_InitStruct.Pin = GPIO_PIN_1|GPIO_PIN_2|GPIO_PIN_7; GPIO_InitStruct.Mode = GPIO_MODE_AF_PP; GPIO_InitStruct.Pull = GPIO_NOPULL; GPIO_InitStruct.Speed = GPIO_SPEED_FREQ_VERY_HIGH; GPIO_InitStruct.Alternate = GPIO_AF11_ETH; HAL_GPIO_Init(GPIOA, &GPIO_InitStruct); GPIO_InitStruct.Pin = GPIO_PIN_0|GPIO_PIN_1|GPIO_PIN_11; HAL_GPIO_Init(GPIOB, &GPIO_InitStruct); GPIO_InitStruct.Pin = GPIO_PIN_1|GPIO_PIN_2|GPIO_PIN_4|GPIO_PIN_5; HAL_GPIO_Init(GPIOC, &GPIO_InitStruct); GPIO_InitStruct.Pin = GPIO_PIN_2; HAL_GPIO_Init(GPIOE, &GPIO_InitStruct); GPIO_InitStruct.Pin = GPIO_PIN_4|GPIO_PIN_5|GPIO_PIN_13|GPIO_PIN_14; HAL_GPIO_Init(GPIOG, &GPIO_InitStruct); /* ETH interrupt Init */ HAL_NVIC_SetPriority(ETH1_IRQn, 0x01, 0x00); HAL_NVIC_EnableIRQ(ETH1_IRQn); /* Configure PHY_RST (PD10) */ GPIO_InitStruct.Pin = GPIO_PIN_10; GPIO_InitStruct.Mode = GPIO_MODE_OUTPUT_PP; GPIO_InitStruct.Pull = GPIO_PULLUP; GPIO_InitStruct.Speed = GPIO_SPEED_FREQ_LOW; HAL_GPIO_Init(GPIOD, &GPIO_InitStruct); /* Reset PHY transceiver */ HAL_GPIO_WritePin(GPIOD, GPIO_PIN_10, GPIO_PIN_RESET); rt_thread_mdelay(20); HAL_GPIO_WritePin(GPIOD, GPIO_PIN_10, GPIO_PIN_SET); rt_thread_mdelay(20); } static rt_err_t rt_stm32_eth_init(rt_device_t dev) { RT_ASSERT(dev != RT_NULL); rt_uint32_t status; int i = 0 ; volatile uint32_t tickstart = 0; uint8_t *macAddr = &stm32_eth_device.dev_addr[0]; /* Initialize RX/TX descriptor index */ rxIndex = txIndex = 0; HAL_ETH_MspInit(); /* Reset Ethernet MAC peripheral */ __HAL_RCC_ETH1MAC_FORCE_RESET(); __HAL_RCC_ETH1MAC_RELEASE_RESET(); /* Ethernet Software reset */ ETH->DMAMR |= ETH_DMAMR_SWR; /* Wait for the reset to complete */ tickstart = rt_tick_get(); while (READ_BIT(ETH->DMAMR, ETH_DMAMR_SWR)) { if(((HAL_GetTick() - tickstart ) > ETH_TIME_OUT)) { LOG_E("ETH software reset timeout!"); return RT_ERROR; } } /* Adjust MDC clock range depending on HCLK frequency */ ETH->MACMDIOAR = ETH_MACMDIOAR_CR_Val(5); /* Use default MAC configuration */ ETH->MACCR = ETH_MACCR_DO; /* Set the MAC address of the station */ ETH->MACA0LR = ((macAddr[3] << 24) | (macAddr[2] << 16) | (macAddr[1] << 8) | macAddr[0]); ETH->MACA0HR = ((macAddr[5] << 8) | macAddr[4]); /* The MAC supports 3 additional addresses for unicast perfect filtering */ ETH->MACA1LR = 0; ETH->MACA1HR = 0; ETH->MACA2LR = 0; ETH->MACA2HR = 0; ETH->MACA3LR = 0; ETH->MACA3HR = 0; /* Initialize hash table */ ETH->MACHT0R = 0; ETH->MACHT1R = 0; /* Configure the receive filter */ ETH->MACPFR = ETH_MACPFR_HPF | ETH_MACPFR_HMC; /* Disable flow control */ ETH->MACQ0TXFCR = 0; ETH->MACRXFCR = 0; /* Enable the first RX queue */ ETH->MACRXQC0R = ETH_MACRXQC0R_RXQ0EN_Val(1); /* Configure DMA operating mode */ ETH->DMAMR = ETH_DMAMR_INTM_Val(0) | ETH_DMAMR_PR_Val(0); /* Configure system bus mode */ ETH->DMASBMR |= ETH_DMASBMR_AAL; /* The DMA takes the descriptor table as contiguous */ ETH->DMAC0CR = ETH_DMAC0CR_DSL_Val(0); /* Configure TX features */ ETH->DMAC0TXCR = ETH_DMAC0TXCR_TXPBL_Val(1); /* Configure RX features */ ETH->DMAC0RXCR = ETH_DMAC0RXCR_RXPBL_Val(1) | ETH_DMAC0RXCR_RBSZ_Val(ETH_RX_BUF_SIZE); /* Enable store and forward mode for transmission */ ETH->MTLTXQ0OMR = ETH_MTLTXQ0OMR_TQS_Val(7) | ETH_MTLTXQ0OMR_TXQEN_Val(2) | ETH_MTLTXQ0OMR_TSF; /* Enable store and forward mode for reception */ ETH->MTLRXQ0OMR = ETH_MTLRXQ0OMR_RQS_Val(7) | ETH_MTLRXQ0OMR_RSF; /* Initialize TX DMA descriptor list */ for (i = 0; i < ETH_TXBUFNB; i++) { /* The descriptor is initially owned by the application */ txDmaDesc[i].tdes0 = 0; txDmaDesc[i].tdes1 = 0; txDmaDesc[i].tdes2 = 0; txDmaDesc[i].tdes3 = 0; } /* Initialize RX DMA descriptor list */ for (i = 0; i < ETH_RXBUFNB; i++) { /* The descriptor is initially owned by the DMA */ rxDmaDesc[i].rdes0 = (uint32_t)rxBuffer[i]; rxDmaDesc[i].rdes1 = 0; rxDmaDesc[i].rdes2 = 0; rxDmaDesc[i].rdes3 = ETH_RDES3_OWN | ETH_RDES3_IOC | ETH_RDES3_BUF1V; } /* Set Transmit Descriptor List Address Register */ ETH->DMAC0TXDLAR = (uint32_t)&txDmaDesc[0]; /* Length of the transmit descriptor ring */ ETH->DMAC0TXRLR = ETH_TXBUFNB - 1; /* Set Receive Descriptor List Address Register */ ETH->DMAC0RXDLAR = (uint32_t)&rxDmaDesc[0]; /* Length of the receive descriptor ring */ ETH->DMAC0RXRLR = ETH_RXBUFNB - 1; /* Prevent interrupts from being generated when the transmit statistic * counters reach half their maximum value */ ETH->MMCTXIMR = ETH_MMCTXIMR_TXLPITRCIM | ETH_MMCTXIMR_TXLPIUSCIM | ETH_MMCTXIMR_TXGPKTIM | ETH_MMCTXIMR_TXMCOLGPIM | ETH_MMCTXIMR_TXSCOLGPIM; /* Prevent interrupts from being generated when the receive statistic * counters reach half their maximum value */ ETH->MMCRXIMR = ETH_MMCRXIMR_RXLPITRCIM | ETH_MMCRXIMR_RXLPIUSCIM | ETH_MMCRXIMR_RXUCGPIM | ETH_MMCRXIMR_RXALGNERPIM | ETH_MMCRXIMR_RXCRCERPIM; /* Disable MAC interrupts */ ETH->MACIER = 0; /* Enable the desired DMA interrupts */ ETH->DMAC0IER = ETH_DMAC0IER_NIE | ETH_DMAC0IER_RIE | ETH_DMAC0IER_TIE; /* Enable MAC transmission and reception */ ETH->MACCR |= ETH_MACCR_TE | ETH_MACCR_RE; /* Enable DMA transmission and reception */ ETH->DMAC0TXCR |= ETH_DMAC0TXCR_ST; ETH->DMAC0RXCR |= ETH_DMAC0RXCR_SR; /* Reset PHY transceiver */ phy_write_reg(RTL8211E_PHY_ADDR, RTL8211E_BMCR, RTL8211E_BMCR_RESET); status = phy_read_reg(RTL8211E_PHY_ADDR, RTL8211E_BMCR); /* Wait for the reset to complete */ tickstart = rt_tick_get(); while (status & RTL8211E_BMCR_RESET) { if((rt_tick_get() - tickstart) > ETH_TIME_OUT) { LOG_E("PHY software reset timeout!"); return RT_ETIMEOUT; } else { status = phy_read_reg(RTL8211E_PHY_ADDR, RTL8211E_BMCR); } } /* The PHY will generate interrupts when link status changes are detected */ phy_write_reg(RTL8211E_PHY_ADDR, RTL8211E_INER, RTL8211E_INER_AN_COMPLETE | RTL8211E_INER_LINK_STATUS); return RT_EOK; } static rt_err_t rt_stm32_eth_open(rt_device_t dev, rt_uint16_t oflag) { LOG_D("emac open"); return RT_EOK; } static rt_err_t rt_stm32_eth_close(rt_device_t dev) { LOG_D("emac close"); return RT_EOK; } static rt_size_t rt_stm32_eth_read(rt_device_t dev, rt_off_t pos, void *buffer, rt_size_t size) { LOG_D("emac read"); rt_set_errno(-RT_ENOSYS); return 0; } static rt_size_t rt_stm32_eth_write(rt_device_t dev, rt_off_t pos, const void *buffer, rt_size_t size) { LOG_D("emac write"); rt_set_errno(-RT_ENOSYS); return 0; } static rt_err_t rt_stm32_eth_control(rt_device_t dev, int cmd, void *args) { switch (cmd) { case NIOCTL_GADDR: /* get mac address */ if (args) { rt_memcpy(args, stm32_eth_device.dev_addr, 6); } else { return -RT_ERROR; } break; default : break; } return RT_EOK; } rt_err_t rt_stm32_eth_tx(rt_device_t dev, struct pbuf *p) { uint32_t framelen = 0; struct pbuf *q = RT_NULL; /* Copy user data to the transmit buffer */ for (q = p; q != NULL; q = q->next) { /* Make sure the current buffer is available for writing */ if((txDmaDesc[txIndex].tdes3 & ETH_TDES3_OWN) != 0) { LOG_D("buffer not valid"); return ERR_USE; } level = rt_hw_interrupt_disable(); rt_memcpy(&txBuffer[txIndex][framelen], q->payload, q->len); framelen += q->len; rt_hw_interrupt_enable(level); /* Check the frame length */ if (framelen > ETH_TX_BUF_SIZE - 1) { LOG_D(" tx buffer frame length over : %d", framelen); return ERR_USE; } } #ifdef ETH_TX_DUMP rt_kprintf("Tx dump, len= %d\r\n", framelen); dump_hex(txBuffer[txIndex], framelen); #endif /* Set the start address of the buffer */ txDmaDesc[txIndex].tdes0 = (uint32_t)txBuffer[txIndex]; /* Write the number of bytes to send */ txDmaDesc[txIndex].tdes2 = ETH_TDES2_IOC | (framelen & ETH_TDES2_B1L); /* Give the ownership of the descriptor to the DMA */ txDmaDesc[txIndex].tdes3 = ETH_TDES3_OWN | ETH_TDES3_FD | ETH_TDES3_LD; /* Data synchronization barrier */ __DSB(); /* Clear TBU flag to resume processing */ ETH->DMAC0SR = ETH_DMAC0SR_TBU; /* Instruct the DMA to poll the transmit descriptor list */ ETH->DMAC0TXDTPR = 0; if (++txIndex > ETH_TXBUFNB - 1) { txIndex = 0; } return ERR_OK; } struct pbuf *rt_stm32_eth_rx(rt_device_t dev) { rt_uint32_t framelength = 0; uint32_t framelen = 0; struct pbuf *p = RT_NULL, *q = RT_NULL; /* The current buffer is available for reading */ if (!(rxDmaDesc[rxIndex].rdes3 & ETH_RDES3_OWN)) { /* FD and LD flags should be set */ if ((rxDmaDesc[rxIndex].rdes3 & ETH_RDES3_FD) && (rxDmaDesc[rxIndex].rdes3 & ETH_RDES3_LD)) { /* Make sure no error occurred */ if(!(rxDmaDesc[rxIndex].rdes3 & ETH_RDES3_ES)) { /* Retrieve the length of the frame */ framelength = rxDmaDesc[rxIndex].rdes3 & ETH_RDES3_PL; /* check the frame length */ framelength = (framelength > ETH_RX_BUF_SIZE) ? ETH_RX_BUF_SIZE : framelength; p = pbuf_alloc(PBUF_RAW, framelength, PBUF_RAM); if (p != NULL) { for (q = p; q != NULL; q = q->next) { level=rt_hw_interrupt_disable(); rt_memcpy(q->payload, &rxBuffer[rxIndex][framelen], q->len); framelen += q->len; rt_hw_interrupt_enable(level); if (framelen > framelength) { LOG_E("frame len is too long!"); return RT_NULL; } } } } else { /* The received packet contains an error */ LOG_D("the received packet contains an error!"); return RT_NULL; } } else { /* The packet is not valid */ LOG_D("the packet is not valid"); return RT_NULL; } /* Set the start address of the buffer */ rxDmaDesc[rxIndex].rdes0 = (uint32_t)rxBuffer[rxIndex]; /* Give the ownership of the descriptor back to the DMA */ rxDmaDesc[rxIndex].rdes3 = ETH_RDES3_OWN | ETH_RDES3_IOC | ETH_RDES3_BUF1V; #ifdef ETH_RX_DUMP rt_kprintf("Rx dump, len= %d\r\n", framelen); dump_hex(rxBuffer[rxIndex], framelen); #endif /* Increment index and wrap around if necessary */ if (++rxIndex > ETH_RXBUFNB - 1) { rxIndex = 0; } /* Clear RBU flag to resume processing */ ETH->DMAC0SR = ETH_DMAC0SR_RBU; /* Instruct the DMA to poll the receive descriptor list */ ETH->DMAC0RXDTPR = 0; } return p; } void ETH1_IRQHandler(void) { rt_uint32_t status = 0; /* enter interrupt */ rt_interrupt_enter(); /* Read DMA status register */ status = ETH->DMAC0SR; /* Frame transmitted */ if (status & ETH_DMAC0SR_TI) { /* Clear the Eth DMA Tx IT pending bits */ ETH->DMAC0SR = ETH_DMAC0SR_TI; } /* Frame received */ else if (status & ETH_DMAC0SR_RI) { /* Disable RIE interrupt */ ETH->DMAC0IER &= ~ETH_DMAC0IER_RIE; rt_event_send(&rx_event, status); } /* ETH DMA Error */ if (status & ETH_DMAC0SR_AIS) { ETH->DMAC0IER &= ~ETH_DMAC0IER_AIE; LOG_E("eth dam err"); } /* Clear the interrupt flags */ ETH->DMAC0SR = ETH_DMAC0SR_NIS; /* leave interrupt */ rt_interrupt_leave(); } static void phy_linkchange() { rt_uint32_t status = 0; /* Read status register to acknowledge the interrupt */ status = phy_read_reg(RTL8211E_PHY_ADDR, RTL8211E_INSR); if (status & (RTL8211E_INSR_AN_COMPLETE | RTL8211E_INSR_LINK_STATUS)) { status = phy_read_reg(RTL8211E_PHY_ADDR, RTL8211E_BMSR); status = phy_read_reg(RTL8211E_PHY_ADDR, RTL8211E_BMSR); if (status & RTL8211E_BMSR_LINK_STATUS) { LOG_D("link up"); status = phy_read_reg(RTL8211E_PHY_ADDR, RTL8211E_PHYSR); switch (status & RTL8211E_PHYSR_SPEED) { case RTL8211E_PHYSR_SPEED_10MBPS: { LOG_D("speed: 10M"); stm32_eth_device.eth_speed |= PHY_10M; break; } case RTL8211E_PHYSR_SPEED_100MBPS: { LOG_D("speed: 100M"); stm32_eth_device.eth_speed |= PHY_100M; break; } case RTL8211E_PHYSR_SPEED_1000MBPS: { LOG_D("speed: 1000M"); stm32_eth_device.eth_speed |= PHY_1000M; break; } /* Unknown speed */ default: rt_kprintf("Invalid speed."); break; } stm32_eth_device.eth_mode = (status & RTL8211E_PHYSR_DUPLEX)? PHY_FULL_DUPLEX : PHY_HALF_DUPLEX; update_mac_mode(); /* send link up. */ eth_device_linkchange(&stm32_eth_device.parent, RT_TRUE); } else { LOG_D("link down"); eth_device_linkchange(&stm32_eth_device.parent, RT_FALSE); } } } #ifdef PHY_USING_INTERRUPT_MODE static void eth_phy_isr(void *args) { rt_uint32_t status = 0; phy_read_reg(RTL8211E_PHY_ADDR, PHY_INTERRUPT_FLAG_REG, (uint32_t *)&status); LOG_D("phy interrupt status reg is 0x%X", status); phy_linkchange(); } #endif /* PHY_USING_INTERRUPT_MODE */ static void phy_monitor_thread_entry(void *parameter) { rt_uint32_t status = 0; phy_linkchange(); #ifdef PHY_USING_INTERRUPT_MODE /* configuration intterrupt pin */ rt_pin_mode(PHY_INT_PIN, PIN_MODE_INPUT_PULLUP); rt_pin_attach_irq(PHY_INT_PIN, PIN_IRQ_MODE_FALLING, eth_phy_isr, (void *)"callbackargs"); rt_pin_irq_enable(PHY_INT_PIN, PIN_IRQ_ENABLE); /* enable phy interrupt */ phy_write_reg(RTL8211E_PHY_ADDR, PHY_INTERRUPT_MASK_REG, PHY_INT_MASK); #if defined(PHY_INTERRUPT_CTRL_REG) phy_write_reg( RTL8211E_PHY_ADDR, PHY_INTERRUPT_CTRL_REG, PHY_INTERRUPT_EN); #endif #else /* PHY_USING_INTERRUPT_MODE */ stm32_eth_device.poll_link_timer = rt_timer_create("phylnk", (void (*)(void*))phy_linkchange, NULL, RT_TICK_PER_SECOND, RT_TIMER_FLAG_PERIODIC); if (!stm32_eth_device.poll_link_timer || rt_timer_start(stm32_eth_device.poll_link_timer) != RT_EOK) { LOG_E("Start link change detection timer failed"); } #endif /* PHY_USING_INTERRUPT_MODE */ while(1) { if (rt_event_recv(&rx_event, 0xffffffff, RT_EVENT_FLAG_OR | RT_EVENT_FLAG_CLEAR, RT_WAITING_FOREVER, &status) == RT_EOK) { /* check dma rx buffer */ if (ETH->DMAC0SR & ETH_DMAC0SR_RI) { /* Clear interrupt flag */ ETH->DMAC0SR = ETH_DMAC0SR_RI; /* Process all pending packets */ while (rxDmaDesc[rxIndex].rdes3 & ETH_RDES3_PL) { /* trigger lwip receive thread */ eth_device_ready(&(stm32_eth_device.parent)); } } /* enable DMA interrupts */ ETH->DMAC0IER = ETH_DMAC0IER_NIE | ETH_DMAC0IER_RIE | ETH_DMAC0IER_TIE; } } } /* Register the EMAC device */ static int rt_hw_stm32_eth_init(void) { rt_err_t state = RT_EOK; /* OUI 00-80-E1 STMICROELECTRONICS. */ stm32_eth_device.dev_addr[0] = 0x00; stm32_eth_device.dev_addr[1] = 0x80; stm32_eth_device.dev_addr[2] = 0xE1; /* generate MAC addr from 96bit unique ID. */ stm32_eth_device.dev_addr[3] = *(rt_uint8_t *)(UID_BASE + 4); stm32_eth_device.dev_addr[4] = *(rt_uint8_t *)(UID_BASE + 2); stm32_eth_device.dev_addr[5] = *(rt_uint8_t *)(UID_BASE + 0); stm32_eth_device.parent.parent.init = rt_stm32_eth_init; stm32_eth_device.parent.parent.open = rt_stm32_eth_open; stm32_eth_device.parent.parent.close = rt_stm32_eth_close; stm32_eth_device.parent.parent.read = rt_stm32_eth_read; stm32_eth_device.parent.parent.write = rt_stm32_eth_write; stm32_eth_device.parent.parent.control = rt_stm32_eth_control; stm32_eth_device.parent.parent.user_data = RT_NULL; stm32_eth_device.parent.eth_rx = rt_stm32_eth_rx; stm32_eth_device.parent.eth_tx = rt_stm32_eth_tx; rt_event_init(&rx_event, "eth_rx", RT_IPC_FLAG_FIFO); /* register eth device */ state = eth_device_init(&(stm32_eth_device.parent), "e0"); if (RT_EOK == state) { LOG_D("emac device init success"); } else { LOG_E("emac device init faild: %d", state); state = -RT_ERROR; } /* start phy monitor */ rt_thread_t tid; tid = rt_thread_create("phy", phy_monitor_thread_entry, RT_NULL, 1024, RT_THREAD_PRIORITY_MAX - 2, 2); if (tid != RT_NULL) { rt_thread_startup(tid); } else { state = -RT_ERROR; } return state; } INIT_DEVICE_EXPORT(rt_hw_stm32_eth_init); #endif