menu "Hardware Drivers Config"

config SOC_STM32H750VBT6
    bool
    select SOC_SERIES_STM32H7
    select RT_USING_COMPONENTS_INIT
    select RT_USING_USER_MAIN
    default y

menu "Onboard Peripheral Drivers"

    config BSP_USING_SPI_FLASH
        bool "Enable SPI FLASH (W25Q64 spi1)"
	    select BSP_USING_SPI
        select BSP_USING_SPI1
        select RT_USING_DFS
        select PKG_USING_LITTLEFS
        select RT_USING_MTD_NOR
        select RT_USING_FAL
        select FAL_USING_SFUD_PORT
        select RT_USING_SFUD
        select RT_SFUD_USING_SFDP
        default n

    config BSP_USING_QSPI_FLASH
        bool "Enable QSPI FLASH (W25Q64)"
        select BSP_USING_QSPI
        select FAL_USING_SFUD_PORT
        select RT_USING_SFUD
        select RT_SFUD_USING_QSPI
        default n

    config BSP_USING_LCD_SPI
        bool "Enable 0.96' TFT-LCD(ST7735S)"
        select BSP_USING_GPIO
        select BSP_USING_SPI
        select BSP_USING_SPI4
        # select BSP_SPI4_TX_USING_DMA
        select BSP_USING_PWM
        select BSP_USING_PWM1
        select BSP_USING_PWM1_CH2
        default n

        if BSP_USING_LCD_SPI
            choice
                prompt "choice back light"
                default LCD_BACKLIGHT_USING_GPIO
                config LCD_BACKLIGHT_USING_PWM
                    bool "LCD_BACKLIGHT_USING_PWM(tim1_ch2 pwm1)"
                config LCD_BACKLIGHT_USING_GPIO
                    bool "LCD_BACKLIGHT_USING_GPIO(PE10)"
            endchoice
        endif

endmenu

menu "On-chip Peripheral Drivers"

    config BSP_USING_GPIO
        bool "Enable GPIO"
        select RT_USING_PIN
        default y

    menuconfig BSP_USING_UART
        bool "Enable UART"
        default y
        select RT_USING_SERIAL
        if BSP_USING_UART
            config BSP_USING_UART1
                bool "Enable UART1"
                default y

            config BSP_UART1_RX_USING_DMA
                bool "Enable UART1 RX DMA"
                depends on BSP_USING_UART1 && RT_SERIAL_USING_DMA
                default n
        endif

    config BSP_USING_QSPI
        bool "Enable QSPI BUS"
        select RT_USING_QSPI
        select RT_USING_SPI
        default n

    menuconfig BSP_USING_SPI
        bool "Enable SPI BUS"
        default n
        select RT_USING_SPI
        if BSP_USING_SPI
            config BSP_USING_SPI1
                bool "Enable SPI1 BUS"
                default n

            config BSP_USING_SPI4
                bool "Enable SPI4 BUS"
                default n
        endif

    menuconfig BSP_USING_I2C1
        bool "Enable I2C1 BUS (software simulation)"
        default n
        select RT_USING_I2C
        select RT_USING_I2C_BITOPS
        select RT_USING_PIN
        if BSP_USING_I2C1
            config BSP_I2C1_SCL_PIN
                int "i2c1 scl pin number"
                range 1 216
                default 135
            config BSP_I2C1_SDA_PIN
                int "I2C1 sda pin number"
                range 1 216
                default 95
        endif

    menuconfig BSP_USING_PWM
        bool "Enable pwm"
        default n
        select RT_USING_PWM
        if BSP_USING_PWM
        menuconfig BSP_USING_PWM1
            bool "Enable timer1 output pwm"
            default n
            if BSP_USING_PWM1
                config BSP_USING_PWM1_CH1
                    bool "Enable PWM1 channel1"
                    default n

                config BSP_USING_PWM1_CH2
                    bool "Enable PWM1 channel2"
                    default n

                config BSP_USING_PWM1_CH3
                    bool "Enable PWM1 channel3"
                    default n

                config BSP_USING_PWM1_CH4
                    bool "Enable PWM1 channel4"
                    default n
            endif
        endif

    menuconfig BSP_USING_ADC
        bool "Enable ADC"
        default n
        select RT_USING_ADC
        if BSP_USING_ADC
            config BSP_USING_ADC1
                bool "Enable ADC1"
                default n

            config BSP_USING_ADC2
                bool "Enable ADC2"
                default n

            config BSP_USING_ADC3
                bool "Enable ADC3"
                default n
        endif

    config BSP_USING_ON_CHIP_FLASH
        bool "Enable on-chip FLASH"
        default n

    config BSP_USING_SDIO
        bool "Enable SDIO"
        select RT_USING_SDIO
        select RT_USING_DFS
        default n

    config BSP_USING_USBD
        bool "Enable OTGHS as USB device"
        select RT_USING_USB_DEVICE
        select BSP_USBD_TYPE_HS
        select BSP_USBD_SPEED_HS
        select BSP_USBD_PHY_ULPI
        default n

    source "../libraries/HAL_Drivers/Kconfig"

endmenu

menu "Board extended module Drivers"

endmenu

endmenu