/**************************************************************************//** * @file GPIO.h * @version V3.00 * @brief M480 series GPIO driver header file * * @copyright (C) 2016 Nuvoton Technology Corp. All rights reserved. ******************************************************************************/ #ifndef __GPIO_H__ #define __GPIO_H__ #ifdef __cplusplus extern "C" { #endif /** @addtogroup Standard_Driver Standard Driver @{ */ /** @addtogroup GPIO_Driver GPIO Driver @{ */ /** @addtogroup GPIO_EXPORTED_CONSTANTS GPIO Exported Constants @{ */ #define GPIO_PIN_MAX 16UL /*!< Specify Maximum Pins of Each GPIO Port \hideinitializer */ /*---------------------------------------------------------------------------------------------------------*/ /* GPIO_MODE Constant Definitions */ /*---------------------------------------------------------------------------------------------------------*/ #define GPIO_MODE_INPUT 0x0UL /*!< Input Mode \hideinitializer */ #define GPIO_MODE_OUTPUT 0x1UL /*!< Output Mode \hideinitializer */ #define GPIO_MODE_OPEN_DRAIN 0x2UL /*!< Open-Drain Mode \hideinitializer */ #define GPIO_MODE_QUASI 0x3UL /*!< Quasi-bidirectional Mode \hideinitializer */ /*---------------------------------------------------------------------------------------------------------*/ /* GPIO Interrupt Type Constant Definitions */ /*---------------------------------------------------------------------------------------------------------*/ #define GPIO_INT_RISING 0x00010000UL /*!< Interrupt enable by Input Rising Edge \hideinitializer */ #define GPIO_INT_FALLING 0x00000001UL /*!< Interrupt enable by Input Falling Edge \hideinitializer */ #define GPIO_INT_BOTH_EDGE 0x00010001UL /*!< Interrupt enable by both Rising Edge and Falling Edge \hideinitializer */ #define GPIO_INT_HIGH 0x01010000UL /*!< Interrupt enable by Level-High \hideinitializer */ #define GPIO_INT_LOW 0x01000001UL /*!< Interrupt enable by Level-Level \hideinitializer */ /*---------------------------------------------------------------------------------------------------------*/ /* GPIO_INTTYPE Constant Definitions */ /*---------------------------------------------------------------------------------------------------------*/ #define GPIO_INTTYPE_EDGE 0UL /*!< GPIO_INTTYPE Setting for Edge Trigger Mode \hideinitializer */ #define GPIO_INTTYPE_LEVEL 1UL /*!< GPIO_INTTYPE Setting for Edge Level Mode \hideinitializer */ /*---------------------------------------------------------------------------------------------------------*/ /* GPIO Slew Rate Type Constant Definitions */ /*---------------------------------------------------------------------------------------------------------*/ #define GPIO_SLEWCTL_NORMAL 0x0UL /*!< GPIO slew setting for normal Mode \hideinitializer */ #define GPIO_SLEWCTL_HIGH 0x1UL /*!< GPIO slew setting for high Mode \hideinitializer */ #define GPIO_SLEWCTL_FAST 0x2UL /*!< GPIO slew setting for fast Mode \hideinitializer */ /*---------------------------------------------------------------------------------------------------------*/ /* GPIO Pull-up And Pull-down Type Constant Definitions */ /*---------------------------------------------------------------------------------------------------------*/ #define GPIO_PUSEL_DISABLE 0x0UL /*!< GPIO PUSEL setting for Disable Mode \hideinitializer */ #define GPIO_PUSEL_PULL_UP 0x1UL /*!< GPIO PUSEL setting for Pull-up Mode \hideinitializer */ #define GPIO_PUSEL_PULL_DOWN 0x2UL /*!< GPIO PUSEL setting for Pull-down Mode \hideinitializer */ /*---------------------------------------------------------------------------------------------------------*/ /* GPIO_DBCTL Constant Definitions */ /*---------------------------------------------------------------------------------------------------------*/ #define GPIO_DBCTL_ICLK_ON 0x00000020UL /*!< GPIO_DBCTL setting for all IO pins edge detection circuit is always active after reset \hideinitializer */ #define GPIO_DBCTL_ICLK_OFF 0x00000000UL /*!< GPIO_DBCTL setting for edge detection circuit is active only if IO pin corresponding GPIOx_IEN bit is set to 1 \hideinitializer */ #define GPIO_DBCTL_DBCLKSRC_LIRC 0x00000010UL /*!< GPIO_DBCTL setting for de-bounce counter clock source is the internal 10 kHz \hideinitializer */ #define GPIO_DBCTL_DBCLKSRC_HCLK 0x00000000UL /*!< GPIO_DBCTL setting for de-bounce counter clock source is the HCLK \hideinitializer */ #define GPIO_DBCTL_DBCLKSEL_1 0x00000000UL /*!< GPIO_DBCTL setting for sampling cycle = 1 clocks \hideinitializer */ #define GPIO_DBCTL_DBCLKSEL_2 0x00000001UL /*!< GPIO_DBCTL setting for sampling cycle = 2 clocks \hideinitializer */ #define GPIO_DBCTL_DBCLKSEL_4 0x00000002UL /*!< GPIO_DBCTL setting for sampling cycle = 4 clocks \hideinitializer */ #define GPIO_DBCTL_DBCLKSEL_8 0x00000003UL /*!< GPIO_DBCTL setting for sampling cycle = 8 clocks \hideinitializer */ #define GPIO_DBCTL_DBCLKSEL_16 0x00000004UL /*!< GPIO_DBCTL setting for sampling cycle = 16 clocks \hideinitializer */ #define GPIO_DBCTL_DBCLKSEL_32 0x00000005UL /*!< GPIO_DBCTL setting for sampling cycle = 32 clocks \hideinitializer */ #define GPIO_DBCTL_DBCLKSEL_64 0x00000006UL /*!< GPIO_DBCTL setting for sampling cycle = 64 clocks \hideinitializer */ #define GPIO_DBCTL_DBCLKSEL_128 0x00000007UL /*!< GPIO_DBCTL setting for sampling cycle = 128 clocks \hideinitializer */ #define GPIO_DBCTL_DBCLKSEL_256 0x00000008UL /*!< GPIO_DBCTL setting for sampling cycle = 256 clocks \hideinitializer */ #define GPIO_DBCTL_DBCLKSEL_512 0x00000009UL /*!< GPIO_DBCTL setting for sampling cycle = 512 clocks \hideinitializer */ #define GPIO_DBCTL_DBCLKSEL_1024 0x0000000AUL /*!< GPIO_DBCTL setting for sampling cycle = 1024 clocks \hideinitializer */ #define GPIO_DBCTL_DBCLKSEL_2048 0x0000000BUL /*!< GPIO_DBCTL setting for sampling cycle = 2048 clocks \hideinitializer */ #define GPIO_DBCTL_DBCLKSEL_4096 0x0000000CUL /*!< GPIO_DBCTL setting for sampling cycle = 4096 clocks \hideinitializer */ #define GPIO_DBCTL_DBCLKSEL_8192 0x0000000DUL /*!< GPIO_DBCTL setting for sampling cycle = 8192 clocks \hideinitializer */ #define GPIO_DBCTL_DBCLKSEL_16384 0x0000000EUL /*!< GPIO_DBCTL setting for sampling cycle = 16384 clocks \hideinitializer */ #define GPIO_DBCTL_DBCLKSEL_32768 0x0000000FUL /*!< GPIO_DBCTL setting for sampling cycle = 32768 clocks \hideinitializer */ /* Define GPIO Pin Data Input/Output. It could be used to control each I/O pin by pin address mapping. Example 1: PA0 = 1; It is used to set GPIO PA.0 to high; Example 2: if (PA0) PA0 = 0; If GPIO PA.0 pin status is high, then set GPIO PA.0 data output to low. */ #define GPIO_PIN_DATA(port, pin) (*((volatile uint32_t *)((GPIO_PIN_DATA_BASE+(0x40*(port))) + ((pin)<<2)))) /*!< Pin Data Input/Output \hideinitializer */ #define PA0 GPIO_PIN_DATA(0, 0 ) /*!< Specify PA.0 Pin Data Input/Output \hideinitializer */ #define PA1 GPIO_PIN_DATA(0, 1 ) /*!< Specify PA.1 Pin Data Input/Output \hideinitializer */ #define PA2 GPIO_PIN_DATA(0, 2 ) /*!< Specify PA.2 Pin Data Input/Output \hideinitializer */ #define PA3 GPIO_PIN_DATA(0, 3 ) /*!< Specify PA.3 Pin Data Input/Output \hideinitializer */ #define PA4 GPIO_PIN_DATA(0, 4 ) /*!< Specify PA.4 Pin Data Input/Output \hideinitializer */ #define PA5 GPIO_PIN_DATA(0, 5 ) /*!< Specify PA.5 Pin Data Input/Output \hideinitializer */ #define PA6 GPIO_PIN_DATA(0, 6 ) /*!< Specify PA.6 Pin Data Input/Output \hideinitializer */ #define PA7 GPIO_PIN_DATA(0, 7 ) /*!< Specify PA.7 Pin Data Input/Output \hideinitializer */ #define PA8 GPIO_PIN_DATA(0, 8 ) /*!< Specify PA.8 Pin Data Input/Output \hideinitializer */ #define PA9 GPIO_PIN_DATA(0, 9 ) /*!< Specify PA.9 Pin Data Input/Output \hideinitializer */ #define PA10 GPIO_PIN_DATA(0, 10) /*!< Specify PA.10 Pin Data Input/Output \hideinitializer */ #define PA11 GPIO_PIN_DATA(0, 11) /*!< Specify PA.11 Pin Data Input/Output \hideinitializer */ #define PA12 GPIO_PIN_DATA(0, 12) /*!< Specify PA.12 Pin Data Input/Output \hideinitializer */ #define PA13 GPIO_PIN_DATA(0, 13) /*!< Specify PA.13 Pin Data Input/Output \hideinitializer */ #define PA14 GPIO_PIN_DATA(0, 14) /*!< Specify PA.14 Pin Data Input/Output \hideinitializer */ #define PA15 GPIO_PIN_DATA(0, 15) /*!< Specify PA.15 Pin Data Input/Output \hideinitializer */ #define PB0 GPIO_PIN_DATA(1, 0 ) /*!< Specify PB.0 Pin Data Input/Output \hideinitializer */ #define PB1 GPIO_PIN_DATA(1, 1 ) /*!< Specify PB.1 Pin Data Input/Output \hideinitializer */ #define PB2 GPIO_PIN_DATA(1, 2 ) /*!< Specify PB.2 Pin Data Input/Output \hideinitializer */ #define PB3 GPIO_PIN_DATA(1, 3 ) /*!< Specify PB.3 Pin Data Input/Output \hideinitializer */ #define PB4 GPIO_PIN_DATA(1, 4 ) /*!< Specify PB.4 Pin Data Input/Output \hideinitializer */ #define PB5 GPIO_PIN_DATA(1, 5 ) /*!< Specify PB.5 Pin Data Input/Output \hideinitializer */ #define PB6 GPIO_PIN_DATA(1, 6 ) /*!< Specify PB.6 Pin Data Input/Output \hideinitializer */ #define PB7 GPIO_PIN_DATA(1, 7 ) /*!< Specify PB.7 Pin Data Input/Output \hideinitializer */ #define PB8 GPIO_PIN_DATA(1, 8 ) /*!< Specify PB.8 Pin Data Input/Output \hideinitializer */ #define PB9 GPIO_PIN_DATA(1, 9 ) /*!< Specify PB.9 Pin Data Input/Output \hideinitializer */ #define PB10 GPIO_PIN_DATA(1, 10) /*!< Specify PB.10 Pin Data Input/Output \hideinitializer */ #define PB11 GPIO_PIN_DATA(1, 11) /*!< Specify PB.11 Pin Data Input/Output \hideinitializer */ #define PB12 GPIO_PIN_DATA(1, 12) /*!< Specify PB.12 Pin Data Input/Output \hideinitializer */ #define PB13 GPIO_PIN_DATA(1, 13) /*!< Specify PB.13 Pin Data Input/Output \hideinitializer */ #define PB14 GPIO_PIN_DATA(1, 14) /*!< Specify PB.14 Pin Data Input/Output \hideinitializer */ #define PB15 GPIO_PIN_DATA(1, 15) /*!< Specify PB.15 Pin Data Input/Output \hideinitializer */ #define PC0 GPIO_PIN_DATA(2, 0 ) /*!< Specify PC.0 Pin Data Input/Output \hideinitializer */ #define PC1 GPIO_PIN_DATA(2, 1 ) /*!< Specify PC.1 Pin Data Input/Output \hideinitializer */ #define PC2 GPIO_PIN_DATA(2, 2 ) /*!< Specify PC.2 Pin Data Input/Output \hideinitializer */ #define PC3 GPIO_PIN_DATA(2, 3 ) /*!< Specify PC.3 Pin Data Input/Output \hideinitializer */ #define PC4 GPIO_PIN_DATA(2, 4 ) /*!< Specify PC.4 Pin Data Input/Output \hideinitializer */ #define PC5 GPIO_PIN_DATA(2, 5 ) /*!< Specify PC.5 Pin Data Input/Output \hideinitializer */ #define PC6 GPIO_PIN_DATA(2, 6 ) /*!< Specify PC.6 Pin Data Input/Output \hideinitializer */ #define PC7 GPIO_PIN_DATA(2, 7 ) /*!< Specify PC.7 Pin Data Input/Output \hideinitializer */ #define PC8 GPIO_PIN_DATA(2, 8 ) /*!< Specify PC.8 Pin Data Input/Output \hideinitializer */ #define PC9 GPIO_PIN_DATA(2, 9 ) /*!< Specify PC.9 Pin Data Input/Output \hideinitializer */ #define PC10 GPIO_PIN_DATA(2, 10) /*!< Specify PC.10 Pin Data Input/Output \hideinitializer */ #define PC11 GPIO_PIN_DATA(2, 11) /*!< Specify PC.11 Pin Data Input/Output \hideinitializer */ #define PC12 GPIO_PIN_DATA(2, 12) /*!< Specify PC.12 Pin Data Input/Output \hideinitializer */ #define PC13 GPIO_PIN_DATA(2, 13) /*!< Specify PC.13 Pin Data Input/Output \hideinitializer */ #define PC14 GPIO_PIN_DATA(2, 14) /*!< Specify PC.14 Pin Data Input/Output \hideinitializer */ #define PD0 GPIO_PIN_DATA(3, 0 ) /*!< Specify PD.0 Pin Data Input/Output \hideinitializer */ #define PD1 GPIO_PIN_DATA(3, 1 ) /*!< Specify PD.1 Pin Data Input/Output \hideinitializer */ #define PD2 GPIO_PIN_DATA(3, 2 ) /*!< Specify PD.2 Pin Data Input/Output \hideinitializer */ #define PD3 GPIO_PIN_DATA(3, 3 ) /*!< Specify PD.3 Pin Data Input/Output \hideinitializer */ #define PD4 GPIO_PIN_DATA(3, 4 ) /*!< Specify PD.4 Pin Data Input/Output \hideinitializer */ #define PD5 GPIO_PIN_DATA(3, 5 ) /*!< Specify PD.5 Pin Data Input/Output \hideinitializer */ #define PD6 GPIO_PIN_DATA(3, 6 ) /*!< Specify PD.6 Pin Data Input/Output \hideinitializer */ #define PD7 GPIO_PIN_DATA(3, 7 ) /*!< Specify PD.7 Pin Data Input/Output \hideinitializer */ #define PD8 GPIO_PIN_DATA(3, 8 ) /*!< Specify PD.8 Pin Data Input/Output \hideinitializer */ #define PD9 GPIO_PIN_DATA(3, 9 ) /*!< Specify PD.9 Pin Data Input/Output \hideinitializer */ #define PD10 GPIO_PIN_DATA(3, 10) /*!< Specify PD.10 Pin Data Input/Output \hideinitializer */ #define PD11 GPIO_PIN_DATA(3, 11) /*!< Specify PD.11 Pin Data Input/Output \hideinitializer */ #define PD12 GPIO_PIN_DATA(3, 12) /*!< Specify PD.12 Pin Data Input/Output \hideinitializer */ #define PD13 GPIO_PIN_DATA(3, 13) /*!< Specify PD.13 Pin Data Input/Output \hideinitializer */ #define PD14 GPIO_PIN_DATA(3, 14) /*!< Specify PD.14 Pin Data Input/Output \hideinitializer */ #define PE0 GPIO_PIN_DATA(4, 0 ) /*!< Specify PE.0 Pin Data Input/Output \hideinitializer */ #define PE1 GPIO_PIN_DATA(4, 1 ) /*!< Specify PE.1 Pin Data Input/Output \hideinitializer */ #define PE2 GPIO_PIN_DATA(4, 2 ) /*!< Specify PE.2 Pin Data Input/Output \hideinitializer */ #define PE3 GPIO_PIN_DATA(4, 3 ) /*!< Specify PE.3 Pin Data Input/Output \hideinitializer */ #define PE4 GPIO_PIN_DATA(4, 4 ) /*!< Specify PE.4 Pin Data Input/Output \hideinitializer */ #define PE5 GPIO_PIN_DATA(4, 5 ) /*!< Specify PE.5 Pin Data Input/Output \hideinitializer */ #define PE6 GPIO_PIN_DATA(4, 6 ) /*!< Specify PE.6 Pin Data Input/Output \hideinitializer */ #define PE7 GPIO_PIN_DATA(4, 7 ) /*!< Specify PE.7 Pin Data Input/Output \hideinitializer */ #define PE8 GPIO_PIN_DATA(4, 8 ) /*!< Specify PE.8 Pin Data Input/Output \hideinitializer */ #define PE9 GPIO_PIN_DATA(4, 9 ) /*!< Specify PE.9 Pin Data Input/Output \hideinitializer */ #define PE10 GPIO_PIN_DATA(4, 10) /*!< Specify PE.10 Pin Data Input/Output \hideinitializer */ #define PE11 GPIO_PIN_DATA(4, 11) /*!< Specify PE.11 Pin Data Input/Output \hideinitializer */ #define PE12 GPIO_PIN_DATA(4, 12) /*!< Specify PE.12 Pin Data Input/Output \hideinitializer */ #define PE13 GPIO_PIN_DATA(4, 13) /*!< Specify PE.13 Pin Data Input/Output \hideinitializer */ #define PE14 GPIO_PIN_DATA(4, 14) /*!< Specify PE.14 Pin Data Input/Output \hideinitializer */ #define PE15 GPIO_PIN_DATA(4, 15) /*!< Specify PE.15 Pin Data Input/Output \hideinitializer */ #define PF0 GPIO_PIN_DATA(5, 0 ) /*!< Specify PF.0 Pin Data Input/Output \hideinitializer */ #define PF1 GPIO_PIN_DATA(5, 1 ) /*!< Specify PF.1 Pin Data Input/Output \hideinitializer */ #define PF2 GPIO_PIN_DATA(5, 2 ) /*!< Specify PF.2 Pin Data Input/Output \hideinitializer */ #define PF3 GPIO_PIN_DATA(5, 3 ) /*!< Specify PF.3 Pin Data Input/Output \hideinitializer */ #define PF4 GPIO_PIN_DATA(5, 4 ) /*!< Specify PF.4 Pin Data Input/Output \hideinitializer */ #define PF5 GPIO_PIN_DATA(5, 5 ) /*!< Specify PF.5 Pin Data Input/Output \hideinitializer */ #define PF6 GPIO_PIN_DATA(5, 6 ) /*!< Specify PF.6 Pin Data Input/Output \hideinitializer */ #define PF7 GPIO_PIN_DATA(5, 7 ) /*!< Specify PF.7 Pin Data Input/Output \hideinitializer */ #define PF8 GPIO_PIN_DATA(5, 8 ) /*!< Specify PF.8 Pin Data Input/Output \hideinitializer */ #define PF9 GPIO_PIN_DATA(5, 9 ) /*!< Specify PF.9 Pin Data Input/Output \hideinitializer */ #define PF10 GPIO_PIN_DATA(5, 10) /*!< Specify PF.10 Pin Data Input/Output \hideinitializer */ #define PF11 GPIO_PIN_DATA(5, 11) /*!< Specify PF.11 Pin Data Input/Output \hideinitializer */ #define PG0 GPIO_PIN_DATA(6, 0 ) /*!< Specify PG.0 Pin Data Input/Output \hideinitializer */ #define PG1 GPIO_PIN_DATA(6, 1 ) /*!< Specify PG.1 Pin Data Input/Output \hideinitializer */ #define PG2 GPIO_PIN_DATA(6, 2 ) /*!< Specify PG.2 Pin Data Input/Output \hideinitializer */ #define PG3 GPIO_PIN_DATA(6, 3 ) /*!< Specify PG.3 Pin Data Input/Output \hideinitializer */ #define PG4 GPIO_PIN_DATA(6, 4 ) /*!< Specify PG.4 Pin Data Input/Output \hideinitializer */ #define PG5 GPIO_PIN_DATA(6, 5 ) /*!< Specify PG.5 Pin Data Input/Output \hideinitializer */ #define PG6 GPIO_PIN_DATA(6, 6 ) /*!< Specify PG.6 Pin Data Input/Output \hideinitializer */ #define PG7 GPIO_PIN_DATA(6, 7 ) /*!< Specify PG.7 Pin Data Input/Output \hideinitializer */ #define PG8 GPIO_PIN_DATA(6, 8 ) /*!< Specify PG.8 Pin Data Input/Output \hideinitializer */ #define PG9 GPIO_PIN_DATA(6, 9 ) /*!< Specify PG.9 Pin Data Input/Output \hideinitializer */ #define PG10 GPIO_PIN_DATA(6, 10) /*!< Specify PG.10 Pin Data Input/Output \hideinitializer */ #define PG11 GPIO_PIN_DATA(6, 11) /*!< Specify PG.11 Pin Data Input/Output \hideinitializer */ #define PG12 GPIO_PIN_DATA(6, 12) /*!< Specify PG.12 Pin Data Input/Output \hideinitializer */ #define PG13 GPIO_PIN_DATA(6, 13) /*!< Specify PG.13 Pin Data Input/Output \hideinitializer */ #define PG14 GPIO_PIN_DATA(6, 14) /*!< Specify PG.14 Pin Data Input/Output \hideinitializer */ #define PG15 GPIO_PIN_DATA(6, 15) /*!< Specify PG.15 Pin Data Input/Output \hideinitializer */ #define PH0 GPIO_PIN_DATA(7, 0 ) /*!< Specify PH.0 Pin Data Input/Output \hideinitializer */ #define PH1 GPIO_PIN_DATA(7, 1 ) /*!< Specify PH.1 Pin Data Input/Output \hideinitializer */ #define PH2 GPIO_PIN_DATA(7, 2 ) /*!< Specify PH.2 Pin Data Input/Output \hideinitializer */ #define PH3 GPIO_PIN_DATA(7, 3 ) /*!< Specify PH.3 Pin Data Input/Output \hideinitializer */ #define PH4 GPIO_PIN_DATA(7, 4 ) /*!< Specify PH.4 Pin Data Input/Output \hideinitializer */ #define PH5 GPIO_PIN_DATA(7, 5 ) /*!< Specify PH.5 Pin Data Input/Output \hideinitializer */ #define PH6 GPIO_PIN_DATA(7, 6 ) /*!< Specify PH.6 Pin Data Input/Output \hideinitializer */ #define PH7 GPIO_PIN_DATA(7, 7 ) /*!< Specify PH.7 Pin Data Input/Output \hideinitializer */ #define PH8 GPIO_PIN_DATA(7, 8 ) /*!< Specify PH.8 Pin Data Input/Output \hideinitializer */ #define PH9 GPIO_PIN_DATA(7, 9 ) /*!< Specify PH.9 Pin Data Input/Output \hideinitializer */ #define PH10 GPIO_PIN_DATA(7, 10) /*!< Specify PH.10 Pin Data Input/Output \hideinitializer */ #define PH11 GPIO_PIN_DATA(7, 11) /*!< Specify PH.11 Pin Data Input/Output \hideinitializer */ /*@}*/ /* end of group GPIO_EXPORTED_CONSTANTS */ /** @addtogroup GPIO_EXPORTED_FUNCTIONS GPIO Exported Functions @{ */ /** * @brief Clear GPIO Pin Interrupt Flag * * @param[in] port GPIO port. It could be It could be PA, PB, PC, PD, PE, PF, PG or PH. * @param[in] u32PinMask The single or multiple pins of specified GPIO port. * It could be BIT0 ~ BIT15 for PA, PB, PC, PD, PF and PH GPIO port. * It could be BIT0 ~ BIT13 for PE GPIO port. * It could be BIT0 ~ BIT11 for PG GPIO port. * * @return None * * @details Clear the interrupt status of specified GPIO pin. * \hideinitializer */ #define GPIO_CLR_INT_FLAG(port, u32PinMask) ((port)->INTSRC = (u32PinMask)) /** * @brief Disable Pin De-bounce Function * * @param[in] port GPIO port. It could be It could be PA, PB, PC, PD, PE, PF, PG or PH. * @param[in] u32PinMask The single or multiple pins of specified GPIO port. * It could be BIT0 ~ BIT15 for PA, PB, PC, PD, PF and PH GPIO port. * It could be BIT0 ~ BIT13 for PE GPIO port. * It could be BIT0 ~ BIT11 for PG GPIO port. * * @return None * * @details Disable the interrupt de-bounce function of specified GPIO pin. * \hideinitializer */ #define GPIO_DISABLE_DEBOUNCE(port, u32PinMask) ((port)->DBEN &= ~(u32PinMask)) /** * @brief Enable Pin De-bounce Function * * @param[in] port GPIO port. It could be It could be PA, PB, PC, PD, PE, PF, PG or PH. * @param[in] u32PinMask The single or multiple pins of specified GPIO port. * It could be BIT0 ~ BIT15 for PA, PB, PC, PD, PF and PH GPIO port. * It could be BIT0 ~ BIT13 for PE GPIO port. * It could be BIT0 ~ BIT11 for PG GPIO port. * @return None * * @details Enable the interrupt de-bounce function of specified GPIO pin. * \hideinitializer */ #define GPIO_ENABLE_DEBOUNCE(port, u32PinMask) ((port)->DBEN |= (u32PinMask)) /** * @brief Disable I/O Digital Input Path * * @param[in] port GPIO port. It could be It could be PA, PB, PC, PD, PE, PF, PG or PH. * @param[in] u32PinMask The single or multiple pins of specified GPIO port. * It could be BIT0 ~ BIT15 for PA, PB, PC, PD, PF and PH GPIO port. * It could be BIT0 ~ BIT13 for PE GPIO port. * It could be BIT0 ~ BIT11 for PG GPIO port. * * @return None * * @details Disable I/O digital input path of specified GPIO pin. * \hideinitializer */ #define GPIO_DISABLE_DIGITAL_PATH(port, u32PinMask) ((port)->DINOFF |= ((u32PinMask)<<16)) /** * @brief Enable I/O Digital Input Path * * @param[in] port GPIO port. It could be It could be PA, PB, PC, PD, PE, PF, PG or PH. * @param[in] u32PinMask The single or multiple pins of specified GPIO port. * It could be BIT0 ~ BIT15 for PA, PB, PC, PD, PF and PH GPIO port. * It could be BIT0 ~ BIT13 for PE GPIO port. * It could be BIT0 ~ BIT11 for PG GPIO port. * * @return None * * @details Enable I/O digital input path of specified GPIO pin. * \hideinitializer */ #define GPIO_ENABLE_DIGITAL_PATH(port, u32PinMask) ((port)->DINOFF &= ~((u32PinMask)<<16)) /** * @brief Disable I/O DOUT mask * * @param[in] port GPIO port. It could be It could be PA, PB, PC, PD, PE, PF, PG or PH. * @param[in] u32PinMask The single or multiple pins of specified GPIO port. * It could be BIT0 ~ BIT15 for PA, PB, PC, PD, PF and PH GPIO port. * It could be BIT0 ~ BIT13 for PE GPIO port. * It could be BIT0 ~ BIT11 for PG GPIO port. * * @return None * * @details Disable I/O DOUT mask of specified GPIO pin. * \hideinitializer */ #define GPIO_DISABLE_DOUT_MASK(port, u32PinMask) ((port)->DATMSK &= ~(u32PinMask)) /** * @brief Enable I/O DOUT mask * * @param[in] port GPIO port. It could be It could be PA, PB, PC, PD, PE, PF, PG or PH. * @param[in] u32PinMask The single or multiple pins of specified GPIO port. * It could be BIT0 ~ BIT15 for PA, PB, PC, PD, PF and PH GPIO port. * It could be BIT0 ~ BIT13 for PE GPIO port. * It could be BIT0 ~ BIT11 for PG GPIO port. * * @return None * * @details Enable I/O DOUT mask of specified GPIO pin. * \hideinitializer */ #define GPIO_ENABLE_DOUT_MASK(port, u32PinMask) ((port)->DATMSK |= (u32PinMask)) /** * @brief Get GPIO Pin Interrupt Flag * * @param[in] port GPIO port. It could be It could be PA, PB, PC, PD, PE, PF, PG or PH. * @param[in] u32PinMask The single or multiple pins of specified GPIO port. * It could be BIT0 ~ BIT15 for PA, PB, PC, PD, PF and PH GPIO port. * It could be BIT0 ~ BIT13 for PE GPIO port. * It could be BIT0 ~ BIT11 for PG GPIO port. * * @retval 0 No interrupt at specified GPIO pin * @retval 1 The specified GPIO pin generate an interrupt * * @details Get the interrupt status of specified GPIO pin. * \hideinitializer */ #define GPIO_GET_INT_FLAG(port, u32PinMask) ((port)->INTSRC & (u32PinMask)) /** * @brief Set De-bounce Sampling Cycle Time * * @param[in] u32ClkSrc The de-bounce counter clock source. It could be GPIO_DBCTL_DBCLKSRC_HCLK or GPIO_DBCTL_DBCLKSRC_LIRC. * @param[in] u32ClkSel The de-bounce sampling cycle selection. It could be * - \ref GPIO_DBCTL_DBCLKSEL_1 * - \ref GPIO_DBCTL_DBCLKSEL_2 * - \ref GPIO_DBCTL_DBCLKSEL_4 * - \ref GPIO_DBCTL_DBCLKSEL_8 * - \ref GPIO_DBCTL_DBCLKSEL_16 * - \ref GPIO_DBCTL_DBCLKSEL_32 * - \ref GPIO_DBCTL_DBCLKSEL_64 * - \ref GPIO_DBCTL_DBCLKSEL_128 * - \ref GPIO_DBCTL_DBCLKSEL_256 * - \ref GPIO_DBCTL_DBCLKSEL_512 * - \ref GPIO_DBCTL_DBCLKSEL_1024 * - \ref GPIO_DBCTL_DBCLKSEL_2048 * - \ref GPIO_DBCTL_DBCLKSEL_4096 * - \ref GPIO_DBCTL_DBCLKSEL_8192 * - \ref GPIO_DBCTL_DBCLKSEL_16384 * - \ref GPIO_DBCTL_DBCLKSEL_32768 * * @return None * * @details Set the interrupt de-bounce sampling cycle time based on the debounce counter clock source. \n * Example: _GPIO_SET_DEBOUNCE_TIME(GPIO_DBCTL_DBCLKSRC_LIRC, GPIO_DBCTL_DBCLKSEL_4). \n * It's meaning the De-debounce counter clock source is internal 10 KHz and sampling cycle selection is 4. \n * Then the target de-bounce sampling cycle time is (4)*(1/(10*1000)) s = 4*0.0001 s = 400 us, * and system will sampling interrupt input once per 00 us. * \hideinitializer */ #define GPIO_SET_DEBOUNCE_TIME(u32ClkSrc, u32ClkSel) (GPIO->DBCTL = (GPIO_DBCTL_ICLKON_Msk | (u32ClkSrc) | (u32ClkSel))) /** * @brief Get GPIO Port IN Data * * @param[in] port GPIO port. It could be It could be PA, PB, PC, PD, PE, PF, PG or PH. * * @return The specified port data * * @details Get the PIN register of specified GPIO port. * \hideinitializer */ #define GPIO_GET_IN_DATA(port) ((port)->PIN) /** * @brief Set GPIO Port OUT Data * * @param[in] port GPIO port. It could be It could be PA, PB, PC, PD, PE, PF, PG or PH. * @param[in] u32Data GPIO port data. * * @return None * * @details Set the Data into specified GPIO port. * \hideinitializer */ #define GPIO_SET_OUT_DATA(port, u32Data) ((port)->DOUT = (u32Data)) /** * @brief Toggle Specified GPIO pin * * @param[in] u32Pin Pxy * * @return None * * @details Toggle the specified GPIO pint. * \hideinitializer */ #define GPIO_TOGGLE(u32Pin) ((u32Pin) ^= 1) /** * @brief Enable External GPIO interrupt * * @param[in] port GPIO port. It could be It could be PA, PB, PC, PD, PE, PF, PG or PH. * @param[in] u32Pin The pin of specified GPIO port. * It could be 0 ~ 15 for PA, PB, PC, PD, PF and PH GPIO port. * It could be 0 ~ 13 for PE GPIO port. * It could be 0 ~ 11 for PG GPIO port. * @param[in] u32IntAttribs The interrupt attribute of specified GPIO pin. It could be \n * GPIO_INT_RISING, GPIO_INT_FALLING, GPIO_INT_BOTH_EDGE, GPIO_INT_HIGH, GPIO_INT_LOW. * * @return None * * @details This function is used to enable specified GPIO pin interrupt. * \hideinitializer */ #define GPIO_EnableEINT GPIO_EnableInt /** * @brief Disable External GPIO interrupt * * @param[in] port GPIO port. It could be It could be PA, PB, PC, PD, PE, PF, PG or PH. * @param[in] u32Pin The pin of specified GPIO port. * It could be 0 ~ 15 for PA, PB, PC, PD, PF and PH GPIO port. * It could be 0 ~ 13 for PE GPIO port. * It could be 0 ~ 11 for PG GPIO port. * * @return None * * @details This function is used to enable specified GPIO pin interrupt. * \hideinitializer */ #define GPIO_DisableEINT GPIO_DisableInt void GPIO_SetMode(GPIO_T *port, uint32_t u32PinMask, uint32_t u32Mode); void GPIO_EnableInt(GPIO_T *port, uint32_t u32Pin, uint32_t u32IntAttribs); void GPIO_DisableInt(GPIO_T *port, uint32_t u32Pin); void GPIO_SetSlewCtl(GPIO_T *port, uint32_t u32PinMask, uint32_t u32Mode); void GPIO_SetPullCtl(GPIO_T *port, uint32_t u32PinMask, uint32_t u32Mode); /*@}*/ /* end of group GPIO_EXPORTED_FUNCTIONS */ /*@}*/ /* end of group GPIO_Driver */ /*@}*/ /* end of group Standard_Driver */ #ifdef __cplusplus } #endif #endif /* __GPIO_H__ */ /*** (C) COPYRIGHT 2013~2016 Nuvoton Technology Corp. ***/