menu "Hardware Drivers Config" config SOC_STM32F407ZG bool select SOC_SERIES_STM32F4 select RT_USING_COMPONENTS_INIT select RT_USING_USER_MAIN default y menu "Onboard Peripheral Drivers" config BSP_USING_USB_TO_USART bool "Enable USB TO USART (uart1)" select BSP_USING_UART select BSP_USING_UART1 default y config BSP_USING_COM2 bool "Enable COM2 (uart2 pin conflict with Ethernet and PWM)" depends on (!BSP_USING_ETH && !BSP_USING_PWM) select BSP_USING_UART select BSP_USING_UART2 default n config BSP_USING_COM3 bool "Enable COM3 (uart3)" select BSP_USING_UART select BSP_USING_UART3 default n config BSP_USING_SRAM bool "Enable SRAM" select BSP_USING_EXT_FMC_IO select BSP_USING_FMC default n config BSP_USING_MCU_LCD bool "Enable ATK LCD" select BSP_USING_SRAM default n if BSP_USING_MCU_LCD config BSP_USING_MCU_LCD_TEST bool "Enable lcd fill test" default y endif config BSP_USING_TOUCH bool "Use LCD TOUCH" select BSP_USING_I2C2 default n if BSP_USING_TOUCH config BSP_TOUCH_INT_PIN int "Touch interrupt pin, PB1" default 17 endif config BSP_USING_LVGL bool "Enable LVGL for LCD" select BSP_USING_MCU_LCD select BSP_USING_TOUCH select PKG_USING_LVGL default n config BSP_USING_SPI_FLASH bool "Enable SPI FLASH (W25Q128 spi1)" select BSP_USING_SPI select BSP_USING_SPI1 select RT_USING_SFUD select RT_SFUD_USING_SFDP default n config BSP_USING_EEPROM bool "Enable I2C EEPROM (i2c1)" select BSP_USING_I2C1 default n config BSP_USING_ETH bool "Enable Ethernet" default n select RT_USING_LWIP select RT_LWIP_USING_HW_CHECKSUM config BSP_USING_ETH_SAL bool "Enable Ethernet with SAL" depends on BSP_USING_ETH default y select RT_USING_SAL select SAL_USING_POSIX config PHY_USING_LAN8720A bool depends on BSP_USING_ETH default y config BSP_USING_MPU6050 bool "Enable MPU6050 (i2c1)" default n select BSP_USING_I2C1 select PKG_USING_MPU6XXX menu "Enable File System" config BSP_USING_FS bool default n config BSP_USING_SDCARD_FATFS bool "Enable SDCARD (FATFS)" select BSP_USING_SDIO select RT_USING_DFS select RT_USING_DFS_ELMFAT select RT_USING_DFS_ROMFS select BSP_USING_FS default n config SDIO_MAX_FREQ int "sdio max freq" range 0 24000000 depends on BSP_USING_SDCARD default 1000000 config BSP_USING_SPI_FLASH_LITTLEFS bool "Enable SPI-FLASH (LittleFS)" select RT_USING_DFS select RT_USING_DFS_ROMFS select RT_USING_MTD_NOR select BSP_USING_SPI_FLASH select BSP_USING_FS select PKG_USING_FAL select FAL_USING_AUTO_INIT select FAL_PART_HAS_TABLE_CFG select PKG_USING_LITTLEFS default n endmenu endmenu menu "On-chip Peripheral Drivers" config BSP_USING_GPIO bool "Enable GPIO" select RT_USING_PIN default y menuconfig BSP_USING_UART bool "Enable UART" default y select RT_USING_SERIAL if BSP_USING_UART config BSP_USING_UART1 bool "Enable UART1" default y config BSP_UART1_RX_USING_DMA bool "Enable UART1 RX DMA" depends on BSP_USING_UART1 && RT_SERIAL_USING_DMA default n config BSP_UART1_TX_USING_DMA bool "Enable UART1 TX DMA" depends on BSP_USING_UART1 && RT_SERIAL_USING_DMA default n config BSP_USING_UART2 bool "Enable UART2" default n config BSP_UART2_RX_USING_DMA bool "Enable UART2 RX DMA" depends on BSP_USING_UART2 && RT_SERIAL_USING_DMA default n config BSP_UART2_TX_USING_DMA bool "Enable UART2 TX DMA" depends on BSP_USING_UART2 && RT_SERIAL_USING_DMA default n config BSP_USING_UART3 bool "Enable UART3" default n config BSP_UART3_RX_USING_DMA bool "Enable UART3 RX DMA" depends on BSP_USING_UART3 && RT_SERIAL_USING_DMA default n config BSP_UART3_TX_USING_DMA bool "Enable UART3 TX DMA" depends on BSP_USING_UART3 && RT_SERIAL_USING_DMA default n config BSP_USING_UART4 bool "Enable UART4" default n config BSP_UART4_RX_USING_DMA bool "Enable UART4 RX DMA" depends on BSP_USING_UART4 && RT_SERIAL_USING_DMA default n config BSP_UART4_TX_USING_DMA bool "Enable UART4 TX DMA" depends on BSP_USING_UART4 && RT_SERIAL_USING_DMA default n config BSP_USING_UART5 bool "Enable UART5" default n config BSP_UART5_RX_USING_DMA bool "Enable UART5 RX DMA" depends on BSP_USING_UART5 && RT_SERIAL_USING_DMA default n config BSP_UART5_TX_USING_DMA bool "Enable UART5 TX DMA" depends on BSP_USING_UART5 && RT_SERIAL_USING_DMA default n config BSP_USING_UART6 bool "Enable UART6" default n config BSP_UART6_RX_USING_DMA bool "Enable UART6 RX DMA" depends on BSP_USING_UART6 && RT_SERIAL_USING_DMA default n config BSP_UART6_TX_USING_DMA bool "Enable UART6 TX DMA" depends on BSP_USING_UART6 && RT_SERIAL_USING_DMA default n endif menuconfig BSP_USING_TIM bool "Enable timer" default n select RT_USING_HWTIMER if BSP_USING_TIM config BSP_USING_TIM11 bool "Enable TIM11" default n config BSP_USING_TIM13 bool "Enable TIM13" default n config BSP_USING_TIM14 bool "Enable TIM14" default n endif menuconfig BSP_USING_PWM bool "Enable pwm" default n select RT_USING_PWM if BSP_USING_PWM menuconfig BSP_USING_PWM2 bool "Enable timer2 output pwm" default n if BSP_USING_PWM2 config BSP_USING_PWM2_CH4 bool "Enable PWM2 channel4" default n endif endif config BSP_USING_ON_CHIP_FLASH bool "Enable on-chip FLASH" default n menuconfig BSP_USING_SPI bool "Enable SPI BUS" default n select RT_USING_SPI if BSP_USING_SPI config BSP_USING_SPI1 bool "Enable SPI1 BUS" default n config BSP_SPI1_TX_USING_DMA bool "Enable SPI1 TX DMA" depends on BSP_USING_SPI1 default n config BSP_SPI1_RX_USING_DMA bool "Enable SPI1 RX DMA" depends on BSP_USING_SPI1 select BSP_SPI1_TX_USING_DMA default n config BSP_USING_SPI2 bool "Enable SPI2 BUS" default n config BSP_SPI2_TX_USING_DMA bool "Enable SPI2 TX DMA" depends on BSP_USING_SPI2 default n config BSP_SPI2_RX_USING_DMA bool "Enable SPI2 RX DMA" depends on BSP_USING_SPI2 select BSP_SPI2_TX_USING_DMA default n endif menuconfig BSP_USING_ADC bool "Enable ADC" default n select RT_USING_ADC if BSP_USING_ADC config BSP_USING_ADC1 bool "Enable ADC1" default n endif menuconfig BSP_USING_I2C1 bool "Enable I2C1 BUS (software simulation)" default y select RT_USING_I2C select RT_USING_I2C_BITOPS select RT_USING_PIN if BSP_USING_I2C1 config BSP_I2C1_SCL_PIN int "i2c1 scl pin number" range 0 143 default 24 config BSP_I2C1_SDA_PIN int "I2C1 sda pin number" range 0 143 default 25 endif menuconfig BSP_USING_I2C2 bool "Enable LCD Touch BUS (software simulation)" default y select RT_USING_I2C select RT_USING_I2C_BITOPS select RT_USING_PIN if BSP_USING_I2C2 config BSP_I2C2_SCL_PIN int "i2c2 scl pin number, PB0" range 0 143 default 16 config BSP_I2C2_SDA_PIN int "I2C2 sda pin number, PF11" range 0 143 default 91 endif menuconfig BSP_USING_DAC bool "Enable DAC" default n select RT_USING_DAC if BSP_USING_DAC config BSP_USING_DAC1 bool "Enable DAC1" default n endif menuconfig BSP_USING_ONCHIP_RTC bool "Enable RTC" select RT_USING_RTC default n if BSP_USING_ONCHIP_RTC choice prompt "Select clock source" default BSP_RTC_USING_LSE config BSP_RTC_USING_LSE bool "RTC USING LSE" config BSP_RTC_USING_LSI bool "RTC USING LSI" endchoice endif config BSP_USING_WDT bool "Enable Watchdog Timer" select RT_USING_WDT default n config BSP_USING_SDIO bool "Enable SDIO" select RT_USING_SDIO select RT_USING_DFS default n config BSP_USING_USBD bool "Enable USB Device" select RT_USING_USB_DEVICE default n menuconfig BSP_USING_USBH bool "Enable USB Host" select RT_USING_USB_HOST default n if BSP_USING_USBH menuconfig RT_USBH_MSTORAGE bool "Enable Udisk Drivers" default n if RT_USBH_MSTORAGE config UDISK_MOUNTPOINT string "Udisk mount dir" default "/" endif endif menuconfig BSP_USING_PULSE_ENCODER bool "Enable Pulse Encoder" default n select RT_USING_PULSE_ENCODER if BSP_USING_PULSE_ENCODER config BSP_USING_PULSE_ENCODER4 bool "Enable Pulse Encoder4" default n endif config BSP_USING_EXT_FMC_IO bool default n config BSP_USING_FMC bool default n source "../libraries/HAL_Drivers/Kconfig" endmenu menu "Board extended module Drivers" menuconfig BSP_USING_AT_ESP8266 bool "Enable ESP8266(AT Command, COM3)" default n select BSP_USING_COM3 select PKG_USING_AT_DEVICE select AT_DEVICE_USING_ESP8266 select AT_DEVICE_ESP8266_SAMPLE if BSP_USING_AT_ESP8266 config ESP8266_SAMPLE_WIFI_SSID string "WIFI ssid" default "rtthread" config ESP8266_SAMPLE_WIFI_PASSWORD string "WIFI password" default "12345678" config ESP8266_SAMPLE_CLIENT_NAME string "AT client device name (Must be 'uart3')" default "uart3" config ESP8266_SAMPLE_RECV_BUFF_LEN int "The maximum length of receive line buffer" default 512 endif endmenu endmenu