/* * Copyright 2017-2021 NXP * All rights reserved. * * SPDX-License-Identifier: BSD-3-Clause */ #ifndef _FSL_ROMAPI_H_ #define _FSL_ROMAPI_H_ #include "fsl_common.h" /*! * @addtogroup romapi * @{ */ /*! @brief ROM API version 1.1.1. */ #define FSL_ROM_ROMAPI_VERSION (MAKE_VERSION(1U, 1U, 1U)) /*! @brief ROM FLEXSPI NOR driver version 1.7.0. */ #define FSL_ROM_FLEXSPINOR_DRIVER_VERSION (MAKE_VERSION(1U, 7U, 0U)) /*! * @name Common ROMAPI features info defines * @{ */ /*! @brief ROM has FLEXSPI NOR API. */ #define FSL_ROM_HAS_FLEXSPINOR_API (1) /*! @brief ROM has run bootloader API. */ #define FSL_ROM_HAS_RUNBOOTLOADER_API (1) /*! @brief ROM has FLEXSPI NOR get config API. */ #define FSL_ROM_FLEXSPINOR_API_HAS_FEATURE_GET_CONFIG (1) /*! @brief ROM has flash init API. */ #define FSL_ROM_FLEXSPINOR_API_HAS_FEATURE_FLASH_INIT (1) /*! @brief ROM has erase API. */ #define FSL_ROM_FLEXSPINOR_API_HAS_FEATURE_ERASE (1) /*! @brief ROM has erase sector API. */ #define FSL_ROM_FLEXSPINOR_API_HAS_FEATURE_ERASE_SECTOR (1) /*! @brief ROM has erase block API. */ #define FSL_ROM_FLEXSPINOR_API_HAS_FEATURE_ERASE_BLOCK (1) /*! @brief ROM has erase all API. */ #define FSL_ROM_FLEXSPINOR_API_HAS_FEATURE_ERASE_ALL (1) /*! @brief ROM has read API. */ #define FSL_ROM_FLEXSPINOR_API_HAS_FEATURE_READ (1) /*! @brief ROM has update lut API. */ #define FSL_ROM_FLEXSPINOR_API_HAS_FEATURE_UPDATE_LUT (1) /*! @brief ROM has FLEXSPI command API. */ #define FSL_ROM_FLEXSPINOR_API_HAS_FEATURE_CMD_XFER (1) /*@}*/ #define kROM_StatusGroup_FLEXSPINOR 201U /*!< ROM FLEXSPI NOR status group number.*/ #define FSL_ROM_FLEXSPI_LUT_SEQ(cmd0, pad0, op0, cmd1, pad1, op1) \ (FLEXSPI_LUT_OPERAND0(op0) | FLEXSPI_LUT_NUM_PADS0(pad0) | FLEXSPI_LUT_OPCODE0(cmd0) | FLEXSPI_LUT_OPERAND1(op1) | \ FLEXSPI_LUT_NUM_PADS1(pad1) | FLEXSPI_LUT_OPCODE1(cmd1)) /*! @brief Generate bit mask */ #define FSL_ROM_FLEXSPI_BITMASK(bit_offset) (1U << (bit_offset)) /*! @brief FLEXSPI memory config block related definitions */ #define FLEXSPI_CFG_BLK_TAG (0x42464346UL) /*!< ascii "FCFB" Big Endian */ #define FLEXSPI_CFG_BLK_VERSION (0x56010400UL) /*!< V1.4.0 */ #define CMD_SDR 0x01U #define CMD_DDR 0x21U #define RADDR_SDR 0x02U #define RADDR_DDR 0x22U #define CADDR_SDR 0x03U #define CADDR_DDR 0x23U #define MODE1_SDR 0x04U #define MODE1_DDR 0x24U #define MODE2_SDR 0x05U #define MODE2_DDR 0x25U #define MODE4_SDR 0x06U #define MODE4_DDR 0x26U #define MODE8_SDR 0x07U #define MODE8_DDR 0x27U #define WRITE_SDR 0x08U #define WRITE_DDR 0x28U #define READ_SDR 0x09U #define READ_DDR 0x29U #define LEARN_SDR 0x0AU #define LEARN_DDR 0x2AU #define DATSZ_SDR 0x0BU #define DATSZ_DDR 0x2BU #define DUMMY_SDR 0x0CU #define DUMMY_DDR 0x2CU #define DUMMY_RWDS_SDR 0x0DU #define DUMMY_RWDS_DDR 0x2DU #define JMP_ON_CS 0x1FU #define STOP 0U #define FLEXSPI_1PAD 0U #define FLEXSPI_2PAD 1U #define FLEXSPI_4PAD 2U #define FLEXSPI_8PAD 3U /*! * NOR LUT sequence index used for default LUT assignment. * * @note It will take effect if the lut sequences are not customized. */ #define NOR_CMD_LUT_SEQ_IDX_READ 0U /*!< READ LUT sequence id in lookupTable stored in config block */ #define NOR_CMD_LUT_SEQ_IDX_READSTATUS 1U /*!< Read Status LUT sequence id in lookupTable stored in config block */ #define NOR_CMD_LUT_SEQ_IDX_READSTATUS_XPI \ 2U /*!< Read status DPI/QPI/OPI sequence id in lookupTable stored in config block */ #define NOR_CMD_LUT_SEQ_IDX_WRITEENABLE 3U /*!< Write Enable sequence id in lookupTable stored in config block */ #define NOR_CMD_LUT_SEQ_IDX_WRITEENABLE_XPI \ 4U /*!< Write Enable DPI/QPI/OPI sequence id in lookupTable stored in config block */ #define NOR_CMD_LUT_SEQ_IDX_ERASESECTOR 5U /*!< Erase Sector sequence id in lookupTable stored in config block */ #define NOR_CMD_LUT_SEQ_IDX_READID 7U #define NOR_CMD_LUT_SEQ_IDX_ERASEBLOCK 8U /*!< Erase Block sequence id in lookupTable stored in config block */ #define NOR_CMD_LUT_SEQ_IDX_PAGEPROGRAM 9U /*!< Program sequence id in lookupTable stored in config block */ #define NOR_CMD_LUT_SEQ_IDX_CHIPERASE 11U /*!< Chip Erase sequence in lookupTable id stored in config block */ #define NOR_CMD_LUT_SEQ_IDX_READ_SFDP 13U /*!< Read SFDP sequence in lookupTable id stored in config block */ #define NOR_CMD_LUT_SEQ_IDX_RESTORE_NOCMD \ 14U /*!< Restore 0-4-4/0-8-8 mode sequence id in lookupTable stored in config block */ #define NOR_CMD_LUT_SEQ_IDX_EXIT_NOCMD \ 15U /*!< Exit 0-4-4/0-8-8 mode sequence id in lookupTable stored in config block */ /*! * @name Configuration Option * @{ */ /*! @brief Serial NOR Configuration Option. */ typedef struct _serial_nor_config_option { union { struct { uint32_t max_freq : 4; /*!< Maximum supported Frequency */ uint32_t misc_mode : 4; /*!< miscellaneous mode */ uint32_t quad_mode_setting : 4; /*!< Quad mode setting */ uint32_t cmd_pads : 4; /*!< Command pads */ uint32_t query_pads : 4; /*!< SFDP read pads */ uint32_t device_type : 4; /*!< Device type */ uint32_t option_size : 4; /*!< Option size, in terms of uint32_t, size = (option_size + 1) * 4 */ uint32_t tag : 4; /*!< Tag, must be 0x0E */ } B; uint32_t U; } option0; union { struct { uint32_t dummy_cycles : 8; /*!< Dummy cycles before read */ uint32_t status_override : 8; /*!< Override status register value during device mode configuration */ uint32_t pinmux_group : 4; /*!< The pinmux group selection */ uint32_t dqs_pinmux_group : 4; /*!< The DQS Pinmux Group Selection */ uint32_t drive_strength : 4; /*!< The Drive Strength of FlexSPI Pads */ uint32_t flash_connection : 4; /*!< Flash connection option: 0 - Single Flash connected to port A, 1 - Parallel mode, 2 - Single Flash connected to Port B */ } B; uint32_t U; } option1; } serial_nor_config_option_t; /*@}*/ /*! * @name Support for init FLEXSPI NOR configuration * @{ */ /*! @brief Flash Pad Definitions */ enum { kSerialFlash_1Pad = 1U, /*!< 1-wire communication */ kSerialFlash_2Pads = 2U, /*!< 2-wire communication */ kSerialFlash_4Pads = 4U, /*!< 4-wire communication */ kSerialFlash_8Pads = 8U, /*!< 8-wire communication */ }; /*! @brief FLEXSPI clock configuration type */ enum { kFLEXSPIClk_SDR, /*!< Clock configure for SDR mode */ kFLEXSPIClk_DDR, /*!< Clock configure for DDR mode */ }; /*! @brief FLEXSPI Read Sample Clock Source definition */ enum _flexspi_read_sample_clk { kFLEXSPIReadSampleClk_LoopbackInternally = 0U, /*!< FLEXSPI Read Sample Clock Source from the Internal loopback */ kFLEXSPIReadSampleClk_LoopbackFromDqsPad = 1U, /*!< FLEXSPI Read Sample Clock Source from the Dqs Pad loopback */ kFLEXSPIReadSampleClk_LoopbackFromSckPad = 2U, /*!< FLEXSPI Read Sample Clock Source from the Sck Pad loopback */ kFLEXSPIReadSampleClk_ExternalInputFromDqsPad = 3U, /*!< FLEXSPI Read Sample Clock Source from the External Input by the Dqs Pad */ }; /*! @brief Flash Type Definition */ enum { kFLEXSPIDeviceType_SerialNOR = 1U, /*!< Flash device is Serial NOR */ }; /*! @brief Flash Configuration Command Type */ enum { kDeviceConfigCmdType_Generic, /*!< Generic command, for example: configure dummy cycles, drive strength, etc. */ kDeviceConfigCmdType_QuadEnable, /*!< Quad Enable command */ kDeviceConfigCmdType_Spi2Xpi, /*!< Switch from SPI to DPI/QPI/OPI mode */ kDeviceConfigCmdType_Xpi2Spi, /*!< Switch from DPI/QPI/OPI to SPI mode */ kDeviceConfigCmdType_Spi2NoCmd, /*!< Switch to 0-4-4/0-8-8 mode */ kDeviceConfigCmdType_Reset, /*!< Reset device command */ }; /*! @brief Definitions for FLEXSPI Serial Clock Frequency */ enum _flexspi_serial_clk_freq { kFLEXSPISerialClk_NoChange = 0U, /*!< FlexSPI serial clock no changed */ kFLEXSPISerialClk_30MHz = 1U, /*!< FlexSPI serial clock 30MHz */ kFLEXSPISerialClk_50MHz = 2U, /*!< FlexSPI serial clock 50MHz */ kFLEXSPISerialClk_60MHz = 3U, /*!< FlexSPI serial clock 60MHz */ kFLEXSPISerialClk_75MHz = 4U, /*!< FlexSPI serial clock 75MHz */ kFLEXSPISerialClk_80MHz = 5U, /*!< FlexSPI serial clock 80MHz */ kFLEXSPISerialClk_100MHz = 6U, /*!< FlexSPI serial clock 100MHz */ kFLEXSPISerialClk_133MHz = 7U, /*!< FlexSPI serial clock 133MHz */ kFLEXSPISerialClk_166MHz = 8U, /*!< FlexSPI serial clock 166MHz */ }; /*! @brief Misc feature bit definitions */ enum { kFLEXSPIMiscOffset_DiffClkEnable = 0U, /*!< Bit for Differential clock enable */ kFLEXSPIMiscOffset_Ck2Enable = 1U, /*!< Bit for CK2 enable */ kFLEXSPIMiscOffset_ParallelEnable = 2U, /*!< Bit for Parallel mode enable */ kFLEXSPIMiscOffset_WordAddressableEnable = 3U, /*!< Bit for Word Addressable enable */ kFLEXSPIMiscOffset_SafeConfigFreqEnable = 4U, /*!< Bit for Safe Configuration Frequency enable */ kFLEXSPIMiscOffset_PadSettingOverrideEnable = 5U, /*!< Bit for Pad setting override enable */ kFLEXSPIMiscOffset_DdrModeEnable = 6U, /*!< Bit for DDR clock configuration indication. */ kFLEXSPIMiscOffset_UseValidTimeForAllFreq = 7U, /*!< Bit for DLLCR settings under all modes */ }; /*@}*/ /*! @brief Manufacturer ID */ enum { kSerialFlash_ISSI_ManufacturerID = 0x9DU, /*!< Manufacturer ID of the ISSI serial flash */ kSerialFlash_Adesto_ManufacturerID = 0x1F, /*!< Manufacturer ID of the Adesto Technologies serial flash*/ kSerialFlash_Winbond_ManufacturerID = 0xEFU, /*!< Manufacturer ID of the Winbond serial flash */ kSerialFlash_Cypress_ManufacturerID = 0x01U, /*!< Manufacturer ID for Cypress */ }; /*! @brief ROM FLEXSPI NOR flash status */ enum _flexspi_nor_status { kStatus_ROM_FLEXSPI_SequenceExecutionTimeout = MAKE_STATUS(kStatusGroup_FLEXSPI, 0), /*!< Status for Sequence Execution timeout */ kStatus_ROM_FLEXSPI_InvalidSequence = MAKE_STATUS(kStatusGroup_FLEXSPI, 1), /*!< Status for Invalid Sequence */ kStatus_ROM_FLEXSPI_DeviceTimeout = MAKE_STATUS(kStatusGroup_FLEXSPI, 2), /*!< Status for Device timeout */ kStatus_ROM_FLEXSPINOR_SFDP_NotFound = MAKE_STATUS(kROM_StatusGroup_FLEXSPINOR, 7), /*!< Status for SFDP read failure */ kStatus_ROM_FLEXSPINOR_Flash_NotFound = MAKE_STATUS(kROM_StatusGroup_FLEXSPINOR, 9), /*!< Status for Flash detection failure */ kStatus_FLEXSPINOR_DTRRead_DummyProbeFailed = MAKE_STATUS(kROM_StatusGroup_FLEXSPINOR, 10), /*!< Status for DDR Read dummy probe failure */ }; /*! * @name FLEXSPI NOR Configuration * @{ */ /*! @brief FLEXSPI LUT Sequence structure */ typedef struct _flexspi_lut_seq { uint8_t seqNum; /*!< Sequence Number, valid number: 1-16 */ uint8_t seqId; /*!< Sequence Index, valid number: 0-15 */ uint16_t reserved; } flexspi_lut_seq_t; /*! @brief FLEXSPI DLL time */ typedef struct { uint8_t time_100ps; /*!< Data valid time, in terms of 100ps */ uint8_t delay_cells; /*!< Data valid time, in terms of delay cells */ } flexspi_dll_time_t; /*! @brief FLEXSPI Memory Configuration Block */ typedef struct _flexspi_mem_config { uint32_t tag; /*!< [0x000-0x003] Tag, fixed value 0x42464346UL */ uint32_t version; /*!< [0x004-0x007] Version,[31:24] -'V', [23:16] - Major, [15:8] - Minor, [7:0] - bugfix */ uint32_t reserved0; /*!< [0x008-0x00b] Reserved for future use */ uint8_t readSampleClkSrc; /*!< [0x00c-0x00c] Read Sample Clock Source, valid value: 0/1/3 */ uint8_t csHoldTime; /*!< [0x00d-0x00d] Data hold time, default value: 3 */ uint8_t csSetupTime; /*!< [0x00e-0x00e] Date setup time, default value: 3 */ uint8_t columnAddressWidth; /*!< [0x00f-0x00f] Column Address with, for HyperBus protocol, it is fixed to 3, For Serial NAND, need to refer to datasheet */ uint8_t deviceModeCfgEnable; /*!< [0x010-0x010] Device Mode Configure enable flag, 1 - Enable, 0 - Disable */ uint8_t deviceModeType; /*!< [0x011-0x011] Specify the configuration command type:Quad Enable, DPI/QPI/OPI switch, Generic configuration, etc. */ uint16_t waitTimeCfgCommands; /*!< [0x012-0x013] Wait time for all configuration commands, unit: 100us, Used for DPI/QPI/OPI switch or reset command */ flexspi_lut_seq_t deviceModeSeq; /*!< [0x014-0x017] Device mode sequence info, [7:0] - LUT sequence id, [15:8] - LUt sequence number, [31:16] Reserved */ uint32_t deviceModeArg; /*!< [0x018-0x01b] Argument/Parameter for device configuration */ uint8_t configCmdEnable; /*!< [0x01c-0x01c] Configure command Enable Flag, 1 - Enable, 0 - Disable */ uint8_t configModeType[3]; /*!< [0x01d-0x01f] Configure Mode Type, similar as deviceModeTpe */ flexspi_lut_seq_t configCmdSeqs[3]; /*!< [0x020-0x02b] Sequence info for Device Configuration command, similar as deviceModeSeq */ uint32_t reserved1; /*!< [0x02c-0x02f] Reserved for future use */ uint32_t configCmdArgs[3]; /*!< [0x030-0x03b] Arguments/Parameters for device Configuration commands */ uint32_t reserved2; /*!< [0x03c-0x03f] Reserved for future use */ uint32_t controllerMiscOption; /*!< [0x040-0x043] Controller Misc Options, see Misc feature bit definitions for more details */ uint8_t deviceType; /*!< [0x044-0x044] Device Type: See Flash Type Definition for more details */ uint8_t sflashPadType; /*!< [0x045-0x045] Serial Flash Pad Type: 1 - Single, 2 - Dual, 4 - Quad, 8 - Octal */ uint8_t serialClkFreq; /*!< [0x046-0x046] Serial Flash Frequency, device specific definitions. See System Boot Chapter for more details */ uint8_t lutCustomSeqEnable; /*!< [0x047-0x047] LUT customization Enable, it is required if the program/erase cannot be done using 1 LUT sequence, currently, only applicable to HyperFLASH */ uint32_t reserved3[2]; /*!< [0x048-0x04f] Reserved for future use */ uint32_t sflashA1Size; /*!< [0x050-0x053] Size of Flash connected to A1 */ uint32_t sflashA2Size; /*!< [0x054-0x057] Size of Flash connected to A2 */ uint32_t sflashB1Size; /*!< [0x058-0x05b] Size of Flash connected to B1 */ uint32_t sflashB2Size; /*!< [0x05c-0x05f] Size of Flash connected to B2 */ uint32_t csPadSettingOverride; /*!< [0x060-0x063] CS pad setting override value */ uint32_t sclkPadSettingOverride; /*!< [0x064-0x067] SCK pad setting override value */ uint32_t dataPadSettingOverride; /*!< [0x068-0x06b] data pad setting override value */ uint32_t dqsPadSettingOverride; /*!< [0x06c-0x06f] DQS pad setting override value */ uint32_t timeoutInMs; /*!< [0x070-0x073] Timeout threshold for read status command */ uint32_t commandInterval; /*!< [0x074-0x077] CS deselect interval between two commands */ flexspi_dll_time_t dataValidTime[2]; /*!< [0x078-0x07b] CLK edge to data valid time for PORT A and PORT B */ uint16_t busyOffset; /*!< [0x07c-0x07d] Busy offset, valid value: 0-31 */ uint16_t busyBitPolarity; /*!< [0x07e-0x07f] Busy flag polarity, 0 - busy flag is 1 when flash device is busy, 1 - busy flag is 0 when flash device is busy */ uint32_t lookupTable[64]; /*!< [0x080-0x17f] Lookup table holds Flash command sequences */ flexspi_lut_seq_t lutCustomSeq[12]; /*!< [0x180-0x1af] Customizable LUT Sequences */ uint32_t reserved4[4]; /*!< [0x1b0-0x1bf] Reserved for future use */ } flexspi_mem_config_t; /*! @brief Serial NOR configuration block */ typedef struct _flexspi_nor_config { flexspi_mem_config_t memConfig; /*!< Common memory configuration info via FLEXSPI */ uint32_t pageSize; /*!< Page size of Serial NOR */ uint32_t sectorSize; /*!< Sector size of Serial NOR */ uint8_t ipcmdSerialClkFreq; /*!< Clock frequency for IP command */ uint8_t isUniformBlockSize; /*!< Sector/Block size is the same */ uint8_t isDataOrderSwapped; /*!< Data order (D0, D1, D2, D3) is swapped (D1,D0, D3, D2) */ uint8_t reserved0[1]; /*!< Reserved for future use */ uint8_t serialNorType; /*!< Serial NOR Flash type: 0/1/2/3 */ uint8_t needExitNoCmdMode; /*!< Need to exit NoCmd mode before other IP command */ uint8_t halfClkForNonReadCmd; /*!< Half the Serial Clock for non-read command: true/false */ uint8_t needRestoreNoCmdMode; /*!< Need to Restore NoCmd mode after IP command execution */ uint32_t blockSize; /*!< Block size */ uint32_t reserve2[11]; /*!< Reserved for future use */ } flexspi_nor_config_t; /*@}*/ /*! @brief FLEXSPI Operation Context */ typedef enum _flexspi_operation { kFLEXSPIOperation_Command, /*!< FLEXSPI operation: Only command, both TX and RX buffer are ignored. */ kFLEXSPIOperation_Config, /*!< FLEXSPI operation: Configure device mode, the TX FIFO size is fixed in LUT. */ kFLEXSPIOperation_Write, /*!< FLEXSPI operation: Write, only TX buffer is effective */ kFLEXSPIOperation_Read, /*!< FLEXSPI operation: Read, only Rx Buffer is effective. */ } flexspi_operation_t; #define kFLEXSPIOperation_End kFLEXSPIOperation_Read /*! @brief FLEXSPI Transfer Context */ typedef struct _flexspi_xfer { flexspi_operation_t operation; /*!< FLEXSPI operation */ uint32_t baseAddress; /*!< FLEXSPI operation base address */ uint32_t seqId; /*!< Sequence Id */ uint32_t seqNum; /*!< Sequence Number */ bool isParallelModeEnable; /*!< Is a parallel transfer */ uint32_t *txBuffer; /*!< Tx buffer */ uint32_t txSize; /*!< Tx size in bytes */ uint32_t *rxBuffer; /*!< Rx buffer */ uint32_t rxSize; /*!< Rx size in bytes */ } flexspi_xfer_t; /*! @brief convert the type for MISRA */ #define MISRA_CAST(to_type, to_var, from_type, from_var) \ do \ { \ union \ { \ to_type to_var_tmp; \ from_type from_var_tmp; \ } type_converter_var = {.from_var_tmp = (from_var)}; \ (to_var) = type_converter_var.to_var_tmp; \ } while (false) #ifdef __cplusplus extern "C" { #endif #if defined(FSL_FEATURE_BOOT_ROM_HAS_ROMAPI) && FSL_FEATURE_BOOT_ROM_HAS_ROMAPI /*! * @brief ROM API init * * Get the bootloader api entry address. */ void ROM_API_Init(void); /*! * @name Enter Bootloader * @{ */ #if defined(FSL_ROM_HAS_RUNBOOTLOADER_API) && FSL_ROM_HAS_RUNBOOTLOADER_API /*! * @brief Enter Bootloader. * * @param arg A pointer to the storage for the bootloader param. * refer to System Boot Chapter in device reference manual for details. */ void ROM_RunBootloader(void *arg); #endif /* FSL_ROM_HAS_RUNBOOTLOADER_API */ /*@}*/ /*! * @name GetConfig * @{ */ #if defined(FSL_ROM_FLEXSPINOR_API_HAS_FEATURE_GET_CONFIG) && FSL_ROM_FLEXSPINOR_API_HAS_FEATURE_GET_CONFIG /*! * @brief Get FLEXSPI NOR Configuration Block based on specified option. * * @param instance storage the instance of FLEXSPI. * @param config A pointer to the storage for the driver runtime state. * @param option A pointer to the storage Serial NOR Configuration Option Context. * * @retval kStatus_Success Api was executed successfully. * @retval kStatus_InvalidArgument A invalid argument is provided. * @retval kStatus_ROM_FLEXSPI_InvalidSequence A invalid Sequence is provided. * @retval kStatus_ROM_FLEXSPI_SequenceExecutionTimeout Sequence Execution timeout. * @retval kStatus_ROM_FLEXSPI_DeviceTimeout the device timeout */ status_t ROM_FLEXSPI_NorFlash_GetConfig(uint32_t instance, flexspi_nor_config_t *config, serial_nor_config_option_t *option); #endif /* FSL_ROM_FLEXSPINOR_API_HAS_FEATURE_GET_CONFIG */ /*! * @name Initialization * @{ */ /*! * @brief Initialize Serial NOR devices via FLEXSPI * * This function checks and initializes the FLEXSPI module for the other FLEXSPI APIs. * * @param instance storage the instance of FLEXSPI. * @param config A pointer to the storage for the driver runtime state. * * @retval kStatus_Success Api was executed successfully. * @retval kStatus_InvalidArgument A invalid argument is provided. * @retval kStatus_ROM_FLEXSPI_InvalidSequence A invalid Sequence is provided. * @retval kStatus_ROM_FLEXSPI_SequenceExecutionTimeout Sequence Execution timeout. * @retval kStatus_ROM_FLEXSPI_DeviceTimeout the device timeout */ status_t ROM_FLEXSPI_NorFlash_Init(uint32_t instance, flexspi_nor_config_t *config); /*@}*/ /*! * @name Programming * @{ */ /*! * @brief Program data to Serial NOR via FLEXSPI. * * This function programs the NOR flash memory with the dest address for a given * flash area as determined by the dst address and the length. * * @param instance storage the instance of FLEXSPI. * @param config A pointer to the storage for the driver runtime state. * @param dst_addr A pointer to the desired flash memory to be programmed. * @note It is recommended that use page aligned access; * If the dst_addr is not aligned to page, the driver automatically * aligns address down with the page address. * @param src A pointer to the source buffer of data that is to be programmed * into the NOR flash. * * @retval kStatus_Success Api was executed successfully. * @retval kStatus_InvalidArgument A invalid argument is provided. * @retval kStatus_ROM_FLEXSPI_InvalidSequence A invalid Sequence is provided. * @retval kStatus_ROM_FLEXSPI_SequenceExecutionTimeout Sequence Execution timeout. * @retval kStatus_ROM_FLEXSPI_DeviceTimeout the device timeout */ status_t ROM_FLEXSPI_NorFlash_ProgramPage(uint32_t instance, flexspi_nor_config_t *config, uint32_t dst_addr, const uint32_t *src); /*@}*/ /*! * @name Reading * @{ */ #if defined(FSL_ROM_FLEXSPINOR_API_HAS_FEATURE_READ) && FSL_ROM_FLEXSPINOR_API_HAS_FEATURE_READ /*! * @brief Read data from Serial NOR via FLEXSPI. * * This function read the NOR flash memory with the start address for a given * flash area as determined by the dst address and the length. * * @param instance storage the instance of FLEXSPI. * @param config A pointer to the storage for the driver runtime state. * @param dst A pointer to the dest buffer of data that is to be read from the NOR flash. * @note It is recommended that use page aligned access; * If the dstAddr is not aligned to page, the driver automatically * aligns address down with the page address. * @param start The start address of the desired NOR flash memory to be read. * @param lengthInBytes The length, given in bytes to be read. * * @retval kStatus_Success Api was executed successfully. * @retval kStatus_InvalidArgument A invalid argument is provided. * @retval kStatus_ROM_FLEXSPI_InvalidSequence A invalid Sequence is provided. * @retval kStatus_ROM_FLEXSPI_SequenceExecutionTimeout Sequence Execution timeout. * @retval kStatus_ROM_FLEXSPI_DeviceTimeout the device timeout */ status_t ROM_FLEXSPI_NorFlash_Read( uint32_t instance, flexspi_nor_config_t *config, uint32_t *dst, uint32_t start, uint32_t lengthInBytes); #endif /* FSL_ROM_FLEXSPINOR_API_HAS_FEATURE_READ */ /*@}*/ /*! * @name Erasing * @{ */ /*! * @brief Erase Flash Region specified by address and length * * This function erases the appropriate number of flash sectors based on the * desired start address and length. * * @param instance storage the index of FLEXSPI. * @param config A pointer to the storage for the driver runtime state. * @param start The start address of the desired NOR flash memory to be erased. * @note It is recommended that use sector-aligned access nor device; * If dstAddr is not aligned with the sector,the driver automatically * aligns address down with the sector address. * @param length The length, given in bytes to be erased. * @note It is recommended that use sector-aligned access nor device; * If length is not aligned with the sector,the driver automatically * aligns up with the sector. * @retval kStatus_Success Api was executed successfully. * @retval kStatus_InvalidArgument A invalid argument is provided. * @retval kStatus_ROM_FLEXSPI_InvalidSequence A invalid Sequence is provided. * @retval kStatus_ROM_FLEXSPI_SequenceExecutionTimeout Sequence Execution timeout. * @retval kStatus_ROM_FLEXSPI_DeviceTimeout the device timeout */ status_t ROM_FLEXSPI_NorFlash_Erase(uint32_t instance, flexspi_nor_config_t *config, uint32_t start, uint32_t length); #if defined(FSL_ROM_FLEXSPINOR_API_HAS_FEATURE_ERASE_SECTOR) && FSL_ROM_FLEXSPINOR_API_HAS_FEATURE_ERASE_SECTOR /*! * @brief Erase one sector specified by address * * This function erases one of NOR flash sectors based on the desired address. * * @param instance storage the index of FLEXSPI. * @param config A pointer to the storage for the driver runtime state. * @param start The start address of the desired NOR flash memory to be erased. * @note It is recommended that use sector-aligned access nor device; * If dstAddr is not aligned with the sector, the driver automatically * aligns address down with the sector address. * * @retval kStatus_Success Api was executed successfully. * @retval kStatus_InvalidArgument A invalid argument is provided. * @retval kStatus_ROM_FLEXSPI_InvalidSequence A invalid Sequence is provided. * @retval kStatus_ROM_FLEXSPI_SequenceExecutionTimeout Sequence Execution timeout. * @retval kStatus_ROM_FLEXSPI_DeviceTimeout the device timeout */ status_t ROM_FLEXSPI_NorFlash_EraseSector(uint32_t instance, flexspi_nor_config_t *config, uint32_t start); #endif /* FSL_ROM_FLEXSPINOR_API_HAS_FEATURE_ERASE_SECTOR */ #if defined(FSL_ROM_FLEXSPINOR_API_HAS_FEATURE_ERASE_BLOCK) && FSL_ROM_FLEXSPINOR_API_HAS_FEATURE_ERASE_BLOCK /*! * @brief Erase one block specified by address * * This function erases one block of NOR flash based on the desired address. * * @param instance storage the index of FLEXSPI. * @param config A pointer to the storage for the driver runtime state. * @param start The start address of the desired NOR flash memory to be erased. * @note It is recommended that use block-aligned access nor device; * If dstAddr is not aligned with the block, the driver automatically * aligns address down with the block address. * * @retval kStatus_Success Api was executed successfully. * @retval kStatus_InvalidArgument A invalid argument is provided. * @retval kStatus_ROM_FLEXSPI_InvalidSequence A invalid Sequence is provided. * @retval kStatus_ROM_FLEXSPI_SequenceExecutionTimeout Sequence Execution timeout. * @retval kStatus_ROM_FLEXSPI_DeviceTimeout the device timeout */ status_t ROM_FLEXSPI_NorFlash_EraseBlock(uint32_t instance, flexspi_nor_config_t *config, uint32_t start); #endif /* FSL_ROM_FLEXSPINOR_API_HAS_FEATURE_ERASE_BLOCK */ #if defined(FSL_ROM_FLEXSPINOR_API_HAS_FEATURE_ERASE_ALL) && FSL_ROM_FLEXSPINOR_API_HAS_FEATURE_ERASE_ALL /*! * @brief Erase all the Serial NOR devices connected on FLEXSPI. * * @param instance storage the instance of FLEXSPI. * @param config A pointer to the storage for the driver runtime state. * * @retval kStatus_Success Api was executed successfully. * @retval kStatus_InvalidArgument A invalid argument is provided. * @retval kStatus_ROM_FLEXSPI_InvalidSequence A invalid Sequence is provided. * @retval kStatus_ROM_FLEXSPI_SequenceExecutionTimeout Sequence Execution timeout. * @retval kStatus_ROM_FLEXSPI_DeviceTimeout the device timeout */ status_t ROM_FLEXSPI_NorFlash_EraseAll(uint32_t instance, flexspi_nor_config_t *config); #endif /* FSL_ROM_FLEXSPINOR_API_HAS_FEATURE_ERASE_ALL */ /*@}*/ /*! * @name Command * @{ */ #if defined(FSL_ROM_FLEXSPINOR_API_HAS_FEATURE_CMD_XFER) && FSL_ROM_FLEXSPINOR_API_HAS_FEATURE_CMD_XFER /*! * @brief FLEXSPI command * * This function is used to perform the command write sequence to the NOR device. * * @param instance storage the index of FLEXSPI. * @param xfer A pointer to the storage FLEXSPI Transfer Context. * * @retval kStatus_Success Api was executed successfully. * @retval kStatus_InvalidArgument A invalid argument is provided. * @retval kStatus_ROM_FLEXSPI_InvalidSequence A invalid Sequence is provided. * @retval kStatus_ROM_FLEXSPI_SequenceExecutionTimeout Sequence Execution timeout. */ status_t ROM_FLEXSPI_NorFlash_CommandXfer(uint32_t instance, flexspi_xfer_t *xfer); #endif /* FSL_ROM_FLEXSPINOR_API_HAS_FEATURE_CMD_XFER */ /*@}*/ /*! * @name UpdateLut * @{ */ #if defined(FSL_ROM_FLEXSPINOR_API_HAS_FEATURE_UPDATE_LUT) && FSL_ROM_FLEXSPINOR_API_HAS_FEATURE_UPDATE_LUT /*! * @brief Configure FLEXSPI Lookup table * * @param instance storage the index of FLEXSPI. * @param seqIndex storage the sequence Id. * @param lutBase A pointer to the look-up-table for command sequences. * @param seqNumber storage sequence number. * * @retval kStatus_Success Api was executed successfully. * @retval kStatus_InvalidArgument A invalid argument is provided. * @retval kStatus_ROM_FLEXSPI_InvalidSequence A invalid Sequence is provided. * @retval kStatus_ROM_FLEXSPI_SequenceExecutionTimeout Sequence Execution timeout. */ status_t ROM_FLEXSPI_NorFlash_UpdateLut(uint32_t instance, uint32_t seqIndex, const uint32_t *lutBase, uint32_t seqNumber); #endif /* FSL_ROM_FLEXSPINOR_API_HAS_FEATURE_UPDATE_LUT */ /*@}*/ /*! * @name Device status * @{ */ /*! * @brief Wait until device is idle. * * @param instance Indicates the index of FLEXSPI. * @param config A pointer to the storage for the driver runtime state * @param isParallelMode Indicates whether NOR flash is in parallel mode. * @param address Indicates the operation(erase/program/read) address for serial NOR flash. * * @retval kStatus_Success Api was executed successfully. * @retval kStatus_InvalidArgument A invalid argument is provided. * @retval kStatus_ROM_FLEXSPI_SequenceExecutionTimeout Sequence Execution timeout. * @retval kStatus_ROM_FLEXSPI_InvalidSequence A invalid Sequence is provided. * @retval kStatus_ROM_FLEXSPI_DeviceTimeout Device timeout. */ status_t ROM_FLEXSPI_NorFlash_WaitBusy(uint32_t instance, flexspi_nor_config_t *config, bool isParallelMode, uint32_t address); /*@}*/ /*! * @name ClearCache * @{ */ /*! * @name ClearCache * @{ */ /*! * @brief Software reset for the FLEXSPI logic. * * This function sets the software reset flags for both AHB and buffer domain and * resets both AHB buffer and also IP FIFOs. * * @param instance storage the index of FLEXSPI. */ void ROM_FLEXSPI_NorFlash_ClearCache(uint32_t instance); /*@}*/ #endif /* FSL_FEATURE_BOOT_ROM_HAS_ROMAPI */ #ifdef __cplusplus } #endif /*! @}*/ #endif /* _FSL_ROMAPI_H_ */