menu "Hardware Drivers Config"

    config SOC_R9A07G084
        bool
        select SOC_SERIES_R9A07G0
        select RT_USING_COMPONENTS_INIT
        select RT_USING_USER_MAIN
        default y

    menu "Onboard Peripheral Drivers"

        config BSP_USING_ETHERCAT_EOE
            bool "Enable EtherCAT EOE example"
            select BSP_USING_ETH
            default n
            if BSP_USING_ETHERCAT_EOE
                config RT_LWIP_IPADDR
                    string "set static ip address for eoe slaver"
                    default "192.168.10.100"
                config RT_LWIP_GWADDR
                    string "set static gateway address for eoe slaver"
                    default "192.168.10.1"
                config RT_LWIP_MSKADDR
                    string "set static mask address for eoe slaver"
                    default "255.255.255.0"
            endif

    endmenu

    menu "On-chip Peripheral Drivers"

        rsource "../../libraries/HAL_Drivers/Kconfig"

        menuconfig BSP_USING_UART
            bool "Enable UART"
            default y
            select RT_USING_SERIAL
            select RT_USING_SERIAL_V2
            if BSP_USING_UART

                menuconfig BSP_USING_UART0
                    bool "Enable UART0"
                    default n
                    if BSP_USING_UART0
                        config BSP_UART0_RX_USING_DMA
                            bool "Enable UART0 RX DMA"
                            depends on BSP_USING_UART0 && RT_SERIAL_USING_DMA
                            default n

                        config BSP_UART0_TX_USING_DMA
                            bool "Enable UART0 TX DMA"
                            depends on BSP_USING_UART0 && RT_SERIAL_USING_DMA
                            default n

                        config BSP_UART0_RX_BUFSIZE
                            int "Set UART0 RX buffer size"
                            range 64 65535
                            depends on RT_USING_SERIAL_V2
                            default 256

                        config BSP_UART0_TX_BUFSIZE
                            int "Set UART0 TX buffer size"
                            range 0 65535
                            depends on RT_USING_SERIAL_V2
                            default 0
                    endif
            endif

        menuconfig BSP_USING_ADC
            bool "Enable ADC"
            default n
            select RT_USING_ADC
            if BSP_USING_ADC
                config BSP_USING_ADC1
                    bool "Enable ADC1"
                    default n
            endif

        menuconfig BSP_USING_CANFD
            bool "Enable CANFD"
            default n
            select RT_USING_CAN
            select RT_CAN_USING_CANFD
            if BSP_USING_CANFD
                config BSP_USING_CANFD0
                    bool "Enable CANFD0"
                    default n
            endif

        menuconfig BSP_USING_I2C
            bool "Enable I2C BUS"
            default n
            select RT_USING_I2C
            select RT_USING_I2C_BITOPS
            select RT_USING_PIN
            if BSP_USING_I2C
                config BSP_USING_HW_I2C
                    bool "Enable Hardware I2C BUS"
                    default n
                if BSP_USING_HW_I2C
                    config BSP_USING_HW_I2C0
                        bool "Enable Hardware I2C0 BUS"
                        default n
                endif
                if BSP_USING_HW_I2C
                    config BSP_USING_HW_I2C1
                        bool "Enable Hardware I2C1 BUS"
                        default n
                endif
            if !BSP_USING_HW_I2C
                    menuconfig BSP_USING_I2C1
                        bool "Enable I2C1 BUS (software simulation)"
                        default y
                        if BSP_USING_I2C1
                            config BSP_I2C1_SCL_PIN
                                hex "i2c1 scl pin number"
                                range 0x0000 0x0B0F
                                default 0x0B03
                            config BSP_I2C1_SDA_PIN
                                hex "I2C1 sda pin number"
                                range 0x0000 0x0B0F
                                default 0x050E
                    endif
                endif
            endif

        menuconfig BSP_USING_SPI
            bool "Enable SPI BUS"
            default n
            select RT_USING_SPI
            if BSP_USING_SPI 
                config BSP_USING_SPI0
                    bool "Enable SPI0 BUS"
                    default n
                config BSP_USING_SPI1
                    bool "Enable SPI1 BUS"
                    default n
                config BSP_USING_SPI2
                    bool "Enable SPI2 BUS"
                    default n
            endif

        menuconfig BSP_USING_TIM
	        bool "Enable timer"
	        default n
	        select RT_USING_HWTIMER
	        if BSP_USING_TIM
	            config BSP_USING_TIM0
	                bool "Enable TIM0"
	                default n
	            config BSP_USING_TIM1
	                bool "Enable TIM1"
	                default n
	        endif

        config BSP_USING_ETH
            bool "Enable Ethernet"
            select RT_USING_SAL
            select RT_USING_LWIP
            select RT_USING_NETDEV
            default n

    endmenu
    
    menu "Board extended module Drivers"
         menuconfig BSP_USING_RW007
                bool "Enable RW007"
                default n
                select PKG_USING_RW007
                select BSP_USING_SPI
                select BSP_USING_SPI2
                select RT_USING_MEMPOOL
                select RW007_NOT_USE_EXAMPLE_DRIVERS

            if BSP_USING_RW007
                config RA_RW007_SPI_BUS_NAME
                    string "RW007 BUS NAME"
                    default "spi2"

                config RA_RW007_CS_PIN
                    hex "(HEX)CS pin index"
                    default 0x1207

                config RA_RW007_BOOT0_PIN
                    hex "(HEX)BOOT0 pin index (same as spi clk pin)"
                    default 0x1204

                config RA_RW007_BOOT1_PIN
                    hex "(HEX)BOOT1 pin index (same as spi cs pin)"
                    default 0x1207

                config RA_RW007_INT_BUSY_PIN
                    hex "(HEX)INT/BUSY pin index"
                    default 0x1102

                config RA_RW007_RST_PIN
                    hex "(HEX)RESET pin index"
                    default 0x1706
            endif
    endmenu
endmenu