menu "Hardware Drivers Config" menu "On-chip Peripheral Drivers" source "$(BSP_DIR)/../libraries/m480/rtt_port/Kconfig" endmenu menu "On-board Peripheral Drivers" config BSP_USING_NULINKME bool "Enable UART0 for RTT Console(uart0)" select BSP_USING_UART select BSP_USING_UART0 default y config BOARD_USING_IP101GR bool "Enable ethernet phy supporting(over emac/mdio)" select BSP_USING_EMAC default n config BOARD_USING_ESP8266 bool "ESP8266 Wi-Fi module supporting(over uart1)" select BSP_USING_UART select BSP_USING_UART1 select BSP_USING_UART1_RX_DMA select BSP_USING_UART1_TX_DMA select PKG_USING_AT_DEVICE select AT_DEVICE_USING_ESP8266 select AT_DEVICE_ESP8266_INIT_ASYN default n config BOARD_USING_BMX055 bool "BMX055 9-axis sensor(over i2c2)" select NU_PKG_USING_BMX055 select BSP_USING_I2C2 default n config BOARD_USING_NAU88L25 bool "NAU88L25 Audio Codec supporting(over i2s, i2c2)" select NU_PKG_USING_NAU88L25 select BSP_USING_I2C2 select BSP_USING_I2S select BSP_USING_I2S0 default n config BOARD_USING_STORAGE_SDCARD bool "SDCARD supporting(over sdh0)" select BSP_USING_SDH select BSP_USING_SDH0 default n config BOARD_USING_STORAGE_SPIFLASH bool "SPIFLASH supporting(over qspi0)" select BSP_USING_QSPI select BSP_USING_QSPI0 default y config BOARD_USING_USB_D_H bool "Enable USB Device or Host function" help Choose this option if you need USB function. if BOARD_USING_USB_D_H choice prompt "Select FS/HS USB Ports" config BOARD_USING_HSUSBD select BSP_USING_HSUSBD bool "Enable HSUSBD(over USB2.0)" help Choose this option if you need HSUSBD function mode. config BOARD_USING_HSUSBD_USBH select BSP_USING_USBH select BSP_USING_HSUSBD bool "Enable HSUSBD(over USB2.0) and USBH(over USB1.1)" help Choose this option if you need HSUSBD and USBH function mode at the same time. config BOARD_USING_HSUSBH select BSP_USING_HSUSBH bool "Enable HSUSBH(over USB2.0)" help Choose this option if you need HSUSBH function mode. config BOARD_USING_HSUSBH_USBD select BSP_USING_HSUSBH select BSP_USING_USBD bool "Enable HSUSBH(over USB2.0) and USBD(over USB1.1)" help Choose this option if you need HSUSBH and USBD function mode at the same time. config BOARD_USING_HSOTG select BSP_USING_HSOTG bool "Enable HSOTG(over USB2.0)" help Choose this option if you need HSOTG function mode. endchoice endif endmenu menu "Board extended module drivers" config BOARD_USING_MAX31875 bool "MAX31875 Temperature sensor(over i2c1)" select NU_PKG_USING_MAX31875 select BSP_USING_I2C1 default n config BOARD_USING_LCD_ILI9341 bool "LCD ILI9341 (over spi2)" select RT_USING_TOUCH select BSP_USING_SPI2 select BSP_USING_EADC select BSP_USING_EADC0 select NU_PKG_USING_ADC_TOUCH select NU_PKG_USING_ADC_TOUCH_SW select NU_PKG_USING_ILI9341 select NU_PKG_USING_ILI9341_SPI select NU_PKG_ILI9341_WITH_OFFSCREEN_FRAMEBUFFER select NU_PKG_ILI9341_HORIZONTAL default n if BOARD_USING_LCD_ILI9341 config BOARD_USING_ILI9341_PIN_BACKLIGHT int "Specify the pin index of backlight pin index" range 0 127 default 69 config BOARD_USING_ILI9341_PIN_RESET int "Specify the pin index of reset pin index" range 0 127 default 19 config BOARD_USING_ILI9341_PIN_DC int "Specify the pin index of data&command switching" range 0 127 default 18 endif endmenu source "$(BSP_DIR)/../libraries/nu_packages/Kconfig" endmenu