//***************************************************************************** // // am_hal_ctimer.c //! @file //! //! @brief Functions for interfacing with the Counter/Timer module. //! //! @addtogroup ctimer2 Counter/Timer (CTIMER) //! @ingroup apollo2hal //! @{ // //***************************************************************************** //***************************************************************************** // // Copyright (c) 2017, Ambiq Micro // All rights reserved. // // Redistribution and use in source and binary forms, with or without // modification, are permitted provided that the following conditions are met: // // 1. Redistributions of source code must retain the above copyright notice, // this list of conditions and the following disclaimer. // // 2. Redistributions in binary form must reproduce the above copyright // notice, this list of conditions and the following disclaimer in the // documentation and/or other materials provided with the distribution. // // 3. Neither the name of the copyright holder nor the names of its // contributors may be used to endorse or promote products derived from this // software without specific prior written permission. // // THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS "AS IS" // AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE // IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE // ARE DISCLAIMED. IN NO EVENT SHALL THE COPYRIGHT HOLDER OR CONTRIBUTORS BE // LIABLE FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR // CONSEQUENTIAL DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF // SUBSTITUTE GOODS OR SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS // INTERRUPTION) HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN // CONTRACT, STRICT LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) // ARISING IN ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE // POSSIBILITY OF SUCH DAMAGE. // // This is part of revision 1.2.11 of the AmbiqSuite Development Package. // //***************************************************************************** #include #include #include "am_mcu_apollo.h" //***************************************************************************** // // Address space distance between timer configuration registers. // //***************************************************************************** #define MAX_CTIMERS 4 #define TIMER_OFFSET (AM_REG_CTIMER_TMR1_O - AM_REG_CTIMER_TMR0_O) #define CTIMER_CMPR_OFFSET (AM_REG_CTIMER_CMPRB0_O - AM_REG_CTIMER_CMPRA0_O) //***************************************************************************** // // Adjacency check // // This is related to the timer read workaround. This macro checks to see if // the two supplied count values are within one "tick" of eachother. It should // still pass in the event of a timer rollover. // //***************************************************************************** //! Timer read workaround: Do count values differ by one tick or less. #define adjacent(A, B) (((A) == (B)) || (((A) + 1) == (B)) || ((B) == 0)) //***************************************************************************** // //! Array of function pointers for handling CTimer interrupts. // //***************************************************************************** am_hal_ctimer_handler_t am_hal_ctimer_ppfnHandlers[16]; //***************************************************************************** // // Static function for reading the timer value. // //***************************************************************************** #if defined(__GNUC_STDC_INLINE__) __attribute__((naked)) static void back2back_reads(uint32_t u32TimerAddr, uint32_t u32Data[]) { // u32TimerAddr = address of the timer to be read. // u32Data[] is a pointer to a 3 word data array provided by the caller. __asm ( // Do 3 back-to-back reads of the register " push {r4}\n" // Save r4 " push {r1}\n" // Save the data array ptr for later " mov r2, r0\n" // Get Timer Addr " mrs r4, PRIMASK\n" // Save PRIMASK " cpsid i\n" // __disable_irq() " nop\n" // Give the disable a cycle to take affect (but almost certainly not really needed) " ldr r0, [r2, #0]\n" // Get TMRn register value " ldr r1, [r2, #0]\n" // Get TMRn register value again " ldr r3, [r2, #0]\n" // Get TMRn register value for a third time " msr PRIMASK, r4\n" // Restore PRIMASK " pop {r2}\n" // Get the array ptr " str r0, [r2, #0]\n" // Store register value to variable " str r1, [r2, #4]\n" // Store register value to variable " str r3, [r2, #8]\n" // Store register value to variable " pop {r4}\n" // restore r4 " bx lr\n" ); } #elif defined(__ARMCC_VERSION) __asm static uint32_t back2back_reads( uint32_t u32TimerAddr, uint32_t u32Data[]) { push {r4} // Save r4 push {r1} // Save the data array ptr for later mov r2, r0 // Get Timer Addr mrs r4, PRIMASK // Save PRIMASK cpsid i // __disable_irq() nop // Give the disable a cycle to take affect (but almost certainly not really needed) ldr r0, [r2, #0] // Get TMRn register value ldr r1, [r2, #0] // Get TMRn register value again ldr r3, [r2, #0] // Get TMRn register value for a third time msr PRIMASK, r4 // Restore PRIMASK pop {r2} // Get the array ptr str r0, [r2, #0] // Store register value to variable str r1, [r2, #4] // Store register value to variable str r3, [r2, #8] // Store register value to variable pop {r4} // Restore r4 bx lr } #elif defined(__IAR_SYSTEMS_ICC__) #pragma diag_suppress = Pe940 // Suppress IAR compiler warning about missing // return statement on a non-void function __stackless static uint32_t back2back_reads( uint32_t u32TimerAddr, uint32_t u32Data[]) { __asm(" push {r4}"); // Save r4 __asm(" push {r1}"); // Save the data array ptr for later __asm(" mov r2, r0"); // Get Timer Addr __asm(" mrs r4, PRIMASK"); // Save PRIMASK" __asm(" cpsid i"); // __disable_irq() __asm(" nop"); // Give the disable a cycle to take affect (but almost certainly not really needed) __asm(" ldr r0, [r2, #0]"); // Get TMRn register value __asm(" ldr r1, [r2, #0]"); // Get TMRn register value again __asm(" ldr r3, [r2, #0]"); // Get TMRn register value for a third time __asm(" msr PRIMASK, r4"); // Restore PRIMASK __asm(" pop {r2}"); // Get the array ptr __asm(" str r0, [r2, #0]"); // Store register value to variable __asm(" str r1, [r2, #4]"); // Store register value to variable __asm(" str r3, [r2, #8]"); // Store register value to variable __asm(" pop {r4}"); // Restore r4 __asm(" bx lr"); } #pragma diag_default = Pe940 // Restore IAR compiler warning #endif //***************************************************************************** // //! @brief Check to see if the given CTimer is using the HFRC //! //! @note Calls to this function should be from inside a critical section. //! //! @return None. // //***************************************************************************** static bool ctimer_source_hfrc(uint32_t ui32CtimerNum) { uint32_t *pui32ConfigReg; uint32_t ui32TimerASrc, ui32TimerBSrc; // // Find the correct register to write. // pui32ConfigReg = (uint32_t *)(AM_REG_CTIMERn(0) + AM_REG_CTIMER_CTRL0_O + (ui32CtimerNum * TIMER_OFFSET)); // // Determine if this timer is using HFRC as the clock source. // The value we are looking for is HFRC_DIV4 to HFRC_DIV4K. // Get the clock sources and 0-base the extracted value. // ui32TimerASrc = AM_BFX(CTIMER, CTRL0, TMRA0CLK, *pui32ConfigReg) - AM_ENUMX(CTIMER, CTRL0, TMRA0CLK, HFRC_DIV4); ui32TimerBSrc = AM_BFX(CTIMER, CTRL0, TMRB0CLK, *pui32ConfigReg) - AM_ENUMX(CTIMER, CTRL0, TMRB0CLK, HFRC_DIV4); // // If the source value is 0 to (HFRC_DIV4K - HFRC_DIV4), then it's HFRC. // if ( (ui32TimerASrc <= (AM_ENUMX(CTIMER, CTRL0, TMRA0CLK, HFRC_DIV4K) - AM_ENUMX(CTIMER, CTRL0, TMRA0CLK, HFRC_DIV4))) || (ui32TimerBSrc <= (AM_ENUMX(CTIMER, CTRL0, TMRB0CLK, HFRC_DIV4K) - AM_ENUMX(CTIMER, CTRL0, TMRB0CLK, HFRC_DIV4))) ) { return true; } else { return false; } } // ctimer_source_hfrc() //***************************************************************************** // // @brief Check to see if any of the CTimers or STimer are using the HFRC. // // This function should be used to check if the HFRC is being used in order // to correctly establish power related settings. // // Note - Calls to this function should be from inside a critical section. // //! @return None. // //***************************************************************************** static bool timers_use_hfrc(void) { uint32_t ui32TimerASrc, ui32CtimerNum; // // Check STimer to see if it is using HFRC. // ui32TimerASrc = AM_BFR(CTIMER, STCFG, CLKSEL); if ( (ui32TimerASrc == AM_REG_CTIMER_STCFG_CLKSEL_HFRC_DIV16) || (ui32TimerASrc == AM_REG_CTIMER_STCFG_CLKSEL_HFRC_DIV256) ) { return true; } // // Check the CTimers to see if any are using HFRC as their clock source. // for ( ui32CtimerNum = 0; ui32CtimerNum < MAX_CTIMERS; ui32CtimerNum++ ) { if ( ctimer_source_hfrc(ui32CtimerNum) ) { return true; } } return false; } // timers_use_hfrc() //***************************************************************************** // //! @brief Convenience function for responding to CTimer interrupts. //! //! @param ui32Status is the interrupt status as returned by //! am_hal_ctimer_int_status_get() //! //! This function may be called from am_ctimer_isr() to read the status of //! the CTimer interrupts, determine which source caused the most recent //! interrupt, and call an interrupt handler function to respond. The interrupt //! handler to be called must be first registered with the //! am_hal_ctimer_int_register() function. //! //! In the event that multiple sources are active, the corresponding //! interrupt handlers will be called in numerical order based on interrupt def. //! //! @return None. // //***************************************************************************** void am_hal_ctimer_int_service(uint32_t ui32Status) { uint32_t ui32Clz; am_hal_ctimer_handler_t pfnHandler; ui32Status &= 0xFFFF; while ( ui32Status ) { // // Pick one of any remaining active interrupt bits // #ifdef __IAR_SYSTEMS_ICC__ ui32Clz = __CLZ(ui32Status); #else ui32Clz = __builtin_clz(ui32Status); #endif // // Turn off the bit we picked in the working copy // ui32Status &= ~(0x80000000 >> ui32Clz); // // Check the bit handler table to see if there is an interrupt handler // registered for this particular bit. // pfnHandler = am_hal_ctimer_ppfnHandlers[31 - ui32Clz]; if ( pfnHandler ) { // // If we found an interrupt handler routine, call it now. // pfnHandler(); } } } // am_hal_ctimer_int_service() //***************************************************************************** // //! @brief Register an interrupt handler for CTimer. //! //! @param ui32Interrupt - interrupt number to assign this interrupt handler to. //! @param pfnHandler - Function to call when this interrupt is received. //! //! This function allows the caller to specify a function that should be called //! any time a Ctimer interrupt is received. Registering an //! interrupt handler using this function adds the function pointer to an array //! in SRAM. This interrupt handler will be called by am_hal_ctimer_int_service() //! whenever the ui32Status parameter indicates that the corresponding interrupt. //! //! To remove an interrupt handler that has already been registered, the //! pfnHandler parameter may be set to zero. //! //! @note This function will not have any effect unless the //! am_hal_ctimer_int_service() function is being used. //! //! @return None. // //***************************************************************************** void am_hal_ctimer_int_register(uint32_t ui32Interrupt, am_hal_ctimer_handler_t pfnHandler) { uint32_t intIdx = 0; // // Check to make sure the interrupt number is valid. (Debug builds only) // switch (ui32Interrupt) { case AM_REG_CTIMER_INTEN_CTMRA0C0INT_M: intIdx = AM_REG_CTIMER_INTEN_CTMRA0C0INT_S; break; case AM_REG_CTIMER_INTEN_CTMRB0C0INT_M: intIdx = AM_REG_CTIMER_INTEN_CTMRB0C0INT_S; break; case AM_REG_CTIMER_INTEN_CTMRA1C0INT_M: intIdx = AM_REG_CTIMER_INTEN_CTMRA1C0INT_S; break; case AM_REG_CTIMER_INTEN_CTMRB1C0INT_M: intIdx = AM_REG_CTIMER_INTEN_CTMRB1C0INT_S; break; case AM_REG_CTIMER_INTEN_CTMRA2C0INT_M: intIdx = AM_REG_CTIMER_INTEN_CTMRA2C0INT_S; break; case AM_REG_CTIMER_INTEN_CTMRB2C0INT_M: intIdx = AM_REG_CTIMER_INTEN_CTMRB2C0INT_S; break; case AM_REG_CTIMER_INTEN_CTMRA3C0INT_M: intIdx = AM_REG_CTIMER_INTEN_CTMRA3C0INT_S; break; case AM_REG_CTIMER_INTEN_CTMRB3C0INT_M: intIdx = AM_REG_CTIMER_INTEN_CTMRB3C0INT_S; break; case AM_REG_CTIMER_INTEN_CTMRA0C1INT_M: intIdx = AM_REG_CTIMER_INTEN_CTMRA0C1INT_S; break; case AM_REG_CTIMER_INTEN_CTMRB0C1INT_M: intIdx = AM_REG_CTIMER_INTEN_CTMRB0C1INT_S; break; case AM_REG_CTIMER_INTEN_CTMRA1C1INT_M: intIdx = AM_REG_CTIMER_INTEN_CTMRA1C1INT_S; break; case AM_REG_CTIMER_INTEN_CTMRB1C1INT_M: intIdx = AM_REG_CTIMER_INTEN_CTMRB1C1INT_S; break; case AM_REG_CTIMER_INTEN_CTMRA2C1INT_M: intIdx = AM_REG_CTIMER_INTEN_CTMRA2C1INT_S; break; case AM_REG_CTIMER_INTEN_CTMRB2C1INT_M: intIdx = AM_REG_CTIMER_INTEN_CTMRB2C1INT_S; break; case AM_REG_CTIMER_INTEN_CTMRA3C1INT_M: intIdx = AM_REG_CTIMER_INTEN_CTMRA3C1INT_S; break; case AM_REG_CTIMER_INTEN_CTMRB3C1INT_M: intIdx = AM_REG_CTIMER_INTEN_CTMRB3C1INT_S; break; default: am_hal_debug_assert_msg(false, "CTimer interrupt number out of range."); } am_hal_ctimer_ppfnHandlers[intIdx] = pfnHandler; } // am_hal_ctimer_int_register() //***************************************************************************** // //! @brief Set up the counter/timer. //! //! @param ui32TimerNumber is the number of the Timer that should be //! configured. //! //! @param psConfig is a pointer to a structure that holds important settings //! for the timer. //! //! This function should be used to perform the initial set-up of the //! counter-timer. //! //! @note This function will eventually be replaced by //! am_hal_ctimer_config_single(), which performs the same configuration //! without requiring a structure. Please use am_hal_ctimer_config_single() for //! new development. //! //! @return None. // //***************************************************************************** void am_hal_ctimer_config(uint32_t ui32TimerNumber, am_hal_ctimer_config_t *psConfig) { uint32_t *pui32ConfigReg; uint32_t ui32ConfigVal; // // Start preparing the configuration word for this timer. The configuration // values for Timer A and Timer B provided in the config structure should // match the register definitions already, so we will mostly just need to // OR them together. // ui32ConfigVal = ( (psConfig->ui32TimerAConfig) | (psConfig->ui32TimerBConfig << 16) ); // // OR in the Link bit if the timers need to be linked. // ui32ConfigVal |= psConfig->ui32Link ? AM_HAL_CTIMER_LINK : 0; // // Begin critical section while config registers are read and modified. // AM_CRITICAL_BEGIN_ASM // // Find the correct register to write. // pui32ConfigReg = (uint32_t *)(AM_REG_CTIMERn(0) + AM_REG_CTIMER_CTRL0_O + (ui32TimerNumber * TIMER_OFFSET)); // // Write our configuration value. // AM_REGVAL(pui32ConfigReg) = ui32ConfigVal; // // If all of the clock sources are not HRFC disable LDO when sleeping if timers are enabled. // if ( timers_use_hfrc() ) { AM_BFW(PWRCTRL, MISCOPT, DIS_LDOLPMODE_TIMERS, 0); } else { AM_BFW(PWRCTRL, MISCOPT, DIS_LDOLPMODE_TIMERS, 1); } // // Done with critical section. // AM_CRITICAL_END_ASM } // am_hal_ctimer_config() //***************************************************************************** // //! @brief Set up the counter/timer. //! //! @param ui32TimerNumber is the number of the Timer that should be //! configured. //! //! @param ui32TimerSegment specifies which segment of the timer should be //! enabled. //! //! @param ui32ConfigVal specifies the configuration options for the selected //! timer. //! //! This function should be used to perform the initial set-up of the //! counter-timer. It can be used to configure either a 16-bit timer (A or B) or a //! 32-bit timer using the BOTH option. //! //! Valid values for ui32TimerSegment are: //! //! AM_HAL_CTIMER_TIMERA //! AM_HAL_CTIMER_TIMERB //! AM_HAL_CTIMER_BOTH //! //! The timer's clock source, mode, interrupt, and external pin behavior are //! all controlled through the \e ui32Configval parameter. The valid options //! for ui32ConfigVal include any ORed together combination of the following: //! //! Clock configuration macros: //! //! AM_HAL_CTIMER_HFRC_24MHZ //! AM_HAL_CTIMER_LFRC_512HZ //! ... etc. (See am_hal_ctimer.h for the full set of options.) //! //! Mode selection macros: //! //! AM_HAL_CTIMER_FN_ONCE //! AM_HAL_CTIMER_FN_REPEAT //! AM_HAL_CTIMER_FN_PWM_ONCE //! AM_HAL_CTIMER_FN_PWM_REPEAT //! AM_HAL_CTIMER_FN_CONTINUOUS //! //! Interrupt control: //! //! AM_HAL_CTIMER_INT_ENABLE //! //! Pin control: //! //! AM_HAL_CTIMER_PIN_ENABLE //! AM_HAL_CTIMER_PIN_INVERT //! //! ADC trigger (Timer 3 only): //! //! AM_HAL_CTIMER_ADC_TRIG //! //! @return None. // //***************************************************************************** void am_hal_ctimer_config_single(uint32_t ui32TimerNumber, uint32_t ui32TimerSegment, uint32_t ui32ConfigVal) { volatile uint32_t *pui32ConfigReg; uint32_t ui32WriteVal; // // Find the correct register to write based on the timer number. // pui32ConfigReg = (uint32_t *)(AM_REG_CTIMERn(0) + AM_REG_CTIMER_CTRL0_O + (ui32TimerNumber * TIMER_OFFSET)); // // Begin critical section while config registers are read and modified. // AM_CRITICAL_BEGIN_ASM // // Save the value that's already in the register. // ui32WriteVal = AM_REGVAL(pui32ConfigReg); // // If we're working with TIMERB, we need to shift our configuration value // up by 16 bits. // if ( ui32TimerSegment == AM_HAL_CTIMER_TIMERB ) { ui32ConfigVal = ((ui32ConfigVal & 0xFFFF) << 16); } // // Replace part of the saved register value with the configuration value // from the caller. // ui32WriteVal = (ui32WriteVal & ~(ui32TimerSegment)) | ui32ConfigVal; // // If we're configuring both timers, we need to set the "link" bit. // if ( ui32TimerSegment == AM_HAL_CTIMER_BOTH ) { ui32WriteVal |= AM_HAL_CTIMER_LINK; } // // Write our completed configuration value. // AM_REGVAL(pui32ConfigReg) = ui32WriteVal; // // If all of the clock sources are not HRFC disable LDO when sleeping if timers are enabled. // if ( timers_use_hfrc() ) { AM_BFW(PWRCTRL, MISCOPT, DIS_LDOLPMODE_TIMERS, 0); } else { AM_BFW(PWRCTRL, MISCOPT, DIS_LDOLPMODE_TIMERS, 1); } // // Done with critical section. // AM_CRITICAL_END_ASM } // am_hal_ctimer_config_single() //***************************************************************************** // //! @brief Start a timer //! //! @param ui32TimerNumber is the number of the timer to enable //! //! @param ui32TimerSegment specifies which segment of the timer should be //! enabled. Valid values for ui32TimerSegment are: //! AM_HAL_CTIMER_TIMERA //! AM_HAL_CTIMER_TIMERB //! AM_HAL_CTIMER_BOTH //! //! This function will enable a timer to begin incrementing. The \e //! ui32TimerNumber parameter selects the timer that should be enabled, for //! example, a 0 would target TIMER0. The \e ui32TimerSegment parameter allows //! the caller to individually select a segment within a timer to be enabled, //! such as TIMER0A, TIMER0B, or both. //! //! @return None. // //***************************************************************************** void am_hal_ctimer_start(uint32_t ui32TimerNumber, uint32_t ui32TimerSegment) { volatile uint32_t *pui32ConfigReg; uint32_t ui32ConfigVal; // // Find the correct control register. // pui32ConfigReg = (uint32_t *)(AM_REG_CTIMERn(0) + AM_REG_CTIMER_CTRL0_O + (ui32TimerNumber * TIMER_OFFSET)); // // Begin critical section while config registers are read and modified. // AM_CRITICAL_BEGIN_ASM // // Read the current value. // ui32ConfigVal = *pui32ConfigReg; // // Clear out the "clear" bit. // ui32ConfigVal &= ~(ui32TimerSegment & (AM_REG_CTIMER_CTRL0_TMRA0CLR_M | AM_REG_CTIMER_CTRL0_TMRB0CLR_M)); // // Set the "enable bit" // ui32ConfigVal |= (ui32TimerSegment & (AM_REG_CTIMER_CTRL0_TMRA0EN_M | AM_REG_CTIMER_CTRL0_TMRB0EN_M)); // // Write the value back to the register. // AM_REGVAL(pui32ConfigReg) = ui32ConfigVal; // // Done with critical section. // AM_CRITICAL_END_ASM } // am_hal_ctimer_start() //***************************************************************************** // //! @brief Stop a timer //! //! @param ui32TimerNumber is the number of the timer to disable. //! //! @param ui32TimerSegment specifies which segment of the timer should be //! disabled. //! //! This function will stop the selected timer from incrementing. The \e //! ui32TimerNumber parameter selects the timer that should be disabled, for //! example, a 0 would target TIMER0. The \e ui32TimerSegment parameter allows //! the caller to individually select a segment within a timer to be disabled, //! such as TIMER0A, TIMER0B, or both. //! //! This function will stop a counter/timer from counting, but does not return //! the count value to 'zero'. If you would like to reset the counter back to //! zero, try the am_hal_ctimer_clear() function instead. //! //! Valid values for ui32TimerSegment are: //! //! AM_HAL_CTIMER_TIMERA //! AM_HAL_CTIMER_TIMERB //! AM_HAL_CTIMER_BOTH //! //! @return None. // //***************************************************************************** void am_hal_ctimer_stop(uint32_t ui32TimerNumber, uint32_t ui32TimerSegment) { volatile uint32_t *pui32ConfigReg; // // Find the correct control register. // pui32ConfigReg = (uint32_t *)(AM_REG_CTIMERn(0) + AM_REG_CTIMER_CTRL0_O + (ui32TimerNumber * TIMER_OFFSET)); // // Begin critical section. // AM_CRITICAL_BEGIN_ASM // // Clear the "enable" bit // AM_REGVAL(pui32ConfigReg) &= ~(ui32TimerSegment & (AM_REG_CTIMER_CTRL0_TMRA0EN_M | AM_REG_CTIMER_CTRL0_TMRB0EN_M)); // // Done with critical section. // AM_CRITICAL_END_ASM } // am_hal_ctimer_stop() //***************************************************************************** // //! @brief Stops a timer and resets its value back to zero. //! //! @param ui32TimerNumber is the number of the timer to clear. //! //! @param ui32TimerSegment specifies which segment of the timer should be //! cleared. //! //! This function will stop a free-running counter-timer, reset its value to //! zero, and leave the timer disabled. When you would like to restart the //! counter, you will need to call am_hal_ctimer_start(). //! //! The \e ui32TimerSegment parameter allows the caller to individually select //! a segment within, such as TIMER0A, TIMER0B, or both. //! //! Valid values for ui32TimerSegment are: //! //! AM_HAL_CTIMER_TIMERA //! AM_HAL_CTIMER_TIMERB //! AM_HAL_CTIMER_BOTH //! //! @return None. // //***************************************************************************** void am_hal_ctimer_clear(uint32_t ui32TimerNumber, uint32_t ui32TimerSegment) { volatile uint32_t *pui32ConfigReg; // // Find the correct control register. // pui32ConfigReg = (uint32_t *)(AM_REG_CTIMERn(0) + AM_REG_CTIMER_CTRL0_O + (ui32TimerNumber * TIMER_OFFSET)); // // Begin critical section. // AM_CRITICAL_BEGIN_ASM // // Set the "clear" bit // AM_REGVAL(pui32ConfigReg) |= (ui32TimerSegment & (AM_REG_CTIMER_CTRL0_TMRA0CLR_M | AM_REG_CTIMER_CTRL0_TMRB0CLR_M)); // // Done with critical section. // AM_CRITICAL_END_ASM } // am_hal_ctimer_clear() //***************************************************************************** // //! @brief Returns the current free-running value of the selected timer. //! //! @param ui32TimerNumber is the number of the timer to read. //! @param ui32TimerSegment specifies which segment of the timer should be //! read. //! //! This function returns the current free-running value of the selected timer. //! //! @note When reading from a linked timer, be sure to use AM_HAL_CTIMER both //! for the segment argument. //! //! Valid values for ui32TimerSegment are: //! //! AM_HAL_CTIMER_TIMERA //! AM_HAL_CTIMER_TIMERB //! AM_HAL_CTIMER_BOTH //! //! @return Current timer value. // //***************************************************************************** uint32_t am_hal_ctimer_read(uint32_t ui32TimerNumber, uint32_t ui32TimerSegment) { volatile uint32_t ui32Value = 0; uint32_t ui32Values[4] = {0, }; uint32_t ui32TimerAddrTbl[4] = { REG_CTIMER_BASEADDR + AM_REG_CTIMER_TMR0_O, REG_CTIMER_BASEADDR + AM_REG_CTIMER_TMR1_O, REG_CTIMER_BASEADDR + AM_REG_CTIMER_TMR2_O, REG_CTIMER_BASEADDR + AM_REG_CTIMER_TMR3_O }; // // Read the timer with back2back reads. This is a workaround for a clock // domain synchronization issue. Some timer bits may be slow to increment, // which means that the value in the timer register will sometimes be // wrong. // // The architecture guarantees that: // // 1) If the timer is running at a speed close to the core frequency, the // core and timer clock domains will be synchronized, and no "bad" reads // will happen. // // 2) Bad reads will only happen if the core reads the timer register while // the timer value is transitioning from one count to the next. // // 3) The timer will resolve to the correct value within one 24 MHz clock // cycle. // // If we read the timer three times in a row with back-to-back load // instructions, then we can guarantee that the timer will only have time // to increment once, and that only one of the three reads can be wrong. // This routine will perform the back-to-back reads and return all three // values. The rest of this fuction determines which value we should // actually use. // back2back_reads(ui32TimerAddrTbl[ui32TimerNumber], ui32Values); // // Shift or mask the values based on the given timer segment. // if ( ui32TimerSegment == AM_HAL_CTIMER_TIMERB ) { ui32Values[0] >>= 16; ui32Values[1] >>= 16; ui32Values[2] >>= 16; } else if ( ui32TimerSegment == AM_HAL_CTIMER_TIMERA ) { ui32Values[0] &= 0xFFFF; ui32Values[1] &= 0xFFFF; ui32Values[2] &= 0xFFFF; } // // Now, we'll figure out which of the three values is the correct time. // if (ui32Values[0] == ui32Values[1]) { // // If the first two values match, then neither one was a bad read. // We'll take this as the current time. // ui32Value = ui32Values[1]; } else { // // If the first two values didn't match, then one of them might be bad. // If one of the first two values is bad, then the third one should // always be correct. We'll take the third value as the correct time. // ui32Value = ui32Values[2]; // // If all of the statements about the architecture are true, the third // value should be correct, and it should always be within one count of // either the first or the second value. // // Just in case, we'll check against the previous two values to make // sure that our final answer was reasonable. If it isn't, we will // flag it as a "bad read", and fail this assert statement. // // This shouldn't ever happen, and it hasn't ever happened in any of // our tests so far. // am_hal_debug_assert_msg((adjacent(ui32Values[1], ui32Values[2]) || adjacent(ui32Values[0], ui32Values[2])), "Bad CTIMER read"); } return ui32Value; } // am_hal_ctimer_read() //***************************************************************************** // //! @brief Enable output to the timer pin //! //! @param ui32TimerNumber is the number of the timer to configure. //! //! @param ui32TimerSegment specifies which segment of the timer to use. //! //! This function will enable the output pin for the selected timer. The \e //! ui32TimerSegment parameter allows the caller to individually select a //! segment within, such as TIMER0A, TIMER0B, or both. //! //! Valid values for ui32TimerSegment are: //! //! AM_HAL_CTIMER_TIMERA //! AM_HAL_CTIMER_TIMERB //! AM_HAL_CTIMER_BOTH //! //! @return None. // //***************************************************************************** void am_hal_ctimer_pin_enable(uint32_t ui32TimerNumber, uint32_t ui32TimerSegment) { volatile uint32_t *pui32ConfigReg; // // Find the correct control register. // pui32ConfigReg = (uint32_t *)(AM_REG_CTIMERn(0) + AM_REG_CTIMER_CTRL0_O + (ui32TimerNumber * TIMER_OFFSET)); // // Begin critical section. // AM_CRITICAL_BEGIN_ASM // // Set the pin enable bit // AM_REGVAL(pui32ConfigReg) |= (ui32TimerSegment & (AM_REG_CTIMER_CTRL0_TMRA0PE_M | AM_REG_CTIMER_CTRL0_TMRB0PE_M)); // // Done with critical section. // AM_CRITICAL_END_ASM } // am_hal_ctimer_pin_enable() //***************************************************************************** // //! @brief Disable the output pin. //! //! @param ui32TimerNumber is the number of the timer to configure. //! //! @param ui32TimerSegment specifies which segment of the timer to use. //! //! This function will disable the output pin for the selected timer. The \e //! ui32TimerSegment parameter allows the caller to individually select a //! segment within, such as TIMER0A, TIMER0B, or both. //! //! Valid values for ui32TimerSegment are: //! //! AM_HAL_CTIMER_TIMERA //! AM_HAL_CTIMER_TIMERB //! AM_HAL_CTIMER_BOTH //! //! @return None. // //***************************************************************************** void am_hal_ctimer_pin_disable(uint32_t ui32TimerNumber, uint32_t ui32TimerSegment) { volatile uint32_t *pui32ConfigReg; // // Find the correct control register. // pui32ConfigReg = (uint32_t *)(AM_REG_CTIMERn(0) + AM_REG_CTIMER_CTRL0_O + (ui32TimerNumber * TIMER_OFFSET)); // // Begin critical section. // AM_CRITICAL_BEGIN_ASM // // Clear the pin enable bit // AM_REGVAL(pui32ConfigReg) &= ~(ui32TimerSegment & (AM_REG_CTIMER_CTRL0_TMRA0PE_M | AM_REG_CTIMER_CTRL0_TMRB0PE_M)); // // Done with critical section. // AM_CRITICAL_END_ASM } // am_hal_ctimer_pin_disable() //***************************************************************************** // //! @brief Set the polarity of the output pin. //! //! @param ui32TimerNumber is the number of the timer to configure. //! //! @param ui32TimerSegment specifies which segment of the timer to use. //! //! @param bInvertOutput determines whether the output should be inverted. If //! true, the timer output pin for the selected timer segment will be //! inverted. //! //! This function will set the polarity of the the output pin for the selected //! timer. The \e ui32TimerSegment parameter allows the caller to individually //! select a segment within, such as TIMER0A, TIMER0B, or both. //! //! Valid values for ui32TimerSegment are: //! //! AM_HAL_CTIMER_TIMERA //! AM_HAL_CTIMER_TIMERB //! AM_HAL_CTIMER_BOTH //! //! @return None. // //***************************************************************************** void am_hal_ctimer_pin_invert(uint32_t ui32TimerNumber, uint32_t ui32TimerSegment, bool bInvertOutput) { volatile uint32_t *pui32ConfigReg; // // Find the correct control register. // pui32ConfigReg = (uint32_t *)(AM_REG_CTIMERn(0) + AM_REG_CTIMER_CTRL0_O + (ui32TimerNumber * TIMER_OFFSET)); // // Begin critical section. // AM_CRITICAL_BEGIN_ASM // // Figure out if we're supposed to be setting or clearing the polarity bit. // if ( bInvertOutput ) { // // Set the polarity bit to invert the output. // AM_REGVAL(pui32ConfigReg) |= (ui32TimerSegment & (AM_REG_CTIMER_CTRL0_TMRA0POL_M | AM_REG_CTIMER_CTRL0_TMRB0POL_M)); } else { // // Clear the polarity bit. // AM_REGVAL(pui32ConfigReg) &= ~(ui32TimerSegment & (AM_REG_CTIMER_CTRL0_TMRA0POL_M | AM_REG_CTIMER_CTRL0_TMRB0POL_M)); } // // Done with critical section. // AM_CRITICAL_END_ASM } // am_hal_ctimer_pin_invert() //***************************************************************************** // //! @brief Set a compare register. //! //! @param ui32TimerNumber is the number of the timer to configure. //! //! @param ui32TimerSegment specifies which segment of the timer to use. //! Valid values for ui32TimerSegment are: //! //! AM_HAL_CTIMER_TIMERA //! AM_HAL_CTIMER_TIMERB //! AM_HAL_CTIMER_BOTH //! //! @param ui32CompareReg specifies which compare register should be set //! (either 0 or 1) //! //! @param ui32Value is the value that should be written to the compare //! register. //! //! This function allows the caller to set the values in the compare registers //! for a timer. These registers control the period and duty cycle of the //! timers and their associated output pins. Please see the datasheet for //! further information on the operation of the compare registers. The \e //! ui32TimerSegment parameter allows the caller to individually select a //! segment within, such as TIMER0A, TIMER0B, or both. //! //! @note For simple manipulations of period or duty cycle for timers and PWMs, //! you may find it easier to use the am_hal_ctimer_period_set() function. //! //! @return None. // //***************************************************************************** void am_hal_ctimer_compare_set(uint32_t ui32TimerNumber, uint32_t ui32TimerSegment, uint32_t ui32CompareReg, uint32_t ui32Value) { volatile uint32_t *pui32CmprRegA, *pui32CmprRegB; uint32_t ui32CmprRegA, ui32CmprRegB; // // Find the correct compare register to write. // Assume A or BOTH. We'll change later if B. // pui32CmprRegA = (uint32_t *)(AM_REG_CTIMERn(0) + AM_REG_CTIMER_CMPRA0_O + (ui32TimerNumber * TIMER_OFFSET)); pui32CmprRegB = pui32CmprRegA + CTIMER_CMPR_OFFSET / 4; // // Write the compare register with the selected value. // Begin critical section while CMPR registers are modified. // AM_CRITICAL_BEGIN_ASM ui32CmprRegA = *pui32CmprRegA; ui32CmprRegB = *pui32CmprRegB; if ( ui32CompareReg == 1 ) { // // CMPR reg 1 // Get the lower 16b (but may not be used if TIMERB). // ui32CmprRegA = ( (ui32CmprRegA & AM_REG_CTIMER_CMPRA0_CMPR0A0_M) | AM_REG_CTIMER_CMPRA0_CMPR1A0(ui32Value & 0xFFFF) ); // // Get the upper 16b (but may not be used if TIMERA) // ui32CmprRegB = ( (ui32CmprRegB & AM_REG_CTIMER_CMPRA0_CMPR0A0_M) | AM_REG_CTIMER_CMPRA0_CMPR1A0(ui32Value >> 16) ); } else { // // CMPR reg 0 // Get the lower 16b (but may not be used if TIMERB) // ui32CmprRegA = ( (ui32CmprRegA & AM_REG_CTIMER_CMPRA0_CMPR1A0_M) | AM_REG_CTIMER_CMPRA0_CMPR0A0(ui32Value & 0xFFFF) ); // // Set the upper 16b (but may not be used if TIMERA) // ui32CmprRegB = ( (ui32CmprRegB & AM_REG_CTIMER_CMPRA0_CMPR1A0_M) | AM_REG_CTIMER_CMPRA0_CMPR0A0(ui32Value >> 16) ); } if ( ui32TimerSegment == AM_HAL_CTIMER_TIMERB ) { *pui32CmprRegB = ui32CmprRegB; } else { // // It's TIMERA or BOTH. // *pui32CmprRegA = ui32CmprRegA; if ( ui32TimerSegment == AM_HAL_CTIMER_BOTH ) { *pui32CmprRegB = ui32CmprRegB; } } // // Done with critical section. // AM_CRITICAL_END_ASM } // am_hal_ctimer_compare_set() //***************************************************************************** // //! @brief Set the period and duty cycle of a timer. //! //! @param ui32TimerNumber is the number of the timer to configure. //! //! @param ui32TimerSegment specifies which segment of the timer to use. //! //! @param ui32Period specifies the desired period. This parameter effectively //! specifies the CTIMER CMPR field(s). The CMPR fields are handled in hardware //! as (n+1) values, therefore ui32Period is actually specified as 1 less than //! the desired period. Finally, as mentioned in the data sheet, the CMPR fields //! cannot be 0 (a value of 1), so neither can ui32Period be 0. //! //! @param ui32OnTime set the number of clocks where the output signal is high. //! //! This function should be used for simple manipulations of the period and //! duty cycle of a counter/timer. To set the period and/or duty cycle of a //! linked timer pair, use AM_HAL_CTIMER_BOTH as the timer segment argument. If //! you would like to set the period and/or duty cycle for both TIMERA and //! TIMERB you will need to call this function twice: once for TIMERA, and once //! for TIMERB. //! //! Valid values for ui32TimerSegment are: //! //! AM_HAL_CTIMER_TIMERA //! AM_HAL_CTIMER_TIMERB //! AM_HAL_CTIMER_BOTH //! //! @note The ui32OnTime parameter will only work if the timer is currently //! operating in one of the PWM modes. //! //! @return None. // //***************************************************************************** void am_hal_ctimer_period_set(uint32_t ui32TimerNumber, uint32_t ui32TimerSegment, uint32_t ui32Period, uint32_t ui32OnTime) { volatile uint32_t *pui32ControlReg; volatile uint32_t *pui32CompareRegA; volatile uint32_t *pui32CompareRegB; uint32_t ui32Mode, ui32Comp0, ui32Comp1; // // Find the correct control register to pull the function select field // from. // pui32ControlReg = (uint32_t *)(AM_REG_CTIMERn(0) + AM_REG_CTIMER_CTRL0_O + (ui32TimerNumber * TIMER_OFFSET)); // // Find the correct compare registers to write. // pui32CompareRegA = (uint32_t *)(AM_REG_CTIMERn(0) + AM_REG_CTIMER_CMPRA0_O + (ui32TimerNumber * TIMER_OFFSET)); pui32CompareRegB = (uint32_t *)(AM_REG_CTIMERn(0) + AM_REG_CTIMER_CMPRB0_O + (ui32TimerNumber * TIMER_OFFSET)); // // Begin critical section. // AM_CRITICAL_BEGIN_ASM // // Extract the timer mode from the register based on the ui32TimerSegment // selected by the user. // ui32Mode = *pui32ControlReg; if ( ui32TimerSegment == AM_HAL_CTIMER_TIMERB ) { ui32Mode = ui32Mode >> 16; } // // Mask to get to the bits we're interested in. // ui32Mode = ui32Mode & AM_REG_CTIMER_CTRL0_TMRA0FN_M; // // If the mode is a PWM mode, we'll need to calculate the correct CMPR0 and // CMPR1 values here. // if (ui32Mode == AM_HAL_CTIMER_FN_PWM_ONCE || ui32Mode == AM_HAL_CTIMER_FN_PWM_REPEAT) { ui32Comp0 = ui32Period - ui32OnTime; ui32Comp1 = ui32Period; } else { ui32Comp0 = ui32Period; ui32Comp1 = 0; } // // Based on the timer segment argument, write the calculated Compare 0 and // Compare 1 values to the correct halves of the correct registers. // if ( ui32TimerSegment == AM_HAL_CTIMER_TIMERA ) { // // For timer A, write the values to the TIMERA compare register. // *pui32CompareRegA = (AM_REG_CTIMER_CMPRA0_CMPR0A0(ui32Comp0) | AM_REG_CTIMER_CMPRA0_CMPR1A0(ui32Comp1)); } else if ( ui32TimerSegment == AM_HAL_CTIMER_TIMERB ) { // // For timer B, write the values to the TIMERA compare register. // *pui32CompareRegB = (AM_REG_CTIMER_CMPRA0_CMPR0A0(ui32Comp0) | AM_REG_CTIMER_CMPRA0_CMPR1A0(ui32Comp1)); } else { // // For the linked case, write the lower halves of the values to the // TIMERA compare register, and the upper halves to the TIMERB compare // register. // *pui32CompareRegA = (AM_REG_CTIMER_CMPRA0_CMPR0A0(ui32Comp0) | AM_REG_CTIMER_CMPRA0_CMPR1A0(ui32Comp1)); *pui32CompareRegB = (AM_REG_CTIMER_CMPRA0_CMPR0A0(ui32Comp0 >> 16) | AM_REG_CTIMER_CMPRA0_CMPR1A0(ui32Comp1 >> 16)); } // // Done with critical section. // AM_CRITICAL_END_ASM } // am_hal_ctimer_period_set() //***************************************************************************** // //! @brief Enable the TIMERA3 ADC trigger //! //! This function enables the ADC trigger within TIMERA3. //! //! @return None. // //***************************************************************************** void am_hal_ctimer_adc_trigger_enable(void) { // // Begin critical section. // AM_CRITICAL_BEGIN_ASM // // Enable the ADC trigger. // AM_REGn(CTIMER, 0, CTRL3) |= AM_REG_CTIMER_CTRL3_ADCEN_M; // // Done with critical section. // AM_CRITICAL_END_ASM } // am_hal_ctimer_adc_trigger_enable() //***************************************************************************** // //! @brief Disable the TIMERA3 ADC trigger //! //! This function disables the ADC trigger within TIMERA3. //! //! @return None. // //***************************************************************************** void am_hal_ctimer_adc_trigger_disable(void) { // // Begin critical section. // AM_CRITICAL_BEGIN_ASM // // Disable the ADC trigger. // AM_REGn(CTIMER, 0, CTRL3) &= ~AM_REG_CTIMER_CTRL3_ADCEN_M; // // Done with critical section. // AM_CRITICAL_END_ASM } // am_hal_ctimer_adc_trigger_disable() //***************************************************************************** // //! @brief Enables the selected timer interrupt. //! //! @param ui32Interrupt is the interrupt to be used. //! //! This function will enable the selected interrupts in the main CTIMER //! interrupt enable register. In order to receive an interrupt from a timer, //! you will need to enable the interrupt for that timer in this main register, //! as well as in the timer control register (accessible though //! am_hal_ctimer_config()), and in the NVIC. //! //! ui32Interrupt should be the logical OR of one or more of the following //! values: //! //! AM_HAL_CTIMER_INT_TIMERA0C0 //! AM_HAL_CTIMER_INT_TIMERA0C1 //! AM_HAL_CTIMER_INT_TIMERB0C0 //! AM_HAL_CTIMER_INT_TIMERB0C1 //! AM_HAL_CTIMER_INT_TIMERA1C0 //! AM_HAL_CTIMER_INT_TIMERA1C1 //! AM_HAL_CTIMER_INT_TIMERB1C0 //! AM_HAL_CTIMER_INT_TIMERB1C1 //! AM_HAL_CTIMER_INT_TIMERA2C0 //! AM_HAL_CTIMER_INT_TIMERA2C1 //! AM_HAL_CTIMER_INT_TIMERB2C0 //! AM_HAL_CTIMER_INT_TIMERB2C1 //! AM_HAL_CTIMER_INT_TIMERA3C0 //! AM_HAL_CTIMER_INT_TIMERA3C1 //! AM_HAL_CTIMER_INT_TIMERB3C0 //! AM_HAL_CTIMER_INT_TIMERB3C1 //! //! @return None. // //***************************************************************************** void am_hal_ctimer_int_enable(uint32_t ui32Interrupt) { // // Begin critical section. // AM_CRITICAL_BEGIN_ASM // // Enable the interrupt at the module level. // AM_REGn(CTIMER, 0, INTEN) |= ui32Interrupt; // // Done with critical section. // AM_CRITICAL_END_ASM } // am_hal_ctimer_int_enable() //***************************************************************************** // //! @brief Return the enabled timer interrupts. //! //! This function will return all enabled interrupts in the main CTIMER //! interrupt enable register. //! //! @return return enabled interrupts. This will be a logical or of: //! //! AM_HAL_CTIMER_INT_TIMERA0C0 //! AM_HAL_CTIMER_INT_TIMERA0C1 //! AM_HAL_CTIMER_INT_TIMERB0C0 //! AM_HAL_CTIMER_INT_TIMERB0C1 //! AM_HAL_CTIMER_INT_TIMERA1C0 //! AM_HAL_CTIMER_INT_TIMERA1C1 //! AM_HAL_CTIMER_INT_TIMERB1C0 //! AM_HAL_CTIMER_INT_TIMERB1C1 //! AM_HAL_CTIMER_INT_TIMERA2C0 //! AM_HAL_CTIMER_INT_TIMERA2C1 //! AM_HAL_CTIMER_INT_TIMERB2C0 //! AM_HAL_CTIMER_INT_TIMERB2C1 //! AM_HAL_CTIMER_INT_TIMERA3C0 //! AM_HAL_CTIMER_INT_TIMERA3C1 //! AM_HAL_CTIMER_INT_TIMERB3C0 //! AM_HAL_CTIMER_INT_TIMERB3C1 //! //! @return Return the enabled timer interrupts. // //***************************************************************************** uint32_t am_hal_ctimer_int_enable_get(void) { // // Return enabled interrupts. // return AM_REGn(CTIMER, 0, INTEN); } // am_hal_ctimer_int_enable_get() //***************************************************************************** // //! @brief Disables the selected timer interrupt. //! //! @param ui32Interrupt is the interrupt to be used. //! //! This function will disable the selected interrupts in the main CTIMER //! interrupt register. //! //! ui32Interrupt should be the logical OR of one or more of the following //! values: //! //! AM_HAL_CTIMER_INT_TIMERA0C0 //! AM_HAL_CTIMER_INT_TIMERA0C1 //! AM_HAL_CTIMER_INT_TIMERB0C0 //! AM_HAL_CTIMER_INT_TIMERB0C1 //! AM_HAL_CTIMER_INT_TIMERA1C0 //! AM_HAL_CTIMER_INT_TIMERA1C1 //! AM_HAL_CTIMER_INT_TIMERB1C0 //! AM_HAL_CTIMER_INT_TIMERB1C1 //! AM_HAL_CTIMER_INT_TIMERA2C0 //! AM_HAL_CTIMER_INT_TIMERA2C1 //! AM_HAL_CTIMER_INT_TIMERB2C0 //! AM_HAL_CTIMER_INT_TIMERB2C1 //! AM_HAL_CTIMER_INT_TIMERA3C0 //! AM_HAL_CTIMER_INT_TIMERA3C1 //! AM_HAL_CTIMER_INT_TIMERB3C0 //! AM_HAL_CTIMER_INT_TIMERB3C1 //! //! @return None. // //***************************************************************************** void am_hal_ctimer_int_disable(uint32_t ui32Interrupt) { // // Begin critical section. // AM_CRITICAL_BEGIN_ASM // // Disable the interrupt at the module level. // AM_REGn(CTIMER, 0, INTEN) &= ~ui32Interrupt; // // Done with critical section. // AM_CRITICAL_END_ASM } // am_hal_ctimer_int_disable() //***************************************************************************** // //! @brief Clears the selected timer interrupt. //! //! @param ui32Interrupt is the interrupt to be used. //! //! This function will clear the selected interrupts in the main CTIMER //! interrupt register. //! //! ui32Interrupt should be the logical OR of one or more of the following //! values: //! //! AM_HAL_CTIMER_INT_TIMERA0C0 //! AM_HAL_CTIMER_INT_TIMERA0C1 //! AM_HAL_CTIMER_INT_TIMERB0C0 //! AM_HAL_CTIMER_INT_TIMERB0C1 //! AM_HAL_CTIMER_INT_TIMERA1C0 //! AM_HAL_CTIMER_INT_TIMERA1C1 //! AM_HAL_CTIMER_INT_TIMERB1C0 //! AM_HAL_CTIMER_INT_TIMERB1C1 //! AM_HAL_CTIMER_INT_TIMERA2C0 //! AM_HAL_CTIMER_INT_TIMERA2C1 //! AM_HAL_CTIMER_INT_TIMERB2C0 //! AM_HAL_CTIMER_INT_TIMERB2C1 //! AM_HAL_CTIMER_INT_TIMERA3C0 //! AM_HAL_CTIMER_INT_TIMERA3C1 //! AM_HAL_CTIMER_INT_TIMERB3C0 //! AM_HAL_CTIMER_INT_TIMERB3C1 //! //! @return None. // //***************************************************************************** void am_hal_ctimer_int_clear(uint32_t ui32Interrupt) { // // Disable the interrupt at the module level. // AM_REGn(CTIMER, 0, INTCLR) = ui32Interrupt; } // am_hal_ctimer_int_clear() //***************************************************************************** // //! @brief Sets the selected timer interrupt. //! //! @param ui32Interrupt is the interrupt to be used. //! //! This function will set the selected interrupts in the main CTIMER //! interrupt register. //! //! ui32Interrupt should be the logical OR of one or more of the following //! values: //! //! AM_HAL_CTIMER_INT_TIMERA0C0 //! AM_HAL_CTIMER_INT_TIMERA0C1 //! AM_HAL_CTIMER_INT_TIMERB0C0 //! AM_HAL_CTIMER_INT_TIMERB0C1 //! AM_HAL_CTIMER_INT_TIMERA1C0 //! AM_HAL_CTIMER_INT_TIMERA1C1 //! AM_HAL_CTIMER_INT_TIMERB1C0 //! AM_HAL_CTIMER_INT_TIMERB1C1 //! AM_HAL_CTIMER_INT_TIMERA2C0 //! AM_HAL_CTIMER_INT_TIMERA2C1 //! AM_HAL_CTIMER_INT_TIMERB2C0 //! AM_HAL_CTIMER_INT_TIMERB2C1 //! AM_HAL_CTIMER_INT_TIMERA3C0 //! AM_HAL_CTIMER_INT_TIMERA3C1 //! AM_HAL_CTIMER_INT_TIMERB3C0 //! AM_HAL_CTIMER_INT_TIMERB3C1 //! //! @return None. // //***************************************************************************** void am_hal_ctimer_int_set(uint32_t ui32Interrupt) { // // Set the interrupts. // AM_REGn(CTIMER, 0, INTSET) = ui32Interrupt; } // am_hal_ctimer_int_set() //***************************************************************************** // //! @brief Returns either the enabled or raw timer interrupt status. //! //! This function will return the timer interrupt status. //! //! @return bEnabledOnly if true returns the status of the enabled interrupts //! only. //! //! The return value will be the logical OR of one or more of the following //! values: //! //! AM_HAL_CTIMER_INT_TIMERA0C0 //! AM_HAL_CTIMER_INT_TIMERA0C1 //! AM_HAL_CTIMER_INT_TIMERB0C0 //! AM_HAL_CTIMER_INT_TIMERB0C1 //! AM_HAL_CTIMER_INT_TIMERA1C0 //! AM_HAL_CTIMER_INT_TIMERA1C1 //! AM_HAL_CTIMER_INT_TIMERB1C0 //! AM_HAL_CTIMER_INT_TIMERB1C1 //! AM_HAL_CTIMER_INT_TIMERA2C0 //! AM_HAL_CTIMER_INT_TIMERA2C1 //! AM_HAL_CTIMER_INT_TIMERB2C0 //! AM_HAL_CTIMER_INT_TIMERB2C1 //! AM_HAL_CTIMER_INT_TIMERA3C0 //! AM_HAL_CTIMER_INT_TIMERA3C1 //! AM_HAL_CTIMER_INT_TIMERB3C0 //! AM_HAL_CTIMER_INT_TIMERB3C1 //! //! @return Returns either the timer interrupt status. // //***************************************************************************** uint32_t am_hal_ctimer_int_status_get(bool bEnabledOnly) { // // Return the desired status. // if ( bEnabledOnly ) { uint32_t u32RetVal; // // Begin critical section. // AM_CRITICAL_BEGIN_ASM u32RetVal = AM_REGn(CTIMER, 0, INTSTAT); u32RetVal &= AM_REGn(CTIMER, 0, INTEN); // // Done with critical section. // AM_CRITICAL_END_ASM return u32RetVal; } else { return AM_REGn(CTIMER, 0, INTSTAT); } } // am_hal_ctimer_int_status_get() //***************************************************************************** // // End Doxygen group. //! @} // //*****************************************************************************