menu "Hardware Drivers Config"

config SOC_STM32H743II
    bool
    select SOC_SERIES_STM32H7
    select RT_USING_COMPONENTS_INIT
    select RT_USING_USER_MAIN
    default y

menu "Onboard Peripheral Drivers"

    config BSP_USING_COM2
        bool "Enable COM2(485)"
        select BSP_USING_UART
        select BSP_USING_UART2
        select BSP_USING_I2C1
        select PKG_USING_PCF8574
        default n

    config BSP_USING_SDRAM
        bool "Enable SDRAM"
        select BSP_USING_FMC
        default n

    config BSP_USING_LCD
        bool "Enable LCD"
        select BSP_USING_LTDC
        select BSP_USING_SDRAM
        default n

    config BSP_USING_QSPI_FLASH
        bool "Enable QSPI FLASH (W25Q256 qspi)"
        select BSP_USING_QSPI
        select RT_USING_SFUD
        select RT_SFUD_USING_QSPI
        default n
    config BSP_USING_SDMMC
        bool "Enable SDMMC (SD card)"
        select RT_USING_SDIO
        select RT_USING_DFS
        select RT_USING_DFS_ELMFAT
        default n

    config BSP_USING_OV2640
        bool "Enable camera (ov2640)"
        select BSP_USING_DCMI
        select BSP_USING_I2C
        select BSP_USING_I2C2
        default n

endmenu

menu "On-chip Peripheral Drivers"

    config BSP_USING_GPIO
        bool "Enable GPIO"
        select RT_USING_PIN
        default y

    menuconfig BSP_USING_UART
        bool "Enable UART"
        default y
        select RT_USING_SERIAL
        if BSP_USING_UART
            config BSP_USING_UART1
                bool "Enable UART1"
                default y

            config BSP_USING_UART2
                bool "Enable UART2"
                default n

            config BSP_UART2_RX_USING_DMA
                bool "Enable UART2 RX DMA"
                depends on BSP_USING_UART2 && RT_SERIAL_USING_DMA
                default n

            config BSP_UART2_TX_USING_DMA
                bool "Enable UART2 TX DMA"
                depends on BSP_USING_UART2 && RT_SERIAL_USING_DMA
                default n
        endif

    config BSP_USING_FMC
        bool
        default n

    config BSP_USING_LTDC
        bool
        default n

    menuconfig BSP_USING_SPI
        bool "Enable SPI BUS"
        default n
        select RT_USING_SPI
        if BSP_USING_SPI
            config BSP_USING_SPI2
                bool "Enable SPI2 BUS"
                default n
        endif

    config BSP_USING_QSPI
        bool "Enable QSPI BUS"
        select RT_USING_QSPI
        select RT_USING_SPI
        default n

    menuconfig BSP_USING_I2C
    bool "Enable I2C BUS (software simulation)"
    select RT_USING_I2C
    select RT_USING_I2C_BITOPS
    select RT_USING_PIN
    default n
    if BSP_USING_I2C
        menuconfig BSP_USING_I2C1
            bool "Enable I2C1 BUS (software simulation)"
            default n
            if BSP_USING_I2C1
                comment "Notice: PH4 --> 116; PH5 --> 117"
                config BSP_I2C1_SCL_PIN
                    int "i2c1 scl pin number"
                    range 1 176
                    default 116
                config BSP_I2C1_SDA_PIN
                    int "I2C1 sda pin number"
                    range 1 176
                    default 117
                        menuconfig BSP_USING_I2C2
                    bool "Enable I2C2 BUS (software simulation)"
                    default n
            endif

            menuconfig BSP_USING_I2C2
            bool "Enable I2C2 BUS (software simulation)"
            default n
            if BSP_USING_I2C2
                comment "Notice: PH13 --> 125; PH15 --> 127"
                config BSP_I2C2_SCL_PIN
                    int "i2c2 scl pin number"
                    range 1 176
                    default 127
                config BSP_I2C2_SDA_PIN
                    int "I2C2 sda pin number"
                    range 1 176
                    default 125
            endif
    endif

    config BSP_USING_ON_CHIP_FLASH
        bool "Enable on-chip FLASH"
        default n

    config BSP_USING_DCMI
        bool "Enable DCMI"
        default n

    menuconfig BSP_USING_ONCHIP_RTC
        bool "Enable RTC"
        select RT_USING_RTC
        default n
        if BSP_USING_ONCHIP_RTC
            choice
                prompt "Select clock source"
                default BSP_RTC_USING_LSE

                config BSP_RTC_USING_LSE
                    bool "RTC USING LSE"

                config BSP_RTC_USING_LSI
                    bool "RTC USING LSI"
            endchoice
        endif

    menuconfig BSP_USING_ADC
        bool "Enable ADC"
        default n
        select RT_USING_ADC
        if BSP_USING_ADC
            config BSP_USING_ADC1
                bool "Enable ADC1"
                default n
        endif

    menuconfig BSP_USING_DAC
        bool "Enable DAC"
        default n
        select RT_USING_DAC
        if BSP_USING_DAC
            config BSP_USING_DAC1
                bool "Enable DAC1"
                default n
        endif

    config BSP_USING_WDT
        bool "Enable Watchdog Timer"
        select RT_USING_WDT
        default n


    source "$BSP_DIR/../libraries/HAL_Drivers/drivers/Kconfig"

endmenu

menu "Board extended module Drivers"

endmenu

endmenu