menu "Hardware Drivers Config" menu "Onboard Peripheral Drivers" config BSP_USING_STLINK_TO_USART bool "Enable STLINK TO USART (uart1)" select BSP_USING_UART select BSP_USING_UART1 default y config BSP_USING_ARDUINO bool "Compatible with Arduino Ecosystem (RTduino)" select PKG_USING_RTDUINO select BSP_USING_STLINK_TO_USART select BSP_USING_GPIO select BSP_USING_TIM select BSP_USING_TIM7 select BSP_USING_PWM select BSP_USING_PWM1 select BSP_USING_PWM1_CH1 select BSP_USING_PWM2 select BSP_USING_PWM2_CH3 select BSP_USING_PWM2_CH4 select BSP_USING_PWM4 select BSP_USING_PWM4_CH1 select BSP_USING_PWM4_CH3 select BSP_USING_PWM4_CH4 select BSP_USING_ADC select BSP_USING_ADC1 select BSP_USING_I2C select BSP_USING_I2C1 # PC7-SDA PC6-SCL (User I2C) select BSP_USING_DAC select BSP_USING_DAC1 select BSP_USING_SPI select BSP_USING_SPI2 # Wireless Interface (User SPI) select BSP_SPI2_TX_USING_DMA select BSP_SPI2_RX_USING_DMA select RTDUINO_USING_WIRE select RTDUINO_USING_SPI imply RTDUINO_USING_SERVO default n if BSP_USING_ARDUINO config BSP_USING_ARDUINO_ST7789 bool "Enable Arduino LCD (ST7789) library" select BSP_USING_SPI3 select BSP_SPI3_TX_USING_DMA select BSP_USING_PWM4_CH2 select PKG_USING_ARDUINO_ADAFRUIT_ST7735 depends on !BSP_USING_SPI_LCD default n config BSP_USING_ARDUINO_ST7789_DEMO bool "Enable Arduino LCD (ST7789) library demo" depends on BSP_USING_ARDUINO_ST7789 default n config BSP_USING_ARDUINO_AHT10 bool "Enable Arduino AHT10 sensor library" select BSP_USING_I2C4 select PKG_USING_ARDUINO_ADAFRUIT_AHTX0 depends on !BSP_USING_AHT10 default n config BSP_USING_ARDUINO_AHT10_DEMO bool "Enable Arduino AHT10 sensor library demo" select PKG_USING_ARDUINO_MSGQ_C_CPP_DEMO depends on BSP_USING_ARDUINO_AHT10 default n config BSP_USING_ARDUINO_AP3216 bool select BSP_USING_I2C3 depends on !BSP_USING_AP3216C default n config BSP_USING_ARDUINO_ICM20608 bool select BSP_USING_I2C3 depends on !BSP_USING_ICM20608 default n endif config BSP_USING_KEY bool "Enable onboard keys" select RT_USING_PIN select RT_USING_TIMER_SOFT select PKG_USING_MULTIBUTTON default n config BSP_USING_QSPI_FLASH bool "Enable QSPI FLASH (W25Q128 qspi1)" select BSP_USING_QSPI select RT_USING_SFUD select RT_SFUD_USING_QSPI default n config BSP_USING_SPI_LCD bool "Enable LCD (spi3)" select BSP_USING_SPI select BSP_USING_SPI3 select BSP_SPI3_TX_USING_DMA select BSP_USING_PWM select BSP_USING_PWM4 select BSP_USING_PWM4_CH2 default n config BSP_USING_LCD_SAMPLE bool "Enable LCD raw driver sample" depends on BSP_USING_SPI_LCD && !BSP_USING_LVGL default n config BSP_USING_LCD_QRCODE bool "Enable LCD to show QRCode" depends on BSP_USING_SPI_LCD && !BSP_USING_LVGL select BSP_USING_LCD_SAMPLE select PKG_USING_QRCODE default n config BSP_USING_LVGL bool "Enable LVGL for LCD" select PKG_USING_LVGL select BSP_USING_SPI_LCD default n if BSP_USING_LVGL config BSP_USING_LVGL_DEMO bool "Enable LVGL demo" default y endif menuconfig BSP_USING_FS bool "Enable File System" select RT_USING_DFS select RT_USING_DFS_ROMFS default n if BSP_USING_FS config BSP_USING_SDCARD_FATFS bool "Enable SDCARD (FATFS)" select BSP_USING_SPI select BSP_USING_SPI1 select RT_USING_SPI_MSD select RT_USING_DFS_ELMFAT default n config BSP_USING_SPI_FLASH_LITTLEFS bool "Enable SPI-FLASH (LittleFS)" select RT_USING_MTD_NOR select BSP_USING_QSPI_FLASH select RT_USING_FAL select FAL_USING_AUTO_INIT select FAL_PART_HAS_TABLE_CFG select PKG_USING_LITTLEFS default n endif config BSP_USING_ICM20608 bool "Enable ICM20608 (i2c3)" select BSP_USING_I2C select BSP_USING_I2C3 select PKG_USING_MPU6XXX select PKG_USING_MPU6XXX_LATEST_VERSION default n config BSP_USING_AHT10 bool "Enable AHT10 (i2c4)" select BSP_USING_I2C select BSP_USING_I2C4 select PKG_USING_AHT10 select AHT10_USING_SENSOR_DEVICE default n config BSP_USING_AP3216C bool "Enable AP3216C (i2c3)" select BSP_USING_I2C select BSP_USING_I2C3 select PKG_USING_AP3216C select AP3216C_USING_SENSOR_DEVICE default n menuconfig BSP_USING_AUDIO bool "Enable Audio Device" select RT_USING_AUDIO select BSP_USING_I2C select BSP_USING_I2C3 default n if BSP_USING_AUDIO config BSP_USING_AUDIO_PLAY bool "Enable Audio Play" default y config BSP_USING_AUDIO_RECORD bool "Enable Audio Record" default n endif menuconfig BSP_USING_USB_AUDIO bool "Enable USB Audio" select RT_USB_DEVICE_AUDIO select BSP_USING_USBD select BSP_USBD_EP_ISOC select BSP_USING_AUDIO default n if BSP_USING_USB_AUDIO config BSP_USING_USB_AUDIO_SPEAKER bool "Enable USB Audio Spearker" select RT_USB_DEVICE_AUDIO_SPEAKER select BSP_USING_AUDIO_PLAY default y config BSP_USING_USB_AUDIO_MIC bool "Enable USB Audio Mic" select RT_USB_DEVICE_AUDIO_MIC select BSP_USING_AUDIO_RECORD default n config _BSP_USB_DEVICE_COMPOSITE bool select RT_USB_DEVICE_COMPOSITE default y depends on BSP_USING_USB_AUDIO_SPEAKER && BSP_USING_USB_AUDIO_MIC endif config BSP_USING_WIFI bool "Enable WiFi (AP6181)" select PKG_USING_WLAN_WICED select BSP_USING_STM32_SDIO select PKG_USING_STM32_SDIO select BSP_USING_QSPI_FLASH select BSP_USING_ON_CHIP_FLASH select RT_USING_WIFI select RT_WLAN_PROT_LWIP_PBUF_FORCE select RT_USING_LWIP select RT_USING_DFS select DFS_USING_POSIX select RT_USING_FAL select PKG_USING_EASYFLASH select RT_USING_WIFI_6181_LIB select RT_USING_OTA_LIB select RT_USING_SAL default n if BSP_USING_WIFI config BSP_USING_WIFI_THREAD_INIT bool "Using Thread Initialize WiFi" default n config BSP_USING_WIFI_AUTO_INIT bool "Using WiFi Automatically Initialization" depends on RT_USING_COMPONENTS_INIT default y endif endmenu menu "On-chip Peripheral Drivers" config BSP_USING_GPIO bool "Enable GPIO" select RT_USING_PIN default y menuconfig BSP_USING_UART bool "Enable UART" default y select RT_USING_SERIAL if BSP_USING_UART menuconfig BSP_USING_UART1 bool "Enable UART1 (Debugger)" default y if BSP_USING_UART1 config BSP_UART1_RX_USING_DMA bool "Enable UART1 RX DMA" depends on BSP_USING_UART1 && RT_SERIAL_USING_DMA default n config BSP_UART1_TX_USING_DMA bool "Enable UART1 TX DMA" depends on BSP_USING_UART1 && RT_SERIAL_USING_DMA default n config BSP_UART1_RX_BUFSIZE int "Set UART1 RX buffer size" range 64 65535 depends on RT_USING_SERIAL_V2 default 256 config BSP_UART1_TX_BUFSIZE int "Set UART1 TX buffer size" range 0 65535 depends on RT_USING_SERIAL_V2 default 0 endif menuconfig BSP_USING_UART2 bool "Enable UART2" default n if BSP_USING_UART2 config BSP_UART2_RX_USING_DMA bool "Enable UART2 RX DMA" depends on BSP_USING_UART2 && RT_SERIAL_USING_DMA default n config BSP_UART2_TX_USING_DMA bool "Enable UART2 TX DMA" depends on BSP_USING_UART2 && RT_SERIAL_USING_DMA default n config BSP_UART2_RX_BUFSIZE int "Set UART2 RX buffer size" range 64 65535 depends on RT_USING_SERIAL_V2 default 256 config BSP_UART2_TX_BUFSIZE int "Set UART2 TX buffer size" range 0 65535 depends on RT_USING_SERIAL_V2 default 256 endif endif config BSP_USING_ON_CHIP_FLASH bool "Enable on-chip FLASH" default n menuconfig BSP_USING_SPI bool "Enable SPI Bus" default n select RT_USING_SPI if BSP_USING_SPI config BSP_USING_SPI1 bool "Enable SPI1 Bus" default n config BSP_SPI1_TX_USING_DMA bool "Enable SPI1 TX DMA" depends on BSP_USING_SPI1 default n config BSP_SPI1_RX_USING_DMA bool "Enable SPI1 RX DMA" depends on BSP_USING_SPI1 select BSP_SPI1_TX_USING_DMA default n config BSP_USING_SPI2 bool "Enable SPI2 Bus" default n config BSP_SPI2_TX_USING_DMA bool "Enable SPI2 TX DMA" depends on BSP_USING_SPI2 default n config BSP_SPI2_RX_USING_DMA bool "Enable SPI2 RX DMA" depends on BSP_USING_SPI2 select BSP_SPI2_TX_USING_DMA default n config BSP_USING_SPI3 bool "Enable SPI3 Bus" default n config BSP_SPI3_TX_USING_DMA bool "Enable SPI3 TX DMA" depends on BSP_USING_SPI3 default n config BSP_SPI3_RX_USING_DMA bool "Enable SPI3 RX DMA" depends on BSP_USING_SPI3 select BSP_SPI3_TX_USING_DMA default n endif config BSP_USING_QSPI bool "Enable QSPI Bus" select RT_USING_QSPI select RT_USING_SPI default n config BSP_QSPI_USING_DMA bool "Enable QSPI DMA support" default n menuconfig BSP_USING_I2C bool "Enable I2C Bus" default n select RT_USING_I2C select RT_USING_I2C_BITOPS select RT_USING_PIN if BSP_USING_I2C config BSP_USING_I2C1 bool "Enable I2C1 Bus (User I2C)" default n if BSP_USING_I2C1 comment "Notice: PC7 --> 39; PC6 --> 38" config BSP_I2C1_SCL_PIN int "i2c1 SCL pin number" range 1 176 default 38 config BSP_I2C1_SDA_PIN int "i2c1 SDA pin number" range 1 176 default 39 endif config BSP_USING_I2C3 bool "Enable I2C3 Bus (AP3216C/ICM20608/ES8388)" default n if BSP_USING_I2C3 # Notice: PC0 --> 32; PC1 --> 33 config BSP_I2C3_SCL_PIN int default 32 config BSP_I2C3_SDA_PIN int default 33 endif config BSP_USING_I2C4 bool "Enable I2C4 Bus (AHT10)" default n if BSP_USING_I2C4 # Notice: PC1 --> 33; PD6 --> 54 config BSP_I2C4_SCL_PIN int default 54 config BSP_I2C4_SDA_PIN int default 33 endif endif menuconfig BSP_USING_TIM bool "Enable timer" default n select RT_USING_HWTIMER if BSP_USING_TIM config BSP_USING_TIM7 bool "Enable TIM7" default n config BSP_USING_TIM15 bool "Enable TIM15" default n config BSP_USING_TIM16 bool "Enable TIM16" default n config BSP_USING_TIM17 bool "Enable TIM17" default n endif menuconfig BSP_USING_PWM bool "Enable PWM" default n select RT_USING_PWM if BSP_USING_PWM menuconfig BSP_USING_PWM1 bool "Enable timer1 output PWM" default n if BSP_USING_PWM1 config BSP_USING_PWM1_CH1 bool "Enable PWM1 channel1" default n endif menuconfig BSP_USING_PWM2 bool "Enable timer2 output PWM" default n if BSP_USING_PWM2 config BSP_USING_PWM2_CH3 bool "Enable PWM2 channel3" default n config BSP_USING_PWM2_CH4 bool "Enable PWM2 channel4" default n endif menuconfig BSP_USING_PWM4 bool "Enable timer4 output PWM" default n if BSP_USING_PWM4 config BSP_USING_PWM4_CH1 bool "Enable PWM4 channel1" default n config BSP_USING_PWM4_CH2 bool "Enable PWM4 channel2" default n config BSP_USING_PWM4_CH3 bool "Enable PWM4 channel3" default n config BSP_USING_PWM4_CH4 bool "Enable PWM4 channel4" default n endif endif menuconfig BSP_USING_ADC bool "Enable ADC" default n select RT_USING_ADC if BSP_USING_ADC config BSP_USING_ADC1 bool "Enable ADC1" default n endif menuconfig BSP_USING_DAC bool "Enable DAC" default n select RT_USING_DAC if BSP_USING_DAC config BSP_USING_DAC1 bool "Enable DAC1" default n endif menuconfig BSP_USING_ONCHIP_RTC bool "Enable RTC" select RT_USING_RTC default n if BSP_USING_ONCHIP_RTC choice prompt "Select clock source" default BSP_RTC_USING_LSE config BSP_RTC_USING_LSE bool "RTC USING LSE" config BSP_RTC_USING_LSI bool "RTC USING LSI" endchoice endif config BSP_USING_WDT bool "Enable Watchdog Timer" select RT_USING_WDT default n config BSP_USING_USBD bool "Enable OTGFS as USB device" select RT_USING_USB_DEVICE default n config BSP_USBD_EP_ISOC bool default n depends on BSP_USING_USBD config BSP_USING_STM32_SDIO bool "Enable SDIO" select RT_USING_SDIO select PKG_USING_STM32_SDIO default n help BSP_USING_STM32_SDIO use drv_sdio_adapter.c,and BSP_USING_SDIO use drv_sdio.c source "$(BSP_DIR)/../libraries/HAL_Drivers/drivers/Kconfig" endmenu menu "Board extended module Drivers" menuconfig BSP_USING_AT_ESP8266 bool "Enable ESP8266(AT Command, COM2)" default n select BSP_USING_COM2 select PKG_USING_AT_DEVICE select AT_DEVICE_USING_ESP8266 select AT_DEVICE_ESP8266_SAMPLE select AT_DEVICE_ESP8266_SAMPLE_BSP_TAKEOVER if BSP_USING_AT_ESP8266 config ESP8266_SAMPLE_WIFI_SSID string "WIFI ssid" default "rtthread" config ESP8266_SAMPLE_WIFI_PASSWORD string "WIFI password" default "12345678" config ESP8266_SAMPLE_CLIENT_NAME string "AT client device name (Must be 'uart2')" default "uart2" config ESP8266_SAMPLE_RECV_BUFF_LEN int "The maximum length of receive line buffer" default 512 comment "May adjust RT_SERIAL_RB_BUFSZ up to 512 if using the Serial V1 device driver" endif config BSP_USING_NRF24L01 bool "Enable NRF24L01" select BSP_USING_SPI select BSP_USING_SPI2 select PKG_USING_NRF24L01 default n endmenu endmenu