menu "Hardware Drivers Config"

config SOC_HC32F460PE
    bool
    select SOC_SERIES_HC32F4
    select RT_USING_COMPONENTS_INIT
    select RT_USING_USER_MAIN
    default y

menu "Onboard Peripheral Drivers"

endmenu

menu "On-chip Peripheral Drivers"
    config BSP_USING_GPIO
        bool "Enable GPIO"
        select RT_USING_PIN
        default y

    menuconfig BSP_USING_UART
        bool "Enable UART"
        default y
        select RT_USING_SERIAL
        if BSP_USING_UART
            config BSP_USING_UART1
                bool "Enable UART1"
                default y

            config BSP_UART1_RX_USING_DMA
                bool "Enable UART1 RX DMA"
                depends on BSP_USING_UART1
                select RT_SERIAL_USING_DMA
                default n

            config BSP_UART1_TX_USING_DMA
                bool "Enable UART1 TX DMA"
                depends on BSP_USING_UART1
                select RT_SERIAL_USING_DMA
                default n

            config BSP_USING_UART2
                bool "Enable UART2"
                default n

            config BSP_UART2_RX_USING_DMA
                bool "Enable UART2 RX DMA"
                depends on BSP_USING_UART2
                select RT_SERIAL_USING_DMA
                default n

            config BSP_UART2_TX_USING_DMA
                bool "Enable UART2 TX DMA"
                depends on BSP_USING_UART2
                select RT_SERIAL_USING_DMA
                default n

            config BSP_USING_UART3
                bool "Enable UART3"
                default n

            config BSP_UART3_RX_USING_DMA
                bool "Enable UART3 RX DMA"
                depends on BSP_USING_UART3
                select RT_SERIAL_USING_DMA
                default n

            config BSP_UART3_TX_USING_DMA
                bool "Enable UART3 TX DMA"
                depends on BSP_USING_UART3
                select RT_SERIAL_USING_DMA
                default n

            config BSP_USING_UART4
                bool "Enable UART4"
                default n

            config BSP_UART4_RX_USING_DMA
                bool "Enable UART4 RX DMA"
                depends on BSP_USING_UART4
                select RT_SERIAL_USING_DMA
                default n

            config BSP_UART4_TX_USING_DMA
                bool "Enable UART4 TX DMA"
                depends on BSP_USING_UART4
                select RT_SERIAL_USING_DMA
                default n
        endif

    menuconfig BSP_USING_CAN
        bool "Enable CAN"
        default n
        select RT_USING_CAN
        if BSP_USING_CAN
            config BSP_USING_CAN1
                bool "using can1"
                default n
        endif

    menuconfig BSP_USING_ADC
        bool "Enable ADC"
        default n
        select RT_USING_ADC
        if BSP_USING_ADC
            config BSP_USING_ADC1
                bool "using adc1"
                default n
            config BSP_USING_ADC2
                bool "using adc2"
                default n
        endif

    menuconfig BSP_USING_RTC
        bool "Enable RTC"
        select RT_USING_RTC
        default n
        if BSP_USING_RTC
            choice
                prompt "Select clock source"
                default BSP_RTC_USING_LRC

                config BSP_RTC_USING_XTAL32
                    bool "RTC USING XTAL32"

                config BSP_RTC_USING_LRC
                    bool "RTC USING LRC"
            endchoice
        endif

    menuconfig BSP_USING_I2C2
        bool "Enable I2C2 BUS (software simulation)"
        default n
        select RT_USING_I2C
        select RT_USING_I2C_BITOPS
        select RT_USING_PIN
        if BSP_USING_I2C2
            config BSP_I2C2_SCL_PIN
                int "i2c2 scl pin number"
                range 1 100
                default 48
            config BSP_I2C2_SDA_PIN
                int "I2C2 sda pin number"
                range 1 100
                default 49
        endif

    config BSP_USING_WDT
        bool "Enable Watchdog Timer"
        select RT_USING_WDT
        default n

    menuconfig BSP_USING_PWM_TMRA
        bool "Enable timerA output PWM"
        depends on (!BSP_USING_UART3)
        default n
        select RT_USING_PWM
        if BSP_USING_PWM_TMRA
        menuconfig BSP_USING_PWM_TMRA_4
            bool "Enable timerA-4 output PWM"
            default n
            if BSP_USING_PWM_TMRA_4
                config BSP_USING_PWM_TMRA_4_CH7
                    bool "Enable timerA-4 channel7"
                    default n
                config BSP_USING_PWM_TMRA_4_CH8
                    bool "Enable timerA-4 channel8"
                    default n
            endif
        endif

endmenu

menu "Board extended module Drivers"

endmenu

endmenu