menu "Hardware Drivers Config" config SOC_STM32F429IG bool select SOC_SERIES_STM32F4 default y menu "Onboard Peripheral Drivers" config BSP_USING_USB_TO_USART bool "Enable USB TO USART (uart1)" select BSP_USING_UART select BSP_USING_UART1 default y config BSP_USING_RS232 bool "Enable RS232" select BSP_USING_UART select BSP_USING_UART2 default n config BSP_USING_SDRAM bool "Enable SDRAM" select BSP_USING_FMC default n config BSP_USING_SPI_FLASH bool "Enable SPI FLASH (W25Q128 spi5)" select BSP_USING_SPI select BSP_USING_SPI5 select RT_USING_SFUD select RT_SFUD_USING_SFDP default n config BSP_USING_LCD bool "Enable LCD" select BSP_USING_LTDC select BSP_USING_SDRAM default n config BSP_USING_MPU6050 bool "Enable MPU6050 (i2c1)" select BSP_USING_I2C1 select PKG_USING_MPU6XXX default n config PHY_USING_LAN8720A bool config BSP_USING_ETH bool "Enable Ethernet" default n select RT_USING_LWIP select PHY_USING_LAN8720A config BSP_USING_RGB bool "Enable RGB LED (timer5 channel1 - 3)" select RT_USING_PWM select BSP_USING_PWM select BSP_USING_PWM5 select BSP_USING_PWM5_CH1 select BSP_USING_PWM5_CH2 select BSP_USING_PWM5_CH3 default n config BSP_USING_POT bool "Enable potentiometer" select BSP_USING_ADC select BSP_USING_ADC1 default n config BSP_USING_SDCARD bool "Enable SDCARD (sdio)" select BSP_USING_SDIO select RT_USING_DFS select RT_USING_DFS_ELMFAT select RT_USING_PIN default n endmenu menu "On-chip Peripheral Drivers" config BSP_USING_GPIO bool "Enable GPIO" select RT_USING_PIN default y menuconfig BSP_USING_UART bool "Enable UART" default y select RT_USING_SERIAL if BSP_USING_UART config BSP_USING_UART1 bool "Enable UART1" default y config BSP_UART1_RX_USING_DMA bool "Enable UART1 RX DMA" depends on BSP_USING_UART1 && RT_SERIAL_USING_DMA default n config BSP_USING_UART2 bool "Enable UART2" default n config BSP_UART2_RX_USING_DMA bool "Enable UART2 RX DMA" depends on BSP_USING_UART2 && RT_SERIAL_USING_DMA default n endif config BSP_USING_ON_CHIP_FLASH bool "Enable on-chip FLASH" default n menuconfig BSP_USING_SPI bool "Enable SPI BUS" default n select RT_USING_SPI if BSP_USING_SPI config BSP_USING_SPI5 bool "Enable SPI5 BUS" default n config BSP_SPI5_TX_USING_DMA bool "Enable SPI5 TX DMA" depends on BSP_USING_SPI5 default n config BSP_SPI5_RX_USING_DMA bool "Enable SPI5 RX DMA" depends on BSP_USING_SPI5 select BSP_SPI5_TX_USING_DMA default n endif menuconfig BSP_USING_TIM bool "Enable timer" default n select RT_USING_HWTIMER if BSP_USING_TIM config BSP_USING_TIM11 bool "Enable TIM11" default n config BSP_USING_TIM13 bool "Enable TIM13" default n config BSP_USING_TIM14 bool "Enable TIM14" default n endif menuconfig BSP_USING_PWM bool "Enable pwm" default n select RT_USING_PWM if BSP_USING_PWM menuconfig BSP_USING_PWM5 bool "Enable timer5 output pwm" default n if BSP_USING_PWM5 config BSP_USING_PWM5_CH1 bool "Enable PWM5 channel1" default n config BSP_USING_PWM5_CH2 bool "Enable PWM5 channel2" default n config BSP_USING_PWM5_CH3 bool "Enable PWM5 channel3" default n endif endif menuconfig BSP_USING_ADC bool "Enable ADC" default n select RT_USING_ADC if BSP_USING_ADC config BSP_USING_ADC1 bool "Enable ADC1" default n endif menuconfig BSP_USING_I2C1 bool "Enable I2C1 BUS (software simulation)" default n select RT_USING_I2C select RT_USING_I2C_BITOPS select RT_USING_PIN if BSP_USING_I2C1 comment "Notice: PB6 --> 22; PB7 --> 23" config BSP_I2C1_SCL_PIN int "I2C1 scl pin number" range 1 176 default 22 config BSP_I2C1_SDA_PIN int "I2C1 sda pin number" range 1 176 default 23 endif menuconfig BSP_USING_ONCHIP_RTC bool "Enable RTC" select RT_USING_RTC select RT_USING_LIBC default n if BSP_USING_ONCHIP_RTC choice prompt "Select clock source" default BSP_RTC_USING_LSE config BSP_RTC_USING_LSE bool "RTC USING LSE" config BSP_RTC_USING_LSI bool "RTC USING LSI" endchoice endif config BSP_USING_WDT bool "Enable Watchdog Timer" select RT_USING_WDT default n config BSP_USING_SDIO bool "Enable SDIO" select RT_USING_SDIO select RT_USING_DFS default n config BSP_USING_FMC bool default n config BSP_USING_LTDC bool default n endmenu menu "Board extended module Drivers" endmenu endmenu