* [kernel][mem] Multiple instances of small memory allocation algorithm
* [kernel][mem] Change small memory management algorithm memory header flag
* [kernel][mem] Fix assertion problem
* [kernel][slab] Multiple instances of slab memory management algorithm
* [kernel][memheap] Remove rt_malloc/rt_free/rt_realloc and other related memory interfaces
* [kernel][mem] Clean up memory space of small memory management objects
* [kernel][kservice] Add memory application interface and thread protection interface
* [kernel][kservice] Fix function return value problem
* [kernel][memheap] Optimize memheaptrace print
* [kernel][memheap] Support best mode
* [kernel][memory] Remove semaphore lock
* [kernel][memheap] Add locked flag
* [kernel][memory] Support malloc memory in interrupt
* [kernel][memheap] Add 'memheapcheck' cmd
* [kernel][mem] Fix failure to request full memory
* [kernel][memheap] Fix compilation warning
* [kernel][mem] Fix mem realloc ASSERT
* [examples][testcases] Add small mem testcase
* [examples][mem_tc] Modify test memory size
* [examples][testcases] Add slab memory management algorithm test case
* [examples][testcases] fix small memory management algorithm test case
* [kernel][memory] Adjusting memory allocation algorithm object definition and interface
* [kernel][memory] Fix compilation warning
* [examples][utest] Fix mem test case
* [examples][utest] fix slab test case
* [utest][testcases] Shorten test time
* [kernel][memory] Formatting code
* [examples][utest] Adjust test run time
* [examples][utest] Formatting code
* [bsp] update all rtconfig.h
1. Add "drv_eth.c" for all imxrt platforms.
2. Add ksz8081 phy driver for imxrt1052-nxp-evk board.
3. Disable the LED demo in main.c file if enable the ENET
and ksz8081 phy, because the PINs of LED and ksz8081
reset are from the same GPIO.
4. Update the relevant Kconfig and Sconscript files.
Signed-off-by: Gavin Liu <gavin-liugang@outlook.com>
1. Add sdram item in bsp/imxrt/imxrt1052-nxp-evk/board/Kconfig
2. Add sdram configuration header file for imxrt1052-nxp-evk
3. Update the sdram space assignment for memheap
Signed-off-by: Gavin Liu <gavin-liugang@outlook.com>
Add PINs init function based on the selected UART port.
In general, user should configure all necessary PINs based on
the specific imxrt board in:
bsp/imxrt/xxxx/board/MCUX_Config/pin_mux.c
There is a convenient GUI tool named MCUXpresso Config Tools,
it's free and can be obtained from NXP offical website. Open
the file:
bsp/imxrt/imxrt1052-nxp-evk/board/MCUX_Config/MCUX_Config.mex
with MCUXpresso Config Tools, set the necessary PINs (or clocks)
and generate the new code of pin_mux.c (or clock_config.c), the
project can get right configurations based on specific imxrt
board.
But, there is no relation between RT-Thread Kconfig and MCUXpresso
Config Tools. User selects one driver in RT-Thread menuconfig, then
the ping_mux.c should be udpated by MCUXpresso Config Tools to set
the right PIN configurations for the selected driver. It's clear
but a little complex.
We add the PIN init functions for some drivers in the board.c file,
1. It's convenient to usr a driver in RT-Thread. Just select the
driver, then the code will include all necessary parts, and the
driver can work well.
2. User can also configure the PINs with MCUXpresso Config Tools.
3. The drivers in bsp/imxrt/libraries/drivers are common for all
imxrt boards. They may have different PIN configurations based
on different hardware design. So we put the PIN init functions
in each board.c file following each different imxrt board.
Signed-off-by: Gavin Liu <gavin-liugang@outlook.com>
Tangyuxin
Meco Man
guo
liukangcc
JCZou
wangqiang
WBI\nxf44444
Cathy Li
Ernest
chenyong
Gavin Liu
yangjie
LinJieqiang
SummerGift
yaomo718
misonyo