ROMFS is Read-Only Memory Filesystem. But ext4/fat are not read-only.
So renamed:
- mnt_romfs.c -> mnt_diskfs.c
- BSP_ROOTFS_TYPE_ROMFS -> BSP_ROOTFS_TYPE_DISKFS
Signed-off-by: Chen Wang <unicorn_wang@outlook.com>
CV18xx RISC-V C906L.
Configuration value for CPU and ARCH are already defined in rtconfig.py.
Remove these duplication from SConstruct.
Signed-off-by: Chen Wang <unicorn_wang@outlook.com>
After first called from uart open, the dw8250_uart_configure
API cannot be called again. Otherwise, this will mess up the
device, and uart will not act properly to interrupt again.
Analysis: Configure uart device will close recive interrupte,
causing uart device to malfunction.
Solution: After configure uart device, enable the device's
recive interrupte.
Signed-off-by: Shicheng Chu <1468559561@qq.com>
Reviewed-by: Chen Wang <unicorn_wang@outlook.com>
Supports both big and little cores of RISC-V C906,
but does not support ARM cores. Currently, only UART
drivers are supported on the peripherals.
Signed-off-by: Shicheng Chu <1468559561@qq.com>
For bsp/cvitek, all drivers related files are moved to the directory
bsp/cvitek/drivers, so the drivers_path_prefix processing in the
SConstruct of the three bsp projects can be simplified.
Signed-off-by: Chen Wang <unicorn_wang@outlook.com>
Analysis: The IRQ_MAX_NR value of c906_little is wrong.
interrupt.h relies on IRQ_MAX_NR defined in rtconfig.h but
does not explicitly include this header file.
Solution: Change IRQ_MAX_NR to the correct value 61 in
the datasheet. Explicitly include rtconfig.h in interrupt.h.
Signed-off-by: Shicheng Chu <1468559561@qq.com>
Reviewed-by: Chen Wang <unicorn_wang@outlook.com>
Analysis: The IRQ_MAX_NR value of cv18xx_risc-v is wrong.
The wrong IRQ_MAX_NR will cause the install of an interrupt
number larger than its value to fail.
Solution: Change IRQ_MAX_NR to the correct value 101 in
the datasheet.
Signed-off-by: Shicheng Chu <1468559561@qq.com>
Reviewed-by: Chen Wang <unicorn_wang@outlook.com>
Cvitek adc dirver only supports one adc controller now,
but the other adc controller RTCSYS_SARADC is missing.
Signed-off-by: Shicheng Chu <1468559561@qq.com>
Reviewed-by: Chen Wang <unicorn_wang@outlook.com>
Changes:
- board.c: add static assert for KERNEL_VADDR_START to check if it's valid
- board.h: updated deafult KERNEL_VADDR_START for standard version
- config bsp for v5.2.0 smart requirements
- kconfig: update bsp Kconfig for remap kernel
Signed-off-by: Shell <smokewood@qq.com>
Reviewed-on: https://github.com/RT-Thread/rt-thread/pull/9229
Reviewed-by: Chen Wang <unicorn_wang@outlook.com>
To support more choice on bootfs. romfs, cromfs are now supported on
risc_v_big platform.
Changes:
- added mount operations under port
- added prototypes for cromfs init APIs
Signed-off-by: Shell <smokewood@qq.com>
Reviewed-on: https://github.com/RT-Thread/rt-thread/pull/9229
Reviewed-by: Chen Wang <unicorn_wang@outlook.com>
The aarch64 core of duo on the master cannot enter the
console interface. It can only print the RT flag and hold it.
Analysis: The latest commit that can work is ae6a328 ("Add
psoc62, 61 config"). This phenomenon will occur after adding
754c59a ("[Feature] DFS mount auto by kernel parameters").
The specific reason is that when aarch bsp enables the device
tree, the current u-boot will pass in bootargs, which contains
"root=/dev/mmcblk0p2 rootwait rw", which means that the
kernel is required to wait until the rootfs in /dev/mmcblk0p2
loaded successfully. However, the current aarch64 bsp default
does not implement sdmmc device mounting, causing the
kernel file system mounting module (rootfs_mnt_init() of
components/drivers/core/mnt.c) to enter an infinite loop waiting.
Solution: At present, we do not plan to modify the startup
parameters of u-boot. The temporary solution adopted is to
create a pseudo /dev/mmcblk0p2 device during the board
initialization process, and then cancel the pseudo device
after mnt is completed. This allows the kernel boot to be
completed successfully.
Signed-off-by: Shicheng Chu <1468559561@qq.com>
Reviewed-by: Chen Wang <unicorn_wang@outlook.com>
In the original Sconstruct script, `GetDepend('__STACKSIZE__')`
is placed before the call to `PrepareBuilding()`, which causes
the value of `GetDepend('__STACKSIZE__')` to always be False,
and the value of `__STACKSIZE__` in `link_stacksize.lds` will
not be updated.
Solution: move the call if `PrepareBuilding()` ahead.
Also sync and update the .config and rtconfig.h, plus the
link_stacksize.lds.
Signed-off-by: Chen Wang <unicorn_wang@outlook.com>
When compiling CV18xx_arch64, have a error:
can not find "rt_fdt_commit_memregion_early"
Analysis: b785ef9 ("[libcpu][aarch64]memory setup using memblock ")
no longer support "rt_fdt_commit_memregion_early", become use
"rt_memblock_reserve_memory"
Solution: Refer to the bsp/qemu-virt64-aarch64/drivers/board.c
delete "rt_fdt_commit_memregion_early"
Signed-off-by: Shicheng Chu <1468559561@qq.com>
Reviewed-by: Chen Wang <unicorn_wang@outlook.com>
When compiling CV18xx_arch64, there are the following errors:
1. missing soc type for aarch64
2. uart device objects defined but not used
Analysis: a63c07f ("bsp: cvitek: new design for pinmux") and
114e143("bsp:cvitek: add pinmux for uart"), CV18xx_arch64 is not
considered.
Solution: Refer to the cv18xx_riscv format to add the corresponding
chip type SOC_Type_SG2002, as well as the corresponding macro
for the serial port pins and interrupts
Signed-off-by: Shicheng Chu <1468559561@qq.com>
Reviewed-by: Chen Wang <unicorn_wang@outlook.com>
Currently, the documents under bsp/cvitek are a bit
messy. There are currently four readme files:
- bsp/cvitek/README.md (Chinese)
- bsp/cvitek/c906_little/README.md (Chinese/English)
- bsp/cvitek/cv18xx_aarch64/README.md (Chinese)
- bsp/cvitek/cv18xx_risc-v/README.md (Chinese/English)
Regarding the working mode of the big + small cores, it
is meaningless to describe the small core alone, or the
large core alone. This can also be seen in the existing
files. The readme of the small core will also introduce
the programming of the large core, and vice versa.
Considering that the official default mode is
C906B + C906L. ARM large core can be treataed as a
special case. So the document structure is modified as
follows:
- Remove `bsp/cvitek/c906_little/README.md` and
`bsp/cvitek/cv18xx_risc-v/README.md`, merge them all
into `bsp/cvitek/README.md`
- Add a link to `bsp/cvitek/cv18xx_aarch64/README.md`
in `bsp/cvitek/README.md`
FIXME: The modified document does not provide English
version. Is it really necessary?
Signed-off-by: Chen Wang <unicorn_wang@outlook.com>
Some drivers use INIT_BOARD_EXPORT, it is not necessary,
it is enough to use INIT_DEVICE_EXPORT for genearl drivers.
Signed-off-by: Chen Wang <unicorn_wang@outlook.com>
See `components/drivers/include/drivers/watchdog.h`
maco definition of
RT_DEVICE_CTRL_WDT_GET_TIMEOUT
RT_DEVICE_CTRL_WDT_SET_TIMEOUT
RT_DEVICE_CTRL_WDT_GET_TIMELEFT
The wdt timeout time unit is defined as seconds in the API, but
the code incorrectly uses ms.
Correct this and comply with the API definition.
Signed-off-by: Chen Wang <unicorn_wang@outlook.com>
Reviewed-by: Yuanjie He <943313837@qq.com>
Reviewed-by: Shell <smokewood@qq.com>
Rewrote the spi driver.
Reuse the driver code from https://github.com/sophgo/cvi_alios_open,
which is Apache 2.0 licenced.
Signed-off-by: flyingcys <flyingcys@163.com>
Reviewed-by: Chen Wang <unicorn_wang@outlook.com>
```
./bsp/cvitek/drivers/drv_wdt.c: In function '_wdt_control':
warning: assignment to 'void *' from 'unsigned int' makes pointer
from integer without a cast [-Wint-conversion]
119 | wdt_device->parent.user_data = (rt_uint32_t)(*(rt_uint32_t *)arg);
| ^
warning: cast from pointer to integer of different size [-Wpointer-to-int-cast]
122 | *(rt_uint32_t *)arg = (rt_uint32_t)wdt_device->parent.user_data;
| ^
```
Rootcasue: It's not portable to store integar in a pointer.
Solution: use global _wdt_dev to store the timeout value.
Signed-off-by: Chen Wang <unicorn_wang@outlook.com>
The ADC controller needs to be calibrated during the initialization
phase, otherwise the measured voltage value will be inaccurate.
Signed-off-by: Chen Wang <unicorn_wang@outlook.com>
In the new design, we require the user to manually enter the
PinName (as a string) in menuconfig instead of being given
menu items to select.
The original method will lead to too many menu item-related
macros being defined in the code, causing ifdef and other
codes scatter everywhere in the driver code, which is
inconvenient to maintain.
The new design adds a pinmux driver module to manage the
multiplexing of pins. This patch provides this driver module.
P.S., the reason why users are allowed to specify pinname
in a string instead of the pin number is mainly because
the technical manual provided by the SOC manufacturer
does not have numbers for some pins, only names.
Signed-off-by: Chen Wang <unicorn_wang@outlook.com>
Reviewed-by: Yuanjie He <943313837@qq.com>
Reviewed-by: Shell <smokewood@qq.com>
Chen Wang
flyingcys
Meco Man
Alex Imcu
Yuqiang Wang
imcu
CXSforHPU
Z8MAN8
heyuanjie87
Shell
Bernard Xiong