Merge pull request #2223 from e31207077/stm32f767-st-nucleo

增加 ST 官方 stm32f767-nucleo 开发板

bsp/stm32/stm32f767-st-nucleo/Kconfig

@@ -0,0 +1,21 @@
+mainmenu "RT-Thread Configuration"
+
+config $BSP_DIR
+    string
+    option env="BSP_ROOT"
+    default "."
+
+config $RTT_DIR
+    string
+    option env="RTT_ROOT"
+    default "../../.."
+
+config $PKGS_DIR
+    string
+    option env="PKGS_ROOT"
+    default "packages"
+ 
+source "$RTT_DIR/Kconfig"
+source "$PKGS_DIR/Kconfig"
+source "../libraries/Kconfig"
+source "board/Kconfig"

bsp/stm32/stm32f767-st-nucleo/README.md

@@ -0,0 +1,110 @@
+# STM32F767 NUCLEO-F767ZI开发板 BSP 说明
+## 简介
+
+本文档为 NUCLEO-F767ZI 开发板的 BSP (板级支持包) 说明。
+
+主要内容如下：
+
+- 开发板资源介绍
+- BSP 快速上手
+- 进阶使用方法
+
+通过阅读快速上手章节开发者可以快速地上手该 BSP，将 RT-Thread 运行在开发板上。在进阶使用指南章节，将会介绍更多高级功能，帮助开发者利用 RT-Thread 驱动更多板载资源。
+
+## 开发板介绍
+
+NUCLEO-F767ZI 是st推出的一款基于 ARM Cortex-M7 内核的开发板，最高主频为 216Mhz，该开发板具有丰富的板载资源，可以充分发挥 STM32F767 的芯片性能。
+
+开发板外观如下图所示：
+
+![board](figures/en.high-perf_nucleo-144_mbed.jpg)
+
+该开发板常用 **板载资源** 如下：
+
+- MCU：STM32f767，主频 216MHz，2MB FLASH ，512KB RAM ，16K CACHE
+
+- 常用外设
+  - LED ：3个，LED1 (绿色，PB0),LED2（蓝色，PB7），LED3（红色，PB14）
+  - 按键：2个，B1（用户按键，PC13），B2（复位引脚）
+- 常用接口：USB 转串口3、以太网接口
+- 调试接口：ST-LINK
+
+开发板更多详细信息请参考ST [NUCLEO-F767ZI开发板介绍](https://www.st.com/en/evaluation-tools/nucleo-f767zi.html)。
+
+## 外设支持
+
+本 BSP 目前对外设的支持情况如下：
+
+| **板载外设**      | **支持情况** | **备注**                              |
+| :-----------------| :----------: | :-------------------------------------|
+| USB 转串口3        |     支持     |                                       |
+| 以太网            |   暂不支持   | 即将支持                              |
+| **片上外设**      | **支持情况** | **备注**                              |
+| GPIO              |     支持     | PA0, PA1... PK15 ---> PIN: 0, 1...144 |
+| UART              |     支持     | UART3                                 |
+| **扩展模块**      | **支持情况** | **备注**                              |
+| 暂无              |   暂不支持   | 暂不支持                              |
+
+## 使用说明
+
+使用说明分为如下两个章节：
+
+- 快速上手
+
+    本章节是为刚接触 RT-Thread 的新手准备的使用说明，遵循简单的步骤即可将 RT-Thread 操作系统运行在该开发板上，看到实验效果 。
+
+- 进阶使用
+
+    本章节是为需要在 RT-Thread 操作系统上使用更多开发板资源的开发者准备的。通过使用 ENV 工具对 BSP 进行配置，可以开启更多板载资源，实现更多高级功能。
+
+
+### 快速上手
+
+本 BSP 为开发者提供 MDK5 和 IAR 工程，并且支持 GCC 开发环境。下面以 MDK5 开发环境为例，介绍如何将系统运行起来。
+
+#### 硬件连接
+
+使用数据线连接开发板到 PC，打开电源开关。
+
+#### 编译下载
+
+双击 project.uvprojx 文件，打开 MDK5 工程，编译并下载程序到开发板。
+
+> 工程默认配置使用 ST-LINK 仿真器下载程序，在通过 ST-LINK 连接开发板的基础上，点击下载按钮即可下载程序到开发板
+
+#### 运行结果
+
+下载程序成功之后，系统会自动运行，LED 闪烁。
+
+连接开发板对应串口到 PC , 在终端工具里打开相应的串口（115200-8-1-N），复位设备后，可以看到 RT-Thread 的输出信息:
+
+```bash
+ \ | /
+- RT -     Thread Operating System
+ / | \     4.0.0 build Jan  9 2019
+ 2006 - 2018 Copyright by rt-thread team
+msh >
+```
+### 进阶使用
+
+此 BSP 默认只开启了 GPIO 和 串口3 的功能，如果需使用 Ethernet 等更多高级功能，需要利用 ENV 工具对BSP 进行配置，步骤如下：
+
+1. 在 bsp 下打开 env 工具。
+
+2. 输入`menuconfig`命令配置工程，配置好之后保存退出。
+
+3. 输入`pkgs --update`命令更新软件包。
+
+4. 输入`scons --target=mdk4/mdk5/iar` 命令重新生成工程。
+
+本章节更多详细的介绍请参考 [STM32 系列 BSP 外设驱动使用教程](../docs/STM32系列BSP外设驱动使用教程.md)。
+
+## 注意事项
+
+暂无
+
+## 联系人信息
+
+维护人:
+
+-  [e31207077](https://github.com/e31207077), 邮箱：<e31207077@yahoo.com.tw>

bsp/stm32/stm32f767-st-nucleo/SConscript

@@ -0,0 +1,14 @@
+# for module compiling
+import os
+Import('RTT_ROOT')
+
+cwd = str(Dir('#'))
+objs = []
+list = os.listdir(cwd)
+
+for d in list:
+    path = os.path.join(cwd, d)
+    if os.path.isfile(os.path.join(path, 'SConscript')):
+        objs = objs + SConscript(os.path.join(d, 'SConscript'))
+
+Return('objs')

bsp/stm32/stm32f767-st-nucleo/SConstruct

@@ -0,0 +1,47 @@
+import os
+import sys
+import rtconfig
+
+if os.getenv('RTT_ROOT'):
+    RTT_ROOT = os.getenv('RTT_ROOT')
+else:
+    RTT_ROOT = os.path.normpath(os.getcwd() + '/../../..')
+
+sys.path = sys.path + [os.path.join(RTT_ROOT, 'tools')]
+try:
+    from building import *
+except:
+    print('Cannot found RT-Thread root directory, please check RTT_ROOT')
+    print(RTT_ROOT)
+    exit(-1)
+
+TARGET = 'rt-thread.' + rtconfig.TARGET_EXT
+
+env = Environment(tools = ['mingw'],
+    AS = rtconfig.AS, ASFLAGS = rtconfig.AFLAGS,
+    CC = rtconfig.CC, CCFLAGS = rtconfig.CFLAGS,
+    AR = rtconfig.AR, ARFLAGS = '-rc',
+    LINK = rtconfig.LINK, LINKFLAGS = rtconfig.LFLAGS)
+env.PrependENVPath('PATH', rtconfig.EXEC_PATH)
+
+if rtconfig.PLATFORM == 'iar':
+    env.Replace(CCCOM = ['$CC $CCFLAGS $CPPFLAGS $_CPPDEFFLAGS $_CPPINCFLAGS -o $TARGET $SOURCES'])
+    env.Replace(ARFLAGS = [''])
+    env.Replace(LINKCOM = ['$LINK $SOURCES $LINKFLAGS -o $TARGET --map rt-thread.map'])
+
+Export('RTT_ROOT')
+Export('rtconfig')
+
+# prepare building environment
+objs = PrepareBuilding(env, RTT_ROOT, has_libcpu=False)
+
+SDK_ROOT = os.path.abspath('./')
+
+# include drivers
+objs.extend(SConscript(os.path.dirname(SDK_ROOT) + '/libraries/STM32F7xx_HAL/SConscript'))
+
+# include libraries
+objs.extend(SConscript(os.path.dirname(SDK_ROOT) + '/libraries/HAL_Drivers/SConscript'))
+
+# make a building
+DoBuilding(TARGET, objs)

bsp/stm32/stm32f767-st-nucleo/applications/SConscript

@@ -0,0 +1,12 @@
+import rtconfig
+from building import *
+
+cwd     = GetCurrentDir()
+CPPPATH = [cwd, str(Dir('#'))]
+src     = Split("""
+main.c
+""")
+
+group = DefineGroup('Applications', src, depend = [''], CPPPATH = CPPPATH)
+
+Return('group')

bsp/stm32/stm32f767-st-nucleo/applications/main.c

@@ -0,0 +1,35 @@
+/*
+ * Copyright (c) 2006-2018, RT-Thread Development Team
+ *
+ * SPDX-License-Identifier: Apache-2.0
+ *
+ * Change Logs:
+ * Date           Author       Notes
+ * 2018-11-06     SummerGift   change to new framework
+ * 2019-1-10      e31207077    change to new framework
+ */
+
+#include <rtthread.h>
+#include <rtdevice.h>
+#include <board.h>
+#include "drv_gpio.h"
+
+/* defined the LED1 pin: PB0 */
+#define LED1_PIN    GET_PIN(B, 0)
+
+int main(void)
+{
+    int count = 1;
+    /* set LED1 pin mode to output */
+    rt_pin_mode(LED1_PIN, PIN_MODE_OUTPUT);
+
+    while (count++)
+    {
+        rt_pin_write(LED1_PIN, PIN_HIGH);
+        rt_thread_mdelay(500);
+        rt_pin_write(LED1_PIN, PIN_LOW);
+        rt_thread_mdelay(500);
+    }
+
+    return RT_EOK;		
+}

bsp/stm32/stm32f767-st-nucleo/board/CubeMX_Config/CubeMX_Config.ioc

@@ -0,0 +1,324 @@
+#MicroXplorer Configuration settings - do not modify
+ETH.IPParameters=MediaInterface,PHY_Name,PHY_Value,PhyAddress
+ETH.MediaInterface=ETH_MEDIA_INTERFACE_RMII
+ETH.PHY_Name=LAN8742A_PHY_ADDRESS
+ETH.PHY_Value=0
+ETH.PhyAddress=0
+File.Version=6
+KeepUserPlacement=true
+Mcu.Family=STM32F7
+Mcu.IP0=CORTEX_M7
+Mcu.IP1=ETH
+Mcu.IP2=NVIC
+Mcu.IP3=RCC
+Mcu.IP4=SYS
+Mcu.IP5=USART3
+Mcu.IP6=USB_OTG_FS
+Mcu.IPNb=7
+Mcu.Name=STM32F767ZITx
+Mcu.Package=LQFP144
+Mcu.Pin0=PC13
+Mcu.Pin1=PC14/OSC32_IN
+Mcu.Pin10=PC5
+Mcu.Pin11=PB13
+Mcu.Pin12=PB14
+Mcu.Pin13=PD8
+Mcu.Pin14=PD9
+Mcu.Pin15=PG6
+Mcu.Pin16=PG7
+Mcu.Pin17=PA8
+Mcu.Pin18=PA9
+Mcu.Pin19=PA10
+Mcu.Pin2=PC15/OSC32_OUT
+Mcu.Pin20=PA11
+Mcu.Pin21=PA12
+Mcu.Pin22=PA13
+Mcu.Pin23=PA14
+Mcu.Pin24=PG11
+Mcu.Pin25=PG13
+Mcu.Pin26=PB3
+Mcu.Pin27=PB7
+Mcu.Pin28=VP_SYS_VS_Systick
+Mcu.Pin3=PH0/OSC_IN
+Mcu.Pin4=PH1/OSC_OUT
+Mcu.Pin5=PC1
+Mcu.Pin6=PA1
+Mcu.Pin7=PA2
+Mcu.Pin8=PA7
+Mcu.Pin9=PC4
+Mcu.PinsNb=29
+Mcu.ThirdPartyNb=0
+Mcu.UserConstants=
+Mcu.UserName=STM32F767ZITx
+MxCube.Version=5.0.1
+MxDb.Version=DB.5.0.1
+NVIC.BusFault_IRQn=true\:0\:0\:false\:false\:true\:true
+NVIC.DebugMonitor_IRQn=true\:0\:0\:false\:false\:true\:true
+NVIC.HardFault_IRQn=true\:0\:0\:false\:false\:true\:true
+NVIC.MemoryManagement_IRQn=true\:0\:0\:false\:false\:true\:true
+NVIC.NonMaskableInt_IRQn=true\:0\:0\:false\:false\:true\:true
+NVIC.PendSV_IRQn=true\:0\:0\:false\:false\:true\:true
+NVIC.PriorityGroup=NVIC_PRIORITYGROUP_4
+NVIC.SVCall_IRQn=true\:0\:0\:false\:false\:true\:true
+NVIC.SysTick_IRQn=true\:0\:0\:false\:false\:true\:true
+NVIC.UsageFault_IRQn=true\:0\:0\:false\:false\:true\:true
+PA1.GPIOParameters=GPIO_Label
+PA1.GPIO_Label=RMII_REF_CLK [LAN8742A-CZ-TR_REFCLK0]
+PA1.Locked=true
+PA1.Mode=RMII
+PA1.Signal=ETH_REF_CLK
+PA10.GPIOParameters=GPIO_Label
+PA10.GPIO_Label=USB_ID
+PA10.Locked=true
+PA10.Signal=USB_OTG_FS_ID
+PA11.GPIOParameters=GPIO_Label
+PA11.GPIO_Label=USB_DM
+PA11.Locked=true
+PA11.Mode=Device_Only
+PA11.Signal=USB_OTG_FS_DM
+PA12.GPIOParameters=GPIO_Label
+PA12.GPIO_Label=USB_DP
+PA12.Locked=true
+PA12.Mode=Device_Only
+PA12.Signal=USB_OTG_FS_DP
+PA13.GPIOParameters=GPIO_Label
+PA13.GPIO_Label=TMS
+PA13.Locked=true
+PA13.Mode=Serial_Wire
+PA13.Signal=SYS_JTMS-SWDIO
+PA14.GPIOParameters=GPIO_Label
+PA14.GPIO_Label=TCK
+PA14.Locked=true
+PA14.Mode=Serial_Wire
+PA14.Signal=SYS_JTCK-SWCLK
+PA2.GPIOParameters=GPIO_Label
+PA2.GPIO_Label=RMII_MDIO [LAN8742A-CZ-TR_MDIO]
+PA2.Locked=true
+PA2.Mode=RMII
+PA2.Signal=ETH_MDIO
+PA7.GPIOParameters=GPIO_Label
+PA7.GPIO_Label=RMII_CRS_DV [LAN8742A-CZ-TR_CRS_DV]
+PA7.Locked=true
+PA7.Mode=RMII
+PA7.Signal=ETH_CRS_DV
+PA8.GPIOParameters=GPIO_Label
+PA8.GPIO_Label=USB_SOF [TP1]
+PA8.Locked=true
+PA8.Mode=Activate_SOF_FS
+PA8.Signal=USB_OTG_FS_SOF
+PA9.GPIOParameters=GPIO_Label
+PA9.GPIO_Label=USB_VBUS
+PA9.Locked=true
+PA9.Mode=Activate_VBUS
+PA9.Signal=USB_OTG_FS_VBUS
+PB13.GPIOParameters=GPIO_Label
+PB13.GPIO_Label=RMII_TXD1 [LAN8742A-CZ-TR_TXD1]
+PB13.Locked=true
+PB13.Mode=RMII
+PB13.Signal=ETH_TXD1
+PB14.GPIOParameters=GPIO_Label
+PB14.GPIO_Label=LD3 [Red]
+PB14.Locked=true
+PB14.Signal=GPIO_Output
+PB3.GPIOParameters=GPIO_Label
+PB3.GPIO_Label=SWO
+PB3.Locked=true
+PB3.Signal=SYS_JTDO-SWO
+PB7.GPIOParameters=GPIO_Label
+PB7.GPIO_Label=LD2 [Blue]
+PB7.Locked=true
+PB7.Signal=GPIO_Output
+PC1.GPIOParameters=GPIO_Label
+PC1.GPIO_Label=RMII_MDC [LAN8742A-CZ-TR_MDC]
+PC1.Locked=true
+PC1.Mode=RMII
+PC1.Signal=ETH_MDC
+PC13.GPIOParameters=GPIO_Label
+PC13.GPIO_Label=USER_Btn [B1]
+PC13.Locked=true
+PC13.Signal=GPXTI13
+PC14/OSC32_IN.Locked=true
+PC14/OSC32_IN.Mode=LSE-External-Oscillator
+PC14/OSC32_IN.Signal=RCC_OSC32_IN
+PC15/OSC32_OUT.Locked=true
+PC15/OSC32_OUT.Mode=LSE-External-Oscillator
+PC15/OSC32_OUT.Signal=RCC_OSC32_OUT
+PC4.GPIOParameters=GPIO_Label
+PC4.GPIO_Label=RMII_RXD0 [LAN8742A-CZ-TR_RXD0]
+PC4.Locked=true
+PC4.Mode=RMII
+PC4.Signal=ETH_RXD0
+PC5.GPIOParameters=GPIO_Label
+PC5.GPIO_Label=RMII_RXD1 [LAN8742A-CZ-TR_RXD1]
+PC5.Locked=true
+PC5.Mode=RMII
+PC5.Signal=ETH_RXD1
+PCC.Checker=false
+PCC.Line=STM32F7x7
+PCC.MCU=STM32F767ZITx
+PCC.PartNumber=STM32F767ZITx
+PCC.Seq0=0
+PCC.Series=STM32F7
+PCC.Temperature=25
+PCC.Vdd=3.6
+PD8.GPIOParameters=GPIO_Label
+PD8.GPIO_Label=STLK_RX [STM32F103CBT6_PA3]
+PD8.Locked=true
+PD8.Mode=Asynchronous
+PD8.Signal=USART3_TX
+PD9.GPIOParameters=GPIO_Label
+PD9.GPIO_Label=STLK_TX [STM32F103CBT6_PA2]
+PD9.Locked=true
+PD9.Mode=Asynchronous
+PD9.Signal=USART3_RX
+PG11.GPIOParameters=GPIO_Label
+PG11.GPIO_Label=RMII_TX_EN [LAN8742A-CZ-TR_TXEN]
+PG11.Locked=true
+PG11.Mode=RMII
+PG11.Signal=ETH_TX_EN
+PG13.GPIOParameters=GPIO_Label
+PG13.GPIO_Label=RMII_TXD0 [LAN8742A-CZ-TR_TXD0]
+PG13.Locked=true
+PG13.Mode=RMII
+PG13.Signal=ETH_TXD0
+PG6.GPIOParameters=GPIO_Label
+PG6.GPIO_Label=USB_PowerSwitchOn [STMPS2151STR_EN]
+PG6.Locked=true
+PG6.Signal=GPIO_Output
+PG7.GPIOParameters=GPIO_Label
+PG7.GPIO_Label=USB_OverCurrent [STMPS2151STR_FAULT]
+PG7.Locked=true
+PG7.Signal=GPIO_Input
+PH0/OSC_IN.GPIOParameters=GPIO_Label
+PH0/OSC_IN.GPIO_Label=MCO [STM32F103CBT6_PA8]
+PH0/OSC_IN.Locked=true
+PH0/OSC_IN.Mode=HSE-External-Clock-Source
+PH0/OSC_IN.Signal=RCC_OSC_IN
+PH1/OSC_OUT.Locked=true
+PH1/OSC_OUT.Mode=HSE-External-Clock-Source
+PH1/OSC_OUT.Signal=RCC_OSC_OUT
+PinOutPanel.RotationAngle=0
+ProjectManager.AskForMigrate=true
+ProjectManager.BackupPrevious=false
+ProjectManager.CompilerOptimize=6
+ProjectManager.ComputerToolchain=false
+ProjectManager.CoupleFile=false
+ProjectManager.CustomerFirmwarePackage=
+ProjectManager.DefaultFWLocation=true
+ProjectManager.DeletePrevious=true
+ProjectManager.DeviceId=STM32F767ZITx
+ProjectManager.FirmwarePackage=STM32Cube FW_F7 V1.14.0
+ProjectManager.FreePins=false
+ProjectManager.HalAssertFull=false
+ProjectManager.HeapSize=0x200
+ProjectManager.KeepUserCode=true
+ProjectManager.LastFirmware=true
+ProjectManager.LibraryCopy=0
+ProjectManager.MainLocation=Src
+ProjectManager.NoMain=false
+ProjectManager.PreviousToolchain=
+ProjectManager.ProjectBuild=false
+ProjectManager.ProjectFileName=CubeMX_Config.ioc
+ProjectManager.ProjectName=CubeMX_Config
+ProjectManager.StackSize=0x400
+ProjectManager.TargetToolchain=EWARM V8
+ProjectManager.ToolChainLocation=
+ProjectManager.UnderRoot=false
+ProjectManager.functionlistsort=1-MX_GPIO_Init-GPIO-false-HAL-true,2-SystemClock_Config-RCC-false-HAL-false,3-MX_CORTEX_M7_Init-CORTEX_M7-false-HAL-true,4-MX_ETH_Init-ETH-false-HAL-true,5-MX_USART3_UART_Init-USART3-false-HAL-true,6-MX_USB_OTG_FS_PCD_Init-USB_OTG_FS-false-HAL-true
+RCC.48MHZClocksFreq_Value=24000000
+RCC.ADC12outputFreq_Value=72000000
+RCC.ADC34outputFreq_Value=72000000
+RCC.AHBFreq_Value=216000000
+RCC.APB1CLKDivider=RCC_HCLK_DIV4
+RCC.APB1Freq_Value=54000000
+RCC.APB1TimFreq_Value=108000000
+RCC.APB2CLKDivider=RCC_HCLK_DIV2
+RCC.APB2Freq_Value=108000000
+RCC.APB2TimFreq_Value=216000000
+RCC.CECFreq_Value=32786.88524590164
+RCC.CortexFreq_Value=216000000
+RCC.DFSDMAudioFreq_Value=96000000
+RCC.DFSDMFreq_Value=108000000
+RCC.EthernetFreq_Value=216000000
+RCC.FCLKCortexFreq_Value=216000000
+RCC.FamilyName=M
+RCC.HCLKFreq_Value=216000000
+RCC.HSE_VALUE=8000000
+RCC.HSI_VALUE=16000000
+RCC.I2C1Freq_Value=54000000
+RCC.I2C2Freq_Value=54000000
+RCC.I2C3Freq_Value=54000000
+RCC.I2C4Freq_Value=54000000
+RCC.I2SClocksFreq_Value=48000000
+RCC.I2SFreq_Value=96000000
+RCC.IPParameters=48MHZClocksFreq_Value,ADC12outputFreq_Value,ADC34outputFreq_Value,AHBFreq_Value,APB1CLKDivider,APB1Freq_Value,APB1TimFreq_Value,APB2CLKDivider,APB2Freq_Value,APB2TimFreq_Value,CECFreq_Value,CortexFreq_Value,DFSDMAudioFreq_Value,DFSDMFreq_Value,EthernetFreq_Value,FCLKCortexFreq_Value,FamilyName,HCLKFreq_Value,HSE_VALUE,HSI_VALUE,I2C1Freq_Value,I2C2Freq_Value,I2C3Freq_Value,I2C4Freq_Value,I2SClocksFreq_Value,I2SFreq_Value,LCDTFTFreq_Value,LCDTFToutputFreq_Value,LPTIM1Freq_Value,LSI_VALUE,MCO1PinFreq_Value,MCO2PinFreq_Value,MCOFreq_Value,PLLCLKFreq_Value,PLLI2SPCLKFreq_Value,PLLI2SQCLKFreq_Value,PLLI2SRCLKFreq_Value,PLLI2SRoutputFreq_Value,PLLM,PLLMCOFreq_Value,PLLMUL,PLLN,PLLQ,PLLQCLKFreq_Value,PLLQoutputFreq_Value,PLLRFreq_Value,PLLSAIPCLKFreq_Value,PLLSAIQCLKFreq_Value,PLLSAIRCLKFreq_Value,PLLSAIoutputFreq_Value,PRESCALERUSB,RNGFreq_Value,RTCFreq_Value,RTCHSEDivFreq_Value,SAI1Freq_Value,SAI2Freq_Value,SDMMC2Freq_Value,SDMMCFreq_Value,SPDIFRXFreq_Value,SYSCLKFreq_VALUE,SYSCLKSource,SYSCLKSourceVirtual,TIM15Freq_Value,TIM16Freq_Value,TIM17Freq_Value,TIM1Freq_Value,TIM20Freq_Value,TIM2Freq_Value,TIM3Freq_Value,TIM8Freq_Value,UART4Freq_Value,UART5Freq_Value,UART7Freq_Value,UART8Freq_Value,USART1Freq_Value,USART2Freq_Value,USART3Freq_Value,USART6Freq_Value,USBFreq_Value,VCOI2SOutputFreq_Value,VCOInputFreq_Value,VCOOutput2Freq_Value,VCOOutputFreq_Value,VCOSAIOutputFreq_Value,VcooutputI2S,WatchDogFreq_Value
+RCC.LCDTFTFreq_Value=48000000
+RCC.LCDTFToutputFreq_Value=96000000
+RCC.LPTIM1Freq_Value=54000000
+RCC.LSI_VALUE=32000
+RCC.MCO1PinFreq_Value=16000000
+RCC.MCO2PinFreq_Value=216000000
+RCC.MCOFreq_Value=72000000
+RCC.PLLCLKFreq_Value=216000000
+RCC.PLLI2SPCLKFreq_Value=96000000
+RCC.PLLI2SQCLKFreq_Value=96000000
+RCC.PLLI2SRCLKFreq_Value=96000000
+RCC.PLLI2SRoutputFreq_Value=96000000
+RCC.PLLM=8
+RCC.PLLMCOFreq_Value=72000000
+RCC.PLLMUL=RCC_PLL_MUL9
+RCC.PLLN=432
+RCC.PLLQ=9
+RCC.PLLQCLKFreq_Value=48000000
+RCC.PLLQoutputFreq_Value=48000000
+RCC.PLLRFreq_Value=216000000
+RCC.PLLSAIPCLKFreq_Value=96000000
+RCC.PLLSAIQCLKFreq_Value=96000000
+RCC.PLLSAIRCLKFreq_Value=96000000
+RCC.PLLSAIoutputFreq_Value=96000000
+RCC.PRESCALERUSB=RCC_USBCLKSOURCE_PLL_DIV1_5
+RCC.RNGFreq_Value=48000000
+RCC.RTCFreq_Value=32000
+RCC.RTCHSEDivFreq_Value=4000000
+RCC.SAI1Freq_Value=96000000
+RCC.SAI2Freq_Value=96000000
+RCC.SDMMC2Freq_Value=216000000
+RCC.SDMMCFreq_Value=216000000
+RCC.SPDIFRXFreq_Value=96000000
+RCC.SYSCLKFreq_VALUE=216000000
+RCC.SYSCLKSource=RCC_SYSCLKSOURCE_PLLCLK
+RCC.SYSCLKSourceVirtual=RCC_SYSCLKSOURCE_PLLCLK
+RCC.TIM15Freq_Value=72000000
+RCC.TIM16Freq_Value=72000000
+RCC.TIM17Freq_Value=72000000
+RCC.TIM1Freq_Value=72000000
+RCC.TIM20Freq_Value=72000000
+RCC.TIM2Freq_Value=72000000
+RCC.TIM3Freq_Value=72000000
+RCC.TIM8Freq_Value=72000000
+RCC.UART4Freq_Value=54000000
+RCC.UART5Freq_Value=54000000
+RCC.UART7Freq_Value=54000000
+RCC.UART8Freq_Value=54000000
+RCC.USART1Freq_Value=108000000
+RCC.USART2Freq_Value=54000000
+RCC.USART3Freq_Value=54000000
+RCC.USART6Freq_Value=108000000
+RCC.USBFreq_Value=48000000
+RCC.VCOI2SOutputFreq_Value=192000000
+RCC.VCOInputFreq_Value=1000000
+RCC.VCOOutput2Freq_Value=8000000
+RCC.VCOOutputFreq_Value=432000000
+RCC.VCOSAIOutputFreq_Value=192000000
+RCC.VcooutputI2S=48000000
+RCC.WatchDogFreq_Value=32000
+SH.GPXTI13.0=GPIO_EXTI13
+SH.GPXTI13.ConfNb=1
+USART3.IPParameters=VirtualMode-Asynchronous
+USART3.VirtualMode-Asynchronous=VM_ASYNC
+USB_OTG_FS.IPParameters=VirtualMode
+USB_OTG_FS.VirtualMode=Device_Only
+VP_SYS_VS_Systick.Mode=SysTick
+VP_SYS_VS_Systick.Signal=SYS_VS_Systick
+board=NUCLEO-F767ZI
+boardIOC=true

bsp/stm32/stm32f767-st-nucleo/board/CubeMX_Config/Inc/main.h

@@ -0,0 +1,141 @@
+/* USER CODE BEGIN Header */
+/**
+  ******************************************************************************
+  * @file           : main.h
+  * @brief          : Header for main.c file.
+  *                   This file contains the common defines of the application.
+  ******************************************************************************
+  ** This notice applies to any and all portions of this file
+  * that are not between comment pairs USER CODE BEGIN and
+  * USER CODE END. Other portions of this file, whether 
+  * inserted by the user or by software development tools
+  * are owned by their respective copyright owners.
+  *
+  * COPYRIGHT(c) 2018 STMicroelectronics
+  *
+  * Redistribution and use in source and binary forms, with or without modification,
+  * are permitted provided that the following conditions are met:
+  *   1. Redistributions of source code must retain the above copyright notice,
+  *      this list of conditions and the following disclaimer.
+  *   2. Redistributions in binary form must reproduce the above copyright notice,
+  *      this list of conditions and the following disclaimer in the documentation
+  *      and/or other materials provided with the distribution.
+  *   3. Neither the name of STMicroelectronics nor the names of its contributors
+  *      may be used to endorse or promote products derived from this software
+  *      without specific prior written permission.
+  *
+  * THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS "AS IS"
+  * AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE
+  * IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE
+  * DISCLAIMED. IN NO EVENT SHALL THE COPYRIGHT HOLDER OR CONTRIBUTORS BE LIABLE
+  * FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL
+  * DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR
+  * SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER
+  * CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY,
+  * OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE
+  * OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.
+  *
+  ******************************************************************************
+  */
+/* USER CODE END Header */
+
+/* Define to prevent recursive inclusion -------------------------------------*/
+#ifndef __MAIN_H
+#define __MAIN_H
+
+#ifdef __cplusplus
+extern "C" {
+#endif
+
+/* Includes ------------------------------------------------------------------*/
+#include "stm32f7xx_hal.h"
+
+/* Private includes ----------------------------------------------------------*/
+/* USER CODE BEGIN Includes */
+
+/* USER CODE END Includes */
+
+/* Exported types ------------------------------------------------------------*/
+/* USER CODE BEGIN ET */
+
+/* USER CODE END ET */
+
+/* Exported constants --------------------------------------------------------*/
+/* USER CODE BEGIN EC */
+
+/* USER CODE END EC */
+
+/* Exported macro ------------------------------------------------------------*/
+/* USER CODE BEGIN EM */
+
+/* USER CODE END EM */
+
+/* Exported functions prototypes ---------------------------------------------*/
+void Error_Handler(void);
+
+/* USER CODE BEGIN EFP */
+
+/* USER CODE END EFP */
+
+/* Private defines -----------------------------------------------------------*/
+#define USER_Btn_Pin GPIO_PIN_13
+#define USER_Btn_GPIO_Port GPIOC
+#define MCO_Pin GPIO_PIN_0
+#define MCO_GPIO_Port GPIOH
+#define RMII_MDC_Pin GPIO_PIN_1
+#define RMII_MDC_GPIO_Port GPIOC
+#define RMII_REF_CLK_Pin GPIO_PIN_1
+#define RMII_REF_CLK_GPIO_Port GPIOA
+#define RMII_MDIO_Pin GPIO_PIN_2
+#define RMII_MDIO_GPIO_Port GPIOA
+#define RMII_CRS_DV_Pin GPIO_PIN_7
+#define RMII_CRS_DV_GPIO_Port GPIOA
+#define RMII_RXD0_Pin GPIO_PIN_4
+#define RMII_RXD0_GPIO_Port GPIOC
+#define RMII_RXD1_Pin GPIO_PIN_5
+#define RMII_RXD1_GPIO_Port GPIOC
+#define RMII_TXD1_Pin GPIO_PIN_13
+#define RMII_TXD1_GPIO_Port GPIOB
+#define LD3_Pin GPIO_PIN_14
+#define LD3_GPIO_Port GPIOB
+#define STLK_RX_Pin GPIO_PIN_8
+#define STLK_RX_GPIO_Port GPIOD
+#define STLK_TX_Pin GPIO_PIN_9
+#define STLK_TX_GPIO_Port GPIOD
+#define USB_PowerSwitchOn_Pin GPIO_PIN_6
+#define USB_PowerSwitchOn_GPIO_Port GPIOG
+#define USB_OverCurrent_Pin GPIO_PIN_7
+#define USB_OverCurrent_GPIO_Port GPIOG
+#define USB_SOF_Pin GPIO_PIN_8
+#define USB_SOF_GPIO_Port GPIOA
+#define USB_VBUS_Pin GPIO_PIN_9
+#define USB_VBUS_GPIO_Port GPIOA
+#define USB_ID_Pin GPIO_PIN_10
+#define USB_ID_GPIO_Port GPIOA
+#define USB_DM_Pin GPIO_PIN_11
+#define USB_DM_GPIO_Port GPIOA
+#define USB_DP_Pin GPIO_PIN_12
+#define USB_DP_GPIO_Port GPIOA
+#define TMS_Pin GPIO_PIN_13
+#define TMS_GPIO_Port GPIOA
+#define TCK_Pin GPIO_PIN_14
+#define TCK_GPIO_Port GPIOA
+#define RMII_TX_EN_Pin GPIO_PIN_11
+#define RMII_TX_EN_GPIO_Port GPIOG
+#define RMII_TXD0_Pin GPIO_PIN_13
+#define RMII_TXD0_GPIO_Port GPIOG
+#define SWO_Pin GPIO_PIN_3
+#define SWO_GPIO_Port GPIOB
+#define LD2_Pin GPIO_PIN_7
+#define LD2_GPIO_Port GPIOB
+/* USER CODE BEGIN Private defines */
+
+/* USER CODE END Private defines */
+
+#ifdef __cplusplus
+}
+#endif
+
+#endif /* __MAIN_H */
+
+/************************ (C) COPYRIGHT STMicroelectronics *****END OF FILE****/

bsp/stm32/stm32f767-st-nucleo/board/CubeMX_Config/Inc/stm32f7xx_hal_conf.h

@@ -0,0 +1,458 @@
+/**
+  ******************************************************************************
+  * @file    stm32f7xx_hal_conf.h
+  * @brief   HAL configuration file.
+  ******************************************************************************
+  * @attention
+  *
+  * <h2><center>&copy; COPYRIGHT(c) 2019 STMicroelectronics</center></h2>
+  *
+  * Redistribution and use in source and binary forms, with or without modification,
+  * are permitted provided that the following conditions are met:
+  *   1. Redistributions of source code must retain the above copyright notice,
+  *      this list of conditions and the following disclaimer.
+  *   2. Redistributions in binary form must reproduce the above copyright notice,
+  *      this list of conditions and the following disclaimer in the documentation
+  *      and/or other materials provided with the distribution.
+  *   3. Neither the name of STMicroelectronics nor the names of its contributors
+  *      may be used to endorse or promote products derived from this software
+  *      without specific prior written permission.
+  *
+  * THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS "AS IS"
+  * AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE
+  * IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE
+  * DISCLAIMED. IN NO EVENT SHALL THE COPYRIGHT HOLDER OR CONTRIBUTORS BE LIABLE
+  * FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL
+  * DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR
+  * SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER
+  * CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY,
+  * OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE
+  * OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.
+  *
+  ******************************************************************************
+  */ 
+
+/* Define to prevent recursive inclusion -------------------------------------*/
+#ifndef __STM32F7xx_HAL_CONF_H
+#define __STM32F7xx_HAL_CONF_H
+
+#ifdef __cplusplus
+ extern "C" {
+#endif
+
+/* Exported types ------------------------------------------------------------*/
+/* Exported constants --------------------------------------------------------*/
+
+/* ########################## Module Selection ############################## */
+/**
+  * @brief This is the list of modules to be used in the HAL driver 
+  */
+#define HAL_MODULE_ENABLED  
+
+/* #define HAL_ADC_MODULE_ENABLED   */
+/* #define HAL_CRYP_MODULE_ENABLED   */
+/* #define HAL_CAN_MODULE_ENABLED   */
+/* #define HAL_CEC_MODULE_ENABLED   */
+/* #define HAL_CRC_MODULE_ENABLED   */
+/* #define HAL_CRYP_MODULE_ENABLED   */
+/* #define HAL_DAC_MODULE_ENABLED   */
+/* #define HAL_DCMI_MODULE_ENABLED   */
+/* #define HAL_DMA2D_MODULE_ENABLED   */
+#define HAL_ETH_MODULE_ENABLED
+/* #define HAL_NAND_MODULE_ENABLED   */
+/* #define HAL_NOR_MODULE_ENABLED   */
+/* #define HAL_SRAM_MODULE_ENABLED   */
+/* #define HAL_SDRAM_MODULE_ENABLED   */
+/* #define HAL_HASH_MODULE_ENABLED   */
+/* #define HAL_I2S_MODULE_ENABLED   */
+/* #define HAL_IWDG_MODULE_ENABLED   */
+/* #define HAL_LPTIM_MODULE_ENABLED   */
+/* #define HAL_LTDC_MODULE_ENABLED   */
+/* #define HAL_QSPI_MODULE_ENABLED   */
+/* #define HAL_RNG_MODULE_ENABLED   */
+/* #define HAL_RTC_MODULE_ENABLED   */
+/* #define HAL_SAI_MODULE_ENABLED   */
+/* #define HAL_SD_MODULE_ENABLED   */
+/* #define HAL_MMC_MODULE_ENABLED   */
+/* #define HAL_SPDIFRX_MODULE_ENABLED   */
+/* #define HAL_SPI_MODULE_ENABLED   */
+/* #define HAL_TIM_MODULE_ENABLED   */
+#define HAL_UART_MODULE_ENABLED
+/* #define HAL_USART_MODULE_ENABLED   */
+/* #define HAL_IRDA_MODULE_ENABLED   */
+/* #define HAL_SMARTCARD_MODULE_ENABLED   */
+/* #define HAL_WWDG_MODULE_ENABLED   */
+#define HAL_PCD_MODULE_ENABLED
+/* #define HAL_HCD_MODULE_ENABLED   */
+/* #define HAL_DFSDM_MODULE_ENABLED   */
+/* #define HAL_DSI_MODULE_ENABLED   */
+/* #define HAL_JPEG_MODULE_ENABLED   */
+/* #define HAL_MDIOS_MODULE_ENABLED   */
+/* #define HAL_SMBUS_MODULE_ENABLED   */
+/* #define HAL_MMC_MODULE_ENABLED   */
+/* #define HAL_EXTI_MODULE_ENABLED   */
+#define HAL_GPIO_MODULE_ENABLED
+#define HAL_DMA_MODULE_ENABLED
+#define HAL_RCC_MODULE_ENABLED
+#define HAL_FLASH_MODULE_ENABLED
+#define HAL_PWR_MODULE_ENABLED
+#define HAL_I2C_MODULE_ENABLED
+#define HAL_CORTEX_MODULE_ENABLED
+
+/* ########################## HSE/HSI Values adaptation ##################### */
+/**
+  * @brief Adjust the value of External High Speed oscillator (HSE) used in your application.
+  *        This value is used by the RCC HAL module to compute the system frequency
+  *        (when HSE is used as system clock source, directly or through the PLL).  
+  */
+#if !defined  (HSE_VALUE) 
+  #define HSE_VALUE    ((uint32_t)8000000U) /*!< Value of the External oscillator in Hz */
+#endif /* HSE_VALUE */
+
+#if !defined  (HSE_STARTUP_TIMEOUT)
+  #define HSE_STARTUP_TIMEOUT    ((uint32_t)100U)   /*!< Time out for HSE start up, in ms */
+#endif /* HSE_STARTUP_TIMEOUT */
+
+/**
+  * @brief Internal High Speed oscillator (HSI) value.
+  *        This value is used by the RCC HAL module to compute the system frequency
+  *        (when HSI is used as system clock source, directly or through the PLL). 
+  */
+#if !defined  (HSI_VALUE)
+  #define HSI_VALUE    ((uint32_t)16000000U) /*!< Value of the Internal oscillator in Hz*/
+#endif /* HSI_VALUE */
+
+/**
+  * @brief Internal Low Speed oscillator (LSI) value.
+  */
+#if !defined  (LSI_VALUE) 
+ #define LSI_VALUE  ((uint32_t)32000U)       /*!< LSI Typical Value in Hz*/
+#endif /* LSI_VALUE */                      /*!< Value of the Internal Low Speed oscillator in Hz
+                                             The real value may vary depending on the variations
+                                             in voltage and temperature.  */
+/**
+  * @brief External Low Speed oscillator (LSE) value.
+  */
+#if !defined  (LSE_VALUE)
+ #define LSE_VALUE  ((uint32_t)32768U)    /*!< Value of the External Low Speed oscillator in Hz */
+#endif /* LSE_VALUE */
+
+#if !defined  (LSE_STARTUP_TIMEOUT)
+  #define LSE_STARTUP_TIMEOUT    ((uint32_t)5000U)   /*!< Time out for LSE start up, in ms */
+#endif /* LSE_STARTUP_TIMEOUT */
+
+/**
+  * @brief External clock source for I2S peripheral
+  *        This value is used by the I2S HAL module to compute the I2S clock source 
+  *        frequency, this source is inserted directly through I2S_CKIN pad. 
+  */
+#if !defined  (EXTERNAL_CLOCK_VALUE)
+  #define EXTERNAL_CLOCK_VALUE    ((uint32_t)12288000U) /*!< Value of the Internal oscillator in Hz*/
+#endif /* EXTERNAL_CLOCK_VALUE */
+
+/* Tip: To avoid modifying this file each time you need to use different HSE,
+   ===  you can define the HSE value in your toolchain compiler preprocessor. */
+
+/* ########################### System Configuration ######################### */
+/**
+  * @brief This is the HAL system configuration section
+  */     
+#define  VDD_VALUE                    ((uint32_t)3300U) /*!< Value of VDD in mv */
+#define  TICK_INT_PRIORITY            ((uint32_t)0U) /*!< tick interrupt priority */
+#define  USE_RTOS                     0U
+#define  PREFETCH_ENABLE              0U
+#define  ART_ACCLERATOR_ENABLE        0U /* To enable instruction cache and prefetch */
+
+/* ########################## Assert Selection ############################## */
+/**
+  * @brief Uncomment the line below to expanse the "assert_param" macro in the 
+  *        HAL drivers code
+  */
+/* #define USE_FULL_ASSERT    1U */
+
+/* ################## Ethernet peripheral configuration ##################### */
+
+/* Section 1 : Ethernet peripheral configuration */
+
+/* MAC ADDRESS: MAC_ADDR0:MAC_ADDR1:MAC_ADDR2:MAC_ADDR3:MAC_ADDR4:MAC_ADDR5 */
+#define MAC_ADDR0   2U
+#define MAC_ADDR1   0U
+#define MAC_ADDR2   0U
+#define MAC_ADDR3   0U
+#define MAC_ADDR4   0U
+#define MAC_ADDR5   0U
+
+/* Definition of the Ethernet driver buffers size and count */   
+#define ETH_RX_BUF_SIZE                ETH_MAX_PACKET_SIZE /* buffer size for receive               */
+#define ETH_TX_BUF_SIZE                ETH_MAX_PACKET_SIZE /* buffer size for transmit              */
+#define ETH_RXBUFNB                    ((uint32_t)4U)       /* 4 Rx buffers of size ETH_RX_BUF_SIZE  */
+#define ETH_TXBUFNB                    ((uint32_t)4U)       /* 4 Tx buffers of size ETH_TX_BUF_SIZE  */
+
+/* Section 2: PHY configuration section */
+
+/* LAN8742A_PHY_ADDRESS Address*/ 
+#define LAN8742A_PHY_ADDRESS           0
+/* PHY Reset delay these values are based on a 1 ms Systick interrupt*/ 
+#define PHY_RESET_DELAY                 ((uint32_t)0x000000FFU)
+/* PHY Configuration delay */
+#define PHY_CONFIG_DELAY                ((uint32_t)0x00000FFFU)
+
+#define PHY_READ_TO                     ((uint32_t)0x0000FFFFU)
+#define PHY_WRITE_TO                    ((uint32_t)0x0000FFFFU)
+
+/* Section 3: Common PHY Registers */
+
+#define PHY_BCR                         ((uint16_t)0x00U)    /*!< Transceiver Basic Control Register   */
+#define PHY_BSR                         ((uint16_t)0x01U)    /*!< Transceiver Basic Status Register    */
+ 
+#define PHY_RESET                       ((uint16_t)0x8000U)  /*!< PHY Reset */
+#define PHY_LOOPBACK                    ((uint16_t)0x4000U)  /*!< Select loop-back mode */
+#define PHY_FULLDUPLEX_100M             ((uint16_t)0x2100U)  /*!< Set the full-duplex mode at 100 Mb/s */
+#define PHY_HALFDUPLEX_100M             ((uint16_t)0x2000U)  /*!< Set the half-duplex mode at 100 Mb/s */
+#define PHY_FULLDUPLEX_10M              ((uint16_t)0x0100U)  /*!< Set the full-duplex mode at 10 Mb/s  */
+#define PHY_HALFDUPLEX_10M              ((uint16_t)0x0000U)  /*!< Set the half-duplex mode at 10 Mb/s  */
+#define PHY_AUTONEGOTIATION             ((uint16_t)0x1000U)  /*!< Enable auto-negotiation function     */
+#define PHY_RESTART_AUTONEGOTIATION     ((uint16_t)0x0200U)  /*!< Restart auto-negotiation function    */
+#define PHY_POWERDOWN                   ((uint16_t)0x0800U)  /*!< Select the power down mode           */
+#define PHY_ISOLATE                     ((uint16_t)0x0400U)  /*!< Isolate PHY from MII                 */
+
+#define PHY_AUTONEGO_COMPLETE           ((uint16_t)0x0020U)  /*!< Auto-Negotiation process completed   */
+#define PHY_LINKED_STATUS               ((uint16_t)0x0004U)  /*!< Valid link established               */
+#define PHY_JABBER_DETECTION            ((uint16_t)0x0002U)  /*!< Jabber condition detected            */
+  
+/* Section 4: Extended PHY Registers */
+#define PHY_SR                          ((uint16_t)0x10U)    /*!< PHY status register Offset                      */
+
+#define PHY_SPEED_STATUS                ((uint16_t)0x0002U)  /*!< PHY Speed mask                                  */
+#define PHY_DUPLEX_STATUS               ((uint16_t)0x0004U)  /*!< PHY Duplex mask                                 */
+
+#define PHY_ISFR                        ((uint16_t)0x000BU)    /*!< PHY Interrupt Source Flag register Offset   */
+#define PHY_ISFR_INT4                   ((uint16_t)0x000BU)  /*!< PHY Link down inturrupt       */  
+
+/* ################## SPI peripheral configuration ########################## */
+
+/* CRC FEATURE: Use to activate CRC feature inside HAL SPI Driver
+* Activated: CRC code is present inside driver
+* Deactivated: CRC code cleaned from driver
+*/
+
+#define USE_SPI_CRC                     0U
+
+/* Includes ------------------------------------------------------------------*/
+/**
+  * @brief Include module's header file 
+  */
+
+#ifdef HAL_RCC_MODULE_ENABLED
+  #include "stm32f7xx_hal_rcc.h"
+#endif /* HAL_RCC_MODULE_ENABLED */
+
+#ifdef HAL_EXTI_MODULE_ENABLED
+  #include "stm32f7xx_hal_exti.h"
+#endif /* HAL_EXTI_MODULE_ENABLED */
+
+#ifdef HAL_GPIO_MODULE_ENABLED
+  #include "stm32f7xx_hal_gpio.h"
+#endif /* HAL_GPIO_MODULE_ENABLED */
+
+#ifdef HAL_DMA_MODULE_ENABLED
+  #include "stm32f7xx_hal_dma.h"
+#endif /* HAL_DMA_MODULE_ENABLED */
+   
+#ifdef HAL_CORTEX_MODULE_ENABLED
+  #include "stm32f7xx_hal_cortex.h"
+#endif /* HAL_CORTEX_MODULE_ENABLED */
+
+#ifdef HAL_ADC_MODULE_ENABLED
+  #include "stm32f7xx_hal_adc.h"
+#endif /* HAL_ADC_MODULE_ENABLED */
+
+#ifdef HAL_CAN_MODULE_ENABLED
+  #include "stm32f7xx_hal_can.h"
+#endif /* HAL_CAN_MODULE_ENABLED */
+
+#ifdef HAL_CEC_MODULE_ENABLED
+  #include "stm32f7xx_hal_cec.h"
+#endif /* HAL_CEC_MODULE_ENABLED */
+
+#ifdef HAL_CRC_MODULE_ENABLED
+  #include "stm32f7xx_hal_crc.h"
+#endif /* HAL_CRC_MODULE_ENABLED */
+
+#ifdef HAL_CRYP_MODULE_ENABLED
+  #include "stm32f7xx_hal_cryp.h" 
+#endif /* HAL_CRYP_MODULE_ENABLED */
+
+#ifdef HAL_DMA2D_MODULE_ENABLED
+  #include "stm32f7xx_hal_dma2d.h"
+#endif /* HAL_DMA2D_MODULE_ENABLED */
+
+#ifdef HAL_DAC_MODULE_ENABLED
+  #include "stm32f7xx_hal_dac.h"
+#endif /* HAL_DAC_MODULE_ENABLED */
+
+#ifdef HAL_DCMI_MODULE_ENABLED
+  #include "stm32f7xx_hal_dcmi.h"
+#endif /* HAL_DCMI_MODULE_ENABLED */
+
+#ifdef HAL_ETH_MODULE_ENABLED
+  #include "stm32f7xx_hal_eth.h"
+#endif /* HAL_ETH_MODULE_ENABLED */
+
+#ifdef HAL_FLASH_MODULE_ENABLED
+  #include "stm32f7xx_hal_flash.h"
+#endif /* HAL_FLASH_MODULE_ENABLED */
+ 
+#ifdef HAL_SRAM_MODULE_ENABLED
+  #include "stm32f7xx_hal_sram.h"
+#endif /* HAL_SRAM_MODULE_ENABLED */
+
+#ifdef HAL_NOR_MODULE_ENABLED
+  #include "stm32f7xx_hal_nor.h"
+#endif /* HAL_NOR_MODULE_ENABLED */
+
+#ifdef HAL_NAND_MODULE_ENABLED
+  #include "stm32f7xx_hal_nand.h"
+#endif /* HAL_NAND_MODULE_ENABLED */
+
+#ifdef HAL_SDRAM_MODULE_ENABLED
+  #include "stm32f7xx_hal_sdram.h"
+#endif /* HAL_SDRAM_MODULE_ENABLED */      
+
+#ifdef HAL_HASH_MODULE_ENABLED
+ #include "stm32f7xx_hal_hash.h"
+#endif /* HAL_HASH_MODULE_ENABLED */
+
+#ifdef HAL_I2C_MODULE_ENABLED
+ #include "stm32f7xx_hal_i2c.h"
+#endif /* HAL_I2C_MODULE_ENABLED */
+
+#ifdef HAL_I2S_MODULE_ENABLED
+ #include "stm32f7xx_hal_i2s.h"
+#endif /* HAL_I2S_MODULE_ENABLED */
+
+#ifdef HAL_IWDG_MODULE_ENABLED
+ #include "stm32f7xx_hal_iwdg.h"
+#endif /* HAL_IWDG_MODULE_ENABLED */
+
+#ifdef HAL_LPTIM_MODULE_ENABLED
+ #include "stm32f7xx_hal_lptim.h"
+#endif /* HAL_LPTIM_MODULE_ENABLED */
+
+#ifdef HAL_LTDC_MODULE_ENABLED
+ #include "stm32f7xx_hal_ltdc.h"
+#endif /* HAL_LTDC_MODULE_ENABLED */
+
+#ifdef HAL_PWR_MODULE_ENABLED
+ #include "stm32f7xx_hal_pwr.h"
+#endif /* HAL_PWR_MODULE_ENABLED */
+
+#ifdef HAL_QSPI_MODULE_ENABLED
+ #include "stm32f7xx_hal_qspi.h"
+#endif /* HAL_QSPI_MODULE_ENABLED */
+
+#ifdef HAL_RNG_MODULE_ENABLED
+ #include "stm32f7xx_hal_rng.h"
+#endif /* HAL_RNG_MODULE_ENABLED */
+
+#ifdef HAL_RTC_MODULE_ENABLED
+ #include "stm32f7xx_hal_rtc.h"
+#endif /* HAL_RTC_MODULE_ENABLED */
+
+#ifdef HAL_SAI_MODULE_ENABLED
+ #include "stm32f7xx_hal_sai.h"
+#endif /* HAL_SAI_MODULE_ENABLED */
+
+#ifdef HAL_SD_MODULE_ENABLED
+ #include "stm32f7xx_hal_sd.h"
+#endif /* HAL_SD_MODULE_ENABLED */
+
+#ifdef HAL_MMC_MODULE_ENABLED
+ #include "stm32f7xx_hal_mmc.h"
+#endif /* HAL_MMC_MODULE_ENABLED */
+
+#ifdef HAL_SPDIFRX_MODULE_ENABLED
+ #include "stm32f7xx_hal_spdifrx.h"
+#endif /* HAL_SPDIFRX_MODULE_ENABLED */
+
+#ifdef HAL_SPI_MODULE_ENABLED
+ #include "stm32f7xx_hal_spi.h"
+#endif /* HAL_SPI_MODULE_ENABLED */
+
+#ifdef HAL_TIM_MODULE_ENABLED
+ #include "stm32f7xx_hal_tim.h"
+#endif /* HAL_TIM_MODULE_ENABLED */
+
+#ifdef HAL_UART_MODULE_ENABLED
+ #include "stm32f7xx_hal_uart.h"
+#endif /* HAL_UART_MODULE_ENABLED */
+
+#ifdef HAL_USART_MODULE_ENABLED
+ #include "stm32f7xx_hal_usart.h"
+#endif /* HAL_USART_MODULE_ENABLED */
+
+#ifdef HAL_IRDA_MODULE_ENABLED
+ #include "stm32f7xx_hal_irda.h"
+#endif /* HAL_IRDA_MODULE_ENABLED */
+
+#ifdef HAL_SMARTCARD_MODULE_ENABLED
+ #include "stm32f7xx_hal_smartcard.h"
+#endif /* HAL_SMARTCARD_MODULE_ENABLED */
+
+#ifdef HAL_WWDG_MODULE_ENABLED
+ #include "stm32f7xx_hal_wwdg.h"
+#endif /* HAL_WWDG_MODULE_ENABLED */
+
+#ifdef HAL_PCD_MODULE_ENABLED
+ #include "stm32f7xx_hal_pcd.h"
+#endif /* HAL_PCD_MODULE_ENABLED */
+
+#ifdef HAL_HCD_MODULE_ENABLED
+ #include "stm32f7xx_hal_hcd.h"
+#endif /* HAL_HCD_MODULE_ENABLED */
+
+#ifdef HAL_DFSDM_MODULE_ENABLED
+ #include "stm32f7xx_hal_dfsdm.h"
+#endif /* HAL_DFSDM_MODULE_ENABLED */
+
+#ifdef HAL_DSI_MODULE_ENABLED
+ #include "stm32f7xx_hal_dsi.h"
+#endif /* HAL_DSI_MODULE_ENABLED */
+
+#ifdef HAL_JPEG_MODULE_ENABLED
+ #include "stm32f7xx_hal_jpeg.h"
+#endif /* HAL_JPEG_MODULE_ENABLED */
+
+#ifdef HAL_MDIOS_MODULE_ENABLED
+ #include "stm32f7xx_hal_mdios.h"
+#endif /* HAL_MDIOS_MODULE_ENABLED */   
+
+#ifdef HAL_SMBUS_MODULE_ENABLED
+ #include "stm32f7xx_hal_smbus.h"
+#endif /* HAL_SMBUS_MODULE_ENABLED */
+
+/* Exported macro ------------------------------------------------------------*/
+#ifdef  USE_FULL_ASSERT
+/**
+  * @brief  The assert_param macro is used for function's parameters check.
+  * @param  expr: If expr is false, it calls assert_failed function
+  *         which reports the name of the source file and the source
+  *         line number of the call that failed. 
+  *         If expr is true, it returns no value.
+  * @retval None
+  */
+  #define assert_param(expr) ((expr) ? (void)0U : assert_failed((uint8_t *)__FILE__, __LINE__))
+/* Exported functions ------------------------------------------------------- */
+  void assert_failed(uint8_t* file, uint32_t line);
+#else
+  #define assert_param(expr) ((void)0U)
+#endif /* USE_FULL_ASSERT */
+
+#ifdef __cplusplus
+}
+#endif
+
+#endif /* __STM32F7xx_HAL_CONF_H */
+ 
+
+/************************ (C) COPYRIGHT STMicroelectronics *****END OF FILE****/

bsp/stm32/stm32f767-st-nucleo/board/CubeMX_Config/Inc/stm32f7xx_it.h

@@ -0,0 +1,84 @@
+/* USER CODE BEGIN Header */
+/**
+  ******************************************************************************
+  * @file    stm32f7xx_it.h
+  * @brief   This file contains the headers of the interrupt handlers.
+  ******************************************************************************
+  *
+  * COPYRIGHT(c) 2018 STMicroelectronics
+  *
+  * Redistribution and use in source and binary forms, with or without modification,
+  * are permitted provided that the following conditions are met:
+  *   1. Redistributions of source code must retain the above copyright notice,
+  *      this list of conditions and the following disclaimer.
+  *   2. Redistributions in binary form must reproduce the above copyright notice,
+  *      this list of conditions and the following disclaimer in the documentation
+  *      and/or other materials provided with the distribution.
+  *   3. Neither the name of STMicroelectronics nor the names of its contributors
+  *      may be used to endorse or promote products derived from this software
+  *      without specific prior written permission.
+  *
+  * THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS "AS IS"
+  * AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE
+  * IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE
+  * DISCLAIMED. IN NO EVENT SHALL THE COPYRIGHT HOLDER OR CONTRIBUTORS BE LIABLE
+  * FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL
+  * DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR
+  * SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER
+  * CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY,
+  * OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE
+  * OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.
+  *
+  ******************************************************************************
+  */
+/* USER CODE END Header */
+
+/* Define to prevent recursive inclusion -------------------------------------*/
+#ifndef __STM32F7xx_IT_H
+#define __STM32F7xx_IT_H
+
+#ifdef __cplusplus
+ extern "C" {
+#endif 
+
+/* Private includes ----------------------------------------------------------*/
+/* USER CODE BEGIN Includes */
+
+/* USER CODE END Includes */
+
+/* Exported types ------------------------------------------------------------*/
+/* USER CODE BEGIN ET */
+
+/* USER CODE END ET */
+
+/* Exported constants --------------------------------------------------------*/
+/* USER CODE BEGIN EC */
+
+/* USER CODE END EC */
+
+/* Exported macro ------------------------------------------------------------*/
+/* USER CODE BEGIN EM */
+
+/* USER CODE END EM */
+
+/* Exported functions prototypes ---------------------------------------------*/
+void NMI_Handler(void);
+void HardFault_Handler(void);
+void MemManage_Handler(void);
+void BusFault_Handler(void);
+void UsageFault_Handler(void);
+void SVC_Handler(void);
+void DebugMon_Handler(void);
+void PendSV_Handler(void);
+void SysTick_Handler(void);
+/* USER CODE BEGIN EFP */
+
+/* USER CODE END EFP */
+
+#ifdef __cplusplus
+}
+#endif
+
+#endif /* __STM32F7xx_IT_H */
+
+/************************ (C) COPYRIGHT STMicroelectronics *****END OF FILE****/

bsp/stm32/stm32f767-st-nucleo/board/CubeMX_Config/Src/main.c

@@ -0,0 +1,396 @@
+/* USER CODE BEGIN Header */
+/**
+  ******************************************************************************
+  * @file           : main.c
+  * @brief          : Main program body
+  ******************************************************************************
+  ** This notice applies to any and all portions of this file
+  * that are not between comment pairs USER CODE BEGIN and
+  * USER CODE END. Other portions of this file, whether 
+  * inserted by the user or by software development tools
+  * are owned by their respective copyright owners.
+  *
+  * COPYRIGHT(c) 2018 STMicroelectronics
+  *
+  * Redistribution and use in source and binary forms, with or without modification,
+  * are permitted provided that the following conditions are met:
+  *   1. Redistributions of source code must retain the above copyright notice,
+  *      this list of conditions and the following disclaimer.
+  *   2. Redistributions in binary form must reproduce the above copyright notice,
+  *      this list of conditions and the following disclaimer in the documentation
+  *      and/or other materials provided with the distribution.
+  *   3. Neither the name of STMicroelectronics nor the names of its contributors
+  *      may be used to endorse or promote products derived from this software
+  *      without specific prior written permission.
+  *
+  * THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS "AS IS"
+  * AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE
+  * IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE
+  * DISCLAIMED. IN NO EVENT SHALL THE COPYRIGHT HOLDER OR CONTRIBUTORS BE LIABLE
+  * FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL
+  * DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR
+  * SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER
+  * CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY,
+  * OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE
+  * OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.
+  *
+  ******************************************************************************
+  */
+/* USER CODE END Header */
+
+/* Includes ------------------------------------------------------------------*/
+#include "main.h"
+
+/* Private includes ----------------------------------------------------------*/
+/* USER CODE BEGIN Includes */
+
+/* USER CODE END Includes */
+
+/* Private typedef -----------------------------------------------------------*/
+/* USER CODE BEGIN PTD */
+
+/* USER CODE END PTD */
+
+/* Private define ------------------------------------------------------------*/
+/* USER CODE BEGIN PD */
+
+/* USER CODE END PD */
+
+/* Private macro -------------------------------------------------------------*/
+/* USER CODE BEGIN PM */
+
+/* USER CODE END PM */
+
+/* Private variables ---------------------------------------------------------*/
+
+ETH_HandleTypeDef heth;
+
+UART_HandleTypeDef huart3;
+
+PCD_HandleTypeDef hpcd_USB_OTG_FS;
+
+/* USER CODE BEGIN PV */
+
+/* USER CODE END PV */
+
+/* Private function prototypes -----------------------------------------------*/
+void SystemClock_Config(void);
+static void MX_GPIO_Init(void);
+static void MX_ETH_Init(void);
+static void MX_USART3_UART_Init(void);
+static void MX_USB_OTG_FS_PCD_Init(void);
+/* USER CODE BEGIN PFP */
+
+/* USER CODE END PFP */
+
+/* Private user code ---------------------------------------------------------*/
+/* USER CODE BEGIN 0 */
+
+/* USER CODE END 0 */
+
+/**
+  * @brief  The application entry point.
+  * @retval int
+  */
+int main(void)
+{
+  /* USER CODE BEGIN 1 */
+
+  /* USER CODE END 1 */
+
+  /* MCU Configuration--------------------------------------------------------*/
+
+  /* Reset of all peripherals, Initializes the Flash interface and the Systick. */
+  HAL_Init();
+
+  /* USER CODE BEGIN Init */
+
+  /* USER CODE END Init */
+
+  /* Configure the system clock */
+  SystemClock_Config();
+
+  /* USER CODE BEGIN SysInit */
+
+  /* USER CODE END SysInit */
+
+  /* Initialize all configured peripherals */
+  MX_GPIO_Init();
+  MX_ETH_Init();
+  MX_USART3_UART_Init();
+  MX_USB_OTG_FS_PCD_Init();
+  /* USER CODE BEGIN 2 */
+
+  /* USER CODE END 2 */
+
+  /* Infinite loop */
+  /* USER CODE BEGIN WHILE */
+  while (1)
+  {
+    /* USER CODE END WHILE */
+
+    /* USER CODE BEGIN 3 */
+  }
+  /* USER CODE END 3 */
+}
+
+/**
+  * @brief System Clock Configuration
+  * @retval None
+  */
+void SystemClock_Config(void)
+{
+  RCC_OscInitTypeDef RCC_OscInitStruct = {0};
+  RCC_ClkInitTypeDef RCC_ClkInitStruct = {0};
+  RCC_PeriphCLKInitTypeDef PeriphClkInitStruct = {0};
+
+  /**Configure LSE Drive Capability 
+  */
+  HAL_PWR_EnableBkUpAccess();
+  /**Configure the main internal regulator output voltage 
+  */
+  __HAL_RCC_PWR_CLK_ENABLE();
+  __HAL_PWR_VOLTAGESCALING_CONFIG(PWR_REGULATOR_VOLTAGE_SCALE1);
+  /**Initializes the CPU, AHB and APB busses clocks 
+  */
+  RCC_OscInitStruct.OscillatorType = RCC_OSCILLATORTYPE_HSE;
+  RCC_OscInitStruct.HSEState = RCC_HSE_BYPASS;
+  RCC_OscInitStruct.PLL.PLLState = RCC_PLL_ON;
+  RCC_OscInitStruct.PLL.PLLSource = RCC_PLLSOURCE_HSE;
+  RCC_OscInitStruct.PLL.PLLM = 8;
+  RCC_OscInitStruct.PLL.PLLN = 432;
+  RCC_OscInitStruct.PLL.PLLP = RCC_PLLP_DIV2;
+  RCC_OscInitStruct.PLL.PLLQ = 9;
+  if (HAL_RCC_OscConfig(&RCC_OscInitStruct) != HAL_OK)
+  {
+    Error_Handler();
+  }
+  /**Activate the Over-Drive mode 
+  */
+  if (HAL_PWREx_EnableOverDrive() != HAL_OK)
+  {
+    Error_Handler();
+  }
+  /**Initializes the CPU, AHB and APB busses clocks 
+  */
+  RCC_ClkInitStruct.ClockType = RCC_CLOCKTYPE_HCLK|RCC_CLOCKTYPE_SYSCLK
+                              |RCC_CLOCKTYPE_PCLK1|RCC_CLOCKTYPE_PCLK2;
+  RCC_ClkInitStruct.SYSCLKSource = RCC_SYSCLKSOURCE_PLLCLK;
+  RCC_ClkInitStruct.AHBCLKDivider = RCC_SYSCLK_DIV1;
+  RCC_ClkInitStruct.APB1CLKDivider = RCC_HCLK_DIV4;
+  RCC_ClkInitStruct.APB2CLKDivider = RCC_HCLK_DIV2;
+
+  if (HAL_RCC_ClockConfig(&RCC_ClkInitStruct, FLASH_LATENCY_7) != HAL_OK)
+  {
+    Error_Handler();
+  }
+  PeriphClkInitStruct.PeriphClockSelection = RCC_PERIPHCLK_USART3|RCC_PERIPHCLK_CLK48;
+  PeriphClkInitStruct.Usart3ClockSelection = RCC_USART3CLKSOURCE_PCLK1;
+  PeriphClkInitStruct.Clk48ClockSelection = RCC_CLK48SOURCE_PLL;
+  if (HAL_RCCEx_PeriphCLKConfig(&PeriphClkInitStruct) != HAL_OK)
+  {
+    Error_Handler();
+  }
+}
+
+/**
+  * @brief ETH Initialization Function
+  * @param None
+  * @retval None
+  */
+static void MX_ETH_Init(void)
+{
+
+  /* USER CODE BEGIN ETH_Init 0 */
+
+  /* USER CODE END ETH_Init 0 */
+
+   uint8_t MACAddr[6] ;
+
+  /* USER CODE BEGIN ETH_Init 1 */
+
+  /* USER CODE END ETH_Init 1 */
+  heth.Instance = ETH;
+  heth.Init.AutoNegotiation = ETH_AUTONEGOTIATION_ENABLE;
+  heth.Init.PhyAddress = LAN8742A_PHY_ADDRESS;
+  MACAddr[0] = 0x00;
+  MACAddr[1] = 0x80;
+  MACAddr[2] = 0xE1;
+  MACAddr[3] = 0x00;
+  MACAddr[4] = 0x00;
+  MACAddr[5] = 0x00;
+  heth.Init.MACAddr = &MACAddr[0];
+  heth.Init.RxMode = ETH_RXPOLLING_MODE;
+  heth.Init.ChecksumMode = ETH_CHECKSUM_BY_HARDWARE;
+  heth.Init.MediaInterface = ETH_MEDIA_INTERFACE_RMII;
+
+  /* USER CODE BEGIN MACADDRESS */
+    
+  /* USER CODE END MACADDRESS */
+
+  if (HAL_ETH_Init(&heth) != HAL_OK)
+  {
+    Error_Handler();
+  }
+  /* USER CODE BEGIN ETH_Init 2 */
+
+  /* USER CODE END ETH_Init 2 */
+
+}
+
+/**
+  * @brief USART3 Initialization Function
+  * @param None
+  * @retval None
+  */
+static void MX_USART3_UART_Init(void)
+{
+
+  /* USER CODE BEGIN USART3_Init 0 */
+
+  /* USER CODE END USART3_Init 0 */
+
+  /* USER CODE BEGIN USART3_Init 1 */
+
+  /* USER CODE END USART3_Init 1 */
+  huart3.Instance = USART3;
+  huart3.Init.BaudRate = 115200;
+  huart3.Init.WordLength = UART_WORDLENGTH_8B;
+  huart3.Init.StopBits = UART_STOPBITS_1;
+  huart3.Init.Parity = UART_PARITY_NONE;
+  huart3.Init.Mode = UART_MODE_TX_RX;
+  huart3.Init.HwFlowCtl = UART_HWCONTROL_NONE;
+  huart3.Init.OverSampling = UART_OVERSAMPLING_16;
+  huart3.Init.OneBitSampling = UART_ONE_BIT_SAMPLE_DISABLE;
+  huart3.AdvancedInit.AdvFeatureInit = UART_ADVFEATURE_NO_INIT;
+  if (HAL_UART_Init(&huart3) != HAL_OK)
+  {
+    Error_Handler();
+  }
+  /* USER CODE BEGIN USART3_Init 2 */
+
+  /* USER CODE END USART3_Init 2 */
+
+}
+
+/**
+  * @brief USB_OTG_FS Initialization Function
+  * @param None
+  * @retval None
+  */
+static void MX_USB_OTG_FS_PCD_Init(void)
+{
+
+  /* USER CODE BEGIN USB_OTG_FS_Init 0 */
+
+  /* USER CODE END USB_OTG_FS_Init 0 */
+
+  /* USER CODE BEGIN USB_OTG_FS_Init 1 */
+
+  /* USER CODE END USB_OTG_FS_Init 1 */
+  hpcd_USB_OTG_FS.Instance = USB_OTG_FS;
+  hpcd_USB_OTG_FS.Init.dev_endpoints = 6;
+  hpcd_USB_OTG_FS.Init.speed = PCD_SPEED_FULL;
+  hpcd_USB_OTG_FS.Init.dma_enable = DISABLE;
+  hpcd_USB_OTG_FS.Init.ep0_mps = DEP0CTL_MPS_64;
+  hpcd_USB_OTG_FS.Init.phy_itface = PCD_PHY_EMBEDDED;
+  hpcd_USB_OTG_FS.Init.Sof_enable = ENABLE;
+  hpcd_USB_OTG_FS.Init.low_power_enable = DISABLE;
+  hpcd_USB_OTG_FS.Init.lpm_enable = DISABLE;
+  hpcd_USB_OTG_FS.Init.vbus_sensing_enable = ENABLE;
+  hpcd_USB_OTG_FS.Init.use_dedicated_ep1 = DISABLE;
+  if (HAL_PCD_Init(&hpcd_USB_OTG_FS) != HAL_OK)
+  {
+    Error_Handler();
+  }
+  /* USER CODE BEGIN USB_OTG_FS_Init 2 */
+
+  /* USER CODE END USB_OTG_FS_Init 2 */
+
+}
+
+/**
+  * @brief GPIO Initialization Function
+  * @param None
+  * @retval None
+  */
+static void MX_GPIO_Init(void)
+{
+  GPIO_InitTypeDef GPIO_InitStruct = {0};
+
+  /* GPIO Ports Clock Enable */
+  __HAL_RCC_GPIOC_CLK_ENABLE();
+  __HAL_RCC_GPIOH_CLK_ENABLE();
+  __HAL_RCC_GPIOA_CLK_ENABLE();
+  __HAL_RCC_GPIOB_CLK_ENABLE();
+  __HAL_RCC_GPIOD_CLK_ENABLE();
+  __HAL_RCC_GPIOG_CLK_ENABLE();
+
+  /*Configure GPIO pin Output Level */
+  HAL_GPIO_WritePin(GPIOB, LD3_Pin|LD2_Pin, GPIO_PIN_RESET);
+
+  /*Configure GPIO pin Output Level */
+  HAL_GPIO_WritePin(USB_PowerSwitchOn_GPIO_Port, USB_PowerSwitchOn_Pin, GPIO_PIN_RESET);
+
+  /*Configure GPIO pin : USER_Btn_Pin */
+  GPIO_InitStruct.Pin = USER_Btn_Pin;
+  GPIO_InitStruct.Mode = GPIO_MODE_IT_RISING;
+  GPIO_InitStruct.Pull = GPIO_NOPULL;
+  HAL_GPIO_Init(USER_Btn_GPIO_Port, &GPIO_InitStruct);
+
+  /*Configure GPIO pins : LD3_Pin LD2_Pin */
+  GPIO_InitStruct.Pin = LD3_Pin|LD2_Pin;
+  GPIO_InitStruct.Mode = GPIO_MODE_OUTPUT_PP;
+  GPIO_InitStruct.Pull = GPIO_NOPULL;
+  GPIO_InitStruct.Speed = GPIO_SPEED_FREQ_LOW;
+  HAL_GPIO_Init(GPIOB, &GPIO_InitStruct);
+
+  /*Configure GPIO pin : USB_PowerSwitchOn_Pin */
+  GPIO_InitStruct.Pin = USB_PowerSwitchOn_Pin;
+  GPIO_InitStruct.Mode = GPIO_MODE_OUTPUT_PP;
+  GPIO_InitStruct.Pull = GPIO_NOPULL;
+  GPIO_InitStruct.Speed = GPIO_SPEED_FREQ_LOW;
+  HAL_GPIO_Init(USB_PowerSwitchOn_GPIO_Port, &GPIO_InitStruct);
+
+  /*Configure GPIO pin : USB_OverCurrent_Pin */
+  GPIO_InitStruct.Pin = USB_OverCurrent_Pin;
+  GPIO_InitStruct.Mode = GPIO_MODE_INPUT;
+  GPIO_InitStruct.Pull = GPIO_NOPULL;
+  HAL_GPIO_Init(USB_OverCurrent_GPIO_Port, &GPIO_InitStruct);
+
+}
+
+/* USER CODE BEGIN 4 */
+
+/* USER CODE END 4 */
+
+/**
+  * @brief  This function is executed in case of error occurrence.
+  * @retval None
+  */
+void Error_Handler(void)
+{
+  /* USER CODE BEGIN Error_Handler_Debug */
+  /* User can add his own implementation to report the HAL error return state */
+
+  /* USER CODE END Error_Handler_Debug */
+}
+
+#ifdef  USE_FULL_ASSERT
+/**
+  * @brief  Reports the name of the source file and the source line number
+  *         where the assert_param error has occurred.
+  * @param  file: pointer to the source file name
+  * @param  line: assert_param error line source number
+  * @retval None
+  */
+void assert_failed(uint8_t *file, uint32_t line)
+{ 
+  /* USER CODE BEGIN 6 */
+  /* User can add his own implementation to report the file name and line number,
+     tex: printf("Wrong parameters value: file %s on line %d\r\n", file, line) */
+  /* USER CODE END 6 */
+}
+#endif /* USE_FULL_ASSERT */
+
+/************************ (C) COPYRIGHT STMicroelectronics *****END OF FILE****/

bsp/stm32/stm32f767-st-nucleo/board/CubeMX_Config/Src/stm32f7xx_hal_msp.c

@@ -0,0 +1,364 @@
+/* USER CODE BEGIN Header */
+/**
+  ******************************************************************************
+  * File Name          : stm32f7xx_hal_msp.c
+  * Description        : This file provides code for the MSP Initialization 
+  *                      and de-Initialization codes.
+  ******************************************************************************
+  ** This notice applies to any and all portions of this file
+  * that are not between comment pairs USER CODE BEGIN and
+  * USER CODE END. Other portions of this file, whether 
+  * inserted by the user or by software development tools
+  * are owned by their respective copyright owners.
+  *
+  * COPYRIGHT(c) 2018 STMicroelectronics
+  *
+  * Redistribution and use in source and binary forms, with or without modification,
+  * are permitted provided that the following conditions are met:
+  *   1. Redistributions of source code must retain the above copyright notice,
+  *      this list of conditions and the following disclaimer.
+  *   2. Redistributions in binary form must reproduce the above copyright notice,
+  *      this list of conditions and the following disclaimer in the documentation
+  *      and/or other materials provided with the distribution.
+  *   3. Neither the name of STMicroelectronics nor the names of its contributors
+  *      may be used to endorse or promote products derived from this software
+  *      without specific prior written permission.
+  *
+  * THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS "AS IS"
+  * AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE
+  * IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE
+  * DISCLAIMED. IN NO EVENT SHALL THE COPYRIGHT HOLDER OR CONTRIBUTORS BE LIABLE
+  * FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL
+  * DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR
+  * SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER
+  * CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY,
+  * OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE
+  * OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.
+  *
+  ******************************************************************************
+  */
+/* USER CODE END Header */
+
+/* Includes ------------------------------------------------------------------*/
+#include "main.h"
+/* USER CODE BEGIN Includes */
+
+/* USER CODE END Includes */
+
+/* Private typedef -----------------------------------------------------------*/
+/* USER CODE BEGIN TD */
+
+/* USER CODE END TD */
+
+/* Private define ------------------------------------------------------------*/
+/* USER CODE BEGIN Define */
+ 
+/* USER CODE END Define */
+
+/* Private macro -------------------------------------------------------------*/
+/* USER CODE BEGIN Macro */
+
+/* USER CODE END Macro */
+
+/* Private variables ---------------------------------------------------------*/
+/* USER CODE BEGIN PV */
+
+/* USER CODE END PV */
+
+/* Private function prototypes -----------------------------------------------*/
+/* USER CODE BEGIN PFP */
+
+/* USER CODE END PFP */
+
+/* External functions --------------------------------------------------------*/
+/* USER CODE BEGIN ExternalFunctions */
+
+/* USER CODE END ExternalFunctions */
+
+/* USER CODE BEGIN 0 */
+
+/* USER CODE END 0 */
+/**
+  * Initializes the Global MSP.
+  */
+void HAL_MspInit(void)
+{
+  /* USER CODE BEGIN MspInit 0 */
+
+  /* USER CODE END MspInit 0 */
+
+  __HAL_RCC_PWR_CLK_ENABLE();
+  __HAL_RCC_SYSCFG_CLK_ENABLE();
+
+  /* System interrupt init*/
+
+  /* USER CODE BEGIN MspInit 1 */
+
+  /* USER CODE END MspInit 1 */
+}
+
+/**
+* @brief ETH MSP Initialization
+* This function configures the hardware resources used in this example
+* @param heth: ETH handle pointer
+* @retval None
+*/
+void HAL_ETH_MspInit(ETH_HandleTypeDef* heth)
+{
+
+  GPIO_InitTypeDef GPIO_InitStruct = {0};
+  if(heth->Instance==ETH)
+  {
+  /* USER CODE BEGIN ETH_MspInit 0 */
+
+  /* USER CODE END ETH_MspInit 0 */
+    /* Peripheral clock enable */
+    __HAL_RCC_ETH_CLK_ENABLE();
+  
+    __HAL_RCC_GPIOC_CLK_ENABLE();
+    __HAL_RCC_GPIOA_CLK_ENABLE();
+    __HAL_RCC_GPIOB_CLK_ENABLE();
+    __HAL_RCC_GPIOG_CLK_ENABLE();
+    /**ETH GPIO Configuration    
+    PC1     ------> ETH_MDC
+    PA1     ------> ETH_REF_CLK
+    PA2     ------> ETH_MDIO
+    PA7     ------> ETH_CRS_DV
+    PC4     ------> ETH_RXD0
+    PC5     ------> ETH_RXD1
+    PB13     ------> ETH_TXD1
+    PG11     ------> ETH_TX_EN
+    PG13     ------> ETH_TXD0 
+    */
+    GPIO_InitStruct.Pin = RMII_MDC_Pin|RMII_RXD0_Pin|RMII_RXD1_Pin;
+    GPIO_InitStruct.Mode = GPIO_MODE_AF_PP;
+    GPIO_InitStruct.Pull = GPIO_NOPULL;
+    GPIO_InitStruct.Speed = GPIO_SPEED_FREQ_VERY_HIGH;
+    GPIO_InitStruct.Alternate = GPIO_AF11_ETH;
+    HAL_GPIO_Init(GPIOC, &GPIO_InitStruct);
+
+    GPIO_InitStruct.Pin = RMII_REF_CLK_Pin|RMII_MDIO_Pin|RMII_CRS_DV_Pin;
+    GPIO_InitStruct.Mode = GPIO_MODE_AF_PP;
+    GPIO_InitStruct.Pull = GPIO_NOPULL;
+    GPIO_InitStruct.Speed = GPIO_SPEED_FREQ_VERY_HIGH;
+    GPIO_InitStruct.Alternate = GPIO_AF11_ETH;
+    HAL_GPIO_Init(GPIOA, &GPIO_InitStruct);
+
+    GPIO_InitStruct.Pin = RMII_TXD1_Pin;
+    GPIO_InitStruct.Mode = GPIO_MODE_AF_PP;
+    GPIO_InitStruct.Pull = GPIO_NOPULL;
+    GPIO_InitStruct.Speed = GPIO_SPEED_FREQ_VERY_HIGH;
+    GPIO_InitStruct.Alternate = GPIO_AF11_ETH;
+    HAL_GPIO_Init(RMII_TXD1_GPIO_Port, &GPIO_InitStruct);
+
+    GPIO_InitStruct.Pin = RMII_TX_EN_Pin|RMII_TXD0_Pin;
+    GPIO_InitStruct.Mode = GPIO_MODE_AF_PP;
+    GPIO_InitStruct.Pull = GPIO_NOPULL;
+    GPIO_InitStruct.Speed = GPIO_SPEED_FREQ_VERY_HIGH;
+    GPIO_InitStruct.Alternate = GPIO_AF11_ETH;
+    HAL_GPIO_Init(GPIOG, &GPIO_InitStruct);
+
+  /* USER CODE BEGIN ETH_MspInit 1 */
+
+  /* USER CODE END ETH_MspInit 1 */
+  }
+
+}
+
+/**
+* @brief ETH MSP De-Initialization
+* This function freeze the hardware resources used in this example
+* @param heth: ETH handle pointer
+* @retval None
+*/
+
+void HAL_ETH_MspDeInit(ETH_HandleTypeDef* heth)
+{
+
+  if(heth->Instance==ETH)
+  {
+  /* USER CODE BEGIN ETH_MspDeInit 0 */
+
+  /* USER CODE END ETH_MspDeInit 0 */
+    /* Peripheral clock disable */
+    __HAL_RCC_ETH_CLK_DISABLE();
+  
+    /**ETH GPIO Configuration    
+    PC1     ------> ETH_MDC
+    PA1     ------> ETH_REF_CLK
+    PA2     ------> ETH_MDIO
+    PA7     ------> ETH_CRS_DV
+    PC4     ------> ETH_RXD0
+    PC5     ------> ETH_RXD1
+    PB13     ------> ETH_TXD1
+    PG11     ------> ETH_TX_EN
+    PG13     ------> ETH_TXD0 
+    */
+    HAL_GPIO_DeInit(GPIOC, RMII_MDC_Pin|RMII_RXD0_Pin|RMII_RXD1_Pin);
+
+    HAL_GPIO_DeInit(GPIOA, RMII_REF_CLK_Pin|RMII_MDIO_Pin|RMII_CRS_DV_Pin);
+
+    HAL_GPIO_DeInit(RMII_TXD1_GPIO_Port, RMII_TXD1_Pin);
+
+    HAL_GPIO_DeInit(GPIOG, RMII_TX_EN_Pin|RMII_TXD0_Pin);
+
+  /* USER CODE BEGIN ETH_MspDeInit 1 */
+
+  /* USER CODE END ETH_MspDeInit 1 */
+  }
+
+}
+
+/**
+* @brief UART MSP Initialization
+* This function configures the hardware resources used in this example
+* @param huart: UART handle pointer
+* @retval None
+*/
+void HAL_UART_MspInit(UART_HandleTypeDef* huart)
+{
+
+  GPIO_InitTypeDef GPIO_InitStruct = {0};
+  if(huart->Instance==USART3)
+  {
+  /* USER CODE BEGIN USART3_MspInit 0 */
+
+  /* USER CODE END USART3_MspInit 0 */
+    /* Peripheral clock enable */
+    __HAL_RCC_USART3_CLK_ENABLE();
+  
+    __HAL_RCC_GPIOD_CLK_ENABLE();
+    /**USART3 GPIO Configuration    
+    PD8     ------> USART3_TX
+    PD9     ------> USART3_RX 
+    */
+    GPIO_InitStruct.Pin = STLK_RX_Pin|STLK_TX_Pin;
+    GPIO_InitStruct.Mode = GPIO_MODE_AF_PP;
+    GPIO_InitStruct.Pull = GPIO_NOPULL;
+    GPIO_InitStruct.Speed = GPIO_SPEED_FREQ_VERY_HIGH;
+    GPIO_InitStruct.Alternate = GPIO_AF7_USART3;
+    HAL_GPIO_Init(GPIOD, &GPIO_InitStruct);
+
+  /* USER CODE BEGIN USART3_MspInit 1 */
+
+  /* USER CODE END USART3_MspInit 1 */
+  }
+
+}
+
+/**
+* @brief UART MSP De-Initialization
+* This function freeze the hardware resources used in this example
+* @param huart: UART handle pointer
+* @retval None
+*/
+
+void HAL_UART_MspDeInit(UART_HandleTypeDef* huart)
+{
+
+  if(huart->Instance==USART3)
+  {
+  /* USER CODE BEGIN USART3_MspDeInit 0 */
+
+  /* USER CODE END USART3_MspDeInit 0 */
+    /* Peripheral clock disable */
+    __HAL_RCC_USART3_CLK_DISABLE();
+  
+    /**USART3 GPIO Configuration    
+    PD8     ------> USART3_TX
+    PD9     ------> USART3_RX 
+    */
+    HAL_GPIO_DeInit(GPIOD, STLK_RX_Pin|STLK_TX_Pin);
+
+  /* USER CODE BEGIN USART3_MspDeInit 1 */
+
+  /* USER CODE END USART3_MspDeInit 1 */
+  }
+
+}
+
+/**
+* @brief PCD MSP Initialization
+* This function configures the hardware resources used in this example
+* @param hpcd: PCD handle pointer
+* @retval None
+*/
+void HAL_PCD_MspInit(PCD_HandleTypeDef* hpcd)
+{
+
+  GPIO_InitTypeDef GPIO_InitStruct = {0};
+  if(hpcd->Instance==USB_OTG_FS)
+  {
+  /* USER CODE BEGIN USB_OTG_FS_MspInit 0 */
+
+  /* USER CODE END USB_OTG_FS_MspInit 0 */
+  
+    __HAL_RCC_GPIOA_CLK_ENABLE();
+    /**USB_OTG_FS GPIO Configuration    
+    PA8     ------> USB_OTG_FS_SOF
+    PA9     ------> USB_OTG_FS_VBUS
+    PA10     ------> USB_OTG_FS_ID
+    PA11     ------> USB_OTG_FS_DM
+    PA12     ------> USB_OTG_FS_DP 
+    */
+    GPIO_InitStruct.Pin = USB_SOF_Pin|USB_ID_Pin|USB_DM_Pin|USB_DP_Pin;
+    GPIO_InitStruct.Mode = GPIO_MODE_AF_PP;
+    GPIO_InitStruct.Pull = GPIO_NOPULL;
+    GPIO_InitStruct.Speed = GPIO_SPEED_FREQ_VERY_HIGH;
+    GPIO_InitStruct.Alternate = GPIO_AF10_OTG_FS;
+    HAL_GPIO_Init(GPIOA, &GPIO_InitStruct);
+
+    GPIO_InitStruct.Pin = USB_VBUS_Pin;
+    GPIO_InitStruct.Mode = GPIO_MODE_INPUT;
+    GPIO_InitStruct.Pull = GPIO_NOPULL;
+    HAL_GPIO_Init(USB_VBUS_GPIO_Port, &GPIO_InitStruct);
+
+    /* Peripheral clock enable */
+    __HAL_RCC_USB_OTG_FS_CLK_ENABLE();
+  /* USER CODE BEGIN USB_OTG_FS_MspInit 1 */
+
+  /* USER CODE END USB_OTG_FS_MspInit 1 */
+  }
+
+}
+
+/**
+* @brief PCD MSP De-Initialization
+* This function freeze the hardware resources used in this example
+* @param hpcd: PCD handle pointer
+* @retval None
+*/
+
+void HAL_PCD_MspDeInit(PCD_HandleTypeDef* hpcd)
+{
+
+  if(hpcd->Instance==USB_OTG_FS)
+  {
+  /* USER CODE BEGIN USB_OTG_FS_MspDeInit 0 */
+
+  /* USER CODE END USB_OTG_FS_MspDeInit 0 */
+    /* Peripheral clock disable */
+    __HAL_RCC_USB_OTG_FS_CLK_DISABLE();
+  
+    /**USB_OTG_FS GPIO Configuration    
+    PA8     ------> USB_OTG_FS_SOF
+    PA9     ------> USB_OTG_FS_VBUS
+    PA10     ------> USB_OTG_FS_ID
+    PA11     ------> USB_OTG_FS_DM
+    PA12     ------> USB_OTG_FS_DP 
+    */
+    HAL_GPIO_DeInit(GPIOA, USB_SOF_Pin|USB_VBUS_Pin|USB_ID_Pin|USB_DM_Pin 
+                          |USB_DP_Pin);
+
+  /* USER CODE BEGIN USB_OTG_FS_MspDeInit 1 */
+
+  /* USER CODE END USB_OTG_FS_MspDeInit 1 */
+  }
+
+}
+
+/* USER CODE BEGIN 1 */
+
+/* USER CODE END 1 */
+
+/************************ (C) COPYRIGHT STMicroelectronics *****END OF FILE****/

bsp/stm32/stm32f767-st-nucleo/board/CubeMX_Config/Src/stm32f7xx_it.c

@@ -0,0 +1,217 @@
+/* USER CODE BEGIN Header */
+/**
+  ******************************************************************************
+  * @file    stm32f7xx_it.c
+  * @brief   Interrupt Service Routines.
+  ******************************************************************************
+  *
+  * COPYRIGHT(c) 2018 STMicroelectronics
+  *
+  * Redistribution and use in source and binary forms, with or without modification,
+  * are permitted provided that the following conditions are met:
+  *   1. Redistributions of source code must retain the above copyright notice,
+  *      this list of conditions and the following disclaimer.
+  *   2. Redistributions in binary form must reproduce the above copyright notice,
+  *      this list of conditions and the following disclaimer in the documentation
+  *      and/or other materials provided with the distribution.
+  *   3. Neither the name of STMicroelectronics nor the names of its contributors
+  *      may be used to endorse or promote products derived from this software
+  *      without specific prior written permission.
+  *
+  * THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS "AS IS"
+  * AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE
+  * IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE
+  * DISCLAIMED. IN NO EVENT SHALL THE COPYRIGHT HOLDER OR CONTRIBUTORS BE LIABLE
+  * FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL
+  * DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR
+  * SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER
+  * CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY,
+  * OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE
+  * OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.
+  *
+  ******************************************************************************
+  */
+/* USER CODE END Header */
+
+/* Includes ------------------------------------------------------------------*/
+#include "main.h"
+#include "stm32f7xx_it.h"
+/* Private includes ----------------------------------------------------------*/
+/* USER CODE BEGIN Includes */
+/* USER CODE END Includes */
+
+/* Private typedef -----------------------------------------------------------*/
+/* USER CODE BEGIN TD */
+
+/* USER CODE END TD */
+
+/* Private define ------------------------------------------------------------*/
+/* USER CODE BEGIN PD */
+ 
+/* USER CODE END PD */
+
+/* Private macro -------------------------------------------------------------*/
+/* USER CODE BEGIN PM */
+
+/* USER CODE END PM */
+
+/* Private variables ---------------------------------------------------------*/
+/* USER CODE BEGIN PV */
+
+/* USER CODE END PV */
+
+/* Private function prototypes -----------------------------------------------*/
+/* USER CODE BEGIN PFP */
+
+/* USER CODE END PFP */
+
+/* Private user code ---------------------------------------------------------*/
+/* USER CODE BEGIN 0 */
+
+/* USER CODE END 0 */
+
+/* External variables --------------------------------------------------------*/
+/* USER CODE BEGIN EV */
+
+/* USER CODE END EV */
+
+/******************************************************************************/
+/*           Cortex-M7 Processor Interruption and Exception Handlers          */ 
+/******************************************************************************/
+/**
+  * @brief This function handles Non maskable interrupt.
+  */
+void NMI_Handler(void)
+{
+  /* USER CODE BEGIN NonMaskableInt_IRQn 0 */
+
+  /* USER CODE END NonMaskableInt_IRQn 0 */
+  /* USER CODE BEGIN NonMaskableInt_IRQn 1 */
+
+  /* USER CODE END NonMaskableInt_IRQn 1 */
+}
+
+/**
+  * @brief This function handles Hard fault interrupt.
+  */
+void HardFault_Handler(void)
+{
+  /* USER CODE BEGIN HardFault_IRQn 0 */
+
+  /* USER CODE END HardFault_IRQn 0 */
+  while (1)
+  {
+    /* USER CODE BEGIN W1_HardFault_IRQn 0 */
+    /* USER CODE END W1_HardFault_IRQn 0 */
+  }
+}
+
+/**
+  * @brief This function handles Memory management fault.
+  */
+void MemManage_Handler(void)
+{
+  /* USER CODE BEGIN MemoryManagement_IRQn 0 */
+
+  /* USER CODE END MemoryManagement_IRQn 0 */
+  while (1)
+  {
+    /* USER CODE BEGIN W1_MemoryManagement_IRQn 0 */
+    /* USER CODE END W1_MemoryManagement_IRQn 0 */
+  }
+}
+
+/**
+  * @brief This function handles Pre-fetch fault, memory access fault.
+  */
+void BusFault_Handler(void)
+{
+  /* USER CODE BEGIN BusFault_IRQn 0 */
+
+  /* USER CODE END BusFault_IRQn 0 */
+  while (1)
+  {
+    /* USER CODE BEGIN W1_BusFault_IRQn 0 */
+    /* USER CODE END W1_BusFault_IRQn 0 */
+  }
+}
+
+/**
+  * @brief This function handles Undefined instruction or illegal state.
+  */
+void UsageFault_Handler(void)
+{
+  /* USER CODE BEGIN UsageFault_IRQn 0 */
+
+  /* USER CODE END UsageFault_IRQn 0 */
+  while (1)
+  {
+    /* USER CODE BEGIN W1_UsageFault_IRQn 0 */
+    /* USER CODE END W1_UsageFault_IRQn 0 */
+  }
+}
+
+/**
+  * @brief This function handles System service call via SWI instruction.
+  */
+void SVC_Handler(void)
+{
+  /* USER CODE BEGIN SVCall_IRQn 0 */
+
+  /* USER CODE END SVCall_IRQn 0 */
+  /* USER CODE BEGIN SVCall_IRQn 1 */
+
+  /* USER CODE END SVCall_IRQn 1 */
+}
+
+/**
+  * @brief This function handles Debug monitor.
+  */
+void DebugMon_Handler(void)
+{
+  /* USER CODE BEGIN DebugMonitor_IRQn 0 */
+
+  /* USER CODE END DebugMonitor_IRQn 0 */
+  /* USER CODE BEGIN DebugMonitor_IRQn 1 */
+
+  /* USER CODE END DebugMonitor_IRQn 1 */
+}
+
+/**
+  * @brief This function handles Pendable request for system service.
+  */
+void PendSV_Handler(void)
+{
+  /* USER CODE BEGIN PendSV_IRQn 0 */
+
+  /* USER CODE END PendSV_IRQn 0 */
+  /* USER CODE BEGIN PendSV_IRQn 1 */
+
+  /* USER CODE END PendSV_IRQn 1 */
+}
+
+/**
+  * @brief This function handles System tick timer.
+  */
+void SysTick_Handler(void)
+{
+  /* USER CODE BEGIN SysTick_IRQn 0 */
+
+  /* USER CODE END SysTick_IRQn 0 */
+  HAL_IncTick();
+  /* USER CODE BEGIN SysTick_IRQn 1 */
+
+  /* USER CODE END SysTick_IRQn 1 */
+}
+
+/******************************************************************************/
+/* STM32F7xx Peripheral Interrupt Handlers                                    */
+/* Add here the Interrupt Handlers for the used peripherals.                  */
+/* For the available peripheral interrupt handler names,                      */
+/* please refer to the startup file (startup_stm32f7xx.s).                    */
+/******************************************************************************/
+
+/* USER CODE BEGIN 1 */
+
+/* USER CODE END 1 */
+/************************ (C) COPYRIGHT STMicroelectronics *****END OF FILE****/

bsp/stm32/stm32f767-st-nucleo/board/CubeMX_Config/Src/system_stm32f7xx.c

@@ -0,0 +1,278 @@
+/**
+  ******************************************************************************
+  * @file    system_stm32f7xx.c
+  * @author  MCD Application Team
+  * @brief   CMSIS Cortex-M7 Device Peripheral Access Layer System Source File.
+  *
+  *   This file provides two functions and one global variable to be called from 
+  *   user application:
+  *      - SystemInit(): This function is called at startup just after reset and 
+  *                      before branch to main program. This call is made inside
+  *                      the "startup_stm32f7xx.s" file.
+  *
+  *      - SystemCoreClock variable: Contains the core clock (HCLK), it can be used
+  *                                  by the user application to setup the SysTick 
+  *                                  timer or configure other parameters.
+  *                                     
+  *      - SystemCoreClockUpdate(): Updates the variable SystemCoreClock and must
+  *                                 be called whenever the core clock is changed
+  *                                 during program execution.
+  *
+  *
+  ******************************************************************************
+  * @attention
+  *
+  * <h2><center>&copy; COPYRIGHT 2016 STMicroelectronics</center></h2>
+  *
+  * Redistribution and use in source and binary forms, with or without modification,
+  * are permitted provided that the following conditions are met:
+  *   1. Redistributions of source code must retain the above copyright notice,
+  *      this list of conditions and the following disclaimer.
+  *   2. Redistributions in binary form must reproduce the above copyright notice,
+  *      this list of conditions and the following disclaimer in the documentation
+  *      and/or other materials provided with the distribution.
+  *   3. Neither the name of STMicroelectronics nor the names of its contributors
+  *      may be used to endorse or promote products derived from this software
+  *      without specific prior written permission.
+  *
+  * THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS "AS IS"
+  * AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE
+  * IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE
+  * DISCLAIMED. IN NO EVENT SHALL THE COPYRIGHT HOLDER OR CONTRIBUTORS BE LIABLE
+  * FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL
+  * DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR
+  * SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER
+  * CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY,
+  * OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE
+  * OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.
+  *
+  ******************************************************************************
+  */
+
+/** @addtogroup CMSIS
+  * @{
+  */
+
+/** @addtogroup stm32f7xx_system
+  * @{
+  */  
+  
+/** @addtogroup STM32F7xx_System_Private_Includes
+  * @{
+  */
+
+#include "stm32f7xx.h"
+
+#if !defined  (HSE_VALUE) 
+  #define HSE_VALUE    ((uint32_t)25000000) /*!< Default value of the External oscillator in Hz */
+#endif /* HSE_VALUE */
+
+#if !defined  (HSI_VALUE)
+  #define HSI_VALUE    ((uint32_t)16000000) /*!< Value of the Internal oscillator in Hz*/
+#endif /* HSI_VALUE */
+
+/**
+  * @}
+  */
+
+/** @addtogroup STM32F7xx_System_Private_TypesDefinitions
+  * @{
+  */
+
+/**
+  * @}
+  */
+
+/** @addtogroup STM32F7xx_System_Private_Defines
+  * @{
+  */
+
+/************************* Miscellaneous Configuration ************************/
+
+/*!< Uncomment the following line if you need to relocate your vector Table in
+     Internal SRAM. */
+/* #define VECT_TAB_SRAM */
+#define VECT_TAB_OFFSET  0x00 /*!< Vector Table base offset field. 
+                                   This value must be a multiple of 0x200. */
+/******************************************************************************/
+
+/**
+  * @}
+  */
+
+/** @addtogroup STM32F7xx_System_Private_Macros
+  * @{
+  */
+
+/**
+  * @}
+  */
+
+/** @addtogroup STM32F7xx_System_Private_Variables
+  * @{
+  */
+
+  /* This variable is updated in three ways:
+      1) by calling CMSIS function SystemCoreClockUpdate()
+      2) by calling HAL API function HAL_RCC_GetHCLKFreq()
+      3) each time HAL_RCC_ClockConfig() is called to configure the system clock frequency 
+         Note: If you use this function to configure the system clock; then there
+               is no need to call the 2 first functions listed above, since SystemCoreClock
+               variable is updated automatically.
+  */
+  uint32_t SystemCoreClock = 16000000;
+  const uint8_t AHBPrescTable[16] = {0, 0, 0, 0, 0, 0, 0, 0, 1, 2, 3, 4, 6, 7, 8, 9};
+  const uint8_t APBPrescTable[8] = {0, 0, 0, 0, 1, 2, 3, 4};
+
+/**
+  * @}
+  */
+
+/** @addtogroup STM32F7xx_System_Private_FunctionPrototypes
+  * @{
+  */
+
+/**
+  * @}
+  */
+
+/** @addtogroup STM32F7xx_System_Private_Functions
+  * @{
+  */
+
+/**
+  * @brief  Setup the microcontroller system
+  *         Initialize the Embedded Flash Interface, the PLL and update the 
+  *         SystemFrequency variable.
+  * @param  None
+  * @retval None
+  */
+void SystemInit(void)
+{
+  /* FPU settings ------------------------------------------------------------*/
+  #if (__FPU_PRESENT == 1) && (__FPU_USED == 1)
+    SCB->CPACR |= ((3UL << 10*2)|(3UL << 11*2));  /* set CP10 and CP11 Full Access */
+  #endif
+  /* Reset the RCC clock configuration to the default reset state ------------*/
+  /* Set HSION bit */
+  RCC->CR |= (uint32_t)0x00000001;
+
+  /* Reset CFGR register */
+  RCC->CFGR = 0x00000000;
+
+  /* Reset HSEON, CSSON and PLLON bits */
+  RCC->CR &= (uint32_t)0xFEF6FFFF;
+
+  /* Reset PLLCFGR register */
+  RCC->PLLCFGR = 0x24003010;
+
+  /* Reset HSEBYP bit */
+  RCC->CR &= (uint32_t)0xFFFBFFFF;
+
+  /* Disable all interrupts */
+  RCC->CIR = 0x00000000;
+
+  /* Configure the Vector Table location add offset address ------------------*/
+#ifdef VECT_TAB_SRAM
+  SCB->VTOR = RAMDTCM_BASE | VECT_TAB_OFFSET; /* Vector Table Relocation in Internal SRAM */
+#else
+  SCB->VTOR = FLASH_BASE | VECT_TAB_OFFSET; /* Vector Table Relocation in Internal FLASH */
+#endif
+}
+
+/**
+   * @brief  Update SystemCoreClock variable according to Clock Register Values.
+  *         The SystemCoreClock variable contains the core clock (HCLK), it can
+  *         be used by the user application to setup the SysTick timer or configure
+  *         other parameters.
+  *           
+  * @note   Each time the core clock (HCLK) changes, this function must be called
+  *         to update SystemCoreClock variable value. Otherwise, any configuration
+  *         based on this variable will be incorrect.         
+  *     
+  * @note   - The system frequency computed by this function is not the real 
+  *           frequency in the chip. It is calculated based on the predefined 
+  *           constant and the selected clock source:
+  *             
+  *           - If SYSCLK source is HSI, SystemCoreClock will contain the HSI_VALUE(*)
+  *                                              
+  *           - If SYSCLK source is HSE, SystemCoreClock will contain the HSE_VALUE(**)
+  *                          
+  *           - If SYSCLK source is PLL, SystemCoreClock will contain the HSE_VALUE(**) 
+  *             or HSI_VALUE(*) multiplied/divided by the PLL factors.
+  *         
+  *         (*) HSI_VALUE is a constant defined in stm32f7xx_hal_conf.h file (default value
+  *             16 MHz) but the real value may vary depending on the variations
+  *             in voltage and temperature.   
+  *    
+  *         (**) HSE_VALUE is a constant defined in stm32f7xx_hal_conf.h file (default value
+  *              25 MHz), user has to ensure that HSE_VALUE is same as the real
+  *              frequency of the crystal used. Otherwise, this function may
+  *              have wrong result.
+  *                
+  *         - The result of this function could be not correct when using fractional
+  *           value for HSE crystal.
+  *     
+  * @param  None
+  * @retval None
+  */
+void SystemCoreClockUpdate(void)
+{
+  uint32_t tmp = 0, pllvco = 0, pllp = 2, pllsource = 0, pllm = 2;
+  
+  /* Get SYSCLK source -------------------------------------------------------*/
+  tmp = RCC->CFGR & RCC_CFGR_SWS;
+
+  switch (tmp)
+  {
+    case 0x00:  /* HSI used as system clock source */
+      SystemCoreClock = HSI_VALUE;
+      break;
+    case 0x04:  /* HSE used as system clock source */
+      SystemCoreClock = HSE_VALUE;
+      break;
+    case 0x08:  /* PLL used as system clock source */
+
+      /* PLL_VCO = (HSE_VALUE or HSI_VALUE / PLL_M) * PLL_N
+         SYSCLK = PLL_VCO / PLL_P
+         */    
+      pllsource = (RCC->PLLCFGR & RCC_PLLCFGR_PLLSRC) >> 22;
+      pllm = RCC->PLLCFGR & RCC_PLLCFGR_PLLM;
+      
+      if (pllsource != 0)
+      {
+        /* HSE used as PLL clock source */
+        pllvco = (HSE_VALUE / pllm) * ((RCC->PLLCFGR & RCC_PLLCFGR_PLLN) >> 6);
+      }
+      else
+      {
+        /* HSI used as PLL clock source */
+        pllvco = (HSI_VALUE / pllm) * ((RCC->PLLCFGR & RCC_PLLCFGR_PLLN) >> 6);      
+      }
+
+      pllp = (((RCC->PLLCFGR & RCC_PLLCFGR_PLLP) >>16) + 1 ) *2;
+      SystemCoreClock = pllvco/pllp;
+      break;
+    default:
+      SystemCoreClock = HSI_VALUE;
+      break;
+  }
+  /* Compute HCLK frequency --------------------------------------------------*/
+  /* Get HCLK prescaler */
+  tmp = AHBPrescTable[((RCC->CFGR & RCC_CFGR_HPRE) >> 4)];
+  /* HCLK frequency */
+  SystemCoreClock >>= tmp;
+}
+
+/**
+  * @}
+  */
+
+/**
+  * @}
+  */
+  
+/**
+  * @}
+  */    
+/************************ (C) COPYRIGHT STMicroelectronics *****END OF FILE****/

bsp/stm32/stm32f767-st-nucleo/board/Kconfig

@@ -0,0 +1,46 @@
+menu "Hardware Drivers Config"
+
+config SOC_STM32F767ZI 
+    bool
+    select SOC_SERIES_STM32F7
+    default y
+
+menu "Onboard Peripheral Drivers"
+
+ config BSP_USING_USB_TO_USART 
+        bool "Enable USB TO USART (uart3)"
+        select BSP_USING_UART3
+        default y
+        
+ 
+endmenu
+
+menu "On-chip Peripheral Drivers"
+
+    config BSP_USING_GPIO
+        bool "Enable GPIO"
+        select RT_USING_PIN
+        default y
+
+    menuconfig BSP_USING_UART
+        bool "Enable UART3"
+        default y
+        select RT_USING_SERIAL
+        if BSP_USING_UART
+            config BSP_USING_UART3
+                bool "Enable UART3"
+                default y
+
+            config BSP_UART3_RX_USING_DMA
+                bool "Enable UART3 RX DMA"
+                depends on BSP_USING_UART3 && RT_SERIAL_USING_DMA
+                default n
+        endif
+
+endmenu
+
+menu "Board extended module Drivers"
+
+endmenu
+ 
+endmenu

bsp/stm32/stm32f767-st-nucleo/board/SConscript

@@ -0,0 +1,26 @@
+import rtconfig
+from building import *
+
+cwd = GetCurrentDir()
+
+# add the general drivers.
+src = Glob('board.c')
+src += Glob('CubeMX_Config/Src/stm32f7xx_hal_msp.c')
+
+path = [cwd]
+path += [cwd + '/CubeMX_Config/Inc']
+
+if rtconfig.CROSS_TOOL == 'gcc':
+    src += [cwd + '/../../libraries/STM32F7xx_HAL/CMSIS/Device/ST/STM32F7xx/Source/Templates/gcc/startup_stm32f767xx.s']
+elif rtconfig.CROSS_TOOL == 'keil':
+    src += [cwd + '/../../libraries/STM32F7xx_HAL/CMSIS/Device/ST/STM32F7xx/Source/Templates/arm/startup_stm32f767xx.s']
+elif rtconfig.CROSS_TOOL == 'iar':
+    src += [cwd + '/../../libraries/STM32F7xx_HAL/CMSIS/Device/ST/STM32F7xx/Source/Templates/iar/startup_stm32f767xx.s']
+
+# STM32F756xx || STM32F746xx || STM32F745xx || STM32F767xx  || 
+# STM32F769xx || STM32F777xx || STM32F779xx || STM32F722xx  || 
+# STM32F723xx || STM32F732xx || STM32F733xx || STM32F730xx  || STM32F750xx
+# You can select chips from the list above
+CPPDEFINES = ['STM32F767xx']
+group = DefineGroup('Drivers', src, depend = [''], CPPPATH = path, CPPDEFINES = CPPDEFINES)
+Return('group')

bsp/stm32/stm32f767-st-nucleo/board/board.c

@@ -0,0 +1,72 @@
+/*
+ * Copyright (c) 2006-2018, RT-Thread Development Team
+ *
+ * SPDX-License-Identifier: Apache-2.0
+ *
+ * Change Logs:
+ * Date           Author       Notes
+ * 2018-11-06     SummerGift   change to new framework
+ * 2019-1-10      e31207077    change to new framework
+ */
+
+#include "board.h"
+
+/**
+  * @brief System Clock Configuration
+  * @retval None
+  */
+void SystemClock_Config(void)
+{
+  RCC_OscInitTypeDef RCC_OscInitStruct = {0};
+  RCC_ClkInitTypeDef RCC_ClkInitStruct = {0};
+  RCC_PeriphCLKInitTypeDef PeriphClkInitStruct = {0};
+
+  /**Configure LSE Drive Capability 
+  */
+  HAL_PWR_EnableBkUpAccess();
+  /**Configure the main internal regulator output voltage 
+  */
+  __HAL_RCC_PWR_CLK_ENABLE();
+  __HAL_PWR_VOLTAGESCALING_CONFIG(PWR_REGULATOR_VOLTAGE_SCALE1);
+  /**Initializes the CPU, AHB and APB busses clocks 
+  */
+  RCC_OscInitStruct.OscillatorType = RCC_OSCILLATORTYPE_HSE;
+  RCC_OscInitStruct.HSEState = RCC_HSE_BYPASS;
+  RCC_OscInitStruct.PLL.PLLState = RCC_PLL_ON;
+  RCC_OscInitStruct.PLL.PLLSource = RCC_PLLSOURCE_HSE;
+  RCC_OscInitStruct.PLL.PLLM = 8;
+  RCC_OscInitStruct.PLL.PLLN = 432;
+  RCC_OscInitStruct.PLL.PLLP = RCC_PLLP_DIV2;
+  RCC_OscInitStruct.PLL.PLLQ = 9;
+  if (HAL_RCC_OscConfig(&RCC_OscInitStruct) != HAL_OK)
+  {
+    Error_Handler();
+  }
+  /**Activate the Over-Drive mode 
+  */
+  if (HAL_PWREx_EnableOverDrive() != HAL_OK)
+  {
+    Error_Handler();
+  }
+  /**Initializes the CPU, AHB and APB busses clocks 
+  */
+  RCC_ClkInitStruct.ClockType = RCC_CLOCKTYPE_HCLK|RCC_CLOCKTYPE_SYSCLK
+                              |RCC_CLOCKTYPE_PCLK1|RCC_CLOCKTYPE_PCLK2;
+  RCC_ClkInitStruct.SYSCLKSource = RCC_SYSCLKSOURCE_PLLCLK;
+  RCC_ClkInitStruct.AHBCLKDivider = RCC_SYSCLK_DIV1;
+  RCC_ClkInitStruct.APB1CLKDivider = RCC_HCLK_DIV4;
+  RCC_ClkInitStruct.APB2CLKDivider = RCC_HCLK_DIV2;
+
+  if (HAL_RCC_ClockConfig(&RCC_ClkInitStruct, FLASH_LATENCY_7) != HAL_OK)
+  {
+    Error_Handler();
+  }
+  PeriphClkInitStruct.PeriphClockSelection = RCC_PERIPHCLK_USART3|RCC_PERIPHCLK_CLK48;
+  PeriphClkInitStruct.Usart3ClockSelection = RCC_USART3CLKSOURCE_PCLK1;
+  PeriphClkInitStruct.Clk48ClockSelection = RCC_CLK48SOURCE_PLL;
+  if (HAL_RCCEx_PeriphCLKConfig(&PeriphClkInitStruct) != HAL_OK)
+  {
+    Error_Handler();
+  }
+}
+

bsp/stm32/stm32f767-st-nucleo/board/board.h

@@ -0,0 +1,41 @@
+/*
+ * Copyright (c) 2006-2018, RT-Thread Development Team
+ *
+ * SPDX-License-Identifier: Apache-2.0
+ *
+ * Change Logs:
+ * Date           Author       Notes
+ * 2018-11-5      SummerGift   change to new framework
+ * 2019-1-10      e31207077    change to new framework
+ */
+
+#ifndef __BOARD_H__
+#define __BOARD_H__
+
+#include <rtthread.h>
+#include <stm32f7xx.h>
+#include "drv_common.h"
+
+#define STM32_FLASH_START_ADRESS     ((uint32_t)0x08000000)
+#define STM32_FLASH_SIZE             (2048 * 1024)
+#define STM32_FLASH_END_ADDRESS      ((uint32_t)(STM32_FLASH_START_ADRESS + STM32_FLASH_SIZE))
+
+#define STM32_SRAM_SIZE           (512)
+#define STM32_SRAM_END            (0x20000000 + STM32_SRAM_SIZE * 1024)
+
+#if defined(__CC_ARM) || defined(__CLANG_ARM)
+extern int Image$$RW_IRAM1$$ZI$$Limit;
+#define HEAP_BEGIN      (&Image$$RW_IRAM1$$ZI$$Limit)
+#elif __ICCARM__
+#pragma section="CSTACK"
+#define HEAP_BEGIN      (__segment_end("CSTACK"))
+#else
+extern int __bss_end;
+#define HEAP_BEGIN      (&__bss_end)
+#endif
+
+#define HEAP_END        STM32_SRAM_END
+
+void SystemClock_Config(void);
+
+#endif

bsp/stm32/stm32f767-st-nucleo/board/linker_scripts/link.icf

@@ -0,0 +1,28 @@
+/*###ICF### Section handled by ICF editor, don't touch! ****/
+/*-Editor annotation file-*/
+/* IcfEditorFile="$TOOLKIT_DIR$\config\ide\IcfEditor\cortex_v1_0.xml" */
+/*-Specials-*/
+define symbol __ICFEDIT_intvec_start__ = 0x08000000;
+/*-Memory Regions-*/
+define symbol __ICFEDIT_region_ROM_start__ = 0x08000000;
+define symbol __ICFEDIT_region_ROM_end__   = 0x081FFFFF;
+define symbol __ICFEDIT_region_RAM_start__ = 0x20000000;
+define symbol __ICFEDIT_region_RAM_end__   = 0x2007FFFF;
+/*-Sizes-*/
+define symbol __ICFEDIT_size_cstack__ = 0x0400;
+define symbol __ICFEDIT_size_heap__   = 0x0000;
+/**** End of ICF editor section. ###ICF###*/
+
+define memory mem with size = 4G;
+define region ROM_region      = mem:[from __ICFEDIT_region_ROM_start__   to __ICFEDIT_region_ROM_end__];
+define region RAM_region      = mem:[from __ICFEDIT_region_RAM_start__   to __ICFEDIT_region_RAM_end__];
+
+define block CSTACK    with alignment = 8, size = __ICFEDIT_size_cstack__   { };
+
+initialize by copy { readwrite };
+do not initialize  { section .noinit };
+
+place at address mem:__ICFEDIT_intvec_start__ { readonly section .intvec };
+
+place in ROM_region   { readonly };
+place in RAM_region   { readwrite, last block CSTACK};

bsp/stm32/stm32f767-st-nucleo/board/linker_scripts/link.lds

@@ -0,0 +1,144 @@
+/*
+ * linker script for STM32F4xx with GNU ld
+ * bernard.xiong 2009-10-14
+ */
+
+/* Program Entry, set to mark it as "used" and avoid gc */
+MEMORY
+{
+    ROM (rx) : ORIGIN = 0x08000000, LENGTH = 2048k /* 2048KB flash */
+    RAM (rw) : ORIGIN = 0x20000000, LENGTH =  512k /* 512K sram */
+}
+ENTRY(Reset_Handler)
+_system_stack_size = 0x200;
+
+SECTIONS
+{
+    .text :
+    {
+        . = ALIGN(4);
+        _stext = .;
+        KEEP(*(.isr_vector))            /* Startup code */
+
+        . = ALIGN(4);
+        *(.text)                        /* remaining code */
+        *(.text.*)                      /* remaining code */
+        *(.rodata)                      /* read-only data (constants) */
+        *(.rodata*)
+        *(.glue_7)
+        *(.glue_7t)
+        *(.gnu.linkonce.t*)
+
+        /* section information for finsh shell */
+        . = ALIGN(4);
+        __fsymtab_start = .;
+        KEEP(*(FSymTab))
+        __fsymtab_end = .;
+
+        . = ALIGN(4);
+        __vsymtab_start = .;
+        KEEP(*(VSymTab))
+        __vsymtab_end = .;
+
+        /* section information for initial. */
+        . = ALIGN(4);
+        __rt_init_start = .;
+        KEEP(*(SORT(.rti_fn*)))
+        __rt_init_end = .;
+
+        . = ALIGN(4);
+        _etext = .;
+    } > ROM = 0
+
+    /* .ARM.exidx is sorted, so has to go in its own output section.  */
+    __exidx_start = .;
+    .ARM.exidx :
+    {
+        *(.ARM.exidx* .gnu.linkonce.armexidx.*)
+
+        /* This is used by the startup in order to initialize the .data secion */
+        _sidata = .;
+    } > ROM
+    __exidx_end = .;
+
+    /* .data section which is used for initialized data */
+
+    .data : AT (_sidata)
+    {
+        . = ALIGN(4);
+        /* This is used by the startup in order to initialize the .data secion */
+        _sdata = . ;
+
+        *(.data)
+        *(.data.*)
+        *(.gnu.linkonce.d*)
+
+        . = ALIGN(4);
+        /* This is used by the startup in order to initialize the .data secion */
+        _edata = . ;
+    } >RAM
+
+    .stack : 
+    {
+        . = ALIGN(4);
+        _sstack = .;
+        . = . + _system_stack_size;
+        . = ALIGN(4);
+        _estack = .;
+    } >RAM
+
+    __bss_start = .;
+    .bss :
+    {
+        . = ALIGN(4);
+        /* This is used by the startup in order to initialize the .bss secion */
+        _sbss = .;
+
+        *(.bss)
+        *(.bss.*)
+        *(COMMON)
+
+        . = ALIGN(4);
+        /* This is used by the startup in order to initialize the .bss secion */
+        _ebss = . ;
+        
+        *(.bss.init)
+    } > RAM
+    __bss_end = .;
+
+    _end = .;
+
+    /* Stabs debugging sections.  */
+    .stab          0 : { *(.stab) }
+    .stabstr       0 : { *(.stabstr) }
+    .stab.excl     0 : { *(.stab.excl) }
+    .stab.exclstr  0 : { *(.stab.exclstr) }
+    .stab.index    0 : { *(.stab.index) }
+    .stab.indexstr 0 : { *(.stab.indexstr) }
+    .comment       0 : { *(.comment) }
+    /* DWARF debug sections.
+     * Symbols in the DWARF debugging sections are relative to the beginning
+     * of the section so we begin them at 0.  */
+    /* DWARF 1 */
+    .debug          0 : { *(.debug) }
+    .line           0 : { *(.line) }
+    /* GNU DWARF 1 extensions */
+    .debug_srcinfo  0 : { *(.debug_srcinfo) }
+    .debug_sfnames  0 : { *(.debug_sfnames) }
+    /* DWARF 1.1 and DWARF 2 */
+    .debug_aranges  0 : { *(.debug_aranges) }
+    .debug_pubnames 0 : { *(.debug_pubnames) }
+    /* DWARF 2 */
+    .debug_info     0 : { *(.debug_info .gnu.linkonce.wi.*) }
+    .debug_abbrev   0 : { *(.debug_abbrev) }
+    .debug_line     0 : { *(.debug_line) }
+    .debug_frame    0 : { *(.debug_frame) }
+    .debug_str      0 : { *(.debug_str) }
+    .debug_loc      0 : { *(.debug_loc) }
+    .debug_macinfo  0 : { *(.debug_macinfo) }
+    /* SGI/MIPS DWARF 2 extensions */
+    .debug_weaknames 0 : { *(.debug_weaknames) }
+    .debug_funcnames 0 : { *(.debug_funcnames) }
+    .debug_typenames 0 : { *(.debug_typenames) }
+    .debug_varnames  0 : { *(.debug_varnames) }
+}

bsp/stm32/stm32f767-st-nucleo/board/linker_scripts/link.sct

@@ -0,0 +1,15 @@
+; *************************************************************
+; *** Scatter-Loading Description File generated by uVision ***
+; *************************************************************
+
+LR_IROM1 0x08000000 0x00200000  {    ; load region size_region
+  ER_IROM1 0x08000000 0x00200000  {  ; load address = execution address
+   *.o (RESET, +First)
+   *(InRoot$$Sections)
+   .ANY (+RO)
+  }
+  RW_IRAM1 0x20020000 0x00080000  {  ; RW data
+   .ANY (+RW +ZI)
+  }
+}
+

bsp/stm32/stm32f767-st-nucleo/project.eww

@@ -0,0 +1,10 @@
+<?xml version="1.0" encoding="iso-8859-1"?>
+
+<workspace>
+  <project>
+    <path>$WS_DIR$\project.ewp</path>
+  </project>
+  <batchBuild/>
+</workspace>
+
+

bsp/stm32/stm32f767-st-nucleo/project.uvprojx

@@ -0,0 +1,851 @@
+<?xml version="1.0" encoding="UTF-8" standalone="no" ?>
+<Project xmlns:xsi="http://www.w3.org/2001/XMLSchema-instance" xsi:noNamespaceSchemaLocation="project_projx.xsd">
+
+  <SchemaVersion>2.1</SchemaVersion>
+
+  <Header>### uVision Project, (C) Keil Software</Header>
+
+  <Targets>
+    <Target>
+      <TargetName>rt-thread</TargetName>
+      <ToolsetNumber>0x4</ToolsetNumber>
+      <ToolsetName>ARM-ADS</ToolsetName>
+      <pCCUsed>5060750::V5.06 update 6 (build 750)::ARMCC</pCCUsed>
+      <uAC6>0</uAC6>
+      <TargetOption>
+        <TargetCommonOption>
+          <Device>STM32F767ZITx</Device>
+          <Vendor>STMicroelectronics</Vendor>
+          <PackID>Keil.STM32F7xx_DFP.2.11.0</PackID>
+          <PackURL>http://www.keil.com/pack</PackURL>
+          <Cpu>IRAM(0x20020000,0x60000) IRAM2(0x20000000,0x20000) IROM(0x08000000,0x200000) IROM2(0x00200000,0x200000) CPUTYPE("Cortex-M7") FPU3(DFPU) CLOCK(12000000) ELITTLE</Cpu>
+          <FlashUtilSpec></FlashUtilSpec>
+          <StartupFile></StartupFile>
+          <FlashDriverDll>UL2CM3(-S0 -C0 -P0 -FD20020000 -FC1000 -FN2 -FF0STM32F7x_2048 -FS08000000 -FL0200000 -FF1STM32F7xTCM_2048 -FS1200000 -FL1200000 -FP0($$Device:STM32F767ZITx$CMSIS\Flash\STM32F7x_2048.FLM) -FP1($$Device:STM32F767ZITx$CMSIS\Flash\STM32F7xTCM_2048.FLM))</FlashDriverDll>
+          <DeviceId>0</DeviceId>
+          <RegisterFile>$$Device:STM32F767ZITx$Drivers\CMSIS\Device\ST\STM32F7xx\Include\stm32f7xx.h</RegisterFile>
+          <MemoryEnv></MemoryEnv>
+          <Cmp></Cmp>
+          <Asm></Asm>
+          <Linker></Linker>
+          <OHString></OHString>
+          <InfinionOptionDll></InfinionOptionDll>
+          <SLE66CMisc></SLE66CMisc>
+          <SLE66AMisc></SLE66AMisc>
+          <SLE66LinkerMisc></SLE66LinkerMisc>
+          <SFDFile>$$Device:STM32F767ZITx$CMSIS\SVD\STM32F7x7_v1r2.svd</SFDFile>
+          <bCustSvd>0</bCustSvd>
+          <UseEnv>0</UseEnv>
+          <BinPath></BinPath>
+          <IncludePath></IncludePath>
+          <LibPath></LibPath>
+          <RegisterFilePath></RegisterFilePath>
+          <DBRegisterFilePath></DBRegisterFilePath>
+          <TargetStatus>
+            <Error>0</Error>
+            <ExitCodeStop>0</ExitCodeStop>
+            <ButtonStop>0</ButtonStop>
+            <NotGenerated>0</NotGenerated>
+            <InvalidFlash>1</InvalidFlash>
+          </TargetStatus>
+          <OutputDirectory>.\build\keil\Obj\</OutputDirectory>
+          <OutputName>rt-thread</OutputName>
+          <CreateExecutable>1</CreateExecutable>
+          <CreateLib>0</CreateLib>
+          <CreateHexFile>0</CreateHexFile>
+          <DebugInformation>1</DebugInformation>
+          <BrowseInformation>1</BrowseInformation>
+          <ListingPath>.\build\keil\List\</ListingPath>
+          <HexFormatSelection>1</HexFormatSelection>
+          <Merge32K>0</Merge32K>
+          <CreateBatchFile>0</CreateBatchFile>
+          <BeforeCompile>
+            <RunUserProg1>0</RunUserProg1>
+            <RunUserProg2>0</RunUserProg2>
+            <UserProg1Name></UserProg1Name>
+            <UserProg2Name></UserProg2Name>
+            <UserProg1Dos16Mode>0</UserProg1Dos16Mode>
+            <UserProg2Dos16Mode>0</UserProg2Dos16Mode>
+            <nStopU1X>0</nStopU1X>
+            <nStopU2X>0</nStopU2X>
+          </BeforeCompile>
+          <BeforeMake>
+            <RunUserProg1>0</RunUserProg1>
+            <RunUserProg2>0</RunUserProg2>
+            <UserProg1Name></UserProg1Name>
+            <UserProg2Name></UserProg2Name>
+            <UserProg1Dos16Mode>0</UserProg1Dos16Mode>
+            <UserProg2Dos16Mode>0</UserProg2Dos16Mode>
+            <nStopB1X>0</nStopB1X>
+            <nStopB2X>0</nStopB2X>
+          </BeforeMake>
+          <AfterMake>
+            <RunUserProg1>1</RunUserProg1>
+            <RunUserProg2>0</RunUserProg2>
+            <UserProg1Name>fromelf --bin !L --output rtthread.bin</UserProg1Name>
+            <UserProg2Name></UserProg2Name>
+            <UserProg1Dos16Mode>0</UserProg1Dos16Mode>
+            <UserProg2Dos16Mode>0</UserProg2Dos16Mode>
+            <nStopA1X>0</nStopA1X>
+            <nStopA2X>0</nStopA2X>
+          </AfterMake>
+          <SelectedForBatchBuild>0</SelectedForBatchBuild>
+          <SVCSIdString></SVCSIdString>
+        </TargetCommonOption>
+        <CommonProperty>
+          <UseCPPCompiler>0</UseCPPCompiler>
+          <RVCTCodeConst>0</RVCTCodeConst>
+          <RVCTZI>0</RVCTZI>
+          <RVCTOtherData>0</RVCTOtherData>
+          <ModuleSelection>0</ModuleSelection>
+          <IncludeInBuild>1</IncludeInBuild>
+          <AlwaysBuild>0</AlwaysBuild>
+          <GenerateAssemblyFile>0</GenerateAssemblyFile>
+          <AssembleAssemblyFile>0</AssembleAssemblyFile>
+          <PublicsOnly>0</PublicsOnly>
+          <StopOnExitCode>3</StopOnExitCode>
+          <CustomArgument></CustomArgument>
+          <IncludeLibraryModules></IncludeLibraryModules>
+          <ComprImg>1</ComprImg>
+        </CommonProperty>
+        <DllOption>
+          <SimDllName>SARMCM3.DLL</SimDllName>
+          <SimDllArguments> -REMAP -MPU</SimDllArguments>
+          <SimDlgDll>DCM.DLL</SimDlgDll>
+          <SimDlgDllArguments>-pCM7</SimDlgDllArguments>
+          <TargetDllName>SARMCM3.DLL</TargetDllName>
+          <TargetDllArguments> -MPU</TargetDllArguments>
+          <TargetDlgDll>TCM.DLL</TargetDlgDll>
+          <TargetDlgDllArguments>-pCM7</TargetDlgDllArguments>
+        </DllOption>
+        <DebugOption>
+          <OPTHX>
+            <HexSelection>1</HexSelection>
+            <HexRangeLowAddress>0</HexRangeLowAddress>
+            <HexRangeHighAddress>0</HexRangeHighAddress>
+            <HexOffset>0</HexOffset>
+            <Oh166RecLen>16</Oh166RecLen>
+          </OPTHX>
+        </DebugOption>
+        <Utilities>
+          <Flash1>
+            <UseTargetDll>1</UseTargetDll>
+            <UseExternalTool>0</UseExternalTool>
+            <RunIndependent>0</RunIndependent>
+            <UpdateFlashBeforeDebugging>1</UpdateFlashBeforeDebugging>
+            <Capability>1</Capability>
+            <DriverSelection>4096</DriverSelection>
+          </Flash1>
+          <bUseTDR>1</bUseTDR>
+          <Flash2>BIN\UL2CM3.DLL</Flash2>
+          <Flash3></Flash3>
+          <Flash4></Flash4>
+          <pFcarmOut></pFcarmOut>
+          <pFcarmGrp></pFcarmGrp>
+          <pFcArmRoot></pFcArmRoot>
+          <FcArmLst>0</FcArmLst>
+        </Utilities>
+        <TargetArmAds>
+          <ArmAdsMisc>
+            <GenerateListings>0</GenerateListings>
+            <asHll>1</asHll>
+            <asAsm>1</asAsm>
+            <asMacX>1</asMacX>
+            <asSyms>1</asSyms>
+            <asFals>1</asFals>
+            <asDbgD>1</asDbgD>
+            <asForm>1</asForm>
+            <ldLst>0</ldLst>
+            <ldmm>1</ldmm>
+            <ldXref>1</ldXref>
+            <BigEnd>0</BigEnd>
+            <AdsALst>1</AdsALst>
+            <AdsACrf>1</AdsACrf>
+            <AdsANop>0</AdsANop>
+            <AdsANot>0</AdsANot>
+            <AdsLLst>1</AdsLLst>
+            <AdsLmap>1</AdsLmap>
+            <AdsLcgr>1</AdsLcgr>
+            <AdsLsym>1</AdsLsym>
+            <AdsLszi>1</AdsLszi>
+            <AdsLtoi>1</AdsLtoi>
+            <AdsLsun>1</AdsLsun>
+            <AdsLven>1</AdsLven>
+            <AdsLsxf>1</AdsLsxf>
+            <RvctClst>0</RvctClst>
+            <GenPPlst>0</GenPPlst>
+            <AdsCpuType>"Cortex-M7"</AdsCpuType>
+            <RvctDeviceName></RvctDeviceName>
+            <mOS>0</mOS>
+            <uocRom>0</uocRom>
+            <uocRam>0</uocRam>
+            <hadIROM>1</hadIROM>
+            <hadIRAM>1</hadIRAM>
+            <hadXRAM>0</hadXRAM>
+            <uocXRam>0</uocXRam>
+            <RvdsVP>3</RvdsVP>
+            <hadIRAM2>1</hadIRAM2>
+            <hadIROM2>1</hadIROM2>
+            <StupSel>8</StupSel>
+            <useUlib>0</useUlib>
+            <EndSel>0</EndSel>
+            <uLtcg>0</uLtcg>
+            <nSecure>0</nSecure>
+            <RoSelD>4</RoSelD>
+            <RwSelD>4</RwSelD>
+            <CodeSel>0</CodeSel>
+            <OptFeed>0</OptFeed>
+            <NoZi1>0</NoZi1>
+            <NoZi2>0</NoZi2>
+            <NoZi3>0</NoZi3>
+            <NoZi4>0</NoZi4>
+            <NoZi5>0</NoZi5>
+            <Ro1Chk>0</Ro1Chk>
+            <Ro2Chk>0</Ro2Chk>
+            <Ro3Chk>0</Ro3Chk>
+            <Ir1Chk>1</Ir1Chk>
+            <Ir2Chk>0</Ir2Chk>
+            <Ra1Chk>0</Ra1Chk>
+            <Ra2Chk>0</Ra2Chk>
+            <Ra3Chk>0</Ra3Chk>
+            <Im1Chk>1</Im1Chk>
+            <Im2Chk>1</Im2Chk>
+            <OnChipMemories>
+              <Ocm1>
+                <Type>0</Type>
+                <StartAddress>0x0</StartAddress>
+                <Size>0x0</Size>
+              </Ocm1>
+              <Ocm2>
+                <Type>0</Type>
+                <StartAddress>0x0</StartAddress>
+                <Size>0x0</Size>
+              </Ocm2>
+              <Ocm3>
+                <Type>0</Type>
+                <StartAddress>0x0</StartAddress>
+                <Size>0x0</Size>
+              </Ocm3>
+              <Ocm4>
+                <Type>0</Type>
+                <StartAddress>0x0</StartAddress>
+                <Size>0x0</Size>
+              </Ocm4>
+              <Ocm5>
+                <Type>0</Type>
+                <StartAddress>0x0</StartAddress>
+                <Size>0x0</Size>
+              </Ocm5>
+              <Ocm6>
+                <Type>0</Type>
+                <StartAddress>0x0</StartAddress>
+                <Size>0x0</Size>
+              </Ocm6>
+              <IRAM>
+                <Type>0</Type>
+                <StartAddress>0x20020000</StartAddress>
+                <Size>0x60000</Size>
+              </IRAM>
+              <IROM>
+                <Type>1</Type>
+                <StartAddress>0x8000000</StartAddress>
+                <Size>0x200000</Size>
+              </IROM>
+              <XRAM>
+                <Type>0</Type>
+                <StartAddress>0x0</StartAddress>
+                <Size>0x0</Size>
+              </XRAM>
+              <OCR_RVCT1>
+                <Type>1</Type>
+                <StartAddress>0x0</StartAddress>
+                <Size>0x0</Size>
+              </OCR_RVCT1>
+              <OCR_RVCT2>
+                <Type>1</Type>
+                <StartAddress>0x0</StartAddress>
+                <Size>0x0</Size>
+              </OCR_RVCT2>
+              <OCR_RVCT3>
+                <Type>1</Type>
+                <StartAddress>0x0</StartAddress>
+                <Size>0x0</Size>
+              </OCR_RVCT3>
+              <OCR_RVCT4>
+                <Type>1</Type>
+                <StartAddress>0x8000000</StartAddress>
+                <Size>0x200000</Size>
+              </OCR_RVCT4>
+              <OCR_RVCT5>
+                <Type>1</Type>
+                <StartAddress>0x200000</StartAddress>
+                <Size>0x200000</Size>
+              </OCR_RVCT5>
+              <OCR_RVCT6>
+                <Type>0</Type>
+                <StartAddress>0x0</StartAddress>
+                <Size>0x0</Size>
+              </OCR_RVCT6>
+              <OCR_RVCT7>
+                <Type>0</Type>
+                <StartAddress>0x0</StartAddress>
+                <Size>0x0</Size>
+              </OCR_RVCT7>
+              <OCR_RVCT8>
+                <Type>0</Type>
+                <StartAddress>0x0</StartAddress>
+                <Size>0x0</Size>
+              </OCR_RVCT8>
+              <OCR_RVCT9>
+                <Type>0</Type>
+                <StartAddress>0x20020000</StartAddress>
+                <Size>0x60000</Size>
+              </OCR_RVCT9>
+              <OCR_RVCT10>
+                <Type>0</Type>
+                <StartAddress>0x20000000</StartAddress>
+                <Size>0x20000</Size>
+              </OCR_RVCT10>
+            </OnChipMemories>
+            <RvctStartVector></RvctStartVector>
+          </ArmAdsMisc>
+          <Cads>
+            <interw>1</interw>
+            <Optim>1</Optim>
+            <oTime>0</oTime>
+            <SplitLS>0</SplitLS>
+            <OneElfS>1</OneElfS>
+            <Strict>0</Strict>
+            <EnumInt>0</EnumInt>
+            <PlainCh>0</PlainCh>
+            <Ropi>0</Ropi>
+            <Rwpi>0</Rwpi>
+            <wLevel>2</wLevel>
+            <uThumb>0</uThumb>
+            <uSurpInc>0</uSurpInc>
+            <uC99>1</uC99>
+            <uGnu>0</uGnu>
+            <useXO>0</useXO>
+            <v6Lang>1</v6Lang>
+            <v6LangP>1</v6LangP>
+            <vShortEn>1</vShortEn>
+            <vShortWch>1</vShortWch>
+            <v6Lto>0</v6Lto>
+            <v6WtE>0</v6WtE>
+            <v6Rtti>0</v6Rtti>
+            <VariousControls>
+              <MiscControls></MiscControls>
+              <Define>STM32F767xx, USE_HAL_DRIVER, RT_USING_ARM_LIBC</Define>
+              <Undefine></Undefine>
+              <IncludePath>applications;.;board;board\CubeMX_Config\Inc;..\libraries\HAL_Drivers;..\libraries\HAL_Drivers\config;..\..\..\include;..\..\..\libcpu\arm\cortex-m7;..\..\..\libcpu\arm\common;..\..\..\components\dfs\include;..\..\..\components\dfs\filesystems\devfs;..\..\..\components\drivers\include;..\..\..\components\drivers\include;..\..\..\components\drivers\include;..\..\..\components\finsh;..\..\..\components\libc\compilers\armlibc;..\..\..\components\libc\compilers\common;..\libraries\STM32F7xx_HAL\STM32F7xx_HAL_Driver\Inc;..\libraries\STM32F7xx_HAL\CMSIS\Device\ST\STM32F7xx\Include;..\libraries\STM32F7xx_HAL\CMSIS\Include</IncludePath>
+            </VariousControls>
+          </Cads>
+          <Aads>
+            <interw>1</interw>
+            <Ropi>0</Ropi>
+            <Rwpi>0</Rwpi>
+            <thumb>0</thumb>
+            <SplitLS>0</SplitLS>
+            <SwStkChk>0</SwStkChk>
+            <NoWarn>0</NoWarn>
+            <uSurpInc>0</uSurpInc>
+            <useXO>0</useXO>
+            <uClangAs>0</uClangAs>
+            <VariousControls>
+              <MiscControls></MiscControls>
+              <Define></Define>
+              <Undefine></Undefine>
+              <IncludePath></IncludePath>
+            </VariousControls>
+          </Aads>
+          <LDads>
+            <umfTarg>0</umfTarg>
+            <Ropi>0</Ropi>
+            <Rwpi>0</Rwpi>
+            <noStLib>0</noStLib>
+            <RepFail>1</RepFail>
+            <useFile>0</useFile>
+            <TextAddressRange>0x08000000</TextAddressRange>
+            <DataAddressRange>0x20000000</DataAddressRange>
+            <pXoBase></pXoBase>
+            <ScatterFile>.\board\linker_scripts\link.sct</ScatterFile>
+            <IncludeLibs></IncludeLibs>
+            <IncludeLibsPath></IncludeLibsPath>
+            <Misc> --keep *.o(.rti_fn.*)   --keep *.o(FSymTab) --keep *.o(VSymTab) </Misc>
+            <LinkerInputFile></LinkerInputFile>
+            <DisabledWarnings></DisabledWarnings>
+          </LDads>
+        </TargetArmAds>
+      </TargetOption>
+      <Groups>
+        <Group>
+          <GroupName>Applications</GroupName>
+          <Files>
+            <File>
+              <FileName>main.c</FileName>
+              <FileType>1</FileType>
+              <FilePath>applications\main.c</FilePath>
+            </File>
+          </Files>
+        </Group>
+        <Group>
+          <GroupName>Drivers</GroupName>
+          <Files>
+            <File>
+              <FileName>board.c</FileName>
+              <FileType>1</FileType>
+              <FilePath>board\board.c</FilePath>
+            </File>
+            <File>
+              <FileName>stm32f7xx_hal_msp.c</FileName>
+              <FileType>1</FileType>
+              <FilePath>board\CubeMX_Config\Src\stm32f7xx_hal_msp.c</FilePath>
+            </File>
+            <File>
+              <FileName>startup_stm32f767xx.s</FileName>
+              <FileType>2</FileType>
+              <FilePath>..\libraries\STM32F7xx_HAL\CMSIS\Device\ST\STM32F7xx\Source\Templates\arm\startup_stm32f767xx.s</FilePath>
+            </File>
+            <File>
+              <FileName>drv_gpio.c</FileName>
+              <FileType>1</FileType>
+              <FilePath>..\libraries\HAL_Drivers\drv_gpio.c</FilePath>
+            </File>
+            <File>
+              <FileName>drv_usart.c</FileName>
+              <FileType>1</FileType>
+              <FilePath>..\libraries\HAL_Drivers\drv_usart.c</FilePath>
+            </File>
+            <File>
+              <FileName>drv_common.c</FileName>
+              <FileType>1</FileType>
+              <FilePath>..\libraries\HAL_Drivers\drv_common.c</FilePath>
+            </File>
+          </Files>
+        </Group>
+        <Group>
+          <GroupName>Kernel</GroupName>
+          <Files>
+            <File>
+              <FileName>clock.c</FileName>
+              <FileType>1</FileType>
+              <FilePath>..\..\..\src\clock.c</FilePath>
+            </File>
+            <File>
+              <FileName>components.c</FileName>
+              <FileType>1</FileType>
+              <FilePath>..\..\..\src\components.c</FilePath>
+            </File>
+            <File>
+              <FileName>cpu.c</FileName>
+              <FileType>1</FileType>
+              <FilePath>..\..\..\src\cpu.c</FilePath>
+            </File>
+            <File>
+              <FileName>device.c</FileName>
+              <FileType>1</FileType>
+              <FilePath>..\..\..\src\device.c</FilePath>
+            </File>
+            <File>
+              <FileName>idle.c</FileName>
+              <FileType>1</FileType>
+              <FilePath>..\..\..\src\idle.c</FilePath>
+            </File>
+            <File>
+              <FileName>ipc.c</FileName>
+              <FileType>1</FileType>
+              <FilePath>..\..\..\src\ipc.c</FilePath>
+            </File>
+            <File>
+              <FileName>irq.c</FileName>
+              <FileType>1</FileType>
+              <FilePath>..\..\..\src\irq.c</FilePath>
+            </File>
+            <File>
+              <FileName>kservice.c</FileName>
+              <FileType>1</FileType>
+              <FilePath>..\..\..\src\kservice.c</FilePath>
+            </File>
+            <File>
+              <FileName>mem.c</FileName>
+              <FileType>1</FileType>
+              <FilePath>..\..\..\src\mem.c</FilePath>
+            </File>
+            <File>
+              <FileName>mempool.c</FileName>
+              <FileType>1</FileType>
+              <FilePath>..\..\..\src\mempool.c</FilePath>
+            </File>
+            <File>
+              <FileName>object.c</FileName>
+              <FileType>1</FileType>
+              <FilePath>..\..\..\src\object.c</FilePath>
+            </File>
+            <File>
+              <FileName>scheduler.c</FileName>
+              <FileType>1</FileType>
+              <FilePath>..\..\..\src\scheduler.c</FilePath>
+            </File>
+            <File>
+              <FileName>signal.c</FileName>
+              <FileType>1</FileType>
+              <FilePath>..\..\..\src\signal.c</FilePath>
+            </File>
+            <File>
+              <FileName>thread.c</FileName>
+              <FileType>1</FileType>
+              <FilePath>..\..\..\src\thread.c</FilePath>
+            </File>
+            <File>
+              <FileName>timer.c</FileName>
+              <FileType>1</FileType>
+              <FilePath>..\..\..\src\timer.c</FilePath>
+            </File>
+          </Files>
+        </Group>
+        <Group>
+          <GroupName>CORTEX-M7</GroupName>
+          <Files>
+            <File>
+              <FileName>cpuport.c</FileName>
+              <FileType>1</FileType>
+              <FilePath>..\..\..\libcpu\arm\cortex-m7\cpuport.c</FilePath>
+            </File>
+            <File>
+              <FileName>context_rvds.S</FileName>
+              <FileType>2</FileType>
+              <FilePath>..\..\..\libcpu\arm\cortex-m7\context_rvds.S</FilePath>
+            </File>
+            <File>
+              <FileName>backtrace.c</FileName>
+              <FileType>1</FileType>
+              <FilePath>..\..\..\libcpu\arm\common\backtrace.c</FilePath>
+            </File>
+            <File>
+              <FileName>div0.c</FileName>
+              <FileType>1</FileType>
+              <FilePath>..\..\..\libcpu\arm\common\div0.c</FilePath>
+            </File>
+            <File>
+              <FileName>showmem.c</FileName>
+              <FileType>1</FileType>
+              <FilePath>..\..\..\libcpu\arm\common\showmem.c</FilePath>
+            </File>
+          </Files>
+        </Group>
+        <Group>
+          <GroupName>Filesystem</GroupName>
+          <Files>
+            <File>
+              <FileName>dfs.c</FileName>
+              <FileType>1</FileType>
+              <FilePath>..\..\..\components\dfs\src\dfs.c</FilePath>
+            </File>
+            <File>
+              <FileName>dfs_file.c</FileName>
+              <FileType>1</FileType>
+              <FilePath>..\..\..\components\dfs\src\dfs_file.c</FilePath>
+            </File>
+            <File>
+              <FileName>dfs_fs.c</FileName>
+              <FileType>1</FileType>
+              <FilePath>..\..\..\components\dfs\src\dfs_fs.c</FilePath>
+            </File>
+            <File>
+              <FileName>dfs_posix.c</FileName>
+              <FileType>1</FileType>
+              <FilePath>..\..\..\components\dfs\src\dfs_posix.c</FilePath>
+            </File>
+            <File>
+              <FileName>poll.c</FileName>
+              <FileType>1</FileType>
+              <FilePath>..\..\..\components\dfs\src\poll.c</FilePath>
+            </File>
+            <File>
+              <FileName>select.c</FileName>
+              <FileType>1</FileType>
+              <FilePath>..\..\..\components\dfs\src\select.c</FilePath>
+            </File>
+            <File>
+              <FileName>devfs.c</FileName>
+              <FileType>1</FileType>
+              <FilePath>..\..\..\components\dfs\filesystems\devfs\devfs.c</FilePath>
+            </File>
+          </Files>
+        </Group>
+        <Group>
+          <GroupName>DeviceDrivers</GroupName>
+          <Files>
+            <File>
+              <FileName>pin.c</FileName>
+              <FileType>1</FileType>
+              <FilePath>..\..\..\components\drivers\misc\pin.c</FilePath>
+            </File>
+            <File>
+              <FileName>serial.c</FileName>
+              <FileType>1</FileType>
+              <FilePath>..\..\..\components\drivers\serial\serial.c</FilePath>
+            </File>
+            <File>
+              <FileName>completion.c</FileName>
+              <FileType>1</FileType>
+              <FilePath>..\..\..\components\drivers\src\completion.c</FilePath>
+            </File>
+            <File>
+              <FileName>dataqueue.c</FileName>
+              <FileType>1</FileType>
+              <FilePath>..\..\..\components\drivers\src\dataqueue.c</FilePath>
+            </File>
+            <File>
+              <FileName>pipe.c</FileName>
+              <FileType>1</FileType>
+              <FilePath>..\..\..\components\drivers\src\pipe.c</FilePath>
+            </File>
+            <File>
+              <FileName>ringblk_buf.c</FileName>
+              <FileType>1</FileType>
+              <FilePath>..\..\..\components\drivers\src\ringblk_buf.c</FilePath>
+            </File>
+            <File>
+              <FileName>ringbuffer.c</FileName>
+              <FileType>1</FileType>
+              <FilePath>..\..\..\components\drivers\src\ringbuffer.c</FilePath>
+            </File>
+            <File>
+              <FileName>waitqueue.c</FileName>
+              <FileType>1</FileType>
+              <FilePath>..\..\..\components\drivers\src\waitqueue.c</FilePath>
+            </File>
+            <File>
+              <FileName>workqueue.c</FileName>
+              <FileType>1</FileType>
+              <FilePath>..\..\..\components\drivers\src\workqueue.c</FilePath>
+            </File>
+          </Files>
+        </Group>
+        <Group>
+          <GroupName>finsh</GroupName>
+          <Files>
+            <File>
+              <FileName>shell.c</FileName>
+              <FileType>1</FileType>
+              <FilePath>..\..\..\components\finsh\shell.c</FilePath>
+            </File>
+            <File>
+              <FileName>symbol.c</FileName>
+              <FileType>1</FileType>
+              <FilePath>..\..\..\components\finsh\symbol.c</FilePath>
+            </File>
+            <File>
+              <FileName>cmd.c</FileName>
+              <FileType>1</FileType>
+              <FilePath>..\..\..\components\finsh\cmd.c</FilePath>
+            </File>
+            <File>
+              <FileName>msh.c</FileName>
+              <FileType>1</FileType>
+              <FilePath>..\..\..\components\finsh\msh.c</FilePath>
+            </File>
+            <File>
+              <FileName>msh_cmd.c</FileName>
+              <FileType>1</FileType>
+              <FilePath>..\..\..\components\finsh\msh_cmd.c</FilePath>
+            </File>
+            <File>
+              <FileName>msh_file.c</FileName>
+              <FileType>1</FileType>
+              <FilePath>..\..\..\components\finsh\msh_file.c</FilePath>
+            </File>
+            <File>
+              <FileName>finsh_compiler.c</FileName>
+              <FileType>1</FileType>
+              <FilePath>..\..\..\components\finsh\finsh_compiler.c</FilePath>
+            </File>
+            <File>
+              <FileName>finsh_error.c</FileName>
+              <FileType>1</FileType>
+              <FilePath>..\..\..\components\finsh\finsh_error.c</FilePath>
+            </File>
+            <File>
+              <FileName>finsh_heap.c</FileName>
+              <FileType>1</FileType>
+              <FilePath>..\..\..\components\finsh\finsh_heap.c</FilePath>
+            </File>
+            <File>
+              <FileName>finsh_init.c</FileName>
+              <FileType>1</FileType>
+              <FilePath>..\..\..\components\finsh\finsh_init.c</FilePath>
+            </File>
+            <File>
+              <FileName>finsh_node.c</FileName>
+              <FileType>1</FileType>
+              <FilePath>..\..\..\components\finsh\finsh_node.c</FilePath>
+            </File>
+            <File>
+              <FileName>finsh_ops.c</FileName>
+              <FileType>1</FileType>
+              <FilePath>..\..\..\components\finsh\finsh_ops.c</FilePath>
+            </File>
+            <File>
+              <FileName>finsh_parser.c</FileName>
+              <FileType>1</FileType>
+              <FilePath>..\..\..\components\finsh\finsh_parser.c</FilePath>
+            </File>
+            <File>
+              <FileName>finsh_var.c</FileName>
+              <FileType>1</FileType>
+              <FilePath>..\..\..\components\finsh\finsh_var.c</FilePath>
+            </File>
+            <File>
+              <FileName>finsh_vm.c</FileName>
+              <FileType>1</FileType>
+              <FilePath>..\..\..\components\finsh\finsh_vm.c</FilePath>
+            </File>
+            <File>
+              <FileName>finsh_token.c</FileName>
+              <FileType>1</FileType>
+              <FilePath>..\..\..\components\finsh\finsh_token.c</FilePath>
+            </File>
+          </Files>
+        </Group>
+        <Group>
+          <GroupName>libc</GroupName>
+          <Files>
+            <File>
+              <FileName>libc.c</FileName>
+              <FileType>1</FileType>
+              <FilePath>..\..\..\components\libc\compilers\armlibc\libc.c</FilePath>
+            </File>
+            <File>
+              <FileName>mem_std.c</FileName>
+              <FileType>1</FileType>
+              <FilePath>..\..\..\components\libc\compilers\armlibc\mem_std.c</FilePath>
+            </File>
+            <File>
+              <FileName>stdio.c</FileName>
+              <FileType>1</FileType>
+              <FilePath>..\..\..\components\libc\compilers\armlibc\stdio.c</FilePath>
+            </File>
+            <File>
+              <FileName>stubs.c</FileName>
+              <FileType>1</FileType>
+              <FilePath>..\..\..\components\libc\compilers\armlibc\stubs.c</FilePath>
+            </File>
+            <File>
+              <FileName>time.c</FileName>
+              <FileType>1</FileType>
+              <FilePath>..\..\..\components\libc\compilers\armlibc\time.c</FilePath>
+            </File>
+            <File>
+              <FileName>gmtime_r.c</FileName>
+              <FileType>1</FileType>
+              <FilePath>..\..\..\components\libc\compilers\common\gmtime_r.c</FilePath>
+            </File>
+          </Files>
+        </Group>
+        <Group>
+          <GroupName>STM32_HAL</GroupName>
+          <Files>
+            <File>
+              <FileName>system_stm32f7xx.c</FileName>
+              <FileType>1</FileType>
+              <FilePath>..\libraries\STM32F7xx_HAL\CMSIS\Device\ST\STM32F7xx\Source\Templates\system_stm32f7xx.c</FilePath>
+            </File>
+            <File>
+              <FileName>stm32f7xx_hal.c</FileName>
+              <FileType>1</FileType>
+              <FilePath>..\libraries\STM32F7xx_HAL\STM32F7xx_HAL_Driver\Src\stm32f7xx_hal.c</FilePath>
+            </File>
+            <File>
+              <FileName>stm32f7xx_hal_cec.c</FileName>
+              <FileType>1</FileType>
+              <FilePath>..\libraries\STM32F7xx_HAL\STM32F7xx_HAL_Driver\Src\stm32f7xx_hal_cec.c</FilePath>
+            </File>
+            <File>
+              <FileName>stm32f7xx_hal_cortex.c</FileName>
+              <FileType>1</FileType>
+              <FilePath>..\libraries\STM32F7xx_HAL\STM32F7xx_HAL_Driver\Src\stm32f7xx_hal_cortex.c</FilePath>
+            </File>
+            <File>
+              <FileName>stm32f7xx_hal_crc.c</FileName>
+              <FileType>1</FileType>
+              <FilePath>..\libraries\STM32F7xx_HAL\STM32F7xx_HAL_Driver\Src\stm32f7xx_hal_crc.c</FilePath>
+            </File>
+            <File>
+              <FileName>stm32f7xx_hal_cryp.c</FileName>
+              <FileType>1</FileType>
+              <FilePath>..\libraries\STM32F7xx_HAL\STM32F7xx_HAL_Driver\Src\stm32f7xx_hal_cryp.c</FilePath>
+            </File>
+            <File>
+              <FileName>stm32f7xx_hal_cryp_ex.c</FileName>
+              <FileType>1</FileType>
+              <FilePath>..\libraries\STM32F7xx_HAL\STM32F7xx_HAL_Driver\Src\stm32f7xx_hal_cryp_ex.c</FilePath>
+            </File>
+            <File>
+              <FileName>stm32f7xx_hal_dma.c</FileName>
+              <FileType>1</FileType>
+              <FilePath>..\libraries\STM32F7xx_HAL\STM32F7xx_HAL_Driver\Src\stm32f7xx_hal_dma.c</FilePath>
+            </File>
+            <File>
+              <FileName>stm32f7xx_hal_dma_ex.c</FileName>
+              <FileType>1</FileType>
+              <FilePath>..\libraries\STM32F7xx_HAL\STM32F7xx_HAL_Driver\Src\stm32f7xx_hal_dma_ex.c</FilePath>
+            </File>
+            <File>
+              <FileName>stm32f7xx_hal_pwr.c</FileName>
+              <FileType>1</FileType>
+              <FilePath>..\libraries\STM32F7xx_HAL\STM32F7xx_HAL_Driver\Src\stm32f7xx_hal_pwr.c</FilePath>
+            </File>
+            <File>
+              <FileName>stm32f7xx_hal_pwr_ex.c</FileName>
+              <FileType>1</FileType>
+              <FilePath>..\libraries\STM32F7xx_HAL\STM32F7xx_HAL_Driver\Src\stm32f7xx_hal_pwr_ex.c</FilePath>
+            </File>
+            <File>
+              <FileName>stm32f7xx_hal_rcc.c</FileName>
+              <FileType>1</FileType>
+              <FilePath>..\libraries\STM32F7xx_HAL\STM32F7xx_HAL_Driver\Src\stm32f7xx_hal_rcc.c</FilePath>
+            </File>
+            <File>
+              <FileName>stm32f7xx_hal_rcc_ex.c</FileName>
+              <FileType>1</FileType>
+              <FilePath>..\libraries\STM32F7xx_HAL\STM32F7xx_HAL_Driver\Src\stm32f7xx_hal_rcc_ex.c</FilePath>
+            </File>
+            <File>
+              <FileName>stm32f7xx_hal_rng.c</FileName>
+              <FileType>1</FileType>
+              <FilePath>..\libraries\STM32F7xx_HAL\STM32F7xx_HAL_Driver\Src\stm32f7xx_hal_rng.c</FilePath>
+            </File>
+            <File>
+              <FileName>stm32f7xx_hal_sram.c</FileName>
+              <FileType>1</FileType>
+              <FilePath>..\libraries\STM32F7xx_HAL\STM32F7xx_HAL_Driver\Src\stm32f7xx_hal_sram.c</FilePath>
+            </File>
+            <File>
+              <FileName>stm32f7xx_hal_gpio.c</FileName>
+              <FileType>1</FileType>
+              <FilePath>..\libraries\STM32F7xx_HAL\STM32F7xx_HAL_Driver\Src\stm32f7xx_hal_gpio.c</FilePath>
+            </File>
+            <File>
+              <FileName>stm32f7xx_hal_uart.c</FileName>
+              <FileType>1</FileType>
+              <FilePath>..\libraries\STM32F7xx_HAL\STM32F7xx_HAL_Driver\Src\stm32f7xx_hal_uart.c</FilePath>
+            </File>
+            <File>
+              <FileName>stm32f7xx_hal_usart.c</FileName>
+              <FileType>1</FileType>
+              <FilePath>..\libraries\STM32F7xx_HAL\STM32F7xx_HAL_Driver\Src\stm32f7xx_hal_usart.c</FilePath>
+            </File>
+          </Files>
+        </Group>
+      </Groups>
+    </Target>
+  </Targets>
+
+  <RTE>
+    <apis/>
+    <components/>
+    <files/>
+  </RTE>
+
+</Project>

bsp/stm32/stm32f767-st-nucleo/rtconfig.h

@@ -0,0 +1,186 @@
+#ifndef RT_CONFIG_H__
+#define RT_CONFIG_H__
+
+/* Automatically generated file; DO NOT EDIT. */
+/* RT-Thread Configuration */
+
+/* RT-Thread Kernel */
+
+#define RT_NAME_MAX 8
+#define RT_ALIGN_SIZE 4
+#define RT_THREAD_PRIORITY_32
+#define RT_THREAD_PRIORITY_MAX 32
+#define RT_TICK_PER_SECOND 100
+#define RT_USING_OVERFLOW_CHECK
+#define RT_USING_HOOK
+#define RT_USING_IDLE_HOOK
+#define RT_IDEL_HOOK_LIST_SIZE 4
+#define IDLE_THREAD_STACK_SIZE 256
+#define RT_DEBUG
+
+/* Inter-Thread communication */
+
+#define RT_USING_SEMAPHORE
+#define RT_USING_MUTEX
+#define RT_USING_EVENT
+#define RT_USING_MAILBOX
+#define RT_USING_MESSAGEQUEUE
+
+/* Memory Management */
+
+#define RT_USING_MEMPOOL
+#define RT_USING_SMALL_MEM
+#define RT_USING_HEAP
+
+/* Kernel Device Object */
+
+#define RT_USING_DEVICE
+#define RT_USING_CONSOLE
+#define RT_CONSOLEBUF_SIZE 128
+#define RT_CONSOLE_DEVICE_NAME "uart3"
+#define RT_VER_NUM 0x40000
+#define ARCH_ARM
+#define ARCH_ARM_CORTEX_M
+#define ARCH_ARM_CORTEX_M7
+
+/* RT-Thread Components */
+
+#define RT_USING_COMPONENTS_INIT
+#define RT_USING_USER_MAIN
+#define RT_MAIN_THREAD_STACK_SIZE 2048
+#define RT_MAIN_THREAD_PRIORITY 10
+
+/* C++ features */
+
+
+/* Command shell */
+
+#define RT_USING_FINSH
+#define FINSH_THREAD_NAME "tshell"
+#define FINSH_USING_HISTORY
+#define FINSH_HISTORY_LINES 5
+#define FINSH_USING_SYMTAB
+#define FINSH_USING_DESCRIPTION
+#define FINSH_THREAD_PRIORITY 20
+#define FINSH_THREAD_STACK_SIZE 4096
+#define FINSH_CMD_SIZE 80
+#define FINSH_USING_MSH
+#define FINSH_USING_MSH_DEFAULT
+#define FINSH_ARG_MAX 10
+
+/* Device virtual file system */
+
+#define RT_USING_DFS
+#define DFS_USING_WORKDIR
+#define DFS_FILESYSTEMS_MAX 2
+#define DFS_FILESYSTEM_TYPES_MAX 2
+#define DFS_FD_MAX 16
+#define RT_USING_DFS_DEVFS
+
+/* Device Drivers */
+
+#define RT_USING_DEVICE_IPC
+#define RT_PIPE_BUFSZ 512
+#define RT_USING_SERIAL
+#define RT_SERIAL_USING_DMA
+#define RT_USING_PIN
+
+/* Using WiFi */
+
+
+/* Using USB */
+
+
+/* POSIX layer and C standard library */
+
+#define RT_USING_LIBC
+#define RT_USING_POSIX
+
+/* Network */
+
+/* Socket abstraction layer */
+
+
+/* light weight TCP/IP stack */
+
+
+/* Modbus master and slave stack */
+
+
+/* AT commands */
+
+
+/* VBUS(Virtual Software BUS) */
+
+
+/* Utilities */
+
+
+/* ARM CMSIS */
+
+
+/* RT-Thread online packages */
+
+/* IoT - internet of things */
+
+
+/* Wi-Fi */
+
+/* Marvell WiFi */
+
+
+/* Wiced WiFi */
+
+
+/* IoT Cloud */
+
+
+/* security packages */
+
+
+/* language packages */
+
+
+/* multimedia packages */
+
+
+/* tools packages */
+
+
+/* system packages */
+
+
+/* peripheral libraries and drivers */
+
+
+/* miscellaneous packages */
+
+
+/* sample package */
+
+/* samples: kernel and components samples */
+
+
+/* example package: hello */
+
+#define SOC_FAMILY_STM32
+#define SOC_SERIES_STM32F7
+
+/* Hardware Drivers Config */
+
+#define SOC_STM32F767ZI
+
+/* Onboard Peripheral Drivers */
+
+#define BSP_USING_USB_TO_USART
+
+/* On-chip Peripheral Drivers */
+
+#define BSP_USING_GPIO
+#define BSP_USING_UART
+#define BSP_USING_UART3
+
+/* Board extended module Drivers */
+
+
+#endif

bsp/stm32/stm32f767-st-nucleo/rtconfig.py

@@ -0,0 +1,144 @@
+import os
+
+# toolchains options
+ARCH='arm'
+CPU='cortex-m7'
+CROSS_TOOL='gcc'
+
+if os.getenv('RTT_CC'):
+    CROSS_TOOL = os.getenv('RTT_CC')
+if os.getenv('RTT_ROOT'):
+    RTT_ROOT = os.getenv('RTT_ROOT')
+
+# cross_tool provides the cross compiler
+# EXEC_PATH is the compiler execute path, for example, CodeSourcery, Keil MDK, IAR
+if  CROSS_TOOL == 'gcc':
+    PLATFORM 	= 'gcc'
+    EXEC_PATH 	= '/usr/local/Cellar/arm-none-eabi-gcc/7-2017-q4-major/gcc/bin/'
+elif CROSS_TOOL == 'keil':
+    PLATFORM 	= 'armcc'
+    EXEC_PATH 	= r'C:/Keil_v5'
+elif CROSS_TOOL == 'iar':
+	PLATFORM 	= 'iar'
+	EXEC_PATH 	= r'C:/Program Files (x86)/IAR Systems/Embedded Workbench 8.0'
+
+if os.getenv('RTT_EXEC_PATH'):
+    EXEC_PATH = os.getenv('RTT_EXEC_PATH')
+
+BUILD = 'debug'
+
+if PLATFORM == 'gcc':
+    # toolchains
+    PREFIX = 'arm-none-eabi-'
+    CC = PREFIX + 'gcc'
+    CXX = PREFIX + 'g++'
+    AS = PREFIX + 'gcc'
+    AR = PREFIX + 'ar'
+    CXX = PREFIX + 'g++'
+    LINK = PREFIX + 'gcc'
+    TARGET_EXT = 'elf'
+    SIZE = PREFIX + 'size'
+    OBJDUMP = PREFIX + 'objdump'
+    OBJCPY = PREFIX + 'objcopy'
+    STRIP = PREFIX + 'strip'
+
+    DEVICE = ' -mcpu=' + CPU + ' -mthumb -mfpu=fpv5-d16 -mfloat-abi=hard -ffunction-sections -fdata-sections'
+    CFLAGS = DEVICE + ' -std=c99 -g -Wall'
+    AFLAGS = ' -c' + DEVICE + ' -x assembler-with-cpp -Wa,-mimplicit-it=thumb '
+    LFLAGS = DEVICE + ' -Wl,--gc-sections,-Map=rtthread.map,-cref,-u,Reset_Handler -T board/linker_scripts/link.lds'
+
+    CPATH = ''
+    LPATH = ''
+
+    if BUILD == 'debug':
+        CFLAGS += ' -O0 -gdwarf-2'
+        AFLAGS += ' -gdwarf-2'
+    else:
+        CFLAGS += ' -O2 -Os'
+
+    POST_ACTION = OBJCPY + ' -O binary $TARGET rtthread.bin\n' + SIZE + ' $TARGET \n'
+
+    # module setting 
+    CXXFLAGS = ' -Woverloaded-virtual -fno-exceptions -fno-rtti '
+    M_CFLAGS = CFLAGS + ' -mlong-calls -fPIC '
+    M_CXXFLAGS = CXXFLAGS + ' -mlong-calls -fPIC'
+    M_LFLAGS = DEVICE + CXXFLAGS + ' -Wl,--gc-sections,-z,max-page-size=0x4' +\
+                                    ' -shared -fPIC -nostartfiles -static-libgcc'
+    M_POST_ACTION = STRIP + ' -R .hash $TARGET\n' + SIZE + ' $TARGET \n'
+
+elif PLATFORM == 'armcc':
+    # toolchains
+    CC = 'armcc'
+    CXX = 'armcc'
+    AS = 'armasm'
+    AR = 'armar'
+    LINK = 'armlink'
+    TARGET_EXT = 'axf'
+
+    DEVICE = ' --cpu Cortex-M7.fp.sp --fpu=FPv4-SP'
+    CFLAGS = DEVICE + ' --apcs=interwork '
+    AFLAGS = DEVICE
+    LFLAGS = DEVICE + ' --info sizes --info totals --info unused --info veneers --list rtthread.map --scatter rtthread.sct'
+
+    CFLAGS += ' -I' + EXEC_PATH + '/ARM/ARMCC/INC'
+    LFLAGS += ' --libpath "' + EXEC_PATH + '/ARM/ARMCC/lib"'
+
+    EXEC_PATH += '/arm/bin40/'
+
+    if BUILD == 'debug':
+        CFLAGS += ' -g -O0'
+        AFLAGS += ' -g'
+    else:
+        CFLAGS += ' -O2 -Otime'
+
+    CXXFLAGS = CFLAGS
+    POST_ACTION = 'fromelf --bin $TARGET --output rtthread.bin \nfromelf -z $TARGET'
+
+elif PLATFORM == 'iar':
+    # toolchains
+    CC = 'iccarm'
+    CXX = 'iccarm'
+    AS = 'iasmarm'
+    AR = 'iarchive'
+    LINK = 'ilinkarm'
+    TARGET_EXT = 'out'
+
+    DEVICE = ''
+
+    CFLAGS = DEVICE
+    CFLAGS += ' --diag_suppress Pa050'
+    CFLAGS += ' --no_cse' 
+    CFLAGS += ' --no_unroll' 
+    CFLAGS += ' --no_inline' 
+    CFLAGS += ' --no_code_motion' 
+    CFLAGS += ' --no_tbaa' 
+    CFLAGS += ' --no_clustering' 
+    CFLAGS += ' --no_scheduling' 
+    CFLAGS += ' --debug' 
+    CFLAGS += ' --endian=little' 
+    CFLAGS += ' --cpu=Cortex-M7' 
+    CFLAGS += ' -e' 
+    CFLAGS += ' --fpu=None'
+    CFLAGS += ' --dlib_config "' + EXEC_PATH + '/arm/INC/c/DLib_Config_Normal.h"'    
+    CFLAGS += ' -Ol'    
+    CFLAGS += ' --use_c++_inline'
+    CFLAGS += ' --silent'
+    
+    AFLAGS = ''
+    AFLAGS += ' -s+' 
+    AFLAGS += ' -w+' 
+    AFLAGS += ' -r' 
+    AFLAGS += ' --cpu Cortex-M7' 
+    AFLAGS += ' --fpu None' 
+    AFLAGS += ' -S' 
+    
+    LFLAGS = ' --config rtthread.icf'
+    LFLAGS += ' --redirect _Printf=_PrintfTiny' 
+    LFLAGS += ' --redirect _Scanf=_ScanfSmall' 
+    LFLAGS += ' --entry __iar_program_start'    
+    LFLAGS += ' --silent'
+
+    CXXFLAGS = CFLAGS
+
+    EXEC_PATH = EXEC_PATH + '/arm/bin/'
+    POST_ACTION = ''

bsp/stm32/stm32f767-st-nucleo/template.eww

@@ -0,0 +1,10 @@
+<?xml version="1.0" encoding="iso-8859-1"?>
+
+<workspace>
+  <project>
+    <path>$WS_DIR$\template.ewp</path>
+  </project>
+  <batchBuild/>
+</workspace>
+
+

bsp/stm32/stm32f767-st-nucleo/template.uvoptx

@@ -0,0 +1,196 @@
+<?xml version="1.0" encoding="UTF-8" standalone="no" ?>
+<ProjectOpt xmlns:xsi="http://www.w3.org/2001/XMLSchema-instance" xsi:noNamespaceSchemaLocation="project_optx.xsd">
+
+  <SchemaVersion>1.0</SchemaVersion>
+
+  <Header>### uVision Project, (C) Keil Software</Header>
+
+  <Extensions>
+    <cExt>*.c</cExt>
+    <aExt>*.s*; *.src; *.a*</aExt>
+    <oExt>*.obj; *.o</oExt>
+    <lExt>*.lib</lExt>
+    <tExt>*.txt; *.h; *.inc</tExt>
+    <pExt>*.plm</pExt>
+    <CppX>*.cpp</CppX>
+    <nMigrate>0</nMigrate>
+  </Extensions>
+
+  <DaveTm>
+    <dwLowDateTime>0</dwLowDateTime>
+    <dwHighDateTime>0</dwHighDateTime>
+  </DaveTm>
+
+  <Target>
+    <TargetName>rt-thread</TargetName>
+    <ToolsetNumber>0x4</ToolsetNumber>
+    <ToolsetName>ARM-ADS</ToolsetName>
+    <TargetOption>
+      <CLKADS>12000000</CLKADS>
+      <OPTTT>
+        <gFlags>1</gFlags>
+        <BeepAtEnd>1</BeepAtEnd>
+        <RunSim>0</RunSim>
+        <RunTarget>1</RunTarget>
+        <RunAbUc>0</RunAbUc>
+      </OPTTT>
+      <OPTHX>
+        <HexSelection>1</HexSelection>
+        <FlashByte>65535</FlashByte>
+        <HexRangeLowAddress>0</HexRangeLowAddress>
+        <HexRangeHighAddress>0</HexRangeHighAddress>
+        <HexOffset>0</HexOffset>
+      </OPTHX>
+      <OPTLEX>
+        <PageWidth>79</PageWidth>
+        <PageLength>66</PageLength>
+        <TabStop>8</TabStop>
+        <ListingPath>.\build\keil\List\</ListingPath>
+      </OPTLEX>
+      <ListingPage>
+        <CreateCListing>1</CreateCListing>
+        <CreateAListing>1</CreateAListing>
+        <CreateLListing>1</CreateLListing>
+        <CreateIListing>0</CreateIListing>
+        <AsmCond>1</AsmCond>
+        <AsmSymb>1</AsmSymb>
+        <AsmXref>0</AsmXref>
+        <CCond>1</CCond>
+        <CCode>0</CCode>
+        <CListInc>0</CListInc>
+        <CSymb>0</CSymb>
+        <LinkerCodeListing>0</LinkerCodeListing>
+      </ListingPage>
+      <OPTXL>
+        <LMap>1</LMap>
+        <LComments>1</LComments>
+        <LGenerateSymbols>1</LGenerateSymbols>
+        <LLibSym>1</LLibSym>
+        <LLines>1</LLines>
+        <LLocSym>1</LLocSym>
+        <LPubSym>1</LPubSym>
+        <LXref>0</LXref>
+        <LExpSel>0</LExpSel>
+      </OPTXL>
+      <OPTFL>
+        <tvExp>1</tvExp>
+        <tvExpOptDlg>0</tvExpOptDlg>
+        <IsCurrentTarget>1</IsCurrentTarget>
+      </OPTFL>
+      <CpuCode>18</CpuCode>
+      <DebugOpt>
+        <uSim>0</uSim>
+        <uTrg>1</uTrg>
+        <sLdApp>1</sLdApp>
+        <sGomain>1</sGomain>
+        <sRbreak>1</sRbreak>
+        <sRwatch>1</sRwatch>
+        <sRmem>1</sRmem>
+        <sRfunc>1</sRfunc>
+        <sRbox>1</sRbox>
+        <tLdApp>1</tLdApp>
+        <tGomain>1</tGomain>
+        <tRbreak>1</tRbreak>
+        <tRwatch>1</tRwatch>
+        <tRmem>1</tRmem>
+        <tRfunc>0</tRfunc>
+        <tRbox>1</tRbox>
+        <tRtrace>1</tRtrace>
+        <sRSysVw>1</sRSysVw>
+        <tRSysVw>1</tRSysVw>
+        <sRunDeb>0</sRunDeb>
+        <sLrtime>0</sLrtime>
+        <bEvRecOn>1</bEvRecOn>
+        <bSchkAxf>0</bSchkAxf>
+        <bTchkAxf>0</bTchkAxf>
+        <nTsel>6</nTsel>
+        <sDll></sDll>
+        <sDllPa></sDllPa>
+        <sDlgDll></sDlgDll>
+        <sDlgPa></sDlgPa>
+        <sIfile></sIfile>
+        <tDll></tDll>
+        <tDllPa></tDllPa>
+        <tDlgDll></tDlgDll>
+        <tDlgPa></tDlgPa>
+        <tIfile></tIfile>
+        <pMon>STLink\ST-LINKIII-KEIL_SWO.dll</pMon>
+      </DebugOpt>
+      <TargetDriverDllRegistry>
+        <SetRegEntry>
+          <Number>0</Number>
+          <Key>ST-LINKIII-KEIL_SWO</Key>
+          <Name>-U066FFF544852707267192022 -O206 -SF4000 -C0 -A0 -I0 -HNlocalhost -HP7184 -P2 -N00("ARM CoreSight SW-DP") -D00(5BA02477) -L00(0) -TO18 -TC10000000 -TP21 -TDS8007 -TDT0 -TDC1F -TIEFFFFFFFF -TIP8 -FO7 -FD20020000 -FC1000 -FN2 -FF0STM32F7x_2048.FLM -FS08000000 -FL0200000 -FP0($$Device:STM32F767ZITx$CMSIS\Flash\STM32F7x_2048.FLM) -FF1STM32F7xTCM_2048.FLM -FS1200000 -FL1200000 -FP1($$Device:STM32F767ZITx$CMSIS\Flash\STM32F7xTCM_2048.FLM)</Name>
+        </SetRegEntry>
+        <SetRegEntry>
+          <Number>0</Number>
+          <Key>UL2CM3</Key>
+          <Name>UL2CM3(-S0 -C0 -P0 ) -FN2 -FC1000 -FD20020000 -FF0STM32F7x_2048 -FF1STM32F7xTCM_2048 -FL0200000 -FL1200000 -FS08000000 -FS1200000 -FP0($$Device:STM32F767ZITx$CMSIS\Flash\STM32F7x_2048.FLM) -FP1($$Device:STM32F767ZITx$CMSIS\Flash\STM32F7xTCM_2048.FLM)</Name>
+        </SetRegEntry>
+        <SetRegEntry>
+          <Number>0</Number>
+          <Key>JL2CM3</Key>
+          <Name>-U59400616 -O78 -S2 -ZTIFSpeedSel5000 -A0 -C0 -JU1 -JI127.0.0.1 -JP0 -RST0 -TO18 -TC10000000 -TP21 -TDS8001 -TDT0 -TDC1F -TIEFFFFFFFF -TIP8 -TB1 -TFE0 -FO15 -FD20000000 -FC1000 -FN1 -FF0STM32F4xx_1024.FLM -FS08000000 -FL0100000 -FP0($$Device:STM32F407ZGTx$CMSIS\Flash\STM32F4xx_1024.FLM)</Name>
+        </SetRegEntry>
+      </TargetDriverDllRegistry>
+      <Breakpoint/>
+      <Tracepoint>
+        <THDelay>0</THDelay>
+      </Tracepoint>
+      <DebugFlag>
+        <trace>0</trace>
+        <periodic>0</periodic>
+        <aLwin>0</aLwin>
+        <aCover>0</aCover>
+        <aSer1>0</aSer1>
+        <aSer2>0</aSer2>
+        <aPa>0</aPa>
+        <viewmode>0</viewmode>
+        <vrSel>0</vrSel>
+        <aSym>0</aSym>
+        <aTbox>0</aTbox>
+        <AscS1>0</AscS1>
+        <AscS2>0</AscS2>
+        <AscS3>0</AscS3>
+        <aSer3>0</aSer3>
+        <eProf>0</eProf>
+        <aLa>0</aLa>
+        <aPa1>0</aPa1>
+        <AscS4>0</AscS4>
+        <aSer4>0</aSer4>
+        <StkLoc>0</StkLoc>
+        <TrcWin>0</TrcWin>
+        <newCpu>0</newCpu>
+        <uProt>0</uProt>
+      </DebugFlag>
+      <LintExecutable></LintExecutable>
+      <LintConfigFile></LintConfigFile>
+      <bLintAuto>0</bLintAuto>
+      <bAutoGenD>0</bAutoGenD>
+      <LntExFlags>0</LntExFlags>
+      <pMisraName></pMisraName>
+      <pszMrule></pszMrule>
+      <pSingCmds></pSingCmds>
+      <pMultCmds></pMultCmds>
+      <pMisraNamep></pMisraNamep>
+      <pszMrulep></pszMrulep>
+      <pSingCmdsp></pSingCmdsp>
+      <pMultCmdsp></pMultCmdsp>
+      <DebugDescription>
+        <Enable>1</Enable>
+        <EnableLog>0</EnableLog>
+        <Protocol>2</Protocol>
+        <DbgClock>10000000</DbgClock>
+      </DebugDescription>
+    </TargetOption>
+  </Target>
+
+  <Group>
+    <GroupName>Source Group 1</GroupName>
+    <tvExp>0</tvExp>
+    <tvExpOptDlg>0</tvExpOptDlg>
+    <cbSel>0</cbSel>
+    <RteFlg>0</RteFlg>
+  </Group>
+
+</ProjectOpt>

bsp/stm32/stm32f767-st-nucleo/template.uvprojx

@@ -0,0 +1,394 @@
+<?xml version="1.0" encoding="UTF-8" standalone="no" ?>
+<Project xmlns:xsi="http://www.w3.org/2001/XMLSchema-instance" xsi:noNamespaceSchemaLocation="project_projx.xsd">
+
+  <SchemaVersion>2.1</SchemaVersion>
+
+  <Header>### uVision Project, (C) Keil Software</Header>
+
+  <Targets>
+    <Target>
+      <TargetName>rt-thread</TargetName>
+      <ToolsetNumber>0x4</ToolsetNumber>
+      <ToolsetName>ARM-ADS</ToolsetName>
+      <pCCUsed>5060750::V5.06 update 6 (build 750)::ARMCC</pCCUsed>
+      <uAC6>0</uAC6>
+      <TargetOption>
+        <TargetCommonOption>
+          <Device>STM32F767ZITx</Device>
+          <Vendor>STMicroelectronics</Vendor>
+          <PackID>Keil.STM32F7xx_DFP.2.11.0</PackID>
+          <PackURL>http://www.keil.com/pack</PackURL>
+          <Cpu>IRAM(0x20020000,0x60000) IRAM2(0x20000000,0x20000) IROM(0x08000000,0x200000) IROM2(0x00200000,0x200000) CPUTYPE("Cortex-M7") FPU3(DFPU) CLOCK(12000000) ELITTLE</Cpu>
+          <FlashUtilSpec></FlashUtilSpec>
+          <StartupFile></StartupFile>
+          <FlashDriverDll>UL2CM3(-S0 -C0 -P0 -FD20020000 -FC1000 -FN2 -FF0STM32F7x_2048 -FS08000000 -FL0200000 -FF1STM32F7xTCM_2048 -FS1200000 -FL1200000 -FP0($$Device:STM32F767ZITx$CMSIS\Flash\STM32F7x_2048.FLM) -FP1($$Device:STM32F767ZITx$CMSIS\Flash\STM32F7xTCM_2048.FLM))</FlashDriverDll>
+          <DeviceId>0</DeviceId>
+          <RegisterFile>$$Device:STM32F767ZITx$Drivers\CMSIS\Device\ST\STM32F7xx\Include\stm32f7xx.h</RegisterFile>
+          <MemoryEnv></MemoryEnv>
+          <Cmp></Cmp>
+          <Asm></Asm>
+          <Linker></Linker>
+          <OHString></OHString>
+          <InfinionOptionDll></InfinionOptionDll>
+          <SLE66CMisc></SLE66CMisc>
+          <SLE66AMisc></SLE66AMisc>
+          <SLE66LinkerMisc></SLE66LinkerMisc>
+          <SFDFile>$$Device:STM32F767ZITx$CMSIS\SVD\STM32F7x7_v1r2.svd</SFDFile>
+          <bCustSvd>0</bCustSvd>
+          <UseEnv>0</UseEnv>
+          <BinPath></BinPath>
+          <IncludePath></IncludePath>
+          <LibPath></LibPath>
+          <RegisterFilePath></RegisterFilePath>
+          <DBRegisterFilePath></DBRegisterFilePath>
+          <TargetStatus>
+            <Error>0</Error>
+            <ExitCodeStop>0</ExitCodeStop>
+            <ButtonStop>0</ButtonStop>
+            <NotGenerated>0</NotGenerated>
+            <InvalidFlash>1</InvalidFlash>
+          </TargetStatus>
+          <OutputDirectory>.\build\keil\Obj\</OutputDirectory>
+          <OutputName>rt-thread</OutputName>
+          <CreateExecutable>1</CreateExecutable>
+          <CreateLib>0</CreateLib>
+          <CreateHexFile>0</CreateHexFile>
+          <DebugInformation>1</DebugInformation>
+          <BrowseInformation>1</BrowseInformation>
+          <ListingPath>.\build\keil\List\</ListingPath>
+          <HexFormatSelection>1</HexFormatSelection>
+          <Merge32K>0</Merge32K>
+          <CreateBatchFile>0</CreateBatchFile>
+          <BeforeCompile>
+            <RunUserProg1>0</RunUserProg1>
+            <RunUserProg2>0</RunUserProg2>
+            <UserProg1Name></UserProg1Name>
+            <UserProg2Name></UserProg2Name>
+            <UserProg1Dos16Mode>0</UserProg1Dos16Mode>
+            <UserProg2Dos16Mode>0</UserProg2Dos16Mode>
+            <nStopU1X>0</nStopU1X>
+            <nStopU2X>0</nStopU2X>
+          </BeforeCompile>
+          <BeforeMake>
+            <RunUserProg1>0</RunUserProg1>
+            <RunUserProg2>0</RunUserProg2>
+            <UserProg1Name></UserProg1Name>
+            <UserProg2Name></UserProg2Name>
+            <UserProg1Dos16Mode>0</UserProg1Dos16Mode>
+            <UserProg2Dos16Mode>0</UserProg2Dos16Mode>
+            <nStopB1X>0</nStopB1X>
+            <nStopB2X>0</nStopB2X>
+          </BeforeMake>
+          <AfterMake>
+            <RunUserProg1>1</RunUserProg1>
+            <RunUserProg2>0</RunUserProg2>
+            <UserProg1Name>fromelf --bin !L --output rtthread.bin</UserProg1Name>
+            <UserProg2Name></UserProg2Name>
+            <UserProg1Dos16Mode>0</UserProg1Dos16Mode>
+            <UserProg2Dos16Mode>0</UserProg2Dos16Mode>
+            <nStopA1X>0</nStopA1X>
+            <nStopA2X>0</nStopA2X>
+          </AfterMake>
+          <SelectedForBatchBuild>0</SelectedForBatchBuild>
+          <SVCSIdString></SVCSIdString>
+        </TargetCommonOption>
+        <CommonProperty>
+          <UseCPPCompiler>0</UseCPPCompiler>
+          <RVCTCodeConst>0</RVCTCodeConst>
+          <RVCTZI>0</RVCTZI>
+          <RVCTOtherData>0</RVCTOtherData>
+          <ModuleSelection>0</ModuleSelection>
+          <IncludeInBuild>1</IncludeInBuild>
+          <AlwaysBuild>0</AlwaysBuild>
+          <GenerateAssemblyFile>0</GenerateAssemblyFile>
+          <AssembleAssemblyFile>0</AssembleAssemblyFile>
+          <PublicsOnly>0</PublicsOnly>
+          <StopOnExitCode>3</StopOnExitCode>
+          <CustomArgument></CustomArgument>
+          <IncludeLibraryModules></IncludeLibraryModules>
+          <ComprImg>1</ComprImg>
+        </CommonProperty>
+        <DllOption>
+          <SimDllName>SARMCM3.DLL</SimDllName>
+          <SimDllArguments> -REMAP -MPU</SimDllArguments>
+          <SimDlgDll>DCM.DLL</SimDlgDll>
+          <SimDlgDllArguments>-pCM7</SimDlgDllArguments>
+          <TargetDllName>SARMCM3.DLL</TargetDllName>
+          <TargetDllArguments> -MPU</TargetDllArguments>
+          <TargetDlgDll>TCM.DLL</TargetDlgDll>
+          <TargetDlgDllArguments>-pCM7</TargetDlgDllArguments>
+        </DllOption>
+        <DebugOption>
+          <OPTHX>
+            <HexSelection>1</HexSelection>
+            <HexRangeLowAddress>0</HexRangeLowAddress>
+            <HexRangeHighAddress>0</HexRangeHighAddress>
+            <HexOffset>0</HexOffset>
+            <Oh166RecLen>16</Oh166RecLen>
+          </OPTHX>
+        </DebugOption>
+        <Utilities>
+          <Flash1>
+            <UseTargetDll>1</UseTargetDll>
+            <UseExternalTool>0</UseExternalTool>
+            <RunIndependent>0</RunIndependent>
+            <UpdateFlashBeforeDebugging>1</UpdateFlashBeforeDebugging>
+            <Capability>1</Capability>
+            <DriverSelection>4096</DriverSelection>
+          </Flash1>
+          <bUseTDR>1</bUseTDR>
+          <Flash2>BIN\UL2CM3.DLL</Flash2>
+          <Flash3></Flash3>
+          <Flash4></Flash4>
+          <pFcarmOut></pFcarmOut>
+          <pFcarmGrp></pFcarmGrp>
+          <pFcArmRoot></pFcArmRoot>
+          <FcArmLst>0</FcArmLst>
+        </Utilities>
+        <TargetArmAds>
+          <ArmAdsMisc>
+            <GenerateListings>0</GenerateListings>
+            <asHll>1</asHll>
+            <asAsm>1</asAsm>
+            <asMacX>1</asMacX>
+            <asSyms>1</asSyms>
+            <asFals>1</asFals>
+            <asDbgD>1</asDbgD>
+            <asForm>1</asForm>
+            <ldLst>0</ldLst>
+            <ldmm>1</ldmm>
+            <ldXref>1</ldXref>
+            <BigEnd>0</BigEnd>
+            <AdsALst>1</AdsALst>
+            <AdsACrf>1</AdsACrf>
+            <AdsANop>0</AdsANop>
+            <AdsANot>0</AdsANot>
+            <AdsLLst>1</AdsLLst>
+            <AdsLmap>1</AdsLmap>
+            <AdsLcgr>1</AdsLcgr>
+            <AdsLsym>1</AdsLsym>
+            <AdsLszi>1</AdsLszi>
+            <AdsLtoi>1</AdsLtoi>
+            <AdsLsun>1</AdsLsun>
+            <AdsLven>1</AdsLven>
+            <AdsLsxf>1</AdsLsxf>
+            <RvctClst>0</RvctClst>
+            <GenPPlst>0</GenPPlst>
+            <AdsCpuType>"Cortex-M7"</AdsCpuType>
+            <RvctDeviceName></RvctDeviceName>
+            <mOS>0</mOS>
+            <uocRom>0</uocRom>
+            <uocRam>0</uocRam>
+            <hadIROM>1</hadIROM>
+            <hadIRAM>1</hadIRAM>
+            <hadXRAM>0</hadXRAM>
+            <uocXRam>0</uocXRam>
+            <RvdsVP>3</RvdsVP>
+            <hadIRAM2>1</hadIRAM2>
+            <hadIROM2>1</hadIROM2>
+            <StupSel>8</StupSel>
+            <useUlib>0</useUlib>
+            <EndSel>0</EndSel>
+            <uLtcg>0</uLtcg>
+            <nSecure>0</nSecure>
+            <RoSelD>4</RoSelD>
+            <RwSelD>4</RwSelD>
+            <CodeSel>0</CodeSel>
+            <OptFeed>0</OptFeed>
+            <NoZi1>0</NoZi1>
+            <NoZi2>0</NoZi2>
+            <NoZi3>0</NoZi3>
+            <NoZi4>0</NoZi4>
+            <NoZi5>0</NoZi5>
+            <Ro1Chk>0</Ro1Chk>
+            <Ro2Chk>0</Ro2Chk>
+            <Ro3Chk>0</Ro3Chk>
+            <Ir1Chk>1</Ir1Chk>
+            <Ir2Chk>0</Ir2Chk>
+            <Ra1Chk>0</Ra1Chk>
+            <Ra2Chk>0</Ra2Chk>
+            <Ra3Chk>0</Ra3Chk>
+            <Im1Chk>1</Im1Chk>
+            <Im2Chk>1</Im2Chk>
+            <OnChipMemories>
+              <Ocm1>
+                <Type>0</Type>
+                <StartAddress>0x0</StartAddress>
+                <Size>0x0</Size>
+              </Ocm1>
+              <Ocm2>
+                <Type>0</Type>
+                <StartAddress>0x0</StartAddress>
+                <Size>0x0</Size>
+              </Ocm2>
+              <Ocm3>
+                <Type>0</Type>
+                <StartAddress>0x0</StartAddress>
+                <Size>0x0</Size>
+              </Ocm3>
+              <Ocm4>
+                <Type>0</Type>
+                <StartAddress>0x0</StartAddress>
+                <Size>0x0</Size>
+              </Ocm4>
+              <Ocm5>
+                <Type>0</Type>
+                <StartAddress>0x0</StartAddress>
+                <Size>0x0</Size>
+              </Ocm5>
+              <Ocm6>
+                <Type>0</Type>
+                <StartAddress>0x0</StartAddress>
+                <Size>0x0</Size>
+              </Ocm6>
+              <IRAM>
+                <Type>0</Type>
+                <StartAddress>0x20020000</StartAddress>
+                <Size>0x60000</Size>
+              </IRAM>
+              <IROM>
+                <Type>1</Type>
+                <StartAddress>0x8000000</StartAddress>
+                <Size>0x200000</Size>
+              </IROM>
+              <XRAM>
+                <Type>0</Type>
+                <StartAddress>0x0</StartAddress>
+                <Size>0x0</Size>
+              </XRAM>
+              <OCR_RVCT1>
+                <Type>1</Type>
+                <StartAddress>0x0</StartAddress>
+                <Size>0x0</Size>
+              </OCR_RVCT1>
+              <OCR_RVCT2>
+                <Type>1</Type>
+                <StartAddress>0x0</StartAddress>
+                <Size>0x0</Size>
+              </OCR_RVCT2>
+              <OCR_RVCT3>
+                <Type>1</Type>
+                <StartAddress>0x0</StartAddress>
+                <Size>0x0</Size>
+              </OCR_RVCT3>
+              <OCR_RVCT4>
+                <Type>1</Type>
+                <StartAddress>0x8000000</StartAddress>
+                <Size>0x200000</Size>
+              </OCR_RVCT4>
+              <OCR_RVCT5>
+                <Type>1</Type>
+                <StartAddress>0x200000</StartAddress>
+                <Size>0x200000</Size>
+              </OCR_RVCT5>
+              <OCR_RVCT6>
+                <Type>0</Type>
+                <StartAddress>0x0</StartAddress>
+                <Size>0x0</Size>
+              </OCR_RVCT6>
+              <OCR_RVCT7>
+                <Type>0</Type>
+                <StartAddress>0x0</StartAddress>
+                <Size>0x0</Size>
+              </OCR_RVCT7>
+              <OCR_RVCT8>
+                <Type>0</Type>
+                <StartAddress>0x0</StartAddress>
+                <Size>0x0</Size>
+              </OCR_RVCT8>
+              <OCR_RVCT9>
+                <Type>0</Type>
+                <StartAddress>0x20020000</StartAddress>
+                <Size>0x60000</Size>
+              </OCR_RVCT9>
+              <OCR_RVCT10>
+                <Type>0</Type>
+                <StartAddress>0x20000000</StartAddress>
+                <Size>0x20000</Size>
+              </OCR_RVCT10>
+            </OnChipMemories>
+            <RvctStartVector></RvctStartVector>
+          </ArmAdsMisc>
+          <Cads>
+            <interw>1</interw>
+            <Optim>1</Optim>
+            <oTime>0</oTime>
+            <SplitLS>0</SplitLS>
+            <OneElfS>1</OneElfS>
+            <Strict>0</Strict>
+            <EnumInt>0</EnumInt>
+            <PlainCh>0</PlainCh>
+            <Ropi>0</Ropi>
+            <Rwpi>0</Rwpi>
+            <wLevel>2</wLevel>
+            <uThumb>0</uThumb>
+            <uSurpInc>0</uSurpInc>
+            <uC99>1</uC99>
+            <uGnu>0</uGnu>
+            <useXO>0</useXO>
+            <v6Lang>1</v6Lang>
+            <v6LangP>1</v6LangP>
+            <vShortEn>1</vShortEn>
+            <vShortWch>1</vShortWch>
+            <v6Lto>0</v6Lto>
+            <v6WtE>0</v6WtE>
+            <v6Rtti>0</v6Rtti>
+            <VariousControls>
+              <MiscControls></MiscControls>
+              <Define></Define>
+              <Undefine></Undefine>
+              <IncludePath></IncludePath>
+            </VariousControls>
+          </Cads>
+          <Aads>
+            <interw>1</interw>
+            <Ropi>0</Ropi>
+            <Rwpi>0</Rwpi>
+            <thumb>0</thumb>
+            <SplitLS>0</SplitLS>
+            <SwStkChk>0</SwStkChk>
+            <NoWarn>0</NoWarn>
+            <uSurpInc>0</uSurpInc>
+            <useXO>0</useXO>
+            <uClangAs>0</uClangAs>
+            <VariousControls>
+              <MiscControls></MiscControls>
+              <Define></Define>
+              <Undefine></Undefine>
+              <IncludePath></IncludePath>
+            </VariousControls>
+          </Aads>
+          <LDads>
+            <umfTarg>0</umfTarg>
+            <Ropi>0</Ropi>
+            <Rwpi>0</Rwpi>
+            <noStLib>0</noStLib>
+            <RepFail>1</RepFail>
+            <useFile>0</useFile>
+            <TextAddressRange>0x08000000</TextAddressRange>
+            <DataAddressRange>0x20000000</DataAddressRange>
+            <pXoBase></pXoBase>
+            <ScatterFile>.\board\linker_scripts\link.sct</ScatterFile>
+            <IncludeLibs></IncludeLibs>
+            <IncludeLibsPath></IncludeLibsPath>
+            <Misc></Misc>
+            <LinkerInputFile></LinkerInputFile>
+            <DisabledWarnings></DisabledWarnings>
+          </LDads>
+        </TargetArmAds>
+      </TargetOption>
+      <Groups>
+        <Group>
+          <GroupName>Source Group 1</GroupName>
+        </Group>
+      </Groups>
+    </Target>
+  </Targets>
+
+  <RTE>
+    <apis/>
+    <components/>
+    <files/>
+  </RTE>
+
+</Project>