rt-thread-official/bsp/imxrt/imxrt1170-nxp-evk/m7/board/Kconfig

menu "Hardware Drivers Config"

config BSP_USING_QSPIFLASH
    bool
    default n

config SOC_MIMXRT1176DVMAA
    bool
    select SOC_MIMXRT1170_SERIES
    select BSP_USING_QSPIFLASH
    select RT_USING_COMPONENTS_INIT
    select RT_USING_USER_MAIN
    default y

menu "On-chip Peripheral Drivers"

    config BSP_USING_DMA
        bool "Enable DMA"
        default n

    config BSP_USING_GPIO
        bool "Enable GPIO"
        select RT_USING_PIN
        default y

    config BSP_USING_RTC
        bool "Enable RTC"
        select RT_USING_RTC
        default n

    config BSP_USING_USB
        bool "Enable USB"
        select RT_USING_USB_HOST
        default n

    if BSP_USING_USB
    config BSP_USB0_HOST
        bool "Enable USB0"
        default n

    config BSP_USB1_HOST
        bool "Enable USB1"
        default n
    endif

    config BSP_USING_SDIO
        bool "Enable SDIO"
        select RT_USING_SDIO
        select RT_USING_DFS
        default n

        if BSP_USING_SDIO
            config CODE_STORED_ON_SDCARD
                bool "Enable Code STORED On SDCARD"
                default n
                help
                    "SD CARD work as boot devive"
        endif

    menuconfig BSP_USING_LPUART
        bool "Enable UART"
        select RT_USING_SERIAL
        default y

        if BSP_USING_LPUART
            config BSP_USING_LPUART1
                bool "Enable LPUART1"
                default y

        config BSP_LPUART1_RX_USING_DMA
            bool "Enable LPUART1 RX DMA"
            depends on BSP_USING_LPUART1
            select BSP_USING_DMA
            select RT_SERIAL_USING_DMA
            default n

        config BSP_LPUART1_RX_DMA_CHANNEL
        depends on BSP_LPUART1_RX_USING_DMA
        int "Set LPUART1 RX DMA channel (0-32)"
        default 0

                config BSP_LPUART1_TX_USING_DMA
                    bool "Enable LPUART1 TX DMA"
                    depends on BSP_USING_LPUART1
                    select BSP_USING_DMA
                    select RT_SERIAL_USING_DMA
                    default n

                    config BSP_LPUART1_TX_DMA_CHANNEL
                        depends on BSP_LPUART1_TX_USING_DMA
                        int "Set LPUART1 TX DMA channel (0-32)"
                        default 1

            config BSP_USING_LPUART3
                bool "Enable LPUART3"
                default n

                config BSP_LPUART3_RX_USING_DMA
                    bool "Enable LPUART3 RX DMA"
                    depends on BSP_USING_LPUART3
                    select BSP_USING_DMA
                    select RT_SERIAL_USING_DMA
                    default n

                    config BSP_LPUART3_RX_DMA_CHANNEL
                        depends on BSP_LPUART3_RX_USING_DMA
                        int "Set LPUART3 RX DMA channel (0-32)"
                        default 0

                config BSP_LPUART3_TX_USING_DMA
                    bool "Enable LPUART3 TX DMA"
                    depends on BSP_USING_LPUART3
                    select BSP_USING_DMA
                    select RT_SERIAL_USING_DMA
                    default n

                    config BSP_LPUART3_TX_DMA_CHANNEL
                        depends on BSP_LPUART3_TX_USING_DMA
                        int "Set LPUART3 TX DMA channel (0-32)"
                        default 1
        endif

        menuconfig BSP_USING_CAN
            bool "Enable CAN"
            select RT_USING_CAN
            default n
            if BSP_USING_CAN
                config BSP_USING_CAN3
                    bool "Enable FLEXCAN3"
                    default n
            endif

        menuconfig BSP_USING_FLEXSPI
            bool "Enable FLEXSPI"
            default n
            if BSP_USING_FLEXSPI
                config BSP_USING_FLEXSPI1
                    bool "Enable FLEXSPI1"
                    default n
                config BSP_USING_FLEXSPI2
                    bool "Enable FLEXSPI2"
                    default n
            endif
endmenu

menu "Onboard Peripheral Drivers"

    config BSP_USING_SDRAM
        bool "Enable SDRAM"
        default n

    menuconfig BSP_USING_ETH
    bool "Enable Ethernet"
    select RT_USING_NETDEV
    select RT_USING_LWIP
    default n


    if BSP_USING_ETH
        config BSP_USING_PHY
            select RT_USING_PHY
            bool "Enable ethernet phy"
            default y

        if BSP_USING_PHY
            config PHY_USING_KSZ8081
                bool "i.MX RT1176EVK uses ksz8081 phy"
                default y

            if PHY_USING_KSZ8081
                config PHY_KSZ8081_ADDRESS
                int "Specify address of phy device"
                default 2

                config PHY_RESET_KSZ8081_PORT
                    int "indicate port of reset"
                    default 6

                config PHY_RESET_KSZ8081_PIN
                    int "indicate pin of reset"
                    default 12

                config FSL_FEATURE_PHYKSZ8081_USE_RMII50M_MODE
                    bool "Enable the PHY ksz8081 RMII50M mode"
                    depends on PHY_USING_KSZ8081
                    default y
            endif
        endif

        if BSP_USING_PHY
                config PHY_USING_RTL8211F
                    bool "i.MX RT1176EVK uses rtl8211f phy"
                    default y

                if PHY_USING_RTL8211F
                    config PHY_RTL8211F_ADDRESS
                    int "Specify address of phy device"
                    default 1

                    config PHY_RESET_RTL8211F_PORT
                        int "indicate port of reset"
                        default 5

                    config PHY_RESET_RTL8211F_PIN
                        int "indicate pin of reset"
                        default 14

                endif
        endif
    endif

    menuconfig BSP_USING_FS
        bool "Enable File System"
        select RT_USING_DFS_DEVFS
        select RT_USING_DFS
        default n

        if BSP_USING_FS
            config BSP_USING_SDCARD_FATFS
                bool "Enable SDCARD (FATFS)"
                select BSP_USING_SDIO
                select RT_USING_DFS_ELMFAT
                default n
        endif

endmenu

menu "Board extended module Drivers"

endmenu

endmenu