rt-thread-official/bsp/gd32e230k-start/Libraries/GD32E230_standard_peripheral/Source/gd32e230_misc.c

/*!
    \file    gd32e230_misc.c
    \brief   MISC driver
    
    \version 2018-06-19, V1.0.0, firmware for GD32E230
*/

/*
    Copyright (c) 2018, GigaDevice Semiconductor Inc.

    All rights reserved.

    Redistribution and use in source and binary forms, with or without modification, 
are permitted provided that the following conditions are met:

    1. Redistributions of source code must retain the above copyright notice, this 
       list of conditions and the following disclaimer.
    2. Redistributions in binary form must reproduce the above copyright notice, 
       this list of conditions and the following disclaimer in the documentation 
       and/or other materials provided with the distribution.
    3. Neither the name of the copyright holder nor the names of its contributors 
       may be used to endorse or promote products derived from this software without 
       specific prior written permission.

    THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS "AS IS" 
AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED 
WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE DISCLAIMED. 
IN NO EVENT SHALL THE COPYRIGHT HOLDER OR CONTRIBUTORS BE LIABLE FOR ANY DIRECT, 
INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING, BUT 
NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS OF USE, DATA, OR 
PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY, 
WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) 
ARISING IN ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY 
OF SUCH DAMAGE.
*/

#include "gd32e230_misc.h"

/*!
    \brief      enable NVIC request
    \param[in]  nvic_irq: the NVIC interrupt request, detailed in IRQn_Type
    \param[in]  nvic_irq_priority: the priority needed to set (0-3)
    \param[out] none
    \retval     none
*/
void nvic_irq_enable(uint8_t nvic_irq, 
                     uint8_t nvic_irq_priority)
{
    /* set the priority and enable the selected IRQ */
    NVIC_SetPriority((IRQn_Type)nvic_irq, (uint32_t)nvic_irq_priority);
    NVIC_EnableIRQ((IRQn_Type)nvic_irq);
}

/*!
    \brief      disable NVIC request
    \param[in]  nvic_irq: the NVIC interrupt request, detailed in IRQn_Type
    \param[out] none
    \retval     none
*/
void nvic_irq_disable(uint8_t nvic_irq)
{
    /* disable the selected IRQ.*/
    NVIC_DisableIRQ((IRQn_Type)nvic_irq);
}

/*  */
/*!
    \brief      initiates a system reset request to reset the MCU
    \param[in]  none
    \param[out] none
    \retval     none
*/
void nvic_system_reset(void)
{
    NVIC_SystemReset();
}

/*!
    \brief      set the NVIC vector table base address
    \param[in]  nvic_vict_tab: the RAM or FLASH base address
      \arg        NVIC_VECTTAB_RAM: RAM base address
      \arg        NVIC_VECTTAB_FLASH: Flash base address
    \param[in]  offset: Vector Table offset
    \param[out] none
    \retval     none
*/
void nvic_vector_table_set(uint32_t nvic_vict_tab, uint32_t offset)
{
    SCB->VTOR = nvic_vict_tab | (offset & NVIC_VECTTAB_OFFSET_MASK);
}

/*!
    \brief      set the state of the low power mode
    \param[in]  lowpower_mode: the low power mode state
      \arg        SCB_LPM_SLEEP_EXIT_ISR: if chose this para, the system always enter low power 
                    mode by exiting from ISR
      \arg        SCB_LPM_DEEPSLEEP: if chose this para, the system will enter the DEEPSLEEP mode
      \arg        SCB_LPM_WAKE_BY_ALL_INT: if chose this para, the lowpower mode can be woke up 
                    by all the enable and disable interrupts
    \param[out] none
    \retval     none
*/
void system_lowpower_set(uint8_t lowpower_mode)
{
    SCB->SCR |= (uint32_t)lowpower_mode;
}

/*!
    \brief      reset the state of the low power mode
    \param[in]  lowpower_mode: the low power mode state
      \arg        SCB_LPM_SLEEP_EXIT_ISR: if chose this para, the system will exit low power 
                    mode by exiting from ISR
      \arg        SCB_LPM_DEEPSLEEP: if chose this para, the system will enter the SLEEP mode
      \arg        SCB_LPM_WAKE_BY_ALL_INT: if chose this para, the lowpower mode only can be 
                    woke up by the enable interrupts
    \param[out] none
    \retval     none
*/
void system_lowpower_reset(uint8_t lowpower_mode)
{
    SCB->SCR &= (~(uint32_t)lowpower_mode);
}

/*!
    \brief      set the systick clock source
    \param[in]  systick_clksource: the systick clock source needed to choose
      \arg        SYSTICK_CLKSOURCE_HCLK: systick clock source is from HCLK
      \arg        SYSTICK_CLKSOURCE_HCLK_DIV8: systick clock source is from HCLK/8
    \param[out] none
    \retval     none
*/

void systick_clksource_set(uint32_t systick_clksource)
{
    if(SYSTICK_CLKSOURCE_HCLK == systick_clksource ){
        /* set the systick clock source from HCLK */
        SysTick->CTRL |= SYSTICK_CLKSOURCE_HCLK;
    }else{
        /* set the systick clock source from HCLK/8 */
        SysTick->CTRL &= SYSTICK_CLKSOURCE_HCLK_DIV8;
    }
}