libs/rt-thread-official
libs
/
rt-thread-official
mirror of https://github.com/RT-Thread/rt-thread.git
4
0
Fork 0
Code Issues Releases Wiki Activity
rt-thread-official/bsp/tm4c129x/libraries/driverlib/sysctl.c

3700 lines
133 KiB
C
Raw Normal View History

[bsp] Add BSP for TM4C1294XL (TI Tiva C Series Connected LaunchPad)
2014-07-18 17:17:56 +08:00
//*****************************************************************************
//
// sysctl.c - Driver for the system controller.
//
// Copyright (c) 2005-2014 Texas Instruments Incorporated. All rights reserved.
// Software License Agreement
//
// Redistribution and use in source and binary forms, with or without
// modification, are permitted provided that the following conditions
// are met:
//
// Redistributions of source code must retain the above copyright
// notice, this list of conditions and the following disclaimer.
//
// Redistributions in binary form must reproduce the above copyright
// notice, this list of conditions and the following disclaimer in the
// documentation and/or other materials provided with the
// distribution.
//
// Neither the name of Texas Instruments Incorporated nor the names of
// its contributors may be used to endorse or promote products derived
// from this software without specific prior written permission.
//
// THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS
// "AS IS" AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT
// LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR
// A PARTICULAR PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL THE COPYRIGHT
// OWNER OR CONTRIBUTORS BE LIABLE FOR ANY DIRECT, INDIRECT, INCIDENTAL,
// SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING, BUT NOT
// LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS OF USE,
// DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND ON ANY
// THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT
// (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE
// OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.
//
// This is part of revision 2.1.0.12573 of the Tiva Peripheral Driver Library.
//
//*****************************************************************************
//*****************************************************************************
//
//! \addtogroup sysctl_api
//! @{
//
//*****************************************************************************
#include <stdbool.h>
#include <stdint.h>
#include "inc/hw_ints.h"
#include "inc/hw_nvic.h"
#include "inc/hw_sysctl.h"
#include "inc/hw_types.h"
#include "inc/hw_flash.h"
#include "driverlib/cpu.h"
#include "driverlib/debug.h"
#include "driverlib/interrupt.h"
#include "driverlib/sysctl.h"
//*****************************************************************************
//
// The flash shift used in the math to calculate the flash sector size.
//
//*****************************************************************************
#ifndef FLASH_PP_MAINSS_S
#define FLASH_PP_MAINSS_S 16
#endif
//*****************************************************************************
//
// This macro converts the XTAL value provided in the ui32Config parameter to
// an index to the g_pui32Xtals array.
//
//*****************************************************************************
#define SysCtlXtalCfgToIndex(a) ((a & 0x7c0) >> 6)
//*****************************************************************************
//
// An array that maps the crystal number in RCC to a frequency.
//
//*****************************************************************************
static const uint32_t g_pui32Xtals[] =
{
1000000,
1843200,
2000000,
2457600,
3579545,
3686400,
4000000,
4096000,
4915200,
5000000,
5120000,
6000000,
6144000,
7372800,
8000000,
8192000,
10000000,
12000000,
12288000,
13560000,
14318180,
16000000,
16384000,
18000000,
20000000,
24000000,
25000000
};
//*****************************************************************************
//
// Maximum number of VCO entries in the g_pui32XTALtoVCO and
// g_pui32VCOFrequencies structures for a device.
//
//*****************************************************************************
#define MAX_VCO_ENTRIES 2
#define MAX_XTAL_ENTRIES 18
//*****************************************************************************
//
// These macros are used in the g_pui32XTALtoVCO table to make it more
// readable.
//
//*****************************************************************************
#define PLL_M_TO_REG(mi, mf) \
((uint32_t)mi | (uint32_t)(mf << SYSCTL_PLLFREQ0_MFRAC_S))
#define PLL_N_TO_REG(n) \
((uint32_t)(n - 1) << SYSCTL_PLLFREQ1_N_S)
//*****************************************************************************
//
// Look up of the values that go into the PLLFREQ0 and PLLFREQ1 registers.
//
//*****************************************************************************
static const uint32_t g_pppui32XTALtoVCO[MAX_VCO_ENTRIES][MAX_XTAL_ENTRIES][2] =
{
{
//
// VCO 320 MHz
//
{ PLL_M_TO_REG(64, 0), PLL_N_TO_REG(1) }, // 5 MHz
{ PLL_M_TO_REG(62, 512), PLL_N_TO_REG(1) }, // 5.12 MHz
{ PLL_M_TO_REG(160, 0), PLL_N_TO_REG(3) }, // 6 MHz
{ PLL_M_TO_REG(52, 85), PLL_N_TO_REG(1) }, // 6.144 MHz
{ PLL_M_TO_REG(43, 412), PLL_N_TO_REG(1) }, // 7.3728 MHz
{ PLL_M_TO_REG(40, 0), PLL_N_TO_REG(1) }, // 8 MHz
{ PLL_M_TO_REG(39, 64), PLL_N_TO_REG(1) }, // 8.192 MHz
{ PLL_M_TO_REG(32, 0), PLL_N_TO_REG(1) }, // 10 MHz
{ PLL_M_TO_REG(80, 0), PLL_N_TO_REG(3) }, // 12 MHz
{ PLL_M_TO_REG(26, 43), PLL_N_TO_REG(1) }, // 12.288 MHz
{ PLL_M_TO_REG(23, 613), PLL_N_TO_REG(1) }, // 13.56 MHz
{ PLL_M_TO_REG(22, 358), PLL_N_TO_REG(1) }, // 14.318180 MHz
{ PLL_M_TO_REG(20, 0), PLL_N_TO_REG(1) }, // 16 MHz
{ PLL_M_TO_REG(19, 544), PLL_N_TO_REG(1) }, // 16.384 MHz
{ PLL_M_TO_REG(160, 0), PLL_N_TO_REG(9) }, // 18 MHz
{ PLL_M_TO_REG(16, 0), PLL_N_TO_REG(1) }, // 20 MHz
{ PLL_M_TO_REG(40, 0), PLL_N_TO_REG(3) }, // 24 MHz
{ PLL_M_TO_REG(64, 0), PLL_N_TO_REG(5) }, // 25 MHz
},
{
//
// VCO 480 MHz
//
{ PLL_M_TO_REG(96, 0), PLL_N_TO_REG(1) }, // 5 MHz
{ PLL_M_TO_REG(93, 768), PLL_N_TO_REG(1) }, // 5.12 MHz
{ PLL_M_TO_REG(80, 0), PLL_N_TO_REG(1) }, // 6 MHz
{ PLL_M_TO_REG(78, 128), PLL_N_TO_REG(1) }, // 6.144 MHz
{ PLL_M_TO_REG(65, 107), PLL_N_TO_REG(1) }, // 7.3728 MHz
{ PLL_M_TO_REG(60, 0), PLL_N_TO_REG(1) }, // 8 MHz
{ PLL_M_TO_REG(58, 608), PLL_N_TO_REG(1) }, // 8.192 MHz
{ PLL_M_TO_REG(48, 0), PLL_N_TO_REG(1) }, // 10 MHz
{ PLL_M_TO_REG(40, 0), PLL_N_TO_REG(1) }, // 12 MHz
{ PLL_M_TO_REG(39, 64), PLL_N_TO_REG(1) }, // 12.288 MHz
{ PLL_M_TO_REG(35, 408), PLL_N_TO_REG(1) }, // 13.56 MHz
{ PLL_M_TO_REG(33, 536), PLL_N_TO_REG(1) }, // 14.318180 MHz
{ PLL_M_TO_REG(30, 0), PLL_N_TO_REG(1) }, // 16 MHz
{ PLL_M_TO_REG(29, 304), PLL_N_TO_REG(1) }, // 16.384 MHz
{ PLL_M_TO_REG(80, 0), PLL_N_TO_REG(3) }, // 18 MHz
{ PLL_M_TO_REG(24, 0), PLL_N_TO_REG(1) }, // 20 MHz
{ PLL_M_TO_REG(20, 0), PLL_N_TO_REG(1) }, // 24 MHz
{ PLL_M_TO_REG(96, 0), PLL_N_TO_REG(5) }, // 25 MHz
},
};
//*****************************************************************************
//
// The mapping of system clock frequency to flash memory timing parameters.
//
//*****************************************************************************
static const struct
{
uint32_t ui32Frequency;
uint32_t ui32MemTiming;
}
g_sXTALtoMEMTIM[] =
{
{ 16000000, (SYSCTL_MEMTIM0_FBCHT_0_5 | SYSCTL_MEMTIM0_FBCE |
(0 << SYSCTL_MEMTIM0_FWS_S) |
SYSCTL_MEMTIM0_EBCHT_0_5 | SYSCTL_MEMTIM0_EBCE |
(0 << SYSCTL_MEMTIM0_EWS_S) |
SYSCTL_MEMTIM0_MB1) },
{ 40000000, (SYSCTL_MEMTIM0_FBCHT_1_5 | (1 << SYSCTL_MEMTIM0_FWS_S) |
SYSCTL_MEMTIM0_FBCHT_1_5 | (1 << SYSCTL_MEMTIM0_EWS_S) |
SYSCTL_MEMTIM0_MB1) },
{ 60000000, (SYSCTL_MEMTIM0_FBCHT_2 | (2 << SYSCTL_MEMTIM0_FWS_S) |
SYSCTL_MEMTIM0_EBCHT_2 | (2 << SYSCTL_MEMTIM0_EWS_S) |
SYSCTL_MEMTIM0_MB1) },
{ 80000000, (SYSCTL_MEMTIM0_FBCHT_2_5 | (3 << SYSCTL_MEMTIM0_FWS_S) |
SYSCTL_MEMTIM0_EBCHT_2_5 | (3 << SYSCTL_MEMTIM0_EWS_S) |
SYSCTL_MEMTIM0_MB1) },
{ 100000000, (SYSCTL_MEMTIM0_FBCHT_3 | (4 << SYSCTL_MEMTIM0_FWS_S) |
SYSCTL_MEMTIM0_EBCHT_3 | (4 << SYSCTL_MEMTIM0_EWS_S) |
SYSCTL_MEMTIM0_MB1) },
{ 120000000, (SYSCTL_MEMTIM0_FBCHT_3_5 | (5 << SYSCTL_MEMTIM0_FWS_S) |
SYSCTL_MEMTIM0_EBCHT_3_5 | (5 << SYSCTL_MEMTIM0_EWS_S) |
SYSCTL_MEMTIM0_MB1) },
};
//*****************************************************************************
//
// Get the correct memory timings for a given system clock value.
//
//*****************************************************************************
static uint32_t
_SysCtlMemTimingGet(uint32_t ui32SysClock)
{
uint_fast8_t ui8Idx;
//
// Loop through the flash memory timings.
//
for(ui8Idx = 0;
ui8Idx < (sizeof(g_sXTALtoMEMTIM) / sizeof(g_sXTALtoMEMTIM[0]));
ui8Idx++)
{
//
// See if the system clock frequency is less than the maximum frequency
// for this flash memory timing.
//
if(ui32SysClock <= g_sXTALtoMEMTIM[ui8Idx].ui32Frequency)
{
//
// This flash memory timing is the best choice for the system clock
// frequency, so return it now.
//
return(g_sXTALtoMEMTIM[ui8Idx].ui32MemTiming);
}
}
//
// An appropriate flash memory timing could not be found, so the device is
// being clocked too fast. Return the default flash memory timing.
//
return(0);
}
//*****************************************************************************
//
// Calculate the system frequency from the register settings base on the
// oscillator input.
//
//*****************************************************************************
static uint32_t
_SysCtlFrequencyGet(uint32_t ui32Xtal)
{
uint32_t ui32Result;
uint_fast16_t ui16F1, ui16F2;
uint_fast16_t ui16PInt, ui16PFract;
uint_fast8_t ui8Q, ui8N;
//
// Extract all of the values from the hardware registers.
//
ui16PFract = ((HWREG(SYSCTL_PLLFREQ0) & SYSCTL_PLLFREQ0_MFRAC_M) >>
SYSCTL_PLLFREQ0_MFRAC_S);
ui16PInt = HWREG(SYSCTL_PLLFREQ0) & SYSCTL_PLLFREQ0_MINT_M;
ui8Q = (((HWREG(SYSCTL_PLLFREQ1) & SYSCTL_PLLFREQ1_Q_M) >>
SYSCTL_PLLFREQ1_Q_S) + 1);
ui8N = (((HWREG(SYSCTL_PLLFREQ1) & SYSCTL_PLLFREQ1_N_M) >>
SYSCTL_PLLFREQ1_N_S) + 1);
//
// Divide the crystal value by N.
//
ui32Xtal /= (uint32_t)ui8N;
//
// Calculate the multiplier for bits 9:5.
//
ui16F1 = ui16PFract / 32;
//
// Calculate the multiplier for bits 4:0.
//
ui16F2 = ui16PFract - (ui16F1 * 32);
//
// Get the integer portion.
//
ui32Result = ui32Xtal * (uint32_t)ui16PInt;
//
// Add first fractional bits portion(9:0).
//
ui32Result += (ui32Xtal * (uint32_t)ui16F1) / 32;
//
// Add the second fractional bits portion(4:0).
//
ui32Result += (ui32Xtal * (uint32_t)ui16F2) / 1024;
//
// Divide the result by Q.
//
ui32Result = ui32Result / (uint32_t)ui8Q;
//
// Return the resulting PLL frequency.
//
return(ui32Result);
}
//*****************************************************************************
//
// Look up of the possible VCO frequencies.
//
//*****************************************************************************
static const uint32_t g_pui32VCOFrequencies[MAX_VCO_ENTRIES] =
{
320000000, // VCO 320
480000000, // VCO 480
};
//*****************************************************************************
//
// The base addresses of the various peripheral control registers.
//
//*****************************************************************************
#define SYSCTL_PPBASE 0x400fe300
#define SYSCTL_SRBASE 0x400fe500
#define SYSCTL_RCGCBASE 0x400fe600
#define SYSCTL_SCGCBASE 0x400fe700
#define SYSCTL_DCGCBASE 0x400fe800
#define SYSCTL_PCBASE 0x400fe900
#define SYSCTL_PRBASE 0x400fea00
//*****************************************************************************
//
//! \internal
//! Checks a peripheral identifier.
//!
//! \param ui32Peripheral is the peripheral identifier.
//!
//! This function determines if a peripheral identifier is valid.
//!
//! \return Returns \b true if the peripheral identifier is valid and \b false
//! otherwise.
//
//*****************************************************************************
#ifdef DEBUG
static bool
_SysCtlPeripheralValid(uint32_t ui32Peripheral)
{
return((ui32Peripheral == SYSCTL_PERIPH_ADC0) ||
(ui32Peripheral == SYSCTL_PERIPH_ADC1) ||
(ui32Peripheral == SYSCTL_PERIPH_CAN0) ||
(ui32Peripheral == SYSCTL_PERIPH_CAN1) ||
(ui32Peripheral == SYSCTL_PERIPH_COMP0) ||
(ui32Peripheral == SYSCTL_PERIPH_CCM0) ||
(ui32Peripheral == SYSCTL_PERIPH_EEPROM0) ||
(ui32Peripheral == SYSCTL_PERIPH_EPHY0) ||
(ui32Peripheral == SYSCTL_PERIPH_EMAC0) ||
(ui32Peripheral == SYSCTL_PERIPH_EPI0) ||
(ui32Peripheral == SYSCTL_PERIPH_FAN0) ||
(ui32Peripheral == SYSCTL_PERIPH_GPIOA) ||
(ui32Peripheral == SYSCTL_PERIPH_GPIOB) ||
(ui32Peripheral == SYSCTL_PERIPH_GPIOC) ||
(ui32Peripheral == SYSCTL_PERIPH_GPIOD) ||
(ui32Peripheral == SYSCTL_PERIPH_GPIOE) ||
(ui32Peripheral == SYSCTL_PERIPH_GPIOF) ||
(ui32Peripheral == SYSCTL_PERIPH_GPIOG) ||
(ui32Peripheral == SYSCTL_PERIPH_GPIOH) ||
(ui32Peripheral == SYSCTL_PERIPH_GPIOJ) ||
(ui32Peripheral == SYSCTL_PERIPH_GPIOK) ||
(ui32Peripheral == SYSCTL_PERIPH_GPIOL) ||
(ui32Peripheral == SYSCTL_PERIPH_GPIOM) ||
(ui32Peripheral == SYSCTL_PERIPH_GPION) ||
(ui32Peripheral == SYSCTL_PERIPH_GPIOP) ||
(ui32Peripheral == SYSCTL_PERIPH_GPIOQ) ||
(ui32Peripheral == SYSCTL_PERIPH_GPIOR) ||
(ui32Peripheral == SYSCTL_PERIPH_GPIOS) ||
(ui32Peripheral == SYSCTL_PERIPH_GPIOT) ||
(ui32Peripheral == SYSCTL_PERIPH_HIBERNATE) ||
(ui32Peripheral == SYSCTL_PERIPH_I2C0) ||
(ui32Peripheral == SYSCTL_PERIPH_I2C1) ||
(ui32Peripheral == SYSCTL_PERIPH_I2C2) ||
(ui32Peripheral == SYSCTL_PERIPH_I2C3) ||
(ui32Peripheral == SYSCTL_PERIPH_I2C4) ||
(ui32Peripheral == SYSCTL_PERIPH_I2C5) ||
(ui32Peripheral == SYSCTL_PERIPH_I2C6) ||
(ui32Peripheral == SYSCTL_PERIPH_I2C7) ||
(ui32Peripheral == SYSCTL_PERIPH_I2C8) ||
(ui32Peripheral == SYSCTL_PERIPH_I2C9) ||
(ui32Peripheral == SYSCTL_PERIPH_LCD0) ||
(ui32Peripheral == SYSCTL_PERIPH_PWM0) ||
(ui32Peripheral == SYSCTL_PERIPH_PWM1) ||
(ui32Peripheral == SYSCTL_PERIPH_QEI0) ||
(ui32Peripheral == SYSCTL_PERIPH_QEI1) ||
(ui32Peripheral == SYSCTL_PERIPH_SSI0) ||
(ui32Peripheral == SYSCTL_PERIPH_SSI1) ||
(ui32Peripheral == SYSCTL_PERIPH_SSI2) ||
(ui32Peripheral == SYSCTL_PERIPH_SSI3) ||
(ui32Peripheral == SYSCTL_PERIPH_TIMER0) ||
(ui32Peripheral == SYSCTL_PERIPH_TIMER1) ||
(ui32Peripheral == SYSCTL_PERIPH_TIMER2) ||
(ui32Peripheral == SYSCTL_PERIPH_TIMER3) ||
(ui32Peripheral == SYSCTL_PERIPH_TIMER4) ||
(ui32Peripheral == SYSCTL_PERIPH_TIMER5) ||
(ui32Peripheral == SYSCTL_PERIPH_UART0) ||
(ui32Peripheral == SYSCTL_PERIPH_UART1) ||
(ui32Peripheral == SYSCTL_PERIPH_UART2) ||
(ui32Peripheral == SYSCTL_PERIPH_UART3) ||
(ui32Peripheral == SYSCTL_PERIPH_UART4) ||
(ui32Peripheral == SYSCTL_PERIPH_UART5) ||
(ui32Peripheral == SYSCTL_PERIPH_UART6) ||
(ui32Peripheral == SYSCTL_PERIPH_UART7) ||
(ui32Peripheral == SYSCTL_PERIPH_UDMA) ||
(ui32Peripheral == SYSCTL_PERIPH_USB0) ||
(ui32Peripheral == SYSCTL_PERIPH_WDOG0) ||
(ui32Peripheral == SYSCTL_PERIPH_WDOG1) ||
(ui32Peripheral == SYSCTL_PERIPH_WTIMER0) ||
(ui32Peripheral == SYSCTL_PERIPH_WTIMER1) ||
(ui32Peripheral == SYSCTL_PERIPH_WTIMER2) ||
(ui32Peripheral == SYSCTL_PERIPH_WTIMER3) ||
(ui32Peripheral == SYSCTL_PERIPH_WTIMER4) ||
(ui32Peripheral == SYSCTL_PERIPH_WTIMER5));
}
#endif
//*****************************************************************************
//
//! Gets the size of the SRAM.
//!
//! This function determines the size of the SRAM on the Tiva device.
//!
//! \return The total number of bytes of SRAM.
//
//*****************************************************************************
uint32_t
SysCtlSRAMSizeGet(void)
{
return((HWREG(FLASH_SSIZE) + 1) * 256);
}
//*****************************************************************************
//
//! Gets the size of the flash.
//!
//! This function determines the size of the flash on the Tiva device.
//!
//! \return The total number of bytes of flash.
//
//*****************************************************************************
uint32_t
SysCtlFlashSizeGet(void)
{
//
// TM4C123 devices report the flash size in DC0.
//
if(CLASS_IS_TM4C123)
{
//
// Compute the size of the flash.
//
return(((HWREG(SYSCTL_DC0) & SYSCTL_DC0_FLASHSZ_M) << 11) + 0x800);
}
else
{
//
// Get the flash size from the FLASH_PP register.
//
return(2048 * ((HWREG(FLASH_PP) & FLASH_PP_SIZE_M) + 1));
}
}
//*****************************************************************************
//
//! Gets the size of a single eraseable sector of flash.
//!
//! This function determines the flash sector size on the Tiva device.
//! This size determines the erase granularity of the device flash.
//!
//! \return The number of bytes in a single flash sector.
//
//*****************************************************************************
uint32_t
SysCtlFlashSectorSizeGet(void)
{
//
// TM4C129 devices store the value in a different register.
//
if(CLASS_IS_TM4C129)
{
//
// Get the flash sector size from the FLASH_PP register.
//
return(1 << (10 +
((HWREG(FLASH_PP) &
FLASH_PP_MAINSS_M) >> FLASH_PP_MAINSS_S)));
}
else
{
//
// The sector size is fixed at 1KB.
//
return(1024);
}
}
//*****************************************************************************
//
//! Determines if a peripheral is present.
//!
//! \param ui32Peripheral is the peripheral in question.
//!
//! This function determines if a particular peripheral is present in the
//! device. Each member of the Tiva family has a different peripheral
//! set; this function determines which peripherals are present on this device.
//!
//! The \e ui32Peripheral parameter must be only one of the following values:
//! \b SYSCTL_PERIPH_ADC0, \b SYSCTL_PERIPH_ADC1, \b SYSCTL_PERIPH_CAN0,
//! \b SYSCTL_PERIPH_CAN1, \b SYSCTL_PERIPH_CCM0,\b SYSCTL_PERIPH_COMP0,
//! \b SYSCTL_PERIPH_EEPROM0, \b SYSCTL_PERIPH_EMAC, \b SYSCTL_PERIPH_EPHY,
//! \b SYSCTL_PERIPH_EPI0,
//! \b SYSCTL_PERIPH_GPIOA, \b SYSCTL_PERIPH_GPIOB, \b SYSCTL_PERIPH_GPIOC,
//! \b SYSCTL_PERIPH_GPIOD, \b SYSCTL_PERIPH_GPIOE, \b SYSCTL_PERIPH_GPIOF,
//! \b SYSCTL_PERIPH_GPIOG, \b SYSCTL_PERIPH_GPIOH, \b SYSCTL_PERIPH_GPIOJ,
//! \b SYSCTL_PERIPH_GPIOK, \b SYSCTL_PERIPH_GPIOL, \b SYSCTL_PERIPH_GPIOM,
//! \b SYSCTL_PERIPH_GPION, \b SYSCTL_PERIPH_GPIOP, \b SYSCTL_PERIPH_GPIOQ,
//! \b SYSCTL_PERIPH_GPIOR, \b SYSCTL_PERIPH_GPIOS, \b SYSCTL_PERIPH_GPIOT,
//! \b SYSCTL_PERIPH_HIBERNATE,
//! \b SYSCTL_PERIPH_I2C0, \b SYSCTL_PERIPH_I2C1, \b SYSCTL_PERIPH_I2C2,
//! \b SYSCTL_PERIPH_I2C3, \b SYSCTL_PERIPH_I2C4, \b SYSCTL_PERIPH_I2C5,
//! \b SYSCTL_PERIPH_I2C6, \b SYSCTL_PERIPH_I2C7, \b SYSCTL_PERIPH_I2C8,
//! \b SYSCTL_PERIPH_I2C9, \b SYSCTL_PERIPH_LCD0,
//! \b SYSCTL_PERIPH_ONEWIRE0,
//! \b SYSCTL_PERIPH_PWM0, \b SYSCTL_PERIPH_PWM1, \b SYSCTL_PERIPH_QEI0,
//! \b SYSCTL_PERIPH_QEI1, \b SYSCTL_PERIPH_SSI0, \b SYSCTL_PERIPH_SSI1,
//! \b SYSCTL_PERIPH_SSI2, \b SYSCTL_PERIPH_SSI3, \b SYSCTL_PERIPH_TIMER0,
//! \b SYSCTL_PERIPH_TIMER1, \b SYSCTL_PERIPH_TIMER2, \b SYSCTL_PERIPH_TIMER3,
//! \b SYSCTL_PERIPH_TIMER4, \b SYSCTL_PERIPH_TIMER5, \b SYSCTL_PERIPH_TIMER6,
//! \b SYSCTL_PERIPH_TIMER7, \b SYSCTL_PERIPH_UART0, \b SYSCTL_PERIPH_UART1,
//! \b SYSCTL_PERIPH_UART2, \b SYSCTL_PERIPH_UART3, \b SYSCTL_PERIPH_UART4,
//! \b SYSCTL_PERIPH_UART5, \b SYSCTL_PERIPH_UART6, \b SYSCTL_PERIPH_UART7,
//! \b SYSCTL_PERIPH_UDMA, \b SYSCTL_PERIPH_USB0, \b SYSCTL_PERIPH_WDOG0,
//! \b SYSCTL_PERIPH_WDOG1, \b SYSCTL_PERIPH_WTIMER0, \b SYSCTL_PERIPH_WTIMER1,
//! \b SYSCTL_PERIPH_WTIMER2, \b SYSCTL_PERIPH_WTIMER3,
//! \b SYSCTL_PERIPH_WTIMER4, or \b SYSCTL_PERIPH_WTIMER5
//!
//! \return Returns \b true if the specified peripheral is present and \b false
//! if it is not.
//
//*****************************************************************************
bool
SysCtlPeripheralPresent(uint32_t ui32Peripheral)
{
//
// Check the arguments.
//
ASSERT(_SysCtlPeripheralValid(ui32Peripheral));
//
// See if this peripheral is present.
//
return(HWREGBITW(SYSCTL_PPBASE + ((ui32Peripheral & 0xff00) >> 8),
ui32Peripheral & 0xff));
}
//*****************************************************************************
//
//! Determines if a peripheral is ready.
//!
//! \param ui32Peripheral is the peripheral in question.
//!
//! This function determines if a particular peripheral is ready to be
//! accessed. The peripheral may be in a non-ready state if it is not enabled,
//! is being held in reset, or is in the process of becoming ready after being
//! enabled or taken out of reset.
//!
//! The \e ui32Peripheral parameter must be only one of the following values:
//! \b SYSCTL_PERIPH_ADC0, \b SYSCTL_PERIPH_ADC1, \b SYSCTL_PERIPH_CAN0,
//! \b SYSCTL_PERIPH_CAN1, \b SYSCTL_PERIPH_CCM0,\b SYSCTL_PERIPH_COMP0,
//! \b SYSCTL_PERIPH_EEPROM0, \b SYSCTL_PERIPH_EMAC, \b SYSCTL_PERIPH_EPHY,
//! \b SYSCTL_PERIPH_EPI0,
//! \b SYSCTL_PERIPH_GPIOA, \b SYSCTL_PERIPH_GPIOB, \b SYSCTL_PERIPH_GPIOC,
//! \b SYSCTL_PERIPH_GPIOD, \b SYSCTL_PERIPH_GPIOE, \b SYSCTL_PERIPH_GPIOF,
//! \b SYSCTL_PERIPH_GPIOG, \b SYSCTL_PERIPH_GPIOH, \b SYSCTL_PERIPH_GPIOJ,
//! \b SYSCTL_PERIPH_GPIOK, \b SYSCTL_PERIPH_GPIOL, \b SYSCTL_PERIPH_GPIOM,
//! \b SYSCTL_PERIPH_GPION, \b SYSCTL_PERIPH_GPIOP, \b SYSCTL_PERIPH_GPIOQ,
//! \b SYSCTL_PERIPH_GPIOR, \b SYSCTL_PERIPH_GPIOS, \b SYSCTL_PERIPH_GPIOT,
//! \b SYSCTL_PERIPH_HIBERNATE,
//! \b SYSCTL_PERIPH_I2C0, \b SYSCTL_PERIPH_I2C1, \b SYSCTL_PERIPH_I2C2,
//! \b SYSCTL_PERIPH_I2C3, \b SYSCTL_PERIPH_I2C4, \b SYSCTL_PERIPH_I2C5,
//! \b SYSCTL_PERIPH_I2C6, \b SYSCTL_PERIPH_I2C7, \b SYSCTL_PERIPH_I2C8,
//! \b SYSCTL_PERIPH_I2C9, \b SYSCTL_PERIPH_LCD0,
//! \b SYSCTL_PERIPH_ONEWIRE0,
//! \b SYSCTL_PERIPH_PWM0, \b SYSCTL_PERIPH_PWM1, \b SYSCTL_PERIPH_QEI0,
//! \b SYSCTL_PERIPH_QEI1, \b SYSCTL_PERIPH_SSI0, \b SYSCTL_PERIPH_SSI1,
//! \b SYSCTL_PERIPH_SSI2, \b SYSCTL_PERIPH_SSI3, \b SYSCTL_PERIPH_TIMER0,
//! \b SYSCTL_PERIPH_TIMER1, \b SYSCTL_PERIPH_TIMER2, \b SYSCTL_PERIPH_TIMER3,
//! \b SYSCTL_PERIPH_TIMER4, \b SYSCTL_PERIPH_TIMER5, \b SYSCTL_PERIPH_TIMER6,
//! \b SYSCTL_PERIPH_TIMER7, \b SYSCTL_PERIPH_UART0, \b SYSCTL_PERIPH_UART1,
//! \b SYSCTL_PERIPH_UART2, \b SYSCTL_PERIPH_UART3, \b SYSCTL_PERIPH_UART4,
//! \b SYSCTL_PERIPH_UART5, \b SYSCTL_PERIPH_UART6, \b SYSCTL_PERIPH_UART7,
//! \b SYSCTL_PERIPH_UDMA, \b SYSCTL_PERIPH_USB0, \b SYSCTL_PERIPH_WDOG0,
//! \b SYSCTL_PERIPH_WDOG1, \b SYSCTL_PERIPH_WTIMER0, \b SYSCTL_PERIPH_WTIMER1,
//! \b SYSCTL_PERIPH_WTIMER2, \b SYSCTL_PERIPH_WTIMER3,
//! \b SYSCTL_PERIPH_WTIMER4, or \b SYSCTL_PERIPH_WTIMER5
//!
//! \note The ability to check for a peripheral being ready varies based on the
//! Tiva part in use. Please consult the data sheet for the part you are
//! using to determine if this feature is available.
//!
//! \return Returns \b true if the specified peripheral is ready and \b false
//! if it is not.
//
//*****************************************************************************
bool
SysCtlPeripheralReady(uint32_t ui32Peripheral)
{
//
// Check the arguments.
//
ASSERT(_SysCtlPeripheralValid(ui32Peripheral));
//
// See if this peripheral is ready.
//
return(HWREGBITW(SYSCTL_PRBASE + ((ui32Peripheral & 0xff00) >> 8),
ui32Peripheral & 0xff));
}
//*****************************************************************************
//
//! Powers on a peripheral.
//!
//! \param ui32Peripheral is the peripheral to be powered on.
//!
//! This function turns on the power to a peripheral. The peripheral continues
//! to receive power even when its clock is not enabled.
//!
//! The \e ui32Peripheral parameter must be only one of the following values:
//! \b SYSCTL_PERIPH_CAN0,\b SYSCTL_PERIPH_CAN1, \b SYSCTL_PERIPH_EMAC,
//! \b SYSCTL_PERIPH_EPHY, \b SYSCTL_PERIPH_LCD0, \b SYSCTL_PERIPH_USB0
//!
//! \note The ability to power off a peripheral varies based on the Tiva
//! part in use. Please consult the data sheet for the part you are using to
//! determine if this feature is available.
//!
//! \return None.
//
//*****************************************************************************
void
SysCtlPeripheralPowerOn(uint32_t ui32Peripheral)
{
//
// Check the arguments.
//
ASSERT(_SysCtlPeripheralValid(ui32Peripheral));
//
// Power on this peripheral.
//
HWREGBITW(SYSCTL_PCBASE + ((ui32Peripheral & 0xff00) >> 8),
ui32Peripheral & 0xff) = 1;
}
//*****************************************************************************
//
//! Powers off a peripheral.
//!
//! \param ui32Peripheral is the peripheral to be powered off.
//!
//! This function allows the power to a peripheral to be turned off. The
//! peripheral continues to receive power when its clock is enabled, but
//! the power is removed when its clock is disabled.
//!
//! The \e ui32Peripheral parameter must be only one of the following values:
//! \b SYSCTL_PERIPH_CAN0,\b SYSCTL_PERIPH_CAN1, \b SYSCTL_PERIPH_EMAC,
//! \b SYSCTL_PERIPH_EPHY, \b SYSCTL_PERIPH_LCD0, \b SYSCTL_PERIPH_USB0
//!
//! \note The ability to power off a peripheral varies based on the Tiva
//! part in use. Please consult the data sheet for the part you are using to
//! determine if this feature is available.
//!
//! \return None.
//
//*****************************************************************************
void
SysCtlPeripheralPowerOff(uint32_t ui32Peripheral)
{
//
// Check the arguments.
//
ASSERT(_SysCtlPeripheralValid(ui32Peripheral));
//
// Power off this peripheral.
//
HWREGBITW(SYSCTL_PCBASE + ((ui32Peripheral & 0xff00) >> 8),
ui32Peripheral & 0xff) = 0;
}
//*****************************************************************************
//
//! Performs a software reset of a peripheral.
//!
//! \param ui32Peripheral is the peripheral to reset.
//!
//! This function performs a software reset of the specified peripheral. An
//! individual peripheral reset signal is asserted for a brief period and then
//! de-asserted, returning the internal state of the peripheral to its reset
//! condition.
//!
//! The \e ui32Peripheral parameter must be only one of the following values:
//! \b SYSCTL_PERIPH_ADC0, \b SYSCTL_PERIPH_ADC1, \b SYSCTL_PERIPH_CAN0,
//! \b SYSCTL_PERIPH_CAN1, \b SYSCTL_PERIPH_CCM0,\b SYSCTL_PERIPH_COMP0,
//! \b SYSCTL_PERIPH_EEPROM0, \b SYSCTL_PERIPH_EMAC, \b SYSCTL_PERIPH_EPHY,
//! \b SYSCTL_PERIPH_EPI0,
//! \b SYSCTL_PERIPH_GPIOA, \b SYSCTL_PERIPH_GPIOB, \b SYSCTL_PERIPH_GPIOC,
//! \b SYSCTL_PERIPH_GPIOD, \b SYSCTL_PERIPH_GPIOE, \b SYSCTL_PERIPH_GPIOF,
//! \b SYSCTL_PERIPH_GPIOG, \b SYSCTL_PERIPH_GPIOH, \b SYSCTL_PERIPH_GPIOJ,
//! \b SYSCTL_PERIPH_GPIOK, \b SYSCTL_PERIPH_GPIOL, \b SYSCTL_PERIPH_GPIOM,
//! \b SYSCTL_PERIPH_GPION, \b SYSCTL_PERIPH_GPIOP, \b SYSCTL_PERIPH_GPIOQ,
//! \b SYSCTL_PERIPH_GPIOR, \b SYSCTL_PERIPH_GPIOS, \b SYSCTL_PERIPH_GPIOT,
//! \b SYSCTL_PERIPH_HIBERNATE,
//! \b SYSCTL_PERIPH_I2C0, \b SYSCTL_PERIPH_I2C1, \b SYSCTL_PERIPH_I2C2,
//! \b SYSCTL_PERIPH_I2C3, \b SYSCTL_PERIPH_I2C4, \b SYSCTL_PERIPH_I2C5,
//! \b SYSCTL_PERIPH_I2C6, \b SYSCTL_PERIPH_I2C7, \b SYSCTL_PERIPH_I2C8,
//! \b SYSCTL_PERIPH_I2C9, \b SYSCTL_PERIPH_LCD0,
//! \b SYSCTL_PERIPH_ONEWIRE0,
//! \b SYSCTL_PERIPH_PWM0, \b SYSCTL_PERIPH_PWM1, \b SYSCTL_PERIPH_QEI0,
//! \b SYSCTL_PERIPH_QEI1, \b SYSCTL_PERIPH_SSI0, \b SYSCTL_PERIPH_SSI1,
//! \b SYSCTL_PERIPH_SSI2, \b SYSCTL_PERIPH_SSI3, \b SYSCTL_PERIPH_TIMER0,
//! \b SYSCTL_PERIPH_TIMER1, \b SYSCTL_PERIPH_TIMER2, \b SYSCTL_PERIPH_TIMER3,
//! \b SYSCTL_PERIPH_TIMER4, \b SYSCTL_PERIPH_TIMER5, \b SYSCTL_PERIPH_TIMER6,
//! \b SYSCTL_PERIPH_TIMER7, \b SYSCTL_PERIPH_UART0, \b SYSCTL_PERIPH_UART1,
//! \b SYSCTL_PERIPH_UART2, \b SYSCTL_PERIPH_UART3, \b SYSCTL_PERIPH_UART4,
//! \b SYSCTL_PERIPH_UART5, \b SYSCTL_PERIPH_UART6, \b SYSCTL_PERIPH_UART7,
//! \b SYSCTL_PERIPH_UDMA, \b SYSCTL_PERIPH_USB0, \b SYSCTL_PERIPH_WDOG0,
//! \b SYSCTL_PERIPH_WDOG1, \b SYSCTL_PERIPH_WTIMER0, \b SYSCTL_PERIPH_WTIMER1,
//! \b SYSCTL_PERIPH_WTIMER2, \b SYSCTL_PERIPH_WTIMER3,
//! \b SYSCTL_PERIPH_WTIMER4, or \b SYSCTL_PERIPH_WTIMER5
//!
//! \return None.
//
//*****************************************************************************
void
SysCtlPeripheralReset(uint32_t ui32Peripheral)
{
volatile uint_fast8_t ui8Delay;
//
// Check the arguments.
//
ASSERT(_SysCtlPeripheralValid(ui32Peripheral));
//
// Put the peripheral into the reset state.
//
HWREGBITW(SYSCTL_SRBASE + ((ui32Peripheral & 0xff00) >> 8),
ui32Peripheral & 0xff) = 1;
//
// Delay for a little bit.
//
for(ui8Delay = 0; ui8Delay < 16; ui8Delay++)
{
}
//
// Take the peripheral out of the reset state.
//
HWREGBITW(SYSCTL_SRBASE + ((ui32Peripheral & 0xff00) >> 8),
ui32Peripheral & 0xff) = 0;
}
//*****************************************************************************
//
//! Enables a peripheral.
//!
//! \param ui32Peripheral is the peripheral to enable.
//!
//! This function enables a peripheral. At power-up, all peripherals are
//! disabled; they must be enabled in order to operate or respond to register
//! reads/writes.
//!
//! The \e ui32Peripheral parameter must be only one of the following values:
//! \b SYSCTL_PERIPH_ADC0, \b SYSCTL_PERIPH_ADC1, \b SYSCTL_PERIPH_CAN0,
//! \b SYSCTL_PERIPH_CAN1, \b SYSCTL_PERIPH_CCM0,\b SYSCTL_PERIPH_COMP0,
//! \b SYSCTL_PERIPH_EEPROM0, \b SYSCTL_PERIPH_EMAC, \b SYSCTL_PERIPH_EPHY,
//! \b SYSCTL_PERIPH_EPI0,
//! \b SYSCTL_PERIPH_GPIOA, \b SYSCTL_PERIPH_GPIOB, \b SYSCTL_PERIPH_GPIOC,
//! \b SYSCTL_PERIPH_GPIOD, \b SYSCTL_PERIPH_GPIOE, \b SYSCTL_PERIPH_GPIOF,
//! \b SYSCTL_PERIPH_GPIOG, \b SYSCTL_PERIPH_GPIOH, \b SYSCTL_PERIPH_GPIOJ,
//! \b SYSCTL_PERIPH_GPIOK, \b SYSCTL_PERIPH_GPIOL, \b SYSCTL_PERIPH_GPIOM,
//! \b SYSCTL_PERIPH_GPION, \b SYSCTL_PERIPH_GPIOP, \b SYSCTL_PERIPH_GPIOQ,
//! \b SYSCTL_PERIPH_GPIOR, \b SYSCTL_PERIPH_GPIOS, \b SYSCTL_PERIPH_GPIOT,
//! \b SYSCTL_PERIPH_HIBERNATE,
//! \b SYSCTL_PERIPH_I2C0, \b SYSCTL_PERIPH_I2C1, \b SYSCTL_PERIPH_I2C2,
//! \b SYSCTL_PERIPH_I2C3, \b SYSCTL_PERIPH_I2C4, \b SYSCTL_PERIPH_I2C5,
//! \b SYSCTL_PERIPH_I2C6, \b SYSCTL_PERIPH_I2C7, \b SYSCTL_PERIPH_I2C8,
//! \b SYSCTL_PERIPH_I2C9, \b SYSCTL_PERIPH_LCD0,
//! \b SYSCTL_PERIPH_ONEWIRE0,
//! \b SYSCTL_PERIPH_PWM0, \b SYSCTL_PERIPH_PWM1, \b SYSCTL_PERIPH_QEI0,
//! \b SYSCTL_PERIPH_QEI1, \b SYSCTL_PERIPH_SSI0, \b SYSCTL_PERIPH_SSI1,
//! \b SYSCTL_PERIPH_SSI2, \b SYSCTL_PERIPH_SSI3, \b SYSCTL_PERIPH_TIMER0,
//! \b SYSCTL_PERIPH_TIMER1, \b SYSCTL_PERIPH_TIMER2, \b SYSCTL_PERIPH_TIMER3,
//! \b SYSCTL_PERIPH_TIMER4, \b SYSCTL_PERIPH_TIMER5, \b SYSCTL_PERIPH_TIMER6,
//! \b SYSCTL_PERIPH_TIMER7, \b SYSCTL_PERIPH_UART0, \b SYSCTL_PERIPH_UART1,
//! \b SYSCTL_PERIPH_UART2, \b SYSCTL_PERIPH_UART3, \b SYSCTL_PERIPH_UART4,
//! \b SYSCTL_PERIPH_UART5, \b SYSCTL_PERIPH_UART6, \b SYSCTL_PERIPH_UART7,
//! \b SYSCTL_PERIPH_UDMA, \b SYSCTL_PERIPH_USB0, \b SYSCTL_PERIPH_WDOG0,
//! \b SYSCTL_PERIPH_WDOG1, \b SYSCTL_PERIPH_WTIMER0, \b SYSCTL_PERIPH_WTIMER1,
//! \b SYSCTL_PERIPH_WTIMER2, \b SYSCTL_PERIPH_WTIMER3,
//! \b SYSCTL_PERIPH_WTIMER4, or \b SYSCTL_PERIPH_WTIMER5
//!
//! \note It takes five clock cycles after the write to enable a peripheral
//! before the the peripheral is actually enabled. During this time, attempts
//! to access the peripheral result in a bus fault. Care should be taken
//! to ensure that the peripheral is not accessed during this brief time
//! period.
//!
//! \return None.
//
//*****************************************************************************
void
SysCtlPeripheralEnable(uint32_t ui32Peripheral)
{
//
// Check the arguments.
//
ASSERT(_SysCtlPeripheralValid(ui32Peripheral));
//
// Enable this peripheral.
//
HWREGBITW(SYSCTL_RCGCBASE + ((ui32Peripheral & 0xff00) >> 8),
ui32Peripheral & 0xff) = 1;
}
//*****************************************************************************
//
//! Disables a peripheral.
//!
//! \param ui32Peripheral is the peripheral to disable.
//!
//! This function disables a peripheral. Once disabled, they do not operate or
//! respond to register reads/writes.
//!
//! The \e ui32Peripheral parameter must be only one of the following values:
//! \b SYSCTL_PERIPH_ADC0, \b SYSCTL_PERIPH_ADC1, \b SYSCTL_PERIPH_CAN0,
//! \b SYSCTL_PERIPH_CAN1, \b SYSCTL_PERIPH_CCM0,\b SYSCTL_PERIPH_COMP0,
//! \b SYSCTL_PERIPH_EEPROM0, \b SYSCTL_PERIPH_EMAC, \b SYSCTL_PERIPH_EPHY,
//! \b SYSCTL_PERIPH_EPI0,
//! \b SYSCTL_PERIPH_GPIOA, \b SYSCTL_PERIPH_GPIOB, \b SYSCTL_PERIPH_GPIOC,
//! \b SYSCTL_PERIPH_GPIOD, \b SYSCTL_PERIPH_GPIOE, \b SYSCTL_PERIPH_GPIOF,
//! \b SYSCTL_PERIPH_GPIOG, \b SYSCTL_PERIPH_GPIOH, \b SYSCTL_PERIPH_GPIOJ,
//! \b SYSCTL_PERIPH_GPIOK, \b SYSCTL_PERIPH_GPIOL, \b SYSCTL_PERIPH_GPIOM,
//! \b SYSCTL_PERIPH_GPION, \b SYSCTL_PERIPH_GPIOP, \b SYSCTL_PERIPH_GPIOQ,
//! \b SYSCTL_PERIPH_GPIOR, \b SYSCTL_PERIPH_GPIOS, \b SYSCTL_PERIPH_GPIOT,
//! \b SYSCTL_PERIPH_HIBERNATE,
//! \b SYSCTL_PERIPH_I2C0, \b SYSCTL_PERIPH_I2C1, \b SYSCTL_PERIPH_I2C2,
//! \b SYSCTL_PERIPH_I2C3, \b SYSCTL_PERIPH_I2C4, \b SYSCTL_PERIPH_I2C5,
//! \b SYSCTL_PERIPH_I2C6, \b SYSCTL_PERIPH_I2C7, \b SYSCTL_PERIPH_I2C8,
//! \b SYSCTL_PERIPH_I2C9, \b SYSCTL_PERIPH_LCD0,
//! \b SYSCTL_PERIPH_ONEWIRE0,
//! \b SYSCTL_PERIPH_PWM0, \b SYSCTL_PERIPH_PWM1, \b SYSCTL_PERIPH_QEI0,
//! \b SYSCTL_PERIPH_QEI1, \b SYSCTL_PERIPH_SSI0, \b SYSCTL_PERIPH_SSI1,
//! \b SYSCTL_PERIPH_SSI2, \b SYSCTL_PERIPH_SSI3, \b SYSCTL_PERIPH_TIMER0,
//! \b SYSCTL_PERIPH_TIMER1, \b SYSCTL_PERIPH_TIMER2, \b SYSCTL_PERIPH_TIMER3,
//! \b SYSCTL_PERIPH_TIMER4, \b SYSCTL_PERIPH_TIMER5, \b SYSCTL_PERIPH_TIMER6,
//! \b SYSCTL_PERIPH_TIMER7, \b SYSCTL_PERIPH_UART0, \b SYSCTL_PERIPH_UART1,
//! \b SYSCTL_PERIPH_UART2, \b SYSCTL_PERIPH_UART3, \b SYSCTL_PERIPH_UART4,
//! \b SYSCTL_PERIPH_UART5, \b SYSCTL_PERIPH_UART6, \b SYSCTL_PERIPH_UART7,
//! \b SYSCTL_PERIPH_UDMA, \b SYSCTL_PERIPH_USB0, \b SYSCTL_PERIPH_WDOG0,
//! \b SYSCTL_PERIPH_WDOG1, \b SYSCTL_PERIPH_WTIMER0, \b SYSCTL_PERIPH_WTIMER1,
//! \b SYSCTL_PERIPH_WTIMER2, \b SYSCTL_PERIPH_WTIMER3,
//! \b SYSCTL_PERIPH_WTIMER4, or \b SYSCTL_PERIPH_WTIMER5
//!
//! \return None.
//
//*****************************************************************************
void
SysCtlPeripheralDisable(uint32_t ui32Peripheral)
{
//
// Check the arguments.
//
ASSERT(_SysCtlPeripheralValid(ui32Peripheral));
//
// Disable this peripheral.
//
HWREGBITW(SYSCTL_RCGCBASE + ((ui32Peripheral & 0xff00) >> 8),
ui32Peripheral & 0xff) = 0;
}
//*****************************************************************************
//
//! Enables a peripheral in sleep mode.
//!
//! \param ui32Peripheral is the peripheral to enable in sleep mode.
//!
//! This function allows a peripheral to continue operating when the processor
//! goes into sleep mode. Because the clocking configuration of the device
//! does not change, any peripheral can safely continue operating while the
//! processor is in sleep mode and can therefore wake the processor from sleep
//! mode.
//!
//! Sleep mode clocking of peripherals must be enabled via
//! SysCtlPeripheralClockGating(); if disabled, the peripheral sleep mode
//! configuration is maintained but has no effect when sleep mode is entered.
//!
//! The \e ui32Peripheral parameter must be only one of the following values:
//! \b SYSCTL_PERIPH_ADC0, \b SYSCTL_PERIPH_ADC1, \b SYSCTL_PERIPH_CAN0,
//! \b SYSCTL_PERIPH_CAN1, \b SYSCTL_PERIPH_CCM0,\b SYSCTL_PERIPH_COMP0,
//! \b SYSCTL_PERIPH_EEPROM0, \b SYSCTL_PERIPH_EMAC, \b SYSCTL_PERIPH_EPHY,
//! \b SYSCTL_PERIPH_EPI0,
//! \b SYSCTL_PERIPH_GPIOA, \b SYSCTL_PERIPH_GPIOB, \b SYSCTL_PERIPH_GPIOC,
//! \b SYSCTL_PERIPH_GPIOD, \b SYSCTL_PERIPH_GPIOE, \b SYSCTL_PERIPH_GPIOF,
//! \b SYSCTL_PERIPH_GPIOG, \b SYSCTL_PERIPH_GPIOH, \b SYSCTL_PERIPH_GPIOJ,
//! \b SYSCTL_PERIPH_GPIOK, \b SYSCTL_PERIPH_GPIOL, \b SYSCTL_PERIPH_GPIOM,
//! \b SYSCTL_PERIPH_GPION, \b SYSCTL_PERIPH_GPIOP, \b SYSCTL_PERIPH_GPIOQ,
//! \b SYSCTL_PERIPH_GPIOR, \b SYSCTL_PERIPH_GPIOS, \b SYSCTL_PERIPH_GPIOT,
//! \b SYSCTL_PERIPH_HIBERNATE,
//! \b SYSCTL_PERIPH_I2C0, \b SYSCTL_PERIPH_I2C1, \b SYSCTL_PERIPH_I2C2,
//! \b SYSCTL_PERIPH_I2C3, \b SYSCTL_PERIPH_I2C4, \b SYSCTL_PERIPH_I2C5,
//! \b SYSCTL_PERIPH_I2C6, \b SYSCTL_PERIPH_I2C7, \b SYSCTL_PERIPH_I2C8,
//! \b SYSCTL_PERIPH_I2C9, \b SYSCTL_PERIPH_LCD0,
//! \b SYSCTL_PERIPH_ONEWIRE0,
//! \b SYSCTL_PERIPH_PWM0, \b SYSCTL_PERIPH_PWM1, \b SYSCTL_PERIPH_QEI0,
//! \b SYSCTL_PERIPH_QEI1, \b SYSCTL_PERIPH_SSI0, \b SYSCTL_PERIPH_SSI1,
//! \b SYSCTL_PERIPH_SSI2, \b SYSCTL_PERIPH_SSI3, \b SYSCTL_PERIPH_TIMER0,
//! \b SYSCTL_PERIPH_TIMER1, \b SYSCTL_PERIPH_TIMER2, \b SYSCTL_PERIPH_TIMER3,
//! \b SYSCTL_PERIPH_TIMER4, \b SYSCTL_PERIPH_TIMER5, \b SYSCTL_PERIPH_TIMER6,
//! \b SYSCTL_PERIPH_TIMER7, \b SYSCTL_PERIPH_UART0, \b SYSCTL_PERIPH_UART1,
//! \b SYSCTL_PERIPH_UART2, \b SYSCTL_PERIPH_UART3, \b SYSCTL_PERIPH_UART4,
//! \b SYSCTL_PERIPH_UART5, \b SYSCTL_PERIPH_UART6, \b SYSCTL_PERIPH_UART7,
//! \b SYSCTL_PERIPH_UDMA, \b SYSCTL_PERIPH_USB0, \b SYSCTL_PERIPH_WDOG0,
//! \b SYSCTL_PERIPH_WDOG1, \b SYSCTL_PERIPH_WTIMER0, \b SYSCTL_PERIPH_WTIMER1,
//! \b SYSCTL_PERIPH_WTIMER2, \b SYSCTL_PERIPH_WTIMER3,
//! \b SYSCTL_PERIPH_WTIMER4, or \b SYSCTL_PERIPH_WTIMER5
//!
//! \return None.
//
//*****************************************************************************
void
SysCtlPeripheralSleepEnable(uint32_t ui32Peripheral)
{
//
// Check the arguments.
//
ASSERT(_SysCtlPeripheralValid(ui32Peripheral));
//
// Enable this peripheral in sleep mode.
//
HWREGBITW(SYSCTL_SCGCBASE + ((ui32Peripheral & 0xff00) >> 8),
ui32Peripheral & 0xff) = 1;
}
//*****************************************************************************
//
//! Disables a peripheral in sleep mode.
//!
//! \param ui32Peripheral is the peripheral to disable in sleep mode.
//!
//! This function causes a peripheral to stop operating when the processor goes
//! into sleep mode. Disabling peripherals while in sleep mode helps to lower
//! the current draw of the device. If enabled (via SysCtlPeripheralEnable()),
//! the peripheral automatically resumes operation when the processor
//! leaves sleep mode, maintaining its entire state from before sleep mode was
//! entered.
//!
//! Sleep mode clocking of peripherals must be enabled via
//! SysCtlPeripheralClockGating(); if disabled, the peripheral sleep mode
//! configuration is maintained but has no effect when sleep mode is entered.
//!
//! The \e ui32Peripheral parameter must be only one of the following values:
//! \b SYSCTL_PERIPH_ADC0, \b SYSCTL_PERIPH_ADC1, \b SYSCTL_PERIPH_CAN0,
//! \b SYSCTL_PERIPH_CAN1, \b SYSCTL_PERIPH_CCM0,\b SYSCTL_PERIPH_COMP0,
//! \b SYSCTL_PERIPH_EEPROM0, \b SYSCTL_PERIPH_EMAC, \b SYSCTL_PERIPH_EPHY,
//! \b SYSCTL_PERIPH_EPI0,
//! \b SYSCTL_PERIPH_GPIOA, \b SYSCTL_PERIPH_GPIOB, \b SYSCTL_PERIPH_GPIOC,
//! \b SYSCTL_PERIPH_GPIOD, \b SYSCTL_PERIPH_GPIOE, \b SYSCTL_PERIPH_GPIOF,
//! \b SYSCTL_PERIPH_GPIOG, \b SYSCTL_PERIPH_GPIOH, \b SYSCTL_PERIPH_GPIOJ,
//! \b SYSCTL_PERIPH_GPIOK, \b SYSCTL_PERIPH_GPIOL, \b SYSCTL_PERIPH_GPIOM,
//! \b SYSCTL_PERIPH_GPION, \b SYSCTL_PERIPH_GPIOP, \b SYSCTL_PERIPH_GPIOQ,
//! \b SYSCTL_PERIPH_GPIOR, \b SYSCTL_PERIPH_GPIOS, \b SYSCTL_PERIPH_GPIOT,
//! \b SYSCTL_PERIPH_HIBERNATE,
//! \b SYSCTL_PERIPH_I2C0, \b SYSCTL_PERIPH_I2C1, \b SYSCTL_PERIPH_I2C2,
//! \b SYSCTL_PERIPH_I2C3, \b SYSCTL_PERIPH_I2C4, \b SYSCTL_PERIPH_I2C5,
//! \b SYSCTL_PERIPH_I2C6, \b SYSCTL_PERIPH_I2C7, \b SYSCTL_PERIPH_I2C8,
//! \b SYSCTL_PERIPH_I2C9, \b SYSCTL_PERIPH_LCD0,
//! \b SYSCTL_PERIPH_ONEWIRE0,
//! \b SYSCTL_PERIPH_PWM0, \b SYSCTL_PERIPH_PWM1, \b SYSCTL_PERIPH_QEI0,
//! \b SYSCTL_PERIPH_QEI1, \b SYSCTL_PERIPH_SSI0, \b SYSCTL_PERIPH_SSI1,
//! \b SYSCTL_PERIPH_SSI2, \b SYSCTL_PERIPH_SSI3, \b SYSCTL_PERIPH_TIMER0,
//! \b SYSCTL_PERIPH_TIMER1, \b SYSCTL_PERIPH_TIMER2, \b SYSCTL_PERIPH_TIMER3,
//! \b SYSCTL_PERIPH_TIMER4, \b SYSCTL_PERIPH_TIMER5, \b SYSCTL_PERIPH_TIMER6,
//! \b SYSCTL_PERIPH_TIMER7, \b SYSCTL_PERIPH_UART0, \b SYSCTL_PERIPH_UART1,
//! \b SYSCTL_PERIPH_UART2, \b SYSCTL_PERIPH_UART3, \b SYSCTL_PERIPH_UART4,
//! \b SYSCTL_PERIPH_UART5, \b SYSCTL_PERIPH_UART6, \b SYSCTL_PERIPH_UART7,
//! \b SYSCTL_PERIPH_UDMA, \b SYSCTL_PERIPH_USB0, \b SYSCTL_PERIPH_WDOG0,
//! \b SYSCTL_PERIPH_WDOG1, \b SYSCTL_PERIPH_WTIMER0, \b SYSCTL_PERIPH_WTIMER1,
//! \b SYSCTL_PERIPH_WTIMER2, \b SYSCTL_PERIPH_WTIMER3,
//! \b SYSCTL_PERIPH_WTIMER4, or \b SYSCTL_PERIPH_WTIMER5
//!
//! \return None.
//
//*****************************************************************************
void
SysCtlPeripheralSleepDisable(uint32_t ui32Peripheral)
{
//
// Check the arguments.
//
ASSERT(_SysCtlPeripheralValid(ui32Peripheral));
//
// Disable this peripheral in sleep mode.
//
HWREGBITW(SYSCTL_SCGCBASE + ((ui32Peripheral & 0xff00) >> 8),
ui32Peripheral & 0xff) = 0;
}
//*****************************************************************************
//
//! Enables a peripheral in deep-sleep mode.
//!
//! \param ui32Peripheral is the peripheral to enable in deep-sleep mode.
//!
//! This function allows a peripheral to continue operating when the processor
//! goes into deep-sleep mode. Because the clocking configuration of the
//! device may change, not all peripherals can safely continue operating while
//! the processor is in deep-sleep mode. Those that must run at a particular
//! frequency (such as a UART) do not work as expected if the clock changes.
//! It is the responsibility of the caller to make sensible choices.
//!
//! Deep-sleep mode clocking of peripherals must be enabled via
//! SysCtlPeripheralClockGating(); if disabled, the peripheral deep-sleep mode
//! configuration is maintained but has no effect when deep-sleep mode is
//! entered.
//!
//! The \e ui32Peripheral parameter must be only one of the following values:
//! \b SYSCTL_PERIPH_ADC0, \b SYSCTL_PERIPH_ADC1, \b SYSCTL_PERIPH_CAN0,
//! \b SYSCTL_PERIPH_CAN1, \b SYSCTL_PERIPH_CCM0,\b SYSCTL_PERIPH_COMP0,
//! \b SYSCTL_PERIPH_EEPROM0, \b SYSCTL_PERIPH_EMAC, \b SYSCTL_PERIPH_EPHY,
//! \b SYSCTL_PERIPH_EPI0,
//! \b SYSCTL_PERIPH_GPIOA, \b SYSCTL_PERIPH_GPIOB, \b SYSCTL_PERIPH_GPIOC,
//! \b SYSCTL_PERIPH_GPIOD, \b SYSCTL_PERIPH_GPIOE, \b SYSCTL_PERIPH_GPIOF,
//! \b SYSCTL_PERIPH_GPIOG, \b SYSCTL_PERIPH_GPIOH, \b SYSCTL_PERIPH_GPIOJ,
//! \b SYSCTL_PERIPH_GPIOK, \b SYSCTL_PERIPH_GPIOL, \b SYSCTL_PERIPH_GPIOM,
//! \b SYSCTL_PERIPH_GPION, \b SYSCTL_PERIPH_GPIOP, \b SYSCTL_PERIPH_GPIOQ,
//! \b SYSCTL_PERIPH_GPIOR, \b SYSCTL_PERIPH_GPIOS, \b SYSCTL_PERIPH_GPIOT,
//! \b SYSCTL_PERIPH_HIBERNATE,
//! \b SYSCTL_PERIPH_I2C0, \b SYSCTL_PERIPH_I2C1, \b SYSCTL_PERIPH_I2C2,
//! \b SYSCTL_PERIPH_I2C3, \b SYSCTL_PERIPH_I2C4, \b SYSCTL_PERIPH_I2C5,
//! \b SYSCTL_PERIPH_I2C6, \b SYSCTL_PERIPH_I2C7, \b SYSCTL_PERIPH_I2C8,
//! \b SYSCTL_PERIPH_I2C9, \b SYSCTL_PERIPH_LCD0,
//! \b SYSCTL_PERIPH_ONEWIRE0,
//! \b SYSCTL_PERIPH_PWM0, \b SYSCTL_PERIPH_PWM1, \b SYSCTL_PERIPH_QEI0,
//! \b SYSCTL_PERIPH_QEI1, \b SYSCTL_PERIPH_SSI0, \b SYSCTL_PERIPH_SSI1,
//! \b SYSCTL_PERIPH_SSI2, \b SYSCTL_PERIPH_SSI3, \b SYSCTL_PERIPH_TIMER0,
//! \b SYSCTL_PERIPH_TIMER1, \b SYSCTL_PERIPH_TIMER2, \b SYSCTL_PERIPH_TIMER3,
//! \b SYSCTL_PERIPH_TIMER4, \b SYSCTL_PERIPH_TIMER5, \b SYSCTL_PERIPH_TIMER6,
//! \b SYSCTL_PERIPH_TIMER7, \b SYSCTL_PERIPH_UART0, \b SYSCTL_PERIPH_UART1,
//! \b SYSCTL_PERIPH_UART2, \b SYSCTL_PERIPH_UART3, \b SYSCTL_PERIPH_UART4,
//! \b SYSCTL_PERIPH_UART5, \b SYSCTL_PERIPH_UART6, \b SYSCTL_PERIPH_UART7,
//! \b SYSCTL_PERIPH_UDMA, \b SYSCTL_PERIPH_USB0, \b SYSCTL_PERIPH_WDOG0,
//! \b SYSCTL_PERIPH_WDOG1, \b SYSCTL_PERIPH_WTIMER0, \b SYSCTL_PERIPH_WTIMER1,
//! \b SYSCTL_PERIPH_WTIMER2, \b SYSCTL_PERIPH_WTIMER3,
//! \b SYSCTL_PERIPH_WTIMER4, or \b SYSCTL_PERIPH_WTIMER5
//!
//! \return None.
//
//*****************************************************************************
void
SysCtlPeripheralDeepSleepEnable(uint32_t ui32Peripheral)
{
//
// Check the arguments.
//
ASSERT(_SysCtlPeripheralValid(ui32Peripheral));
//
// Enable this peripheral in deep-sleep mode.
//
HWREGBITW(SYSCTL_DCGCBASE + ((ui32Peripheral & 0xff00) >> 8),
ui32Peripheral & 0xff) = 1;
}
//*****************************************************************************
//
//! Disables a peripheral in deep-sleep mode.
//!
//! \param ui32Peripheral is the peripheral to disable in deep-sleep mode.
//!
//! This function causes a peripheral to stop operating when the processor goes
//! into deep-sleep mode. Disabling peripherals while in deep-sleep mode helps
//! to lower the current draw of the device, and can keep peripherals that
//! require a particular clock frequency from operating when the clock changes
//! as a result of entering deep-sleep mode. If enabled (via
//! SysCtlPeripheralEnable()), the peripheral automatically resumes
//! operation when the processor leaves deep-sleep mode, maintaining its entire
//! state from before deep-sleep mode was entered.
//!
//! Deep-sleep mode clocking of peripherals must be enabled via
//! SysCtlPeripheralClockGating(); if disabled, the peripheral deep-sleep mode
//! configuration is maintained but has no effect when deep-sleep mode is
//! entered.
//!
//! The \e ui32Peripheral parameter must be only one of the following values:
//! \b SYSCTL_PERIPH_ADC0, \b SYSCTL_PERIPH_ADC1, \b SYSCTL_PERIPH_CAN0,
//! \b SYSCTL_PERIPH_CAN1, \b SYSCTL_PERIPH_CCM0,\b SYSCTL_PERIPH_COMP0,
//! \b SYSCTL_PERIPH_EEPROM0, \b SYSCTL_PERIPH_EMAC, \b SYSCTL_PERIPH_EPHY,
//! \b SYSCTL_PERIPH_EPI0,
//! \b SYSCTL_PERIPH_GPIOA, \b SYSCTL_PERIPH_GPIOB, \b SYSCTL_PERIPH_GPIOC,
//! \b SYSCTL_PERIPH_GPIOD, \b SYSCTL_PERIPH_GPIOE, \b SYSCTL_PERIPH_GPIOF,
//! \b SYSCTL_PERIPH_GPIOG, \b SYSCTL_PERIPH_GPIOH, \b SYSCTL_PERIPH_GPIOJ,
//! \b SYSCTL_PERIPH_GPIOK, \b SYSCTL_PERIPH_GPIOL, \b SYSCTL_PERIPH_GPIOM,
//! \b SYSCTL_PERIPH_GPION, \b SYSCTL_PERIPH_GPIOP, \b SYSCTL_PERIPH_GPIOQ,
//! \b SYSCTL_PERIPH_GPIOR, \b SYSCTL_PERIPH_GPIOS, \b SYSCTL_PERIPH_GPIOT,
//! \b SYSCTL_PERIPH_HIBERNATE,
//! \b SYSCTL_PERIPH_I2C0, \b SYSCTL_PERIPH_I2C1, \b SYSCTL_PERIPH_I2C2,
//! \b SYSCTL_PERIPH_I2C3, \b SYSCTL_PERIPH_I2C4, \b SYSCTL_PERIPH_I2C5,
//! \b SYSCTL_PERIPH_I2C6, \b SYSCTL_PERIPH_I2C7, \b SYSCTL_PERIPH_I2C8,
//! \b SYSCTL_PERIPH_I2C9, \b SYSCTL_PERIPH_LCD0,
//! \b SYSCTL_PERIPH_ONEWIRE0,
//! \b SYSCTL_PERIPH_PWM0, \b SYSCTL_PERIPH_PWM1, \b SYSCTL_PERIPH_QEI0,
//! \b SYSCTL_PERIPH_QEI1, \b SYSCTL_PERIPH_SSI0, \b SYSCTL_PERIPH_SSI1,
//! \b SYSCTL_PERIPH_SSI2, \b SYSCTL_PERIPH_SSI3, \b SYSCTL_PERIPH_TIMER0,
//! \b SYSCTL_PERIPH_TIMER1, \b SYSCTL_PERIPH_TIMER2, \b SYSCTL_PERIPH_TIMER3,
//! \b SYSCTL_PERIPH_TIMER4, \b SYSCTL_PERIPH_TIMER5, \b SYSCTL_PERIPH_TIMER6,
//! \b SYSCTL_PERIPH_TIMER7, \b SYSCTL_PERIPH_UART0, \b SYSCTL_PERIPH_UART1,
//! \b SYSCTL_PERIPH_UART2, \b SYSCTL_PERIPH_UART3, \b SYSCTL_PERIPH_UART4,
//! \b SYSCTL_PERIPH_UART5, \b SYSCTL_PERIPH_UART6, \b SYSCTL_PERIPH_UART7,
//! \b SYSCTL_PERIPH_UDMA, \b SYSCTL_PERIPH_USB0, \b SYSCTL_PERIPH_WDOG0,
//! \b SYSCTL_PERIPH_WDOG1, \b SYSCTL_PERIPH_WTIMER0, \b SYSCTL_PERIPH_WTIMER1,
//! \b SYSCTL_PERIPH_WTIMER2, \b SYSCTL_PERIPH_WTIMER3,
//! \b SYSCTL_PERIPH_WTIMER4, or \b SYSCTL_PERIPH_WTIMER5
//!
//! \return None.
//
//*****************************************************************************
void
SysCtlPeripheralDeepSleepDisable(uint32_t ui32Peripheral)
{
//
// Check the arguments.
//
ASSERT(_SysCtlPeripheralValid(ui32Peripheral));
//
// Disable this peripheral in deep-sleep mode.
//
HWREGBITW(SYSCTL_DCGCBASE + ((ui32Peripheral & 0xff00) >> 8),
ui32Peripheral & 0xff) = 0;
}
//*****************************************************************************
//
//! Controls peripheral clock gating in sleep and deep-sleep mode.
//!
//! \param bEnable is a boolean that is \b true if the sleep and deep-sleep
//! peripheral configuration should be used and \b false if not.
//!
//! This function controls how peripherals are clocked when the processor goes
//! into sleep or deep-sleep mode. By default, the peripherals are clocked the
//! same as in run mode; if peripheral clock gating is enabled, they are
//! clocked according to the configuration set by
//! SysCtlPeripheralSleepEnable(), SysCtlPeripheralSleepDisable(),
//! SysCtlPeripheralDeepSleepEnable(), and SysCtlPeripheralDeepSleepDisable().
//!
//! \return None.
//
//*****************************************************************************
void
SysCtlPeripheralClockGating(bool bEnable)
{
if(CLASS_IS_TM4C123)
{
//
// Enable peripheral clock gating as requested.
//
if(bEnable)
{
HWREG(SYSCTL_RCC) |= SYSCTL_RCC_ACG;
}
else
{
HWREG(SYSCTL_RCC) &= ~(SYSCTL_RCC_ACG);
}
}
else
{
//
// Enable peripheral clock gating as requested.
//
if(bEnable)
{
HWREG(SYSCTL_RSCLKCFG) |= SYSCTL_RSCLKCFG_ACG;
}
else
{
HWREG(SYSCTL_RSCLKCFG) &= ~SYSCTL_RSCLKCFG_ACG;
}
}
}
//*****************************************************************************
//
//! Registers an interrupt handler for the system control interrupt.
//!
//! \param pfnHandler is a pointer to the function to be called when the system
//! control interrupt occurs.
//!
//! This function registers the handler to be called when a system control
//! interrupt occurs. This function enables the global interrupt in the
//! interrupt controller; specific system control interrupts must be enabled
//! via SysCtlIntEnable(). It is the interrupt handler's responsibility to
//! clear the interrupt source via SysCtlIntClear().
//!
//! System control can generate interrupts when the PLL achieves lock, if the
//! internal LDO current limit is exceeded, if the internal oscillator fails,
//! if the main oscillator fails, if the internal LDO output voltage droops too
//! much, if the external voltage droops too much, or if the PLL fails.
//!
//! \sa IntRegister() for important information about registering interrupt
//! handlers.
//!
//! \note The events that cause system control interrupts vary based on the
//! Tiva part in use. Please consult the data sheet for the part you are
//! using to determine which interrupt sources are available.
//!
//! \return None.
//
//*****************************************************************************
void
SysCtlIntRegister(void (*pfnHandler)(void))
{
//
// Register the interrupt handler, returning an error if an error occurs.
//
IntRegister(INT_SYSCTL_TM4C123, pfnHandler);
//
// Enable the system control interrupt.
//
IntEnable(INT_SYSCTL_TM4C123);
}
//*****************************************************************************
//
//! Unregisters the interrupt handler for the system control interrupt.
//!
//! This function unregisters the handler to be called when a system control
//! interrupt occurs. This function also masks off the interrupt in the
//! interrupt controller so that the interrupt handler no longer is called.
//!
//! \sa IntRegister() for important information about registering interrupt
//! handlers.
//!
//! \return None.
//
//*****************************************************************************
void
SysCtlIntUnregister(void)
{
//
// Disable the interrupt.
//
IntDisable(INT_SYSCTL_TM4C123);
//
// Unregister the interrupt handler.
//
IntUnregister(INT_SYSCTL_TM4C123);
}
//*****************************************************************************
//
//! Enables individual system control interrupt sources.
//!
//! \param ui32Ints is a bit mask of the interrupt sources to be enabled. Must
//! be a logical OR of \b SYSCTL_INT_BOR0, \b SYSCTL_INT_VDDA_OK,
//! \b SYSCTL_INT_MOSC_PUP, \b SYSCTL_INT_USBPLL_LOCK,
//! \b SYSCTL_INT_PLL_LOCK, \b SYSCTL_INT_MOSC_FAIL, \b SYSCTL_INT_BOR, and/or
//! \b SYSCTL_INT_BOR1.
//!
//! This function enables the indicated system control interrupt sources. Only
//! the sources that are enabled can be reflected to the processor interrupt;
//! disabled sources have no effect on the processor.
//!
//! \note The interrupt sources vary based on the Tiva part in use.
//! Please consult the data sheet for the part you are using to determine
//! which interrupt sources are available.
//!
//! \return None.
//
//*****************************************************************************
void
SysCtlIntEnable(uint32_t ui32Ints)
{
//
// Enable the specified interrupts.
//
HWREG(SYSCTL_IMC) |= ui32Ints;
}
//*****************************************************************************
//
//! Disables individual system control interrupt sources.
//!
//! \param ui32Ints is a bit mask of the interrupt sources to be disabled.
//! Must be a logical OR of \b SYSCTL_INT_BOR0, \b SYSCTL_INT_VDDA_OK,
//! \b SYSCTL_INT_MOSC_PUP, \b SYSCTL_INT_USBPLL_LOCK,
//! \b SYSCTL_INT_PLL_LOCK, \b SYSCTL_INT_MOSC_FAIL, \b SYSCTL_INT_BOR, and/or
//! \b SYSCTL_INT_BOR1.
//!
//! This function disables the indicated system control interrupt sources.
//! Only the sources that are enabled can be reflected to the processor
//! interrupt; disabled sources have no effect on the processor.
//!
//! \note The interrupt sources vary based on the Tiva part in use.
//! Please consult the data sheet for the part you are using to determine
//! which interrupt sources are available.
//!
//! \return None.
//
//*****************************************************************************
void
SysCtlIntDisable(uint32_t ui32Ints)
{
//
// Disable the specified interrupts.
//
HWREG(SYSCTL_IMC) &= ~(ui32Ints);
}
//*****************************************************************************
//
//! Clears system control interrupt sources.
//!
//! \param ui32Ints is a bit mask of the interrupt sources to be cleared. Must
//! be a logical OR of \b SYSCTL_INT_BOR0, \b SYSCTL_INT_VDDA_OK,
//! \b SYSCTL_INT_MOSC_PUP, \b SYSCTL_INT_USBPLL_LOCK,
//! \b SYSCTL_INT_PLL_LOCK, \b SYSCTL_INT_MOSC_FAIL, \b SYSCTL_INT_BOR, and/or
//! \b SYSCTL_INT_BOR1.
//!
//! The specified system control interrupt sources are cleared, so that they no
//! longer assert. This function must be called in the interrupt handler to
//! keep it from being called again immediately on exit.
//!
//! \note Because there is a write buffer in the Cortex-M processor, it may
//! take several clock cycles before the interrupt source is actually cleared.
//! Therefore, it is recommended that the interrupt source be cleared early in
//! the interrupt handler (as opposed to the very last action) to avoid
//! returning from the interrupt handler before the interrupt source is
//! actually cleared. Failure to do so may result in the interrupt handler
//! being immediately reentered (because the interrupt controller still sees
//! the interrupt source asserted).
//!
//! \note The interrupt sources vary based on the Tiva part in use.
//! Please consult the data sheet for the part you are using to determine
//! which interrupt sources are available.
//!
//! \return None.
//
//*****************************************************************************
void
SysCtlIntClear(uint32_t ui32Ints)
{
//
// Clear the requested interrupt sources.
//
HWREG(SYSCTL_MISC) = ui32Ints;
}
//*****************************************************************************
//
//! Gets the current interrupt status.
//!
//! \param bMasked is false if the raw interrupt status is required and true if
//! the masked interrupt status is required.
//!
//! This function returns the interrupt status for the system controller.
//! Either the raw interrupt status or the status of interrupts that are
//! allowed to reflect to the processor can be returned.
//!
//! \note The interrupt sources vary based on the Tiva part in use.
//! Please consult the data sheet for the part you are using to determine
//! which interrupt sources are available.
//!
//! \return The current interrupt status, enumerated as a bit field of
//! \b SYSCTL_INT_BOR0, \b SYSCTL_INT_VDDA_OK,
//! \b SYSCTL_INT_MOSC_PUP, \b SYSCTL_INT_USBPLL_LOCK,
//! \b SYSCTL_INT_PLL_LOCK, \b SYSCTL_INT_MOSC_FAIL, \b SYSCTL_INT_BOR, and/or
//! \b SYSCTL_INT_BOR1.
//
//*****************************************************************************
uint32_t
SysCtlIntStatus(bool bMasked)
{
//
// Return either the interrupt status or the raw interrupt status as
// requested.
//
if(bMasked)
{
return(HWREG(SYSCTL_MISC));
}
else
{
return(HWREG(SYSCTL_RIS));
}
}
//*****************************************************************************
//
//! Sets the output voltage of the LDO when the device enters sleep mode.
//!
//! \param ui32Voltage is the required output voltage from the LDO while in
//! sleep mode.
//!
//! This function sets the output voltage of the LDO while in sleep mode.
//! The \e ui32Voltage parameter must be one of the following values:
//! \b SYSCTL_LDO_0_90V, \b SYSCTL_LDO_0_95V, \b SYSCTL_LDO_1_00V,
//! \b SYSCTL_LDO_1_05V, \b SYSCTL_LDO_1_10V, \b SYSCTL_LDO_1_15V, or
//! \b SYSCTL_LDO_1_20V.
//!
//! \note The availability of this feature, the default LDO voltage, and the
//! adjustment range varies with the Tiva part in use. Please consult the
//! data sheet for the part you are using to determine whether this support is
//! available.
//!
//! \return None.
//
//*****************************************************************************
void
SysCtlLDOSleepSet(uint32_t ui32Voltage)
{
//
// Check the arguments.
//
ASSERT((ui32Voltage == SYSCTL_LDO_0_90V) ||
(ui32Voltage == SYSCTL_LDO_0_95V) ||
(ui32Voltage == SYSCTL_LDO_1_00V) ||
(ui32Voltage == SYSCTL_LDO_1_05V) ||
(ui32Voltage == SYSCTL_LDO_1_10V) ||
(ui32Voltage == SYSCTL_LDO_1_15V) ||
(ui32Voltage == SYSCTL_LDO_1_20V));
//
// Set the sleep-mode LDO voltage to the requested value.
//
HWREG(SYSCTL_LDOSPCTL) = ui32Voltage;
}
//*****************************************************************************
//
//! Returns the output voltage of the LDO when the device enters sleep mode.
//!
//! This function determines the output voltage of the LDO while in sleep mode,
//! as specified by the control register.
//!
//! \note The availability of this feature, the default LDO voltage, and the
//! adjustment range varies with the Tiva part in use. Please consult the
//! data sheet for the part you are using to determine whether this support is
//! available.
//!
//! \return Returns the sleep-mode voltage of the LDO and is one of
//! \b SYSCTL_LDO_0_90V, \b SYSCTL_LDO_0_95V, \b SYSCTL_LDO_1_00V,
//! \b SYSCTL_LDO_1_05V, \b SYSCTL_LDO_1_10V, \b SYSCTL_LDO_1_15V, or
//! \b SYSCTL_LDO_1_20V.
//
//*****************************************************************************
uint32_t
SysCtlLDOSleepGet(void)
{
//
// Return the sleep-mode LDO voltage setting.
//
return(HWREG(SYSCTL_LDOSPCTL));
}
//*****************************************************************************
//
//! Sets the output voltage of the LDO when the device enters deep-sleep
//! mode.
//!
//! \param ui32Voltage is the required output voltage from the LDO while in
//! deep-sleep mode.
//!
//! This function sets the output voltage of the LDO while in deep-sleep mode.
//! The \e ui32Voltage parameter specifies the output voltage of the LDO and
//! must be one of the following values: \b SYSCTL_LDO_0_90V,
//! \b SYSCTL_LDO_0_95V, \b SYSCTL_LDO_1_00V, \b SYSCTL_LDO_1_05V,
//! \b SYSCTL_LDO_1_10V, \b SYSCTL_LDO_1_15V, or \b SYSCTL_LDO_1_20V.
//!
//! \note The availability of this feature, the default LDO voltage, and the
//! adjustment range varies with the Tiva part in use. Please consult the
//! data sheet for the part you are using to determine whether this support is
//! available.
//!
//! \return None.
//
//*****************************************************************************
void
SysCtlLDODeepSleepSet(uint32_t ui32Voltage)
{
//
// Check the arguments.
//
ASSERT((ui32Voltage == SYSCTL_LDO_0_90V) ||
(ui32Voltage == SYSCTL_LDO_0_95V) ||
(ui32Voltage == SYSCTL_LDO_1_00V) ||
(ui32Voltage == SYSCTL_LDO_1_05V) ||
(ui32Voltage == SYSCTL_LDO_1_10V) ||
(ui32Voltage == SYSCTL_LDO_1_15V) ||
(ui32Voltage == SYSCTL_LDO_1_20V));
//
// Set the deep-sleep LDO voltage to the requested value.
//
HWREG(SYSCTL_LDODPCTL) = ui32Voltage;
}
//*****************************************************************************
//
//! Returns the output voltage of the LDO when the device enters deep-sleep
//! mode.
//!
//! This function returns the output voltage of the LDO when the device is
//! in deep-sleep mode, as specified by the control register.
//!
//! \note The availability of this feature, the default LDO voltage, and the
//! adjustment range varies with the Tiva part in use. Please consult the
//! data sheet for the part you are using to determine whether this support is
//! available.
//!
//! \return Returns the deep-sleep-mode voltage of the LDO; is one of
//! \b SYSCTL_LDO_0_90V, \b SYSCTL_LDO_0_95V, \b SYSCTL_LDO_1_00V,
//! \b SYSCTL_LDO_1_05V, \b SYSCTL_LDO_1_10V, \b SYSCTL_LDO_1_15V, or
//! \b SYSCTL_LDO_1_20V.
//
//*****************************************************************************
uint32_t
SysCtlLDODeepSleepGet(void)
{
//
// Return the deep-sleep-mode LDO voltage setting.
//
return(HWREG(SYSCTL_LDODPCTL));
}
//*****************************************************************************
//
//! Configures the power to the flash and SRAM while in sleep mode.
//!
//! \param ui32Config is the required flash and SRAM power configuration.
//!
//! This function allows the power configuration of the flash and SRAM while in
//! sleep mode to be set. The \e ui32Config parameter is the logical OR of the
//! flash power configuration and the SRAM power configuration.
//!
//! The flash power configuration is specified as either:
//!
//! - \b SYSCTL_FLASH_NORMAL - The flash is left in fully powered mode,
//! providing fast wake-up time but higher power consumption.
//! - \b SYSCTL_FLASH_LOW_POWER - The flash is in low power mode, providing
//! reduced power consumption but longer wake-up time.
//!
//! The SRAM power configuration is specified as one of:
//!
//! - \b SYSCTL_SRAM_NORMAL - The SRAM is left in fully powered mode, providing
//! fast wake-up time but higher power consumption.
//! - \b SYSCTL_SRAM_STANDBY - The SRAM is placed into a lower power mode,
//! providing reduced power consumption but longer wake-up time.
//! - \b SYSCTL_SRAM_LOW_POWER - The SRAM is placed into lowest power mode,
//! providing further reduced power consumption but longer wake-up time.
//!
//! \note The availability of this feature varies with the Tiva part in
//! use. Please consult the data sheet for the part you are using to determine
//! whether this support is available.
//!
//! \return None.
//
//*****************************************************************************
void
SysCtlSleepPowerSet(uint32_t ui32Config)
{
//
// Set the sleep-mode flash and SRAM power configuration.
//
HWREG(SYSCTL_SLPPWRCFG) = ui32Config;
}
//*****************************************************************************
//
//! Configures the power to the flash and SRAM while in deep-sleep mode.
//!
//! \param ui32Config is the required flash and SRAM power configuration.
//!
//! This function allows the power configuration of the flash and SRAM while in
//! deep-sleep mode to be set. The \e ui32Config parameter is the logical OR
//! of the flash power configuration and the SRAM power configuration.
//!
//! The flash power configuration is specified as either:
//!
//! - \b SYSCTL_FLASH_NORMAL - The flash is left in fully powered mode,
//! providing fast wake-up time but higher power consumption.
//! - \b SYSCTL_FLASH_LOW_POWER - The flash is in low power mode, providing
//! reduced power consumption but longer wake-up time.
//!
//! The SRAM power configuration is specified as one of:
//!
//! - \b SYSCTL_LDO_SLEEP - The LDO is in sleep mode.
//! - \b SYSCTL_TEMP_LOW_POWER - The temperature sensor in low power mode.
//! - \b SYSCTL_SRAM_NORMAL - The SRAM is left in fully powered mode, providing
//! fast wake-up time but higher power consumption.
//! - \b SYSCTL_SRAM_STANDBY - The SRAM is placed into a lower power mode,
//! providing reduced power consumption but longer wake-up time.
//! - \b SYSCTL_SRAM_LOW_POWER - The SRAM is placed into lowest power mode,
//! providing further reduced power consumption but longer wake-up time.
//!
//! \note The availability of this feature varies with the Tiva part in
//! use. Please consult the data sheet for the part you are using to determine
//! whether this support is available.
//!
//! \return None.
//
//*****************************************************************************
void
SysCtlDeepSleepPowerSet(uint32_t ui32Config)
{
//
// Set the deep-sleep-mode flash and SRAM power configuration.
//
HWREG(SYSCTL_DSLPPWRCFG) = ui32Config;
}
//*****************************************************************************
//
//! Resets the device.
//!
//! This function performs a software reset of the entire device. The
//! processor and all peripherals are reset and all device registers are
//! returned to their default values (with the exception of the reset cause
//! register, which maintains its current value but has the software reset
//! bit set as well).
//!
//! \return This function does not return.
//
//*****************************************************************************
void
SysCtlReset(void)
{
//
// Perform a software reset request. This request causes the device to
// reset, no further code is executed.
//
HWREG(NVIC_APINT) = NVIC_APINT_VECTKEY | NVIC_APINT_SYSRESETREQ;
//
// The device should have reset, so this should never be reached. Just in
// case, loop forever.
//
while(1)
{
}
}
//*****************************************************************************
//
//! Puts the processor into sleep mode.
//!
//! This function places the processor into sleep mode; it does not return
//! until the processor returns to run mode. The peripherals that are enabled
//! via SysCtlPeripheralSleepEnable() continue to operate and can wake up the
//! processor (if automatic clock gating is enabled with
//! SysCtlPeripheralClockGating(), otherwise all peripherals continue to
//! operate).
//!
//! \return None.
//
//*****************************************************************************
void
SysCtlSleep(void)
{
//
// Wait for an interrupt.
//
CPUwfi();
}
//*****************************************************************************
//
//! Puts the processor into deep-sleep mode.
//!
//! This function places the processor into deep-sleep mode; it does not return
//! until the processor returns to run mode. The peripherals that are enabled
//! via SysCtlPeripheralDeepSleepEnable() continue to operate and can wake up
//! the processor (if automatic clock gating is enabled with
//! SysCtlPeripheralClockGating(), otherwise all peripherals continue to
//! operate).
//!
//! \return None.
//
//*****************************************************************************
void
SysCtlDeepSleep(void)
{
//
// Enable deep-sleep.
//
HWREG(NVIC_SYS_CTRL) |= NVIC_SYS_CTRL_SLEEPDEEP;
//
// Wait for an interrupt.
//
CPUwfi();
//
// Disable deep-sleep so that a future sleep works correctly.
//
HWREG(NVIC_SYS_CTRL) &= ~(NVIC_SYS_CTRL_SLEEPDEEP);
}
//*****************************************************************************
//
//! Gets the reason for a reset.
//!
//! This function returns the reason(s) for a reset. Because the reset
//! reasons are sticky until either cleared by software or a power-on reset,
//! multiple reset reasons may be returned if multiple resets have occurred.
//! The reset reason is a logical OR of \b SYSCTL_CAUSE_HSRVREQ,
//! \b SYSCTL_CAUSE_HIB, \b SYSCTL_CAUSE_WDOG1, \b SYSCTL_CAUSE_SW,
//! \b SYSCTL_CAUSE_WDOG0, \b SYSCTL_CAUSE_BOR, \b SYSCTL_CAUSE_POR,
//! and/or \b SYSCTL_CAUSE_EXT.
//!
//! \return Returns the reason(s) for a reset.
//
//*****************************************************************************
uint32_t
SysCtlResetCauseGet(void)
{
//
// Return the reset reasons.
//
return(HWREG(SYSCTL_RESC));
}
//*****************************************************************************
//
//! Clears reset reasons.
//!
//! \param ui32Causes are the reset causes to be cleared; must be a logical OR
//! of \b SYSCTL_CAUSE_HSRVREQ, \b SYSCTL_CAUSE_HIB, \b SYSCTL_CAUSE_WDOG1,
//! \b SYSCTL_CAUSE_SW, \b SYSCTL_CAUSE_WDOG0, \b SYSCTL_CAUSE_BOR,
//! \b SYSCTL_CAUSE_POR, and/or \b SYSCTL_CAUSE_EXT.
//!
//! This function clears the specified sticky reset reasons. Once cleared,
//! another reset for the same reason can be detected, and a reset for a
//! different reason can be distinguished (instead of having two reset causes
//! set). If the reset reason is used by an application, all reset causes
//! should be cleared after they are retrieved with SysCtlResetCauseGet().
//!
//! \return None.
//
//*****************************************************************************
void
SysCtlResetCauseClear(uint32_t ui32Causes)
{
//
// Clear the given reset reasons.
//
HWREG(SYSCTL_RESC) &= ~(ui32Causes);
}
//*****************************************************************************
//
//! Provides a small delay.
//!
//! \param ui32Count is the number of delay loop iterations to perform.
//!
//! This function provides a means of generating a delay by executing a simple
//! 3 instruction cycle loop a given number of times. It is written in
//! assembly to keep the loop instruction count consistent across tool chains.
//!
//! It is important to note that this function does NOT provide an accurate
//! timing mechanism. Although the delay loop is 3 instruction cycles long,
//! the execution time of the loop will vary dramatically depending upon the
//! application's interrupt environment (the loop will be interrupted unless
//! run with interrupts disabled and this is generally an unwise thing to do)
//! and also the current system clock rate and flash timings (wait states and
//! the operation of the prefetch buffer affect the timing).
//!
//! For better accuracy, the ROM version of this function may be used. This
//! version will not suffer from flash- and prefect buffer-related timing
//! variability but will still be delayed by interrupt service routines.
//!
//! For best accuracy, a system timer should be used with code either polling
//! for a particular timer value being exceeded or processing the timer
//! interrupt to determine when a particular time period has elapsed.
//!
//! \return None.
//
//*****************************************************************************
#if defined(ewarm) || defined(DOXYGEN)
void
SysCtlDelay(uint32_t ui32Count)
{
__asm(" subs r0, #1\n"
" bne.n SysCtlDelay\n"
" bx lr");
}
#endif
#if defined(codered) || defined(gcc) || defined(sourcerygxx)
void __attribute__((naked))
SysCtlDelay(uint32_t ui32Count)
{
__asm(" subs r0, #1\n"
" bne SysCtlDelay\n"
" bx lr");
}
#endif
#if defined(rvmdk) || defined(__ARMCC_VERSION)
__asm void
SysCtlDelay(uint32_t ui32Count)
{
subs r0, #1;
bne SysCtlDelay;
bx lr;
}
#endif
//
// For CCS implement this function in pure assembly. This prevents the TI
// compiler from doing funny things with the optimizer.
//
#if defined(ccs)
__asm(" .sect \".text:SysCtlDelay\"\n"
" .clink\n"
" .thumbfunc SysCtlDelay\n"
" .thumb\n"
" .global SysCtlDelay\n"
"SysCtlDelay:\n"
" subs r0, #1\n"
" bne.n SysCtlDelay\n"
" bx lr\n");
#endif
//*****************************************************************************
//
//! Sets the configuration of the main oscillator (MOSC) control.
//!
//! \param ui32Config is the required configuration of the MOSC control.
//!
//! This function configures the control of the main oscillator. The
//! \e ui32Config is specified as the logical OR of the following values:
//!
//! - \b SYSCTL_MOSC_VALIDATE enables the MOSC verification circuit that
//! detects a failure of the main oscillator (such as a loss of the clock).
//! - \b SYSCTL_MOSC_INTERRUPT indicates that a MOSC failure should generate an
//! interrupt instead of resetting the processor.
//! - \b SYSCTL_MOSC_NO_XTAL indicates that there is no crystal or oscillator
//! connected to the OSC0/OSC1 pins, allowing power consumption to be
//! reduced.
//! - \b SYSCTL_MOSC_PWR_DIS disable power to the main oscillator. If this
//! parameter is not specified, the MOSC input remains powered.
//! - \b SYSCTL_MOSC_LOWFREQ MOSC is less than 10 MHz.
//! - \b SYSCTL_MOSC_HIGHFREQ MOSC is greater than 10 MHz.
//! - \b SYSCTL_MOSC_SESRC specifies that the MOSC is a single-ended
//! oscillator connected to OSC0. If this parameter is not specified, the
//! input is assumed to be a crystal.
//!
//! \note The availability of MOSC control varies based on the Tiva part
//! in use. Please consult the data sheet for the part you are using to
//! determine whether this support is available. In addition, the capability
//! of MOSC control varies based on the Tiva part in use.
//!
//! \return None.
//
//*****************************************************************************
void
SysCtlMOSCConfigSet(uint32_t ui32Config)
{
//
// Configure the MOSC control.
//
HWREG(SYSCTL_MOSCCTL) = ui32Config;
}
//*****************************************************************************
//
//! Calibrates the precision internal oscillator.
//!
//! \param ui32Type is the type of calibration to perform.
//!
//! This function performs a calibration of the PIOSC. There are three types
//! of calibration available; the desired calibration type as specified in
//! \e ui32Type is one of:
//!
//! - \b SYSCTL_PIOSC_CAL_AUTO to perform automatic calibration using the
//! 32-kHz clock from the hibernate module as a reference. This type is
//! only possible on parts that have a hibernate module, and then only if
//! it is enabled, a 32.768-kHz clock source is attached to the XOSC0/1
//! pins and the hibernate module's RTC is also enabled.
//!
//! - \b SYSCTL_PIOSC_CAL_FACT to reset the PIOSC calibration to the factory
//! provided calibration.
//!
//! - \b SYSCTL_PIOSC_CAL_USER to set the PIOSC calibration to a user-supplied
//! value. The value to be used is ORed into the lower 7-bits of this value,
//! with 0x40 being the ``nominal'' value (in other words, if everything were
//! perfect, 0x40 provides exactly 16 MHz). Values larger than 0x40
//! slow down PIOSC, and values smaller than 0x40 speed up PIOSC.
//!
//! \return Returns 1 if the calibration was successful and 0 if it failed.
//
//*****************************************************************************
uint32_t
SysCtlPIOSCCalibrate(uint32_t ui32Type)
{
//
// Perform the requested calibration. If performing user calibration, the
// UTEN bit must be set with one write, then the UT field in a second
// write, and the UPDATE bit in a final write. For other calibration
// types, a single write to set UPDATE or CAL is all that is required.
//
if(ui32Type & (SYSCTL_PIOSCCAL_UTEN | SYSCTL_PIOSCCAL_UPDATE))
{
HWREG(SYSCTL_PIOSCCAL) = ui32Type & SYSCTL_PIOSCCAL_UTEN;
HWREG(SYSCTL_PIOSCCAL) =
ui32Type & (SYSCTL_PIOSCCAL_UTEN | SYSCTL_PIOSCCAL_UT_M);
}
HWREG(SYSCTL_PIOSCCAL) = ui32Type;
//
// See if an automatic calibration was requested.
//
if(ui32Type & SYSCTL_PIOSCCAL_CAL)
{
//
// Wait for the automatic calibration to complete.
//
while((HWREG(SYSCTL_PIOSCSTAT) & SYSCTL_PIOSCSTAT_CR_M) == 0)
{
}
//
// If the automatic calibration failed, return an error.
//
if((HWREG(SYSCTL_PIOSCSTAT) & SYSCTL_PIOSCSTAT_CR_M) !=
SYSCTL_PIOSCSTAT_CRPASS)
{
return(0);
}
}
//
// The calibration was successful.
//
return(1);
}
//*****************************************************************************
//
//! Sets the type of reset issued due to certain reset events.
//!
//! \param ui32Behavior specifies the types of resets for each of the
//! configurable reset events.
//!
//! This function sets the types of reset issued when a configurable reset
//! event occurs. The reset events that are configurable are: Watchdog 0 or 1,
//! a brown out and the external RSTn pin. The valid actions are either a
//! system reset or a full POR sequence. See the data sheet for more
//! information on the differences between a full POR and a system reset. All
//! reset behaviors can be configured with a single call using the logical OR
//! of the values defined below. Any reset option that is not specifically set
//! remains configured for its default behavior. Either POR or system reset
//! can be selected for each reset cause.
//!
//! Valid values are logical combinations of the following:
//!
//! - \b SYSCTL_ONRST_WDOG0_POR configures a Watchdog 0 reset to perform a full
//! POR.
//! - \b SYSCTL_ONRST_WDOG0_SYS configures a Watchdog 0 reset to perform a
//! system reset.
//! - \b SYSCTL_ONRST_WDOG1_POR configures a Watchdog 1 reset to perform a full
//! POR.
//! - \b SYSCTL_ONRST_WDOG1_SYS configures a Watchdog 1 reset to perform a
//! system reset.
//! - \b SYSCTL_ONRST_BOR_POR configures a brown-out reset to perform a full
//! POR.
//! - \b SYSCTL_ONRST_BOR_SYS configures a brown-out reset to perform a system
//! reset.
//! - \b SYSCTL_ONRST_EXT_POR configures an external pin reset to perform a
//! full POR.
//! - \b SYSCTL_ONRST_EXT_SYS configures an external pin reset to perform a
//! system reset.
//!
//! \b Example: Set Watchdog 0 reset to trigger a POR and a brown-out reset
//! to trigger a system reset while leaving the remaining resets with their
//! default behaviors.
//!
//! \verbatim
//! SysCtlResetBehaviorSet(SYSCTL_ONRST_WDOG0_POR | SYSCTL_ONRST_BOR_SYS);
//! \endverbatim
//!
//! \note This function cannot be used with TM4C123 devices.
//!
//! \return None.
//
//*****************************************************************************
void
SysCtlResetBehaviorSet(uint32_t ui32Behavior)
{
HWREG(SYSCTL_RESBEHAVCTL) = ui32Behavior;
}
//*****************************************************************************
//
//! Returns the current types of reset issued due to reset events.
//!
//! This function returns the types of resets issued when a configurable reset
//! occurs. The value returned is a logical OR combination of the valid values
//! that are described in the documentation for the \e ui32Behavior parameter
//! of the SysCtlResetBehaviorSet() function.
//!
//! \note This function should only be used with Flurry-class devices.
//!
//! \return The reset behaviors for all configurable resets.
//
//*****************************************************************************
uint32_t
SysCtlResetBehaviorGet(void)
{
return(HWREG(SYSCTL_RESBEHAVCTL));
}
//*****************************************************************************
//
//! Configures the system clock.
//!
//! \param ui32Config is the required configuration of the device clocking.
//! \param ui32SysClock is the requested processor frequency.
//!
//! This function configures the main system clocking for the device. The
//! input frequency, oscillator source, whether or not to enable the PLL, and
//! the system clock divider are all configured with this function. This
//! function configures the system frequency to the closest available divisor
//! of one of the fixed PLL VCO settings provided in the \e ui32Config
//! parameter. The caller sets the \e ui32SysClock parameter to request the
//! system clock frequency, and this function then attempts to match this using
//! the values provided in the \e ui32Config parameter. If this function
//! cannot exactly match the requested frequency, it picks the closest
//! frequency that is lower than the requested frequency. The \e ui32Config
//! parameter provides the remaining configuration options using a set of
//! defines that are a logical OR of several different values, many of which
//! are grouped into sets where only one of the set can be chosen. This
//! function returns the current system frequency which may not match the
//! requested frequency.
//!
//! The oscillator source is chosen with one of the following values:
//!
//! - \b SYSCTL_OSC_MAIN to use an external crystal or oscillator.
//! - \b SYSCTL_OSC_INT to use the 16-MHz precision internal oscillator.
//! - \b SYSCTL_OSC_INT30 to use the internal low frequency oscillator.
//! - \b SYSCTL_OSC_EXT32 to use the hibernate modules 32.786-kHz oscillator.
//! This option is only available on devices that include the hibernation
//! module.
//!
//! The system clock source is chosen with one of the following values:
//!
//! - \b SYSCTL_USE_PLL is used to select the PLL output as the system clock.
//! - \b SYSCTL_USE_OSC is used to choose one of the oscillators as the
//! system clock.
//!
//! The PLL VCO frequency is chosen with one of the the following values:
//!
//! - \b SYSCTL_CFG_VCO_480 to set the PLL VCO output to 480-MHz
//! - \b SYSCTL_CFG_VCO_320 to set the PLL VCO output to 320-MHz
//!
//! Example: Configure the system clocking to be 40 MHz with a 320-MHz PLL
//! setting using the 16-MHz internal oscillator.
//!
//! \verbatim
//! SysCtlClockFreqSet(SYSCTL_OSC_INT | SYSCTL_USE_PLL | SYSCTL_CFG_VCO_320,
//! 40000000);
//! \endverbatim
//!
//! \note This function cannot be used with TM4C123 devices. For TM4C123
//! devices use the SysCtlClockSet() function.
//!
//! \return The actual configured system clock frequency in Hz or zero if the
//! value could not be changed due to a parameter error or PLL lock failure.
//
//*****************************************************************************
uint32_t
SysCtlClockFreqSet(uint32_t ui32Config, uint32_t ui32SysClock)
{
int32_t i32Timeout, i32VCOIdx, i32XtalIdx;
uint32_t ui32MOSCCTL;
uint32_t ui32SysDiv, ui32Osc, ui32OscSelect, ui32RSClkConfig;
bool bNewPLL;
//
// TM4C123 devices should not use this function.
//
if(CLASS_IS_TM4C123)
{
return(0);
}
//
// Get the index of the crystal from the ui32Config parameter.
//
i32XtalIdx = SysCtlXtalCfgToIndex(ui32Config);
//
// Determine which non-PLL source was selected.
//
if((ui32Config & 0x38) == SYSCTL_OSC_INT)
{
//
// Use the nominal frequency for the PIOSC oscillator and set the
// crystal select.
//
ui32Osc = 16000000;
ui32OscSelect = SYSCTL_RSCLKCFG_OSCSRC_PIOSC;
ui32OscSelect |= SYSCTL_RSCLKCFG_PLLSRC_PIOSC;
//
// Force the crystal index to the value for 16-MHz.
//
i32XtalIdx = SysCtlXtalCfgToIndex(SYSCTL_XTAL_16MHZ);
}
else if((ui32Config & 0x38) == SYSCTL_OSC_INT30)
{
//
// Use the nominal frequency for the low frequency oscillator.
//
ui32Osc = 30000;
ui32OscSelect = SYSCTL_RSCLKCFG_OSCSRC_LFIOSC;
}
else if((ui32Config & 0x38) == (SYSCTL_OSC_EXT32 & 0x38))
{
//
// Use the RTC frequency.
//
ui32Osc = 32768;
ui32OscSelect = SYSCTL_RSCLKCFG_OSCSRC_RTC;
}
else if((ui32Config & 0x38) == SYSCTL_OSC_MAIN)
{
//
// Bounds check the source frequency for the main oscillator. The is
// because the PLL tables in the g_pppui32XTALtoVCO structure range
// from 5MHz to 25MHz.
//
if((i32XtalIdx > (SysCtlXtalCfgToIndex(SYSCTL_XTAL_25MHZ))) ||
(i32XtalIdx < (SysCtlXtalCfgToIndex(SYSCTL_XTAL_5MHZ))))
{
return(0);
}
ui32Osc = g_pui32Xtals[i32XtalIdx];
//
// Set the PLL source select to MOSC.
//
ui32OscSelect = SYSCTL_RSCLKCFG_OSCSRC_MOSC;
ui32OscSelect |= SYSCTL_RSCLKCFG_PLLSRC_MOSC;
//
// Clear MOSC power down, high oscillator range setting, and no crystal
// present setting.
//
ui32MOSCCTL = HWREG(SYSCTL_MOSCCTL) &
~(SYSCTL_MOSCCTL_OSCRNG | SYSCTL_MOSCCTL_PWRDN |
SYSCTL_MOSCCTL_NOXTAL);
//
// Increase the drive strength for MOSC of 10 MHz and above.
//
if(i32XtalIdx >= (SysCtlXtalCfgToIndex(SYSCTL_XTAL_10MHZ) -
(SysCtlXtalCfgToIndex(SYSCTL_XTAL_5MHZ))))
{
ui32MOSCCTL |= SYSCTL_MOSCCTL_OSCRNG;
}
HWREG(SYSCTL_MOSCCTL) = ui32MOSCCTL;
}
else
{
//
// This was an invalid request because no oscillator source was
// indicated.
//
ui32Osc = 0;
ui32OscSelect = SYSCTL_RSCLKCFG_OSCSRC_PIOSC;
}
//
// Check if the running with the PLL enabled was requested.
//
if((ui32Config & SYSCTL_USE_OSC) == SYSCTL_USE_PLL)
{
//
// ui32Config must be SYSCTL_OSC_MAIN or SYSCTL_OSC_INT.
//
if(((ui32Config & 0x38) != SYSCTL_OSC_MAIN) &&
((ui32Config & 0x38) != SYSCTL_OSC_INT))
{
return(0);
}
//
// Get the VCO index out of the ui32Config parameter.
//
i32VCOIdx = (ui32Config >> 24) & 7;
//
// Check that the VCO index is not out of bounds.
//
ASSERT(i32VCOIdx < MAX_VCO_ENTRIES);
//
// Set the memory timings for the maximum external frequency since
// this could be a switch to PIOSC or possibly to MOSC which can be
// up to 25MHz.
//
HWREG(SYSCTL_MEMTIM0) = _SysCtlMemTimingGet(25000000);
//
// Clear the old PLL divider and source in case it was set.
//
ui32RSClkConfig = HWREG(SYSCTL_RSCLKCFG) &
~(SYSCTL_RSCLKCFG_PSYSDIV_M |
SYSCTL_RSCLKCFG_OSCSRC_M |
SYSCTL_RSCLKCFG_PLLSRC_M | SYSCTL_RSCLKCFG_USEPLL);
//
// Update the memory timings to match running from PIOSC.
//
ui32RSClkConfig |= SYSCTL_RSCLKCFG_MEMTIMU;
//
// Update clock configuration to switch back to PIOSC.
//
HWREG(SYSCTL_RSCLKCFG) = ui32RSClkConfig;
//
// The table starts at 5 MHz so modify the index to match this.
//
i32XtalIdx -= SysCtlXtalCfgToIndex(SYSCTL_XTAL_5MHZ);
//
// If there were no changes to the PLL do not force the PLL to lock by
// writing the PLL settings.
//
if((HWREG(SYSCTL_PLLFREQ1) !=
g_pppui32XTALtoVCO[i32VCOIdx][i32XtalIdx][1]) ||
(HWREG(SYSCTL_PLLFREQ0) !=
(g_pppui32XTALtoVCO[i32VCOIdx][i32XtalIdx][0] |
SYSCTL_PLLFREQ0_PLLPWR)))
{
bNewPLL = true;
}
else
{
bNewPLL = false;
}
//
// If there are new PLL settings write them.
//
if(bNewPLL)
{
//
// Set the oscillator source.
//
HWREG(SYSCTL_RSCLKCFG) |= ui32OscSelect;
//
// Set the M, N and Q values provided from the table and preserve
// the power state of the main PLL.
//
HWREG(SYSCTL_PLLFREQ1) =
g_pppui32XTALtoVCO[i32VCOIdx][i32XtalIdx][1];
HWREG(SYSCTL_PLLFREQ0) =
(g_pppui32XTALtoVCO[i32VCOIdx][i32XtalIdx][0] |
(HWREG(SYSCTL_PLLFREQ0) & SYSCTL_PLLFREQ0_PLLPWR));
}
//
// Calculate the System divider such that we get a frequency that is
// the closest to the requested frequency without going over.
//
ui32SysDiv = (g_pui32VCOFrequencies[i32VCOIdx] + ui32SysClock - 1) /
ui32SysClock;
//
// Calculate the actual system clock.
//
ui32SysClock = _SysCtlFrequencyGet(ui32Osc) / ui32SysDiv;
//
// Set the Flash and EEPROM timing values.
//
HWREG(SYSCTL_MEMTIM0) = _SysCtlMemTimingGet(ui32SysClock);
//
// Check if the PLL is already powered up.
//
if(HWREG(SYSCTL_PLLFREQ0) & SYSCTL_PLLFREQ0_PLLPWR)
{
if(bNewPLL == true)
{
//
// Trigger the PLL to lock to the new frequency.
//
HWREG(SYSCTL_RSCLKCFG) |= SYSCTL_RSCLKCFG_NEWFREQ;
}
}
else
{
//
// Power up the PLL.
//
HWREG(SYSCTL_PLLFREQ0) |= SYSCTL_PLLFREQ0_PLLPWR;
}
//
// Wait until the PLL has locked.
//
for(i32Timeout = 32768; i32Timeout > 0; i32Timeout--)
{
if((HWREG(SYSCTL_PLLSTAT) & SYSCTL_PLLSTAT_LOCK))
{
break;
}
}
//
// If the loop above did not timeout then switch over to the PLL
//
if(i32Timeout)
{
ui32RSClkConfig = HWREG(SYSCTL_RSCLKCFG);
ui32RSClkConfig |= ((ui32SysDiv - 1) <<
SYSCTL_RSCLKCFG_PSYSDIV_S) | ui32OscSelect |
SYSCTL_RSCLKCFG_USEPLL;
ui32RSClkConfig |= SYSCTL_RSCLKCFG_MEMTIMU;
//
// Set the new clock configuration.
//
HWREG(SYSCTL_RSCLKCFG) = ui32RSClkConfig;
}
else
{
ui32SysClock = 0;
}
}
else
{
//
// Set the Flash and EEPROM timing values for PIOSC.
//
HWREG(SYSCTL_MEMTIM0) = _SysCtlMemTimingGet(16000000);
//
// Make sure that the PLL is powered down since it is not being used.
//
HWREG(SYSCTL_PLLFREQ0) &= ~SYSCTL_PLLFREQ0_PLLPWR;
//
// Clear the old PLL divider and source in case it was set.
//
ui32RSClkConfig = HWREG(SYSCTL_RSCLKCFG);
ui32RSClkConfig &= ~(SYSCTL_RSCLKCFG_OSYSDIV_M |
SYSCTL_RSCLKCFG_OSCSRC_M |
SYSCTL_RSCLKCFG_USEPLL);
//
// Update the memory timings.
//
ui32RSClkConfig |= SYSCTL_RSCLKCFG_MEMTIMU;
//
// Set the new clock configuration.
//
HWREG(SYSCTL_RSCLKCFG) = ui32RSClkConfig;
//
// If zero given as the system clock then default to divide by 1.
//
if(ui32SysClock == 0)
{
ui32SysDiv = 0;
}
else
{
//
// Calculate the System divider based on the requested
// frequency.
//
ui32SysDiv = ui32Osc / ui32SysClock;
//
// If the system divisor is not already zero, subtract one to
// set the value in the register which requires the value to
// be n-1.
//
if(ui32SysDiv != 0)
{
ui32SysDiv -= 1;
}
//
// Calculate the system clock.
//
ui32SysClock = ui32Osc / (ui32SysDiv + 1);
}
//
// Set the memory timing values for the new system clock.
//
HWREG(SYSCTL_MEMTIM0) = _SysCtlMemTimingGet(ui32SysClock);
//
// Set the new system clock values.
//
ui32RSClkConfig = HWREG(SYSCTL_RSCLKCFG);
ui32RSClkConfig |= (ui32SysDiv << SYSCTL_RSCLKCFG_OSYSDIV_S) |
ui32OscSelect;
//
// Update the memory timings.
//
ui32RSClkConfig |= SYSCTL_RSCLKCFG_MEMTIMU;
//
// Set the new clock configuration.
//
HWREG(SYSCTL_RSCLKCFG) = ui32RSClkConfig;
}
return(ui32SysClock);
}
//*****************************************************************************
//
//! Sets the clocking of the device.
//!
//! \param ui32Config is the required configuration of the device clocking.
//!
//! This function configures the clocking of the device. The input crystal
//! frequency, oscillator to be used, use of the PLL, and the system clock
//! divider are all configured with this function.
//!
//! The \e ui32Config parameter is the logical OR of several different values,
//! many of which are grouped into sets where only one can be chosen.
//!
//! The system clock divider is chosen with one of the following values:
//! \b SYSCTL_SYSDIV_1, \b SYSCTL_SYSDIV_2, \b SYSCTL_SYSDIV_3, ...
//! \b SYSCTL_SYSDIV_64.
//!
//! The use of the PLL is chosen with either \b SYSCTL_USE_PLL or
//! \b SYSCTL_USE_OSC.
//!
//! The external crystal frequency is chosen with one of the following values:
//! \b SYSCTL_XTAL_4MHZ, \b SYSCTL_XTAL_4_09MHZ, \b SYSCTL_XTAL_4_91MHZ,
//! \b SYSCTL_XTAL_5MHZ, \b SYSCTL_XTAL_5_12MHZ, \b SYSCTL_XTAL_6MHZ,
//! \b SYSCTL_XTAL_6_14MHZ, \b SYSCTL_XTAL_7_37MHZ, \b SYSCTL_XTAL_8MHZ,
//! \b SYSCTL_XTAL_8_19MHZ, \b SYSCTL_XTAL_10MHZ, \b SYSCTL_XTAL_12MHZ,
//! \b SYSCTL_XTAL_12_2MHZ, \b SYSCTL_XTAL_13_5MHZ, \b SYSCTL_XTAL_14_3MHZ,
//! \b SYSCTL_XTAL_16MHZ, \b SYSCTL_XTAL_16_3MHZ, \b SYSCTL_XTAL_18MHZ,
//! \b SYSCTL_XTAL_20MHZ, \b SYSCTL_XTAL_24MHZ, or \b SYSCTL_XTAL_25MHz.
//! Values below \b SYSCTL_XTAL_5MHZ are not valid when the PLL is in
//! operation.
//!
//! The oscillator source is chosen with one of the following values:
//! \b SYSCTL_OSC_MAIN, \b SYSCTL_OSC_INT, \b SYSCTL_OSC_INT4,
//! \b SYSCTL_OSC_INT30, or \b SYSCTL_OSC_EXT32. \b SYSCTL_OSC_EXT32 is only
//! available on devices with the hibernate module, and then only when the
//! hibernate module has been enabled.
//!
//! The internal and main oscillators are disabled with the
//! \b SYSCTL_INT_OSC_DIS and \b SYSCTL_MAIN_OSC_DIS flags, respectively.
//! The external oscillator must be enabled in order to use an external clock
//! source. Note that attempts to disable the oscillator used to clock the
//! device is prevented by the hardware.
//!
//! To clock the system from an external source (such as an external crystal
//! oscillator), use \b SYSCTL_USE_OSC \b | \b SYSCTL_OSC_MAIN. To clock the
//! system from the main oscillator, use \b SYSCTL_USE_OSC \b |
//! \b SYSCTL_OSC_MAIN. To clock the system from the PLL, use
//! \b SYSCTL_USE_PLL \b | \b SYSCTL_OSC_MAIN, and select the appropriate
//! crystal with one of the \b SYSCTL_XTAL_xxx values.
//!
//! \note This function should only be called on TM4C123 devices. For
//! all other devices use the SysCtlClockFreqSet() function.
//!
//! \note If selecting the PLL as the system clock source (that is, via
//! \b SYSCTL_USE_PLL), this function polls the PLL lock interrupt to
//! determine when the PLL has locked. If an interrupt handler for the
//! system control interrupt is in place, and it responds to and clears the
//! PLL lock interrupt, this function delays until its timeout has occurred
//! instead of completing as soon as PLL lock is achieved.
//!
//! \return None.
//
//*****************************************************************************
void
SysCtlClockSet(uint32_t ui32Config)
{
uint32_t ui32Delay, ui32RCC, ui32RCC2;
//
// Get the current value of the RCC and RCC2 registers.
//
ui32RCC = HWREG(SYSCTL_RCC);
ui32RCC2 = HWREG(SYSCTL_RCC2);
//
// Bypass the PLL and system clock dividers for now.
//
ui32RCC |= SYSCTL_RCC_BYPASS;
ui32RCC &= ~(SYSCTL_RCC_USESYSDIV);
ui32RCC2 |= SYSCTL_RCC2_BYPASS2;
//
// Write the new RCC value.
//
HWREG(SYSCTL_RCC) = ui32RCC;
HWREG(SYSCTL_RCC2) = ui32RCC2;
//
// See if the oscillator needs to be enabled.
//
if((ui32RCC & SYSCTL_RCC_MOSCDIS) && !(ui32Config & SYSCTL_MAIN_OSC_DIS))
{
//
// Make sure that the required oscillators are enabled. For now, the
// previously enabled oscillators must be enabled along with the newly
// requested oscillators.
//
ui32RCC &= (~SYSCTL_RCC_MOSCDIS | (ui32Config & SYSCTL_MAIN_OSC_DIS));
//
// Clear the MOSC power up raw interrupt status to be sure it is not
// set when waiting below.
//
HWREG(SYSCTL_MISC) = SYSCTL_MISC_MOSCPUPMIS;
//
// Write the new RCC value.
//
HWREG(SYSCTL_RCC) = ui32RCC;
//
// Timeout using the legacy delay value.
//
ui32Delay = 524288;
while((HWREG(SYSCTL_RIS) & SYSCTL_RIS_MOSCPUPRIS) == 0)
{
ui32Delay--;
if(ui32Delay == 0)
{
break;
}
}
//
// If the main oscillator failed to start up then do not switch to
// it and return.
//
if(ui32Delay == 0)
{
return;
}
}
//
// Set the new crystal value and oscillator source. Because the OSCSRC2
// field in RCC2 overlaps the XTAL field in RCC, the OSCSRC field has a
// special encoding within ui32Config to avoid the overlap.
//
ui32RCC &= ~(SYSCTL_RCC_XTAL_M | SYSCTL_RCC_OSCSRC_M);
ui32RCC |= ui32Config & (SYSCTL_RCC_XTAL_M | SYSCTL_RCC_OSCSRC_M);
ui32RCC2 &= ~(SYSCTL_RCC2_USERCC2 | SYSCTL_RCC2_OSCSRC2_M);
ui32RCC2 |= ui32Config & (SYSCTL_RCC2_USERCC2 | SYSCTL_RCC_OSCSRC_M);
ui32RCC2 |= (ui32Config & 0x00000008) << 3;
//
// Write the new RCC value.
//
HWREG(SYSCTL_RCC) = ui32RCC;
HWREG(SYSCTL_RCC2) = ui32RCC2;
//
// Set the PLL configuration.
//
ui32RCC &= ~SYSCTL_RCC_PWRDN;
ui32RCC |= ui32Config & SYSCTL_RCC_PWRDN;
ui32RCC2 &= ~SYSCTL_RCC2_PWRDN2;
ui32RCC2 |= ui32Config & SYSCTL_RCC2_PWRDN2;
//
// Clear the PLL lock interrupt.
//
HWREG(SYSCTL_MISC) = SYSCTL_MISC_PLLLMIS;
//
// Write the new RCC value.
//
if(ui32RCC2 & SYSCTL_RCC2_USERCC2)
{
HWREG(SYSCTL_RCC2) = ui32RCC2;
HWREG(SYSCTL_RCC) = ui32RCC;
}
else
{
HWREG(SYSCTL_RCC) = ui32RCC;
HWREG(SYSCTL_RCC2) = ui32RCC2;
}
//
// Set the requested system divider and disable the appropriate
// oscillators. This value is not written immediately.
//
ui32RCC &= ~(SYSCTL_RCC_SYSDIV_M | SYSCTL_RCC_USESYSDIV |
SYSCTL_RCC_MOSCDIS);
ui32RCC |= ui32Config & (SYSCTL_RCC_SYSDIV_M | SYSCTL_RCC_USESYSDIV |
SYSCTL_RCC_MOSCDIS);
ui32RCC2 &= ~(SYSCTL_RCC2_SYSDIV2_M);
ui32RCC2 |= ui32Config & SYSCTL_RCC2_SYSDIV2_M;
if(ui32Config & SYSCTL_RCC2_DIV400)
{
ui32RCC |= SYSCTL_RCC_USESYSDIV;
ui32RCC2 &= ~(SYSCTL_RCC_USESYSDIV);
ui32RCC2 |= ui32Config & (SYSCTL_RCC2_DIV400 | SYSCTL_RCC2_SYSDIV2LSB);
}
else
{
ui32RCC2 &= ~(SYSCTL_RCC2_DIV400);
}
//
// See if the PLL output is being used to clock the system.
//
if(!(ui32Config & SYSCTL_RCC_BYPASS))
{
//
// Wait until the PLL has locked.
//
for(ui32Delay = 32768; ui32Delay > 0; ui32Delay--)
{
if((HWREG(SYSCTL_PLLSTAT) & SYSCTL_PLLSTAT_LOCK))
{
break;
}
}
//
// Enable use of the PLL.
//
ui32RCC &= ~(SYSCTL_RCC_BYPASS);
ui32RCC2 &= ~(SYSCTL_RCC2_BYPASS2);
}
//
// Write the final RCC value.
//
HWREG(SYSCTL_RCC) = ui32RCC;
HWREG(SYSCTL_RCC2) = ui32RCC2;
//
// Delay for a little bit so that the system divider takes effect.
//
SysCtlDelay(16);
}
//*****************************************************************************
//
//! Gets the processor clock rate.
//!
//! This function determines the clock rate of the processor clock, which is
//! also the clock rate of the peripheral modules (with the exception of
//! PWM, which has its own clock divider; other peripherals may have different
//! clocking, see the device data sheet for details).
//!
//! \note This cannot return accurate results if SysCtlClockSet() has not
//! been called to configure the clocking of the device, or if the device is
//! directly clocked from a crystal (or a clock source) that is not one of the
//! supported crystal frequencies. In the latter case, this function should be
//! modified to directly return the correct system clock rate.
//!
//! \note This function can only be called on TM4C123 devices. For TM4C129
//! devices, the return value from SysCtlClockFreqSet() indicates the system
//! clock frequency.
//!
//! \return The processor clock rate for TM4C123 devices only.
//
//*****************************************************************************
uint32_t
SysCtlClockGet(void)
{
uint32_t ui32RCC, ui32RCC2, ui32PLL, ui32Clk, ui32Max;
uint32_t ui32PLL1;
//
// This function is only valid on TM4C123 devices.
//
ASSERT(CLASS_IS_TM4C123);
//
// Read RCC and RCC2.
//
ui32RCC = HWREG(SYSCTL_RCC);
ui32RCC2 = HWREG(SYSCTL_RCC2);
//
// Get the base clock rate.
//
switch((ui32RCC2 & SYSCTL_RCC2_USERCC2) ?
(ui32RCC2 & SYSCTL_RCC2_OSCSRC2_M) :
(ui32RCC & SYSCTL_RCC_OSCSRC_M))
{
//
// The main oscillator is the clock source. Determine its rate from
// the crystal setting field.
//
case SYSCTL_RCC_OSCSRC_MAIN:
{
ui32Clk = g_pui32Xtals[(ui32RCC & SYSCTL_RCC_XTAL_M) >>
SYSCTL_RCC_XTAL_S];
break;
}
//
// The internal oscillator is the source clock.
//
case SYSCTL_RCC_OSCSRC_INT:
{
//
// The internal oscillator on all devices is 16 MHz.
//
ui32Clk = 16000000;
break;
}
//
// The internal oscillator divided by four is the source clock.
//
case SYSCTL_RCC_OSCSRC_INT4:
{
//
// The internal oscillator on all devices is 16 MHz.
//
ui32Clk = 16000000 / 4;
break;
}
//
// The internal 30-KHz oscillator is the source clock.
//
case SYSCTL_RCC_OSCSRC_30:
{
//
// The internal 30-KHz oscillator has an accuracy of +/- 30%.
//
ui32Clk = 30000;
break;
}
//
// The 32.768-KHz clock from the hibernate module is the source clock.
//
case SYSCTL_RCC2_OSCSRC2_32:
{
ui32Clk = 32768;
break;
}
//
// An unknown setting, so return a zero clock (that is, an unknown
// clock rate).
//
default:
{
return(0);
}
}
//
// Default the maximum frequency to the maximum 32-bit unsigned value.
//
ui32Max = 0xffffffff;
//
// See if the PLL is being used.
//
if(((ui32RCC2 & SYSCTL_RCC2_USERCC2) &&
!(ui32RCC2 & SYSCTL_RCC2_BYPASS2)) ||
(!(ui32RCC2 & SYSCTL_RCC2_USERCC2) && !(ui32RCC & SYSCTL_RCC_BYPASS)))
{
//
// Read the two PLL frequency registers. The formula for a
// TM4C123 device is "(xtal * m) / ((q + 1) * (n + 1))".
//
ui32PLL = HWREG(SYSCTL_PLLFREQ0);
ui32PLL1 = HWREG(SYSCTL_PLLFREQ1);
//
// Divide the input clock by the dividers.
//
ui32Clk /= ((((ui32PLL1 & SYSCTL_PLLFREQ1_Q_M) >>
SYSCTL_PLLFREQ1_Q_S) + 1) *
(((ui32PLL1 & SYSCTL_PLLFREQ1_N_M) >>
SYSCTL_PLLFREQ1_N_S) + 1) * 2);
//
// Multiply the clock by the multiplier, which is split into an
// integer part and a fractional part.
//
ui32Clk = ((ui32Clk * ((ui32PLL & SYSCTL_PLLFREQ0_MINT_M) >>
SYSCTL_PLLFREQ0_MINT_S)) +
((ui32Clk * ((ui32PLL & SYSCTL_PLLFREQ0_MFRAC_M) >>
SYSCTL_PLLFREQ0_MFRAC_S)) >> 10));
//
// Force the system divider to be enabled. It is always used when
// using the PLL, but in some cases it does not read as being enabled.
//
ui32RCC |= SYSCTL_RCC_USESYSDIV;
//
// Calculate the maximum system frequency.
//
switch(HWREG(SYSCTL_DC1) & SYSCTL_DC1_MINSYSDIV_M)
{
case SYSCTL_DC1_MINSYSDIV_80:
{
ui32Max = 80000000;
break;
}
case SYSCTL_DC1_MINSYSDIV_66:
{
ui32Max = 66666666;
break;
}
case SYSCTL_DC1_MINSYSDIV_50:
{
ui32Max = 50000000;
break;
}
case SYSCTL_DC1_MINSYSDIV_40:
{
ui32Max = 40000000;
break;
}
case SYSCTL_DC1_MINSYSDIV_25:
{
ui32Max = 25000000;
break;
}
case SYSCTL_DC1_MINSYSDIV_20:
{
ui32Max = 20000000;
break;
}
default:
{
break;
}
}
}
//
// See if the system divider is being used.
//
if(ui32RCC & SYSCTL_RCC_USESYSDIV)
{
//
// Adjust the clock rate by the system clock divider.
//
if(ui32RCC2 & SYSCTL_RCC2_USERCC2)
{
if((ui32RCC2 & SYSCTL_RCC2_DIV400) &&
(((ui32RCC2 & SYSCTL_RCC2_USERCC2) &&
!(ui32RCC2 & SYSCTL_RCC2_BYPASS2)) ||
(!(ui32RCC2 & SYSCTL_RCC2_USERCC2) &&
!(ui32RCC & SYSCTL_RCC_BYPASS))))
{
ui32Clk = ((ui32Clk * 2) / (((ui32RCC2 &
(SYSCTL_RCC2_SYSDIV2_M |
SYSCTL_RCC2_SYSDIV2LSB)) >>
(SYSCTL_RCC2_SYSDIV2_S - 1)) +
1));
}
else
{
ui32Clk /= (((ui32RCC2 & SYSCTL_RCC2_SYSDIV2_M) >>
SYSCTL_RCC2_SYSDIV2_S) + 1);
}
}
else
{
ui32Clk /= (((ui32RCC & SYSCTL_RCC_SYSDIV_M) >>
SYSCTL_RCC_SYSDIV_S) + 1);
}
}
//
// Limit the maximum clock to the maximum clock frequency.
//
if(ui32Max < ui32Clk)
{
ui32Clk = ui32Max;
}
//
// Return the computed clock rate.
//
return(ui32Clk);
}
//*****************************************************************************
//
//! Sets the clocking of the device while in deep-sleep mode.
//!
//! \param ui32Config is the required configuration of the device clocking
//! while in deep-sleep mode.
//!
//! This function configures the clocking of the device while in deep-sleep
//! mode. The oscillator to be used and the system clock divider are
//! configured with this function.
//!
//! The \e ui32Config parameter is the logical OR of the following values:
//!
//! The system clock divider is chosen from one of the following values:
//! \b SYSCTL_DSLP_DIV_1, \b SYSCTL_DSLP_DIV_2, \b SYSCTL_DSLP_DIV_3, ...
//! \b SYSCTL_DSLP_DIV_64.
//!
//! The oscillator source is chosen from one of the following values:
//! \b SYSCTL_DSLP_OSC_MAIN, \b SYSCTL_DSLP_OSC_INT, \b SYSCTL_DSLP_OSC_INT30,
//! or \b SYSCTL_DSLP_OSC_EXT32. \b SYSCTL_OSC_EXT32 is only available on
//! devices with the hibernation module, and then only when the hibernation
//! module has been enabled.
//!
//! The precision internal oscillator can be powered down in deep-sleep mode by
//! specifying \b SYSCTL_DSLP_PIOSC_PD. The precision internal oscillator is
//! not powered down if it is required for operation while in deep-sleep
//! (based on other configuration settings.)
//!
//! \note This function should only be called on TM4C123 devices. For
//! other devices use the SysCtlDeepSleepClockConfigSet() function.
//!
//! \note The availability of deep-sleep clocking configuration varies with the
//! Tiva part in use. Please consult the data sheet for the part you are
//! using to determine whether this support is available.
//!
//! \return None.
//
//*****************************************************************************
void
SysCtlDeepSleepClockSet(uint32_t ui32Config)
{
//
// Set the deep-sleep clock configuration.
//
HWREG(SYSCTL_DSLPCLKCFG) = ui32Config;
}
//*****************************************************************************
//
//! Sets the clock configuration of the device while in deep-sleep mode.
//!
//! \param ui32Div is the clock divider when in deep-sleep mode.
//! \param ui32Config is the configuration of the device clocking while
//! in deep-sleep mode.
//!
//! This function configures the clocking of the device while in deep-sleep
//! mode. The \e ui32Config parameter selects the oscillator and the
//! \e ui32Div parameter sets the clock divider used in deep-sleep mode. The
//! valid values for the \e ui32Div parameter range from 1 to 1024, however not
//! all Tiva microcontrollers support this full range. This function
//! replaces the SysCtlDeepSleepClockSet() function and can be used on
//! Tiva devices that support deep-sleep mode.
//!
//! The oscillator source is chosen from one of the following values:
//! \b SYSCTL_DSLP_OSC_MAIN, \b SYSCTL_DSLP_OSC_INT, \b SYSCTL_DSLP_OSC_INT30,
//! or \b SYSCTL_DSLP_OSC_EXT32. The \b SYSCTL_DSLP_OSC_EXT32 option is only
//! available on devices with the hibernation module, and then only when the
//! hibernation module is enabled.
//!
//! The precision internal oscillator can be powered down in deep-sleep mode by
//! specifying \b SYSCTL_DSLP_PIOSC_PD. The precision internal oscillator is
//! not powered down if it is required for operation while in deep-sleep
//! (based on other configuration settings).
//!
//! The main oscillator can be powered down in deep-sleep mode by
//! specifying \b SYSCTL_DSLP_MOSC_PD. The main oscillator is
//! not powered down if it is required for operation while in deep-sleep
//! (based on other configuration settings).
//!
//! \note The availability of deep-sleep clocking configuration and the
//! configuration values vary with the Tiva device in use. Please consult
//! the data sheet for the device you are using to determine whether the
//! desired configuration options are available and to determine the valid
//! range for the clock divider.
//!
//! \return None.
//
//*****************************************************************************
void
SysCtlDeepSleepClockConfigSet(uint32_t ui32Div, uint32_t ui32Config)
{
uint32_t ui32Value;
ASSERT(ui32Div != 0);
if(CLASS_IS_TM4C123)
{
//
// Set the deep-sleep clock configuration.
//
HWREG(SYSCTL_DSLPCLKCFG) = (ui32Config & ~SYSCTL_DSLPCLKCFG_D_M) |
((ui32Div - 1) << SYSCTL_DSLPCLKCFG_D_S);
}
else
{
//
// Initialize the value with the divider.
//
ui32Value = ui32Div - 1;
//
// Set the clock source selection based on the defines used for
// SysCtlDeepSleepClockSet() function so that there is some backwards
// compatibility.
//
switch(ui32Config & SYSCTL_DSLPCLKCFG_O_M)
{
//
// Choose the main external oscillator.
//
case SYSCTL_DSLP_OSC_MAIN:
{
ui32Value |= SYSCTL_DSCLKCFG_DSOSCSRC_MOSC;
break;
}
//
// Choose the low frequency oscillator.
//
case SYSCTL_DSLP_OSC_INT30:
{
ui32Value |= SYSCTL_DSCLKCFG_DSOSCSRC_LFIOSC;
break;
}
//
// Choose the low frequency oscillator.
//
case SYSCTL_DSLP_OSC_EXT32:
{
ui32Value |= SYSCTL_DSCLKCFG_DSOSCSRC_RTC;
break;
}
//
// The zero value uses the PIOSC as the clock source.
//
case SYSCTL_DSLP_OSC_INT:
default:
{
break;
}
}
//
// Set the PIOSC power down bit.
//
if(ui32Config & SYSCTL_DSLP_PIOSC_PD)
{
ui32Value |= SYSCTL_DSCLKCFG_PIOSCPD;
}
//
// Set the PIOSC power down bit.
//
if(ui32Config & SYSCTL_DSLP_MOSC_PD)
{
ui32Value |= SYSCTL_DSCLKCFG_MOSCDPD;
}
//
// Update the deep-sleep clock configuration.
//
HWREG(SYSCTL_DSCLKCFG) = ui32Value;
}
}
//*****************************************************************************
//
//! Sets the PWM clock configuration.
//!
//! \param ui32Config is the configuration for the PWM clock; it must be one of
//! \b SYSCTL_PWMDIV_1, \b SYSCTL_PWMDIV_2, \b SYSCTL_PWMDIV_4,
//! \b SYSCTL_PWMDIV_8, \b SYSCTL_PWMDIV_16, \b SYSCTL_PWMDIV_32, or
//! \b SYSCTL_PWMDIV_64.
//!
//! This function configures the rate of the clock provided to the PWM module
//! as a ratio of the processor clock. This clock is used by the PWM module to
//! generate PWM signals; its rate forms the basis for all PWM signals.
//!
//! \note This function should only be used with TM4C123 devices. For
//! other TM4C devices, the PWMClockSet() function should be used.
//!
//! \note The clocking of the PWM is dependent on the system clock rate as
//! configured by SysCtlClockSet().
//!
//! \return None.
//
//*****************************************************************************
void
SysCtlPWMClockSet(uint32_t ui32Config)
{
//
// Check the arguments.
//
ASSERT((ui32Config == SYSCTL_PWMDIV_1) ||
(ui32Config == SYSCTL_PWMDIV_2) ||
(ui32Config == SYSCTL_PWMDIV_4) ||
(ui32Config == SYSCTL_PWMDIV_8) ||
(ui32Config == SYSCTL_PWMDIV_16) ||
(ui32Config == SYSCTL_PWMDIV_32) ||
(ui32Config == SYSCTL_PWMDIV_64));
//
// Check that there is a PWM block on this part.
//
ASSERT(HWREG(SYSCTL_DC1) & (SYSCTL_DC1_PWM0 | SYSCTL_DC1_PWM1));
//
// Set the PWM clock configuration into the run-mode clock configuration
// register.
//
HWREG(SYSCTL_RCC) = ((HWREG(SYSCTL_RCC) &
~(SYSCTL_RCC_USEPWMDIV | SYSCTL_RCC_PWMDIV_M)) |
ui32Config);
}
//*****************************************************************************
//
//! Gets the current PWM clock configuration.
//!
//! This function returns the current PWM clock configuration.
//!
//! \return Returns the current PWM clock configuration; is one of
//! \b SYSCTL_PWMDIV_1, \b SYSCTL_PWMDIV_2, \b SYSCTL_PWMDIV_4,
//! \b SYSCTL_PWMDIV_8, \b SYSCTL_PWMDIV_16, \b SYSCTL_PWMDIV_32, or
//! \b SYSCTL_PWMDIV_64.
//!
//! \note This function should only be used with TM4C123 devices. For
//! other TM4C devices, the PWMClockGet() function should be used.
//
//*****************************************************************************
uint32_t
SysCtlPWMClockGet(void)
{
//
// Check that there is a PWM block on this part.
//
ASSERT(HWREG(SYSCTL_DC1) & (SYSCTL_DC1_PWM0 | SYSCTL_DC1_PWM1));
//
// Return the current PWM clock configuration. Make sure that
// SYSCTL_PWMDIV_1 is returned in all cases where the divider is disabled.
//
if(!(HWREG(SYSCTL_RCC) & SYSCTL_RCC_USEPWMDIV))
{
//
// The divider is not active so reflect this in the value we return.
//
return(SYSCTL_PWMDIV_1);
}
else
{
//
// The divider is active so directly return the masked register value.
//
return(HWREG(SYSCTL_RCC) &
(SYSCTL_RCC_USEPWMDIV | SYSCTL_RCC_PWMDIV_M));
}
}
//*****************************************************************************
//
//! Enables access to a GPIO peripheral via the AHB.
//!
//! \param ui32GPIOPeripheral is the GPIO peripheral to enable.
//!
//! This function is used to enable the specified GPIO peripheral to be
//! accessed from the Advanced Host Bus (AHB) instead of the legacy Advanced
//! Peripheral Bus (APB). When a GPIO peripheral is enabled for AHB access,
//! the \b _AHB_BASE form of the base address should be used for GPIO
//! functions. For example, instead of using \b GPIO_PORTA_BASE as the base
//! address for GPIO functions, use \b GPIO_PORTA_AHB_BASE instead.
//!
//! The \e ui32GPIOPeripheral argument must be only one of the following
//! values:
//! \b SYSCTL_PERIPH_GPIOA, \b SYSCTL_PERIPH_GPIOB, \b SYSCTL_PERIPH_GPIOC,
//! \b SYSCTL_PERIPH_GPIOD, \b SYSCTL_PERIPH_GPIOE, \b SYSCTL_PERIPH_GPIOF,
//! \b SYSCTL_PERIPH_GPIOG, \b SYSCTL_PERIPH_GPIOH, or \b SYSCTL_PERIPH_GPIOJ.
//!
//! \note On some devices, all GPIO ports are only available on AHB.
//!
//! \return None.
//
//*****************************************************************************
void
SysCtlGPIOAHBEnable(uint32_t ui32GPIOPeripheral)
{
//
// Check the arguments.
//
ASSERT((ui32GPIOPeripheral == SYSCTL_PERIPH_GPIOA) ||
(ui32GPIOPeripheral == SYSCTL_PERIPH_GPIOB) ||
(ui32GPIOPeripheral == SYSCTL_PERIPH_GPIOC) ||
(ui32GPIOPeripheral == SYSCTL_PERIPH_GPIOD) ||
(ui32GPIOPeripheral == SYSCTL_PERIPH_GPIOE) ||
(ui32GPIOPeripheral == SYSCTL_PERIPH_GPIOF) ||
(ui32GPIOPeripheral == SYSCTL_PERIPH_GPIOG) ||
(ui32GPIOPeripheral == SYSCTL_PERIPH_GPIOH) ||
(ui32GPIOPeripheral == SYSCTL_PERIPH_GPIOJ));
//
// Enable this GPIO for AHB access.
//
HWREG(SYSCTL_GPIOHBCTL) |= (1 << (ui32GPIOPeripheral & 0xF));
}
//*****************************************************************************
//
//! Disables access to a GPIO peripheral via the AHB.
//!
//! \param ui32GPIOPeripheral is the GPIO peripheral to disable.
//!
//! This function disables the specified GPIO peripheral for access from the
//! Advanced Host Bus (AHB). Once disabled, the GPIO peripheral is accessed
//! from the legacy Advanced Peripheral Bus (APB).
//!
//! The \b ui32GPIOPeripheral argument must be only one of the following
//! values:
//! \b SYSCTL_PERIPH_GPIOA, \b SYSCTL_PERIPH_GPIOB, \b SYSCTL_PERIPH_GPIOC,
//! \b SYSCTL_PERIPH_GPIOD, \b SYSCTL_PERIPH_GPIOE, \b SYSCTL_PERIPH_GPIOF,
//! \b SYSCTL_PERIPH_GPIOG, \b SYSCTL_PERIPH_GPIOH, or \b SYSCTL_PERIPH_GPIOJ.
//!
//! \note Some devices allow disabling AHB access to GPIO ports that are only
//! present on the AHB. Disabling AHB access to these ports will disable
//! access to these GPIO ports. On some devices, all GPIO ports are only
//! available on AHB.
//!
//! \return None.
//
//*****************************************************************************
void
SysCtlGPIOAHBDisable(uint32_t ui32GPIOPeripheral)
{
//
// Check the arguments.
//
ASSERT((ui32GPIOPeripheral == SYSCTL_PERIPH_GPIOA) ||
(ui32GPIOPeripheral == SYSCTL_PERIPH_GPIOB) ||
(ui32GPIOPeripheral == SYSCTL_PERIPH_GPIOC) ||
(ui32GPIOPeripheral == SYSCTL_PERIPH_GPIOD) ||
(ui32GPIOPeripheral == SYSCTL_PERIPH_GPIOE) ||
(ui32GPIOPeripheral == SYSCTL_PERIPH_GPIOF) ||
(ui32GPIOPeripheral == SYSCTL_PERIPH_GPIOG) ||
(ui32GPIOPeripheral == SYSCTL_PERIPH_GPIOH) ||
(ui32GPIOPeripheral == SYSCTL_PERIPH_GPIOJ));
//
// Disable this GPIO for AHB access.
//
HWREG(SYSCTL_GPIOHBCTL) &= ~(1 << (ui32GPIOPeripheral & 0xF));
}
//*****************************************************************************
//
//! Powers up the USB PLL.
//!
//! This function enables the USB controller's PLL, which is used by its
//! physical layer. This call is necessary before connecting to any external
//! devices.
//!
//! \note This function should only be called on TM4C123 devices.
//!
//! \return None.
//
//*****************************************************************************
void
SysCtlUSBPLLEnable(void)
{
//
// Turn on the USB PLL.
//
HWREG(SYSCTL_RCC2) &= ~SYSCTL_RCC2_USBPWRDN;
}
//*****************************************************************************
//
//! Powers down the USB PLL.
//!
//! This function disables the USB controller's PLL, which is used by its
//! physical layer. The USB registers are still accessible, but the physical
//! layer no longer functions.
//!
//! \note This function should only be called on TM4C123 devices.
//!
//! \return None.
//
//*****************************************************************************
void
SysCtlUSBPLLDisable(void)
{
//
// Turn off the USB PLL.
//
HWREG(SYSCTL_RCC2) |= SYSCTL_RCC2_USBPWRDN;
}
//*****************************************************************************
//
//! Configures the response to system voltage events.
//!
//! \param ui32Config holds the configuration options for the voltage events.
//!
//! This function configures the response to voltage-related events.
//! These events are triggered when the voltage rails drop below certain
//! levels. The \e ui32Config parameter provides the configuration for the
//! voltage events and is a combination of the \b SYSCTL_VEVENT_* values.
//!
//! The response to a brown out on the VDDA rail is set by using one of the
//! following values:
//! - \b SYSCTL_VEVENT_VDDABO_NONE - There is no action taken on a VDDA
//! brown out.
//! - \b SYSCTL_VEVENT_VDDABO_INT - A system interrupt is generated when a
//! VDDA brown out occurs.
//! - \b SYSCTL_VEVENT_VDDABO_NMI - An NMI is generated when a VDDA brown out
//! occurs.
//! - \b SYSCTL_VEVENT_VDDABO_RST - A reset is generated when a VDDA brown out
//! occurs. The type of reset that is generated is controller by the
//! \b SYSCTL_ONRST_BOR_* setting passed into the SysCtlResetBehaviorSet()
//! function.
//!
//! The response to a brown out on the VDD rail is set by using one of the
//! following values:
//! - \b SYSCTL_VEVENT_VDDBO_NONE - There is no action taken on a VDD
//! brown out.
//! - \b SYSCTL_VEVENT_VDDBO_INT - A system interrupt is generated when a
//! VDD brown out occurs.
//! - \b SYSCTL_VEVENT_VDDBO_NMI - An NMI is generated when a VDD brown out
//! occurs.
//! - \b SYSCTL_VEVENT_VDDBO_RST - A reset is generated when a VDD brown out
//! occurs. The type of reset that is generated is controller by the
//! \b SYSCTL_ONRST_BOR_* setting passed into the SysCtlResetBehaviorSet()
//! function.
//!
//! \b Example: Configure the voltage events to trigger an interrupt on a VDDA
//! brown out, an NMI on a VDDC brown out and a reset on a VDD brown out.
//!
//! \verbatim
//!
//! //
//! // Configure the BOR rest to trigger a full POR. This is needed because
//! // the SysCtlVoltageEventConfig() call is triggering a reset so the type
//! // of reset is specified by this call.
//! //
//! SysCtlResetBehaviorSet(SYSCTL_ONRST_BOR_POR);
//!
//! //
//! // Trigger an interrupt on a VDDA brown out and a reset on a VDD brown out.
//! //
//! SysCtlVoltageEventConfig(SYSCTL_VEVENT_VDDABO_INT |
//! SYSCTL_VEVENT_VDDBO_RST);
//! \endverbatim
//!
//! \return None.
//
//*****************************************************************************
void
SysCtlVoltageEventConfig(uint32_t ui32Config)
{
//
// Set the requested events.
//
HWREG(SYSCTL_PTBOCTL) = ui32Config;
}
//*****************************************************************************
//
//! Returns the voltage event status.
//!
//! This function returns the voltage event status for the system controller.
//! The value returned is a logical OR of the following values:
//! - \b SYSCTL_VESTAT_VDDBOR a brown-out event occurred on the VDD rail.
//! - \b SYSCTL_VESTAT_VDDABOR a brown-out event occurred on the VDDA rail.
//!
//! The values returned from this function can be passed to the
//! SysCtlVoltageEventClear() to clear the current voltage event status.
//! Because voltage events are not cleared due to a reset, the voltage event
//! status must be cleared by calling SysCtlVoltageEventClear().
//!
//! \b Example: Clear the current voltage event status.
//!
//! \verbatim
//! uint32_t ui32VoltageEvents;
//!
//! //
//! // Read the current voltage event status.
//! //
//! ui32VoltageEvents = SysCtlVoltageEventStatus();
//!
//! //
//! // Clear all the current voltage events.
//! //
//! SysCtlVoltageEventClear(ui32VoltageEvents);
//! \endverbatim
//!
//! \return The current voltage event status.
//!
//! \note The availability of voltage events varies with the Tiva part
//! in use. Please consult the data sheet for the part you are using to
//! determine which interrupt sources are available.
//
//*****************************************************************************
uint32_t
SysCtlVoltageEventStatus(void)
{
//
// Return the current voltage event status.
//
return(HWREG(SYSCTL_PWRTC));
}
//*****************************************************************************
//
//! Clears the voltage event status.
//!
//! \param ui32Status is a bit mask of the voltage events to clear.
//!
//! This function clears the current voltage events status for the values
//! specified in the \e ui32Status parameter. The \e ui32Status value must be
//! a logical OR of the following values:
//! - \b SYSCTL_VESTAT_VDDBOR a brown-out event occurred on the VDD rail.
//! - \b SYSCTL_VESTAT_VDDABOR a brown-out event occurred on the VDDA rail.
//!
//! \b Example: Clear the current voltage event status.
//!
//! \verbatim
//! //
//! // Clear all the current voltage events.
//! //
//! SysCtlVoltageEventClear(SysCtlVoltageEventStatus());
//! \endverbatim
//!
//! \note The availability of voltage event status varies with the
//! Tiva part in use. Please consult the data sheet for the part you are
//! using to determine which interrupt sources are available.
//!
//! \return None.
//
//*****************************************************************************
void
SysCtlVoltageEventClear(uint32_t ui32Status)
{
//
// Clear the requested voltage events.
//
HWREG(SYSCTL_PWRTC) |= ui32Status;
}
//*****************************************************************************
//
//! Returns the current NMI status.
//!
//! This function returns the NMI status for the system controller. The valid
//! values for the \e ui32Ints parameter are a logical OR of the following
//! values:
//! - \b SYSCTL_NMI_MOSCFAIL the main oscillator is not present or did not
//! start.
//! - \b SYSCTL_NMI_TAMPER a tamper event has been detected.
//! - \b SYSCTL_NMI_WDT0 watchdog 0 generated a timeout.
//! - \b SYSCTL_NMI_WDT1 watchdog 1 generated a timeout.
//! - \b SYSCTL_NMI_POWER a power event occurred.
//! - \b SYSCTL_NMI_EXTERNAL an external NMI pin asserted.
//!
//! \b Example: Clear all current NMI status flags.
//!
//! \verbatim
//!
//! //
//! // Clear all the current NMI sources.
//! //
//! SysCtlNMIClear(SysCtlNMIStatus());
//! \endverbatim
//!
//! \note The availability of the NMI status varies with the Tiva part in
//! use. Please consult the data sheet for the part you are using to determine
//! which interrupt sources are available.
//!
//! \return The current NMI status.
//
//*****************************************************************************
uint32_t
SysCtlNMIStatus(void)
{
return(HWREG(SYSCTL_NMIC));
}
//*****************************************************************************
//
//! Clears NMI sources.
//!
//! \param ui32Ints is a bit mask of the non-maskable interrupt sources.
//!
//! This function clears the current NMI status specified in the \e ui32Ints
//! parameter. The valid values for the \e ui32Ints parameter are a logical OR
//! of the following values:
//! - \b SYSCTL_NMI_MOSCFAIL the main oscillator is not present or did not
//! start.
//! - \b SYSCTL_NMI_TAMPER a tamper event has been detected.
//! - \b SYSCTL_NMI_WDT0 watchdog 0 generated a timeout.
//! - \b SYSCTL_NMI_WDT1 watchdog 1 generated a timeout.
//! - \b SYSCTL_NMI_POWER a power event occurred.
//! - \b SYSCTL_NMI_EXTERNAL an external NMI pin asserted.
//!
//! \b Example: Clear all current NMI status flags.
//!
//! \verbatim
//!
//! //
//! // Clear all the current NMI sources.
//! //
//! SysCtlNMIClear(SysCtlNMIStatus());
//! \endverbatim
//!
//! \note The availability of the NMI status varies with the Tiva part in
//! use. Please consult the data sheet for the part you are using to determine
//! which interrupt sources are available.
//!
//! \return None.
//
//*****************************************************************************
void
SysCtlNMIClear(uint32_t ui32Ints)
{
//
// Clear the requested interrupt sources.
//
HWREG(SYSCTL_NMIC) &= ~ui32Ints;
}
//*****************************************************************************
//
//! Configures and enables or disables the clock output on the DIVSCLK pin.
//!
//! \param ui32Config holds the configuration options including enabling or
//! disabling the clock output on the DIVSCLK pin.
//! \param ui32Div is the divisor for the clock selected in the \e ui32Config
//! parameter.
//!
//! This function selects the source for the DIVSCLK, enables or disables
//! the clock output and provides an output divider value. The \e ui32Div
//! parameter specifies the divider for the selected clock source and has a
//! valid range of 1-256. The \e ui32Config parameter configures
//! the DIVSCLK output based on the following settings:
//!
//! The first setting allows the output to be enabled or disabled.
//! - \b SYSCTL_CLKOUT_EN - enable the DIVSCLK output.
//! - \b SYSCTL_CLKOUT_DIS - disable the DIVSCLK output (default).
//!
//! The next group of settings selects the source for the DIVSCLK.
//! - \b SYSCTL_CLKOUT_SYSCLK - use the current system clock as the
//! source (default).
//! - \b SYSCTL_CLKOUT_PIOSC - use the PIOSC as the source.
//! - \b SYSCTL_CLKOUT_MOSC - use the MOSC as the source.
//!
//! \b Example: Enable the PIOSC divided by 4 as the DIVSCLK output.
//!
//! \verbatim
//!
//! //
//! // Enable the PIOSC divided by 4 as the DIVSCLK output.
//! //
//! SysCtlClockOutConfig(SYSCTL_DIVSCLK_EN | SYSCTL_DIVSCLK_SRC_PIOSC, 4);
//! \endverbatim
//!
//! \note The availability of the DIVSCLK output varies with the Tiva part
//! in use. Please consult the data sheet for the part you are using to
//! determine which interrupt sources are available.
//!
//! \return None.
//
//*****************************************************************************
void
SysCtlClockOutConfig(uint32_t ui32Config, uint32_t ui32Div)
{
ASSERT(ui32Div != 0);
ASSERT((ui32Config & ~(SYSCTL_CLKOUT_EN | SYSCTL_CLKOUT_DIS |
SYSCTL_CLKOUT_SYSCLK | SYSCTL_CLKOUT_PIOSC |
SYSCTL_CLKOUT_MOSC)) == 0);
//
// Set the requested configuration and divisor.
//
HWREG(SYSCTL_DIVSCLK) = ui32Config | ((ui32Div - 1) &
SYSCTL_DIVSCLK_DIV_M);
}
//*****************************************************************************
//
//! Configures the alternate peripheral clock source.
//!
//! \param ui32Config holds the configuration options for the alternate
//! peripheral clock.
//!
//! This function configures the alternate peripheral clock. The alternate
//! peripheral clock is used to provide a known clock in all operating modes
//! to peripherals that support using the alternate peripheral clock as an
//! input clock. The \e ui32Config parameter value provides the clock input
//! source using one of the following values:
//! - \b SYSCTL_ALTCLK_PIOSC - use the PIOSC as the alternate clock
//! source (default).
//! - \b SYSCTL_ALTCLK_RTCOSC - use the Hibernate module RTC clock as the
//! alternate clock source.
//! - \b SYSCTL_ALTCLK_LFIOSC - use the low-frequency internal oscillator as
//! the alternate clock source.
//!
//! \b Example: Select the Hibernate module RTC clock as the alternate clock
//! source.
//!
//! \verbatim
//!
//! //
//! // Select the Hibernate module RTC clock as the alternate clock source.
//! //
//! SysCtlAltClkConfig(SYSCTL_ALTCLK_RTCOSC);
//! \endverbatim
//!
//! \note The availability of the alternate peripheral clock varies with the
//! Tiva part in use. Please consult the data sheet for the part you are
//! using to determine which interrupt sources are available.
//!
//! \return None.
//
//*****************************************************************************
void
SysCtlAltClkConfig(uint32_t ui32Config)
{
//
// Set the requested configuration and divisor.
//
HWREG(SYSCTL_ALTCLKCFG) = ui32Config;
}
//*****************************************************************************
//
// Close the Doxygen group.
//! @}
//
//*****************************************************************************