rt-thread-official/bsp/stm32/stm32f072-st-nucleo/board/Kconfig

176 lines
4.9 KiB
Plaintext
Raw Normal View History

2019-05-30 18:00:03 +08:00
menu "Hardware Drivers Config"
menu "Onboard Peripheral Drivers"
config BSP_USING_STLINK_TO_USART
bool "Enable STLINK TO USART (uart2)"
select BSP_USING_UART
select BSP_USING_UART2
default y
config BSP_USING_ARDUINO
bool "Compatible with Arduino Ecosystem (RTduino)"
select PKG_USING_RTDUINO
2022-05-01 12:24:35 +08:00
select BSP_USING_STLINK_TO_USART
select BSP_USING_GPIO
select BSP_USING_ADC
select BSP_USING_ADC1
select BSP_USING_PWM
select BSP_USING_PWM2
select BSP_USING_PWM2_CH2
select BSP_USING_PWM2_CH3
select BSP_USING_PWM3
select BSP_USING_PWM3_CH1
select BSP_USING_PWM3_CH2
select BSP_USING_PWM16
select BSP_USING_PWM16_CH1
select BSP_USING_PWM17
select BSP_USING_PWM17_CH1
select BSP_USING_I2C
select BSP_USING_I2C1
select BSP_USING_SPI
select BSP_USING_SPI1
select BSP_SPI1_TX_USING_DMA
select BSP_SPI1_RX_USING_DMA
select RTDUINO_USING_WIRE
select RTDUINO_USING_SPI
imply RTDUINO_USING_SERVO
default n
2019-05-30 18:00:03 +08:00
endmenu
menu "On-chip Peripheral Drivers"
config BSP_USING_GPIO
bool "Enable GPIO"
select RT_USING_PIN
default y
menuconfig BSP_USING_UART
bool "Enable UART"
default y
select RT_USING_SERIAL
if BSP_USING_UART
config BSP_USING_UART1
bool "Enable UART1"
default n
config BSP_UART1_RX_USING_DMA
bool "Enable UART1 RX DMA"
depends on BSP_USING_UART1 && RT_SERIAL_USING_DMA
default n
2021-04-25 14:23:05 +08:00
config BSP_USING_UART2
2019-05-30 18:00:03 +08:00
bool "Enable UART2"
default n
2019-05-30 18:00:03 +08:00
config BSP_UART2_RX_USING_DMA
bool "Enable UART2 RX DMA"
depends on BSP_USING_UART2 && RT_SERIAL_USING_DMA
default n
endif
menuconfig BSP_USING_ADC
bool "Enable ADC"
default n
select RT_USING_ADC
if BSP_USING_ADC
config BSP_USING_ADC1
bool "Enable ADC1"
default n
endif
menuconfig BSP_USING_TIM
bool "Enable timer"
default n
select RT_USING_HWTIMER
if BSP_USING_TIM
config BSP_USING_TIM7
bool "Enable TIM7"
default n
endif
menuconfig BSP_USING_PWM
bool "Enable PWM"
default n
select RT_USING_PWM
if BSP_USING_PWM
menuconfig BSP_USING_PWM2
bool "Enable timer2 output PWM"
default n
if BSP_USING_PWM2
config BSP_USING_PWM2_CH2
bool "Enable PWM2 channel2"
default n
config BSP_USING_PWM2_CH3
bool "Enable PWM2 channel3"
default n
endif
menuconfig BSP_USING_PWM3
bool "Enable timer3 output PWM"
default n
if BSP_USING_PWM3
config BSP_USING_PWM3_CH1
bool "Enable PWM3 channel1"
default n
config BSP_USING_PWM3_CH2
bool "Enable PWM3 channel2"
default n
endif
menuconfig BSP_USING_PWM16
bool "Enable timer16 output PWM"
default n
if BSP_USING_PWM16
config BSP_USING_PWM16_CH1
bool "Enable PWM16 channel1"
default n
endif
menuconfig BSP_USING_PWM17
bool "Enable timer17 output PWM"
default n
if BSP_USING_PWM17
config BSP_USING_PWM17_CH1
bool "Enable PWM17 channel1"
default n
endif
endif
menuconfig BSP_USING_I2C
bool "Enable I2C BUS"
default n
select RT_USING_I2C
select RT_USING_I2C_BITOPS
select RT_USING_PIN
if BSP_USING_I2C
config BSP_USING_I2C1
bool "Enable I2C1 Bus (User I2C)"
default n
if BSP_USING_I2C1
2023-01-09 10:14:23 +08:00
comment "Notice: PB9 --> 25; PB8 --> 24"
config BSP_I2C1_SCL_PIN
int "i2c1 SCL pin number"
range 1 176
default 24
config BSP_I2C1_SDA_PIN
int "i2c1 SDA pin number"
range 1 176
default 25
endif
endif
source "$(BSP_DIR)/../libraries/HAL_Drivers/drivers/Kconfig"
2023-01-09 10:14:23 +08:00
2019-05-30 18:00:03 +08:00
endmenu
menu "Board extended module Drivers"
endmenu
endmenu