rt-thread-official/bsp/efm32/EFM32GG_DK3750/trace.c

/**************************************************************************//**
 * @file
 * @brief API for enabling SWO or ETM trace on DK3750 board
 * @author Energy Micro AS
 * @version 1.2.2
 ******************************************************************************
 * @section License
 * <b>(C) Copyright 2011 Energy Micro AS, http://www.energymicro.com</b>
 ******************************************************************************
 *
 * This source code is the property of Energy Micro AS. The source and compiled
 * code may only be used on Energy Micro "EFM32" microcontrollers.
 *
 * This copyright notice may not be removed from the source code nor changed.
 *
 * DISCLAIMER OF WARRANTY/LIMITATION OF REMEDIES: Energy Micro AS has no
 * obligation to support this Software. Energy Micro AS is providing the
 * Software "AS IS", with no express or implied warranties of any kind,
 * including, but not limited to, any implied warranties of merchantability
 * or fitness for any particular purpose or warranties against infringement
 * of any proprietary rights of a third party.
 *
 * Energy Micro AS will not be liable for any consequential, incidental, or
 * special damages, or any other relief, or for any claim by any third party,
 * arising from your use of this Software.
 *
 *****************************************************************************/

/***************************************************************************//**
 * @addtogroup BSP
 * @{
 ******************************************************************************/

#include "efm32.h"
#include "efm32_gpio.h"
#include "efm32_cmu.h"

/**************************************************************************//**
 * @brief Configure EFM32GG990F1024 for DK3750 ETM trace output
 * @note You need to configure ETM trace on on kit config menu as well!
 *****************************************************************************/
void TRACE_ETMSetup(void)
{
  /* Enable peripheral clocks */
  CMU->HFCORECLKEN0 |= CMU_HFCORECLKEN0_LE;
  CMU->HFPERCLKEN0  |= CMU_HFPERCLKEN0_GPIO;
  CMU->OSCENCMD      = CMU_OSCENCMD_AUXHFRCOEN;

  /* Wait until AUXHFRCO clock is ready */
  while (!(CMU->STATUS & CMU_STATUS_AUXHFRCORDY)) ;

  /* Enable Port D, pins 3,4,5,6 for ETM Trace Data output */
  GPIO->P[3].MODEL = (GPIO->P[3].MODEL & ~_GPIO_P_MODEL_MODE3_MASK) | GPIO_P_MODEL_MODE3_PUSHPULL;
  GPIO->P[3].MODEL = (GPIO->P[3].MODEL & ~_GPIO_P_MODEL_MODE4_MASK) | GPIO_P_MODEL_MODE4_PUSHPULL;
  GPIO->P[3].MODEL = (GPIO->P[3].MODEL & ~_GPIO_P_MODEL_MODE5_MASK) | GPIO_P_MODEL_MODE5_PUSHPULL;
  GPIO->P[3].MODEL = (GPIO->P[3].MODEL & ~_GPIO_P_MODEL_MODE6_MASK) | GPIO_P_MODEL_MODE6_PUSHPULL;

  /* Enable Port D, pin 7 for DBG_TCLK */
  GPIO->P[3].MODEL = (GPIO->P[3].MODEL & ~_GPIO_P_MODEL_MODE7_MASK) | GPIO_P_MODEL_MODE7_PUSHPULL;

  /* Configure trace output for alternate location */
  GPIO->ROUTE = GPIO->ROUTE | GPIO_ROUTE_TCLKPEN | GPIO_ROUTE_TD0PEN | GPIO_ROUTE_TD1PEN
                | GPIO_ROUTE_TD2PEN | GPIO_ROUTE_TD3PEN
                | GPIO_ROUTE_ETMLOCATION_LOC0;
}


/**************************************************************************//**
 * @brief Configure EFM32GG990F1024 for DK3750 SWO trace output
 *****************************************************************************/
void TRACE_SWOSetup(void)
{
  /* Debug logic registers */
  volatile uint32_t *dwt_ctrl = (uint32_t *) 0xE0001000;
  volatile uint32_t *tpiu_prescaler = (uint32_t *) 0xE0040010;
  volatile uint32_t *tpiu_protocol = (uint32_t *) 0xE00400F0;

  /* Enable GPIO clock */
  CMU->HFPERCLKEN0 |= CMU_HFPERCLKEN0_GPIO;

  /* Enable Serial wire output pin */
  GPIO->ROUTE |= GPIO_ROUTE_SWOPEN;

  /* Set location 0 */
  GPIO->ROUTE = (GPIO->ROUTE & ~(_GPIO_ROUTE_SWLOCATION_MASK)) | GPIO_ROUTE_SWLOCATION_LOC0;

  /* Enable output on pin - GPIO Port F, Pin 2 */
  GPIO->P[5].MODEL &= ~(_GPIO_P_MODEL_MODE2_MASK);
  GPIO->P[5].MODEL |= GPIO_P_MODEL_MODE2_PUSHPULL;

  /* Enable debug clock AUXHFRCO */
  CMU->OSCENCMD = CMU_OSCENCMD_AUXHFRCOEN;

  /* Wait until clock is ready */
  while(!(CMU->STATUS & CMU_STATUS_AUXHFRCORDY));

  /* Enable trace in core debug */
  CoreDebug->DHCSR |= 1;
  CoreDebug->DEMCR |= CoreDebug_DEMCR_TRCENA_Msk;

  /* Enable PC and IRQ sampling output */
  *dwt_ctrl = 0x400113FF;

  /* Set TPIU prescaler to 16. */
  *tpiu_prescaler = 0xf;

  /* Set protocol to NRZ */
  *tpiu_protocol = 2;

  /* Unlock ITM and output data */
  ITM->LAR = 0xC5ACCE55;
  ITM->TCR = 0x10009;
}

/** @} (end group BSP) */