rt-thread-official/bsp/imxrt/imxrt1052-nxp-evk/board/Kconfig

menu "Hardware Drivers Config"

config BSP_USING_HYPERFLASH
    bool
    default n

config SOC_MIMXRT1052DVL6B
    bool
    select SOC_MIMXRT1050_SERIES
    select BSP_USING_HYPERFLASH
    select RT_USING_COMPONENTS_INIT
    select RT_USING_USER_MAIN
    default y

menu "On-chip Peripheral Drivers"

    config BSP_USING_DMA
        bool "Enable DMA"
        default n

    config BSP_USING_GPIO
        bool "Enable GPIO"
        select RT_USING_PIN
        default y

    menuconfig BSP_USING_LPUART
        bool "Enable UART"
        select RT_USING_SERIAL
        default y

        if BSP_USING_LPUART
            config BSP_USING_LPUART1
                bool "Enable LPUART1"
                default y

                config BSP_LPUART1_RX_USING_DMA
                    bool "Enable LPUART1 RX DMA"
                    depends on BSP_USING_LPUART1
                    select BSP_USING_DMA
                    select RT_SERIAL_USING_DMA
                    default n

                    config BSP_LPUART1_RX_DMA_CHANNEL
                        depends on BSP_LPUART1_RX_USING_DMA
                        int "Set LPUART1 RX DMA channel (0-32)"
                        default 0

                config BSP_LPUART1_TX_USING_DMA
                    bool "Enable LPUART1 TX DMA"
                    depends on BSP_USING_LPUART1
                    select BSP_USING_DMA
                    select RT_SERIAL_USING_DMA
                    default n

                    config BSP_LPUART1_TX_DMA_CHANNEL
                        depends on BSP_LPUART1_TX_USING_DMA
                        int "Set LPUART1 TX DMA channel (0-32)"
                        default 1

            config BSP_USING_LPUART3
                bool "Enable LPUART3"
                default n

                config BSP_LPUART3_RX_USING_DMA
                    bool "Enable LPUART3 RX DMA"
                    depends on BSP_USING_LPUART3
                    select BSP_USING_DMA
                    select RT_SERIAL_USING_DMA
                    default n

                    config BSP_LPUART3_RX_DMA_CHANNEL
                        depends on BSP_LPUART3_RX_USING_DMA
                        int "Set LPUART3 RX DMA channel (0-32)"
                        default 0

                config BSP_LPUART3_TX_USING_DMA
                    bool "Enable LPUART3 TX DMA"
                    depends on BSP_USING_LPUART3
                    select BSP_USING_DMA
                    select RT_SERIAL_USING_DMA
                    default n

                    config BSP_LPUART3_TX_DMA_CHANNEL
                        depends on BSP_LPUART3_TX_USING_DMA
                        int "Set LPUART3 TX DMA channel (0-32)"
                        default 1
        endif

    menuconfig BSP_USING_I2C
        bool "Enable I2C"
        select RT_USING_I2C
        default n
        if BSP_USING_I2C
            config BSP_USING_I2C1
                bool "Enable I2C1"
                default n
            choice
                prompt "Select I2C1 badurate"
                default HW_I2C1_BADURATE_100kHZ

                config HW_I2C1_BADURATE_100kHZ
                    bool "Badurate 100kHZ"

                config HW_I2C1_BADURATE_400kHZ
                    bool "Badurate 400kHZ"
            endchoice
        endif
endmenu

menu "Onboard Peripheral Drivers"

    config BSP_USING_SDRAM
        bool "Enable SDRAM"
        default n

    menuconfig BSP_USING_ETH
    bool "Enable Ethernet"
    select RT_USING_NETDEV
    select RT_USING_LWIP
    default n


    if BSP_USING_ETH
        config BSP_USING_PHY
            select RT_USING_PHY
            bool "Enable ethernet phy"
            default y

        if BSP_USING_PHY
            config PHY_DEVICE_ADDRESS
                int "Specify address of phy device"
                default 2

            config PHY_USING_KSZ8081
                bool "i.MX RT1064EVK uses ksz8081 phy"
                default y

            if PHY_USING_KSZ8081
                config PHY_RESET_PORT
                    int "indicate port of reset"
                    default 1

                config PHY_RESET_PIN
                    int "indicate pin of reset"
                    default 9

                config FSL_FEATURE_PHYKSZ8081_USE_RMII50M_MODE
                    bool "Enable the PHY ksz8081 RMII50M mode"
                    depends on PHY_USING_KSZ8081
                    default y
            endif

        endif
    endif

    menuconfig BSP_USING_AUDIO
    bool "Enable AUDIO (WM8960)"
    select BSP_USING_I2C1
    select RT_USING_AUDIO
    default n

    if BSP_USING_AUDIO
        config BSP_USING_AUDIO_PLAY
            bool "Enable Audio Play"
            default y
        if BSP_USING_AUDIO_PLAY
            config BSP_AUDIO_USING_DMA
                bool "Enable AUDIO DMA"
                default y
        endif

        config BSP_USING_AUDIO_RECORD
            bool "Enable Audio Record"
            select BSP_USING_AUDIO_PLAY
            default n
        if BSP_USING_AUDIO_RECORD
            config BSP_AUDIO_USING_DMA
                bool "Enable AUDIO DMA"
                default n
        endif
    endif
endmenu

menu "Board extended module Drivers"

endmenu

endmenu
[bsp/nxp] add new imxrt series 2019-06-12 15:01:12 +08:00			`menu "Hardware Drivers Config"`

			`config BSP_USING_HYPERFLASH`
			`bool`
			`default n`

			`config SOC_MIMXRT1052DVL6B`
			`bool`
			`select SOC_MIMXRT1050_SERIES`
			`select BSP_USING_HYPERFLASH`
[bsp][Kconfig]在bsp的Kconfig中select组件初始化与user main的选项 2019-09-11 12:06:43 +08:00			`select RT_USING_COMPONENTS_INIT`
			`select RT_USING_USER_MAIN`
[bsp/nxp] add new imxrt series 2019-06-12 15:01:12 +08:00			`default y`

			`menu "On-chip Peripheral Drivers"`

			`config BSP_USING_DMA`
			`bool "Enable DMA"`
			`default n`
增加双网口配置选项，增加phy8211F 驱动 (#6278) * Update Kconfig 增加RT1170双路网络选项 * Update SConscript 增加RTL8211F驱动选项支持 * Update SConstruct 去掉外设目录 * Add files via upload 增加PHY芯片RTL8211F驱动 * Update drv_rtl8211f.c * format code Co-authored-by: Meco Man <920369182@qq.com> 2022-08-15 11:21:27 +08:00
[bsp/nxp] add new imxrt series 2019-06-12 15:01:12 +08:00			`config BSP_USING_GPIO`
			`bool "Enable GPIO"`
			`select RT_USING_PIN`
			`default y`

			`menuconfig BSP_USING_LPUART`
			`bool "Enable UART"`
			`select RT_USING_SERIAL`
			`default y`
增加双网口配置选项，增加phy8211F 驱动 (#6278) * Update Kconfig 增加RT1170双路网络选项 * Update SConscript 增加RTL8211F驱动选项支持 * Update SConstruct 去掉外设目录 * Add files via upload 增加PHY芯片RTL8211F驱动 * Update drv_rtl8211f.c * format code Co-authored-by: Meco Man <920369182@qq.com> 2022-08-15 11:21:27 +08:00
[bsp/nxp] add new imxrt series 2019-06-12 15:01:12 +08:00			`if BSP_USING_LPUART`
			`config BSP_USING_LPUART1`
			`bool "Enable LPUART1"`
			`default y`

			`config BSP_LPUART1_RX_USING_DMA`
			`bool "Enable LPUART1 RX DMA"`
			`depends on BSP_USING_LPUART1`
			`select BSP_USING_DMA`
			`select RT_SERIAL_USING_DMA`
			`default n`

			`config BSP_LPUART1_RX_DMA_CHANNEL`
			`depends on BSP_LPUART1_RX_USING_DMA`
			`int "Set LPUART1 RX DMA channel (0-32)"`
			`default 0`

			`config BSP_LPUART1_TX_USING_DMA`
			`bool "Enable LPUART1 TX DMA"`
			`depends on BSP_USING_LPUART1`
			`select BSP_USING_DMA`
			`select RT_SERIAL_USING_DMA`
			`default n`

			`config BSP_LPUART1_TX_DMA_CHANNEL`
			`depends on BSP_LPUART1_TX_USING_DMA`
			`int "Set LPUART1 TX DMA channel (0-32)"`
			`default 1`
imxrt:board: Add LPUART3 item for imxrt1052-nxp-evk Add LPUART3 item in imxrt1052-nxp-evk Kconfig file to support Arduino UART interface. Signed-off-by: Gavin Liu <gavin-liugang@outlook.com> 2019-09-16 18:26:37 +08:00
			`config BSP_USING_LPUART3`
			`bool "Enable LPUART3"`
			`default n`

			`config BSP_LPUART3_RX_USING_DMA`
			`bool "Enable LPUART3 RX DMA"`
			`depends on BSP_USING_LPUART3`
			`select BSP_USING_DMA`
			`select RT_SERIAL_USING_DMA`
			`default n`

			`config BSP_LPUART3_RX_DMA_CHANNEL`
			`depends on BSP_LPUART3_RX_USING_DMA`
			`int "Set LPUART3 RX DMA channel (0-32)"`
			`default 0`

			`config BSP_LPUART3_TX_USING_DMA`
			`bool "Enable LPUART3 TX DMA"`
			`depends on BSP_USING_LPUART3`
			`select BSP_USING_DMA`
			`select RT_SERIAL_USING_DMA`
			`default n`

			`config BSP_LPUART3_TX_DMA_CHANNEL`
			`depends on BSP_LPUART3_TX_USING_DMA`
			`int "Set LPUART3 TX DMA channel (0-32)"`
			`default 1`
/Add SAI and sdcard driver to i.MXRT1050 board/ 2020-01-14 16:09:11 +08:00			`endif`
[bsp/nxp] add new imxrt series 2019-06-12 15:01:12 +08:00
/Add SAI and sdcard driver to i.MXRT1050 board/ 2020-01-14 16:09:11 +08:00			`menuconfig BSP_USING_I2C`
			`bool "Enable I2C"`
			`select RT_USING_I2C`
			`default n`
			`if BSP_USING_I2C`
			`config BSP_USING_I2C1`
			`bool "Enable I2C1"`
			`default n`
			`choice`
			`prompt "Select I2C1 badurate"`
			`default HW_I2C1_BADURATE_100kHZ`

			`config HW_I2C1_BADURATE_100kHZ`
			`bool "Badurate 100kHZ"`

			`config HW_I2C1_BADURATE_400kHZ`
			`bool "Badurate 400kHZ"`
			`endchoice`
			`endif`
[bsp/nxp] add new imxrt series 2019-06-12 15:01:12 +08:00			`endmenu`

			`menu "Onboard Peripheral Drivers"`

imxrt:sdram: Add sdram support for imxrt1052-nxp-evk 1. Add sdram item in bsp/imxrt/imxrt1052-nxp-evk/board/Kconfig 2. Add sdram configuration header file for imxrt1052-nxp-evk 3. Update the sdram space assignment for memheap Signed-off-by: Gavin Liu <gavin-liugang@outlook.com> 2019-09-16 18:56:09 +08:00			`config BSP_USING_SDRAM`
			`bool "Enable SDRAM"`
			`default n`

imxrt:enet: Support imxrt ethernet interface 1. Add "drv_eth.c" for all imxrt platforms. 2. Add ksz8081 phy driver for imxrt1052-nxp-evk board. 3. Disable the LED demo in main.c file if enable the ENET and ksz8081 phy, because the PINs of LED and ksz8081 reset are from the same GPIO. 4. Update the relevant Kconfig and Sconscript files. Signed-off-by: Gavin Liu <gavin-liugang@outlook.com> 2019-09-19 10:11:57 +08:00			`menuconfig BSP_USING_ETH`
增加双网口配置选项，增加phy8211F 驱动 (#6278) * Update Kconfig 增加RT1170双路网络选项 * Update SConscript 增加RTL8211F驱动选项支持 * Update SConstruct 去掉外设目录 * Add files via upload 增加PHY芯片RTL8211F驱动 * Update drv_rtl8211f.c * format code Co-authored-by: Meco Man <920369182@qq.com> 2022-08-15 11:21:27 +08:00			`bool "Enable Ethernet"`
			`select RT_USING_NETDEV`
			`select RT_USING_LWIP`
			`default n`


			`if BSP_USING_ETH`
			`config BSP_USING_PHY`
修改了imxrt1052-nxp-evk的BSP的以太网相关配置，用于适配PHY模型 2020-10-12 19:11:38 +08:00			`select RT_USING_PHY`
增加双网口配置选项，增加phy8211F 驱动 (#6278) * Update Kconfig 增加RT1170双路网络选项 * Update SConscript 增加RTL8211F驱动选项支持 * Update SConstruct 去掉外设目录 * Add files via upload 增加PHY芯片RTL8211F驱动 * Update drv_rtl8211f.c * format code Co-authored-by: Meco Man <920369182@qq.com> 2022-08-15 11:21:27 +08:00			`bool "Enable ethernet phy"`
			`default y`
imxrt:enet: Support imxrt ethernet interface 1. Add "drv_eth.c" for all imxrt platforms. 2. Add ksz8081 phy driver for imxrt1052-nxp-evk board. 3. Disable the LED demo in main.c file if enable the ENET and ksz8081 phy, because the PINs of LED and ksz8081 reset are from the same GPIO. 4. Update the relevant Kconfig and Sconscript files. Signed-off-by: Gavin Liu <gavin-liugang@outlook.com> 2019-09-19 10:11:57 +08:00
增加双网口配置选项，增加phy8211F 驱动 (#6278) * Update Kconfig 增加RT1170双路网络选项 * Update SConscript 增加RTL8211F驱动选项支持 * Update SConstruct 去掉外设目录 * Add files via upload 增加PHY芯片RTL8211F驱动 * Update drv_rtl8211f.c * format code Co-authored-by: Meco Man <920369182@qq.com> 2022-08-15 11:21:27 +08:00			`if BSP_USING_PHY`
修改了imxrt1052-nxp-evk的BSP的以太网相关配置，用于适配PHY模型 2020-10-12 19:11:38 +08:00			`config PHY_DEVICE_ADDRESS`
			`int "Specify address of phy device"`
			`default 2`

			`config PHY_USING_KSZ8081`
			`bool "i.MX RT1064EVK uses ksz8081 phy"`
			`default y`

			`if PHY_USING_KSZ8081`
			`config PHY_RESET_PORT`
			`int "indicate port of reset"`
			`default 1`

			`config PHY_RESET_PIN`
			`int "indicate pin of reset"`
			`default 9`
增加双网口配置选项，增加phy8211F 驱动 (#6278) * Update Kconfig 增加RT1170双路网络选项 * Update SConscript 增加RTL8211F驱动选项支持 * Update SConstruct 去掉外设目录 * Add files via upload 增加PHY芯片RTL8211F驱动 * Update drv_rtl8211f.c * format code Co-authored-by: Meco Man <920369182@qq.com> 2022-08-15 11:21:27 +08:00
修改了imxrt1052-nxp-evk的BSP的以太网相关配置，用于适配PHY模型 2020-10-12 19:11:38 +08:00			`config FSL_FEATURE_PHYKSZ8081_USE_RMII50M_MODE`
			`bool "Enable the PHY ksz8081 RMII50M mode"`
			`depends on PHY_USING_KSZ8081`
			`default y`
			`endif`

			`endif`
增加双网口配置选项，增加phy8211F 驱动 (#6278) * Update Kconfig 增加RT1170双路网络选项 * Update SConscript 增加RTL8211F驱动选项支持 * Update SConstruct 去掉外设目录 * Add files via upload 增加PHY芯片RTL8211F驱动 * Update drv_rtl8211f.c * format code Co-authored-by: Meco Man <920369182@qq.com> 2022-08-15 11:21:27 +08:00			`endif`

$WBI\nxf44444$ audio_kconfig 2020-11-17 12:49:27 +08:00			`menuconfig BSP_USING_AUDIO`
			`bool "Enable AUDIO (WM8960)"`
			`select BSP_USING_I2C1`
			`select RT_USING_AUDIO`
			`default n`
增加双网口配置选项，增加phy8211F 驱动 (#6278) * Update Kconfig 增加RT1170双路网络选项 * Update SConscript 增加RTL8211F驱动选项支持 * Update SConstruct 去掉外设目录 * Add files via upload 增加PHY芯片RTL8211F驱动 * Update drv_rtl8211f.c * format code Co-authored-by: Meco Man <920369182@qq.com> 2022-08-15 11:21:27 +08:00
$WBI\nxf44444$ audio_kconfig 2020-11-17 12:49:27 +08:00			`if BSP_USING_AUDIO`
			`config BSP_USING_AUDIO_PLAY`
/Add SAI and sdcard driver to i.MXRT1050 board/ 2020-01-14 16:09:11 +08:00			`bool "Enable Audio Play"`
			`default y`
$WBI\nxf44444$ audio_kconfig 2020-11-17 12:49:27 +08:00			`if BSP_USING_AUDIO_PLAY`
			`config BSP_AUDIO_USING_DMA`
			`bool "Enable AUDIO DMA"`
			`default y`
			`endif`
/Add SAI and sdcard driver to i.MXRT1050 board/ 2020-01-14 16:09:11 +08:00
$WBI\nxf44444$ audio_kconfig 2020-11-17 12:49:27 +08:00			`config BSP_USING_AUDIO_RECORD`
/Add SAI and sdcard driver to i.MXRT1050 board/ 2020-01-14 16:09:11 +08:00			`bool "Enable Audio Record"`
			`select BSP_USING_AUDIO_PLAY`
			`default n`
$WBI\nxf44444$ audio_kconfig 2020-11-17 12:49:27 +08:00			`if BSP_USING_AUDIO_RECORD`
			`config BSP_AUDIO_USING_DMA`
			`bool "Enable AUDIO DMA"`
			`default n`
增加双网口配置选项，增加phy8211F 驱动 (#6278) * Update Kconfig 增加RT1170双路网络选项 * Update SConscript 增加RTL8211F驱动选项支持 * Update SConstruct 去掉外设目录 * Add files via upload 增加PHY芯片RTL8211F驱动 * Update drv_rtl8211f.c * format code Co-authored-by: Meco Man <920369182@qq.com> 2022-08-15 11:21:27 +08:00			`endif`
			`endif`
[bsp/nxp] add new imxrt series 2019-06-12 15:01:12 +08:00			`endmenu`

			`menu "Board extended module Drivers"`

			`endmenu`

修复board/Kconfig的错误 2021-05-03 09:26:45 +08:00			`endmenu`