rt-thread-official/bsp/stm32/stm32h750-armfly-h7-tool/board/Kconfig

141 lines
3.2 KiB
Plaintext
Raw Normal View History

2019-10-25 16:19:28 +08:00
menu "Hardware Drivers Config"
menu "Onboard Peripheral Drivers"
2019-10-26 02:42:18 +08:00
config BSP_USING_QSPI_FLASH
bool "Enable QSPI FLASH (W25Q256)"
select BSP_USING_QSPI
select RT_USING_SFUD
select RT_SFUD_USING_QSPI
default n
config PHY_USING_LAN8720A
bool
menuconfig BSP_USING_ETH
bool "Enable Ethernet"
select RT_USING_LWIP
select PHY_USING_LAN8720A
default n
config BSP_USING_LCD
bool "Enable LCD"
select BSP_USING_PWM
default n
2019-10-26 02:42:18 +08:00
config BSP_USING_ESP32
bool "Enable ESP32"
select BSP_USING_UART4
select RT_USING_AT
select AT_USING_CLIENT
select AT_USING_SOCKET
select PKG_USING_AT_DEVICE
select AT_DEVICE_USING_ESP32
default n
2019-10-25 16:19:28 +08:00
endmenu
menu "On-chip Peripheral Drivers"
config BSP_USING_GPIO
bool "Enable GPIO"
select RT_USING_PIN
default y
menuconfig BSP_USING_UART
bool "Enable UART"
default y
select RT_USING_SERIAL
if BSP_USING_UART
config BSP_USING_UART1
bool "Enable UART1"
default y
2019-10-26 02:42:18 +08:00
config BSP_USING_UART4
bool "Enable UART4"
default y
2019-10-25 16:19:28 +08:00
endif
config BSP_USING_QSPI
bool "Enable QSPI BUS"
select RT_USING_QSPI
select RT_USING_SPI
default n
config BSP_QSPI_USING_DMA
bool "Enable QSPI DMA support"
default n
menuconfig BSP_USING_I2C1
bool "Enable I2C1 BUS (software simulation)"
default n
select RT_USING_I2C
select RT_USING_I2C_BITOPS
select RT_USING_PIN
if BSP_USING_I2C1
config BSP_I2C1_SCL_PIN
int "i2c1 scl pin number"
range 1 216
default 135
config BSP_I2C1_SDA_PIN
int "I2C1 sda pin number"
range 1 216
default 95
endif
menuconfig BSP_USING_PWM
bool "Enable PWM"
default n
select RT_USING_PWM
if BSP_USING_PWM
menuconfig BSP_USING_PWM2
bool "Enable timer2 output PWM"
default n
if BSP_USING_PWM2
config BSP_USING_PWM2_CH2
bool "Enable PWM2 channel2"
default n
endif
endif
menuconfig BSP_USING_ADC
bool "Enable ADC"
default n
select RT_USING_ADC
if BSP_USING_ADC
config BSP_USING_ADC1
bool "Enable ADC1"
default n
config BSP_USING_ADC2
bool "Enable ADC2"
default n
config BSP_USING_ADC3
bool "Enable ADC3"
default n
endif
config BSP_USING_SDIO
bool "Enable SDIO"
select RT_USING_SDIO
select RT_USING_DFS
default n
config BSP_USING_USBD
bool "Enable OTGHS as USB device"
select RT_USING_USB_DEVICE
select BSP_USBD_TYPE_HS
select BSP_USBD_SPEED_HS
select BSP_USBD_PHY_ULPI
default n
source "$(BSP_DIR)/../libraries/HAL_Drivers/drivers/Kconfig"
2019-10-25 16:19:28 +08:00
endmenu
menu "Board extended module Drivers"
endmenu
endmenu