rt-thread-official/bsp/stm32/stm32h750-artpi-h750/board/Kconfig

128 lines
3.7 KiB
Plaintext
Raw Normal View History

2020-11-22 14:51:43 +08:00
menu "Hardware Drivers Config"
config SOC_STM32H750XB
bool
select SOC_SERIES_STM32H7
select RT_USING_COMPONENTS_INIT
select RT_USING_USER_MAIN
default y
menu "Onboard Peripheral Drivers"
config BSP_USING_USB_TO_USART
bool "Enable Debuger USART (uart4)"
select BSP_USING_UART
select BSP_USING_UART4
default n
2020-11-22 14:51:43 +08:00
endmenu
menu "On-chip Peripheral Drivers"
config BSP_USING_GPIO
bool "Enable GPIO"
select RT_USING_PIN
default y
menuconfig BSP_USING_UART
bool "Enable UART"
default n
2020-11-22 14:51:43 +08:00
select RT_USING_SERIAL
select RT_SERIAL_USING_DMA
2020-11-22 14:51:43 +08:00
if BSP_USING_UART
config BSP_USING_UART1
bool "Enable UART1"
default n
config BSP_UART1_RX_USING_DMA
bool "Enable UART1 RX DMA"
depends on BSP_USING_UART1 && RT_SERIAL_USING_DMA
default n
config BSP_UART1_TX_USING_DMA
bool "Enable UART1 TX DMA"
depends on BSP_USING_UART1 && RT_SERIAL_USING_DMA
default n
2020-11-25 00:09:50 +08:00
config BSP_USING_UART3
bool "Enable UART3"
default n
2020-11-22 14:51:43 +08:00
config BSP_USING_UART4
bool "Enable UART4"
default n
config BSP_USING_UART6
bool "Enable UART6"
default n
2020-11-22 14:51:43 +08:00
endif
config BSP_USING_ONCHIP_RTC
bool "Enable Onchip RTC"
select RT_USING_RTC
default n
2020-11-22 14:51:43 +08:00
menuconfig BSP_USING_I2C
bool "Enable I2C BUS (software simulation)"
select RT_USING_I2C
select RT_USING_I2C_BITOPS
select RT_USING_PIN
default n
if BSP_USING_I2C
menuconfig BSP_USING_I2C1
bool "Enable I2C1 BUS (software simulation)"
default n
select RT_USING_I2C
select RT_USING_I2C_BITOPS
select RT_USING_PIN
if BSP_USING_I2C1
comment "Notice: PB6 --> 22; PB7 --> 23"
config BSP_I2C1_SCL_PIN
int "I2C1 scl pin number"
range 0 175
default 22
config BSP_I2C1_SDA_PIN
int "I2C1 sda pin number"
range 0 175
default 23
endif
menuconfig BSP_USING_I2C2
bool "Enable I2C2 BUS (software simulation)"
default n
if BSP_USING_I2C2
comment "Notice: PH13 --> 125; PH15 --> 127"
config BSP_I2C2_SCL_PIN
int "i2c2 scl pin number"
range 1 176
default 127
config BSP_I2C2_SDA_PIN
int "I2C2 sda pin number"
range 0 175
default 125
endif
menuconfig BSP_USING_I2C3
bool "Enable I2C3 BUS (software simulation)"
default n
if BSP_USING_I2C3
comment "Notice: PH12 --> 124; PH11 --> 123"
config BSP_I2C3_SCL_PIN
int "i2c3 scl pin number"
range 0 175
default 123
config BSP_I2C3_SDA_PIN
int "I2C3 sda pin number"
range 0 175
default 124
endif
endif
2020-11-22 14:51:43 +08:00
source "../libraries/HAL_Drivers/Kconfig"
endmenu
menu "Board extended module Drivers"
endmenu
endmenu