/**
@page GPIO_EXTI GPIO EXTI example
@verbatim
******************** (C) COPYRIGHT 2016 STMicroelectronics *******************
* @file GPIO/GPIO_EXTI/readme.txt
* @author MCD Application Team
* @brief Description of the GPIO EXTI example.
******************************************************************************
*
* Redistribution and use in source and binary forms, with or without modification,
* are permitted provided that the following conditions are met:
* 1. Redistributions of source code must retain the above copyright notice,
* this list of conditions and the following disclaimer.
* 2. Redistributions in binary form must reproduce the above copyright notice,
* this list of conditions and the following disclaimer in the documentation
* and/or other materials provided with the distribution.
* 3. Neither the name of STMicroelectronics nor the names of its contributors
* may be used to endorse or promote products derived from this software
* without specific prior written permission.
*
* THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS "AS IS"
* AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE
* IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE
* DISCLAIMED. IN NO EVENT SHALL THE COPYRIGHT HOLDER OR CONTRIBUTORS BE LIABLE
* FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL
* DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR
* SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER
* CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY,
* OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE
* OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.
*
******************************************************************************
@endverbatim
@par Example Description
This example shows how to configure external interrupt lines.
In this example, 1 EXTI line (EXTI_Line4_15) is configured to generate
an interrupt on each rising edge.
In the interrupt routine a led connected to a specific GPIO pin is toggled.
In this example:
- EXTI_Line4_15 is connected to PC.13 pin
- when falling edge is detected on EXTI_Line4_15 by pressing User push-button, LED2 toggles
On STM32F091RC-Nucleo RevC:
- EXTI_Line4_15 is connected to User push-button
In this example, HCLK is configured at 48 MHz.
@note Care must be taken when using HAL_Delay(), this function provides accurate delay (in milliseconds)
based on variable incremented in SysTick ISR. This implies that if HAL_Delay() is called from
a peripheral ISR process, then the SysTick interrupt must have higher priority (numerically lower)
than the peripheral interrupt. Otherwise the caller ISR process will be blocked.
To change the SysTick interrupt priority you have to use HAL_NVIC_SetPriority() function.
@note The application need to ensure that the SysTick time base is always set to 1 millisecond
to have correct HAL operation.
@par Directory contents
- GPIO/GPIO_EXTI/Inc/stm32f0xx_hal_conf.h HAL configuration file
- GPIO/GPIO_EXTI/Inc/stm32f0xx_it.h Interrupt handlers header file
- GPIO/GPIO_EXTI/Inc/main.h Header for main.c module
- GPIO/GPIO_EXTI/Src/stm32f0xx_it.c Interrupt handlers
- GPIO/GPIO_EXTI/Src/main.c Main program
- GPIO/GPIO_EXTI/Src/system_stm32f0xx.c STM32F0xx system source file
@par Hardware and Software environment
- This example runs on STM32F0xx devices.
- This example has been tested with STM32F091RC-Nucleo RevC board and can be
easily tailored to any other supported device and development board.
@par How to use it ?
In order to make the program work, you must do the following :
- Open your preferred toolchain
- Rebuild all files and load your image into target memory
- Run the example
* <h3><center>© COPYRIGHT STMicroelectronics</center></h3>
*/
chinky
45af88c4ae