168 lines
7.5 KiB
Plaintext
168 lines
7.5 KiB
Plaintext
/**
|
|
@page PWR_CurrentConsumption PWR Current Consumption example
|
|
|
|
@verbatim
|
|
******************** (C) COPYRIGHT 2016 STMicroelectronics *******************
|
|
* @file PWR/PWR_CurrentConsumption/readme.txt
|
|
* @author MCD Application Team
|
|
* @brief Description of the PWR Current Consumption example.
|
|
******************************************************************************
|
|
*
|
|
* Redistribution and use in source and binary forms, with or without modification,
|
|
* are permitted provided that the following conditions are met:
|
|
* 1. Redistributions of source code must retain the above copyright notice,
|
|
* this list of conditions and the following disclaimer.
|
|
* 2. Redistributions in binary form must reproduce the above copyright notice,
|
|
* this list of conditions and the following disclaimer in the documentation
|
|
* and/or other materials provided with the distribution.
|
|
* 3. Neither the name of STMicroelectronics nor the names of its contributors
|
|
* may be used to endorse or promote products derived from this software
|
|
* without specific prior written permission.
|
|
*
|
|
* THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS "AS IS"
|
|
* AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE
|
|
* IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE
|
|
* DISCLAIMED. IN NO EVENT SHALL THE COPYRIGHT HOLDER OR CONTRIBUTORS BE LIABLE
|
|
* FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL
|
|
* DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR
|
|
* SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER
|
|
* CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY,
|
|
* OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE
|
|
* OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.
|
|
*
|
|
******************************************************************************
|
|
@endverbatim
|
|
|
|
@par Example Description
|
|
|
|
This example shows how to configure the system to measure the current consumption
|
|
in different low power modes.
|
|
|
|
The Low Power modes are:
|
|
- SLEEP mode
|
|
- STOP mode with RTC
|
|
- STANDBY mode without RTC
|
|
- STANDBY mode with RTC
|
|
|
|
To run this example, the user has to follow the following steps:
|
|
1. Select the low power mode to be measured by uncommenting the corresponding
|
|
line inside the stm32f0xx_lp_modes.h file.
|
|
@code
|
|
/* #define SLEEP_MODE */
|
|
#define STOP_MODE_RTC
|
|
/* #define STANDBY_MODE */
|
|
/* #define STANDBY_RTC_MODE */
|
|
@endcode
|
|
|
|
2. Use an external amperemeter to measure the IDD current.
|
|
|
|
3. This example can not be used in DEBUG mode due to the fact that the
|
|
Cortex-M0 core is no longer clocked during low power mode and so debugging
|
|
features are not available.
|
|
|
|
Here below a detailed description of the example code:
|
|
|
|
@verbatim
|
|
|
|
1. After reset, the program waits for User push-button connected to the PC.13 pin
|
|
to be pressed to enter the selected low power mode.
|
|
- When the RTC is not used in the low power mode configuration, press
|
|
again the User push-button to exit the low power mode.
|
|
|
|
- When the RTC is used, the wakeup from low power mode is automatically
|
|
generated by the RTC (after 20s).
|
|
|
|
2. After exit from low power mode, the LED2 is blinking.
|
|
In the case of exit from stand-by mode, LED2 is first ON for two seconds before
|
|
starting blinking.
|
|
|
|
3. The sequence can be repeated from step 1 in following the same steps (pressing
|
|
the USER button to enter the desired low power mode)
|
|
|
|
In case of error, LED2 transmits a sequence of three dots, three dashes, three dots.
|
|
|
|
Low power modes description:
|
|
|
|
- Sleep Mode
|
|
============
|
|
- System Running at PLL (48 MHz)
|
|
- Flash 2 wait state
|
|
- Instruction and Data caches ON
|
|
- Prefetch OFF
|
|
- Code running from Internal FLASH
|
|
- All peripherals disabled.
|
|
- Wakeup using EXTI Line (User push-button PC.13)
|
|
|
|
- STOP Mode
|
|
===========
|
|
- RTC Clocked by LSE or LSI
|
|
- Regulator in LP mode
|
|
- HSI, HSE OFF and LSI if not used as RTC Clock source
|
|
- No IWDG
|
|
- Automatic Wakeup using RTC clocked by LSE/LSI (after ~20s)
|
|
|
|
|
|
- STANDBY Mode
|
|
==============
|
|
- RTC OFF
|
|
- IWDG and LSI OFF
|
|
- Wakeup using WakeUp Pin PWR_WAKEUP_PIN2 connected to PC.13
|
|
|
|
- STANDBY Mode with RTC clocked by LSE/LSI
|
|
==========================================
|
|
- RTC Clocked by LSE or LSI
|
|
- IWDG OFF and LSI OFF if not used as RTC Clock source
|
|
- Automatic Wakeup using RTC clocked by LSE/LSI (after ~20s)
|
|
|
|
|
|
@endverbatim
|
|
|
|
@note Care must be taken when using HAL_Delay(), this function provides accurate delay (in milliseconds)
|
|
based on variable incremented in SysTick ISR. This implies that if HAL_Delay() is called from
|
|
a peripheral ISR process, then the SysTick interrupt must have higher priority (numerically lower)
|
|
than the peripheral interrupt. Otherwise the caller ISR process will be blocked.
|
|
To change the SysTick interrupt priority you have to use HAL_NVIC_SetPriority() function.
|
|
|
|
@note The application need to ensure that the SysTick time base is always set to 1 millisecond
|
|
to have correct HAL operation.
|
|
|
|
@note Care must be taken when HAL_RCCEx_PeriphCLKConfig() is used to select the RTC clock source; in this
|
|
case the Backup domain will be reset in order to modify the RTC Clock source, as consequence RTC
|
|
registers (including the backup registers) and RCC_BDCR register are set to their reset values.
|
|
|
|
@par Directory contents
|
|
|
|
- PWR/PWR_CurrentConsumption/Inc/stm32f0xx_conf.h HAL Configuration file
|
|
- PWR/PWR_CurrentConsumption/Inc/stm32f0xx_it.h Header for stm32f0xx_it.c
|
|
- PWR/PWR_CurrentConsumption/Inc/main.h Header file for main.c
|
|
- PWR/PWR_CurrentConsumption/Inc/stm32f0xx_lp_modes.h STM32F0xx Low Power Modes header file
|
|
- PWR/PWR_CurrentConsumption/Src/stm32f0xx_it.c Interrupt handlers
|
|
- PWR/PWR_CurrentConsumption/Src/main.c Main program
|
|
- PWR/PWR_CurrentConsumption/Src/stm32f0xx_hal_msp.c HAL MSP module
|
|
- PWR/PWR_CurrentConsumption/Src/stm32f0xx_lp_modes.c STM32F0xx Low Power Modes source file
|
|
- PWR/PWR_CurrentConsumption/Src/system_stm32f0xx.c stm32f0xx system source file
|
|
|
|
@par Hardware and Software environment
|
|
|
|
- This example runs on STM32F072RB devices.
|
|
|
|
- This example has been tested with STM32F072RB-Nucleo RevC board embedding
|
|
a STM32F072RBT6 device and can be
|
|
easily tailored to any other supported device and development board.
|
|
|
|
- STM32F072RB-Nucleo RevC Set-up
|
|
- Use LED2 connected to PA.05 pin.
|
|
* LED2 toggles while waiting for the USER push-button to be pressed to enter the low power mode.
|
|
- Remove JP6 jumper and connect an amperemeter to JP6 to measure IDD current.
|
|
|
|
@par How to use it ?
|
|
|
|
In order to make the program work, you must do the following :
|
|
- Open your preferred toolchain
|
|
- Rebuild all files and load your image into target memory
|
|
- Run the example
|
|
|
|
|
|
* <h3><center>© COPYRIGHT STMicroelectronics</center></h3>
|
|
*/
|