#define ADC_DEV_NAME "adc1"    /* ADC 设备名称 */
#define ADC_DEV_CHANNEL 5      /* ADC 通道 */
#define ADC_DEV_CHANNEL1 6     /* ADC 通道 */
#define ADC_DEV_CHANNEL2 7     /* ADC 通道 */
#define REFER_VOLTAGE 330      /* 参考电压 3.3V,数据精度乘以100保留2位小数*/
#define CONVERT_BITS (1 << 12) /* 转换位数为12位 */
#include <rtthread.h>
#include <rtdevice.h>
#include <drv_gpio.h>

rt_thread_t Sensor_Thread = RT_NULL;

#define THREAD_PRIORITY 25
#define THREAD_STACK_SIZE 4096
#define THREAD_TIMESLICE 5

#define PM25_READ_TIMES	20
#define GPIO_PIN GET_PIN(G, 5) 

#define LOG_TAG "sensor"
#define DBG_LVL DBG_LOG
// #define DBG_LVL DBG_INFO

#define USE_LOG1
#define USE_LOG2
#define USE_LOG3
// #define USE_LOG4
#define USE_LOG5
// #define USE_LOG6
// #define USE_LOG_D
#include "logn.h"

float ADC_air;
float ADC_PM25;
float ADC_pressure;

float ADC_Read()
{
    rt_adc_device_t adc_dev; /* ADC 设备句柄 */
    rt_uint32_t value, vol;
    /* 查找设备 */
    adc_dev = (rt_adc_device_t)rt_device_find(ADC_DEV_NAME);
    /* 使能设备 */
    rt_adc_enable(adc_dev, ADC_DEV_CHANNEL);
    /* 读取采样值 */
    value = rt_adc_read(adc_dev, ADC_DEV_CHANNEL);

    return value;
}
float ADC1_Read()
{
    rt_adc_device_t adc_dev; /* ADC 设备句柄 */
    rt_uint32_t value, vol;
    /* 查找设备 */
    adc_dev = (rt_adc_device_t)rt_device_find(ADC_DEV_NAME);
    /* 使能设备 */
    rt_adc_enable(adc_dev, ADC_DEV_CHANNEL1);
    /* 读取采样值 */
    value = rt_adc_read(adc_dev, ADC_DEV_CHANNEL1);

    return value;
}
float ADC2_Read()
{
    rt_adc_device_t adc_dev; /* ADC 设备句柄 */
    rt_uint32_t value, vol;
    /* 查找设备 */
    adc_dev = (rt_adc_device_t)rt_device_find(ADC_DEV_NAME);
    /* 使能设备 */
    rt_adc_enable(adc_dev, ADC_DEV_CHANNEL2);
    /* 读取采样值 */
    value = rt_adc_read(adc_dev, ADC_DEV_CHANNEL2);

    return value;
}
float PM25_GetData(void)
{
	int ADCVal;
	int dustVal = 0;
	float Voltage;
 
    rt_pin_write(GPIO_PIN, PIN_HIGH);//置1  开启内部LED
   
	rt_hw_us_delay(280);
	ADCVal =  ADC1_Read();
	rt_hw_us_delay(25);			  
    rt_pin_write(GPIO_PIN, PIN_LOW);	//置0  关闭内部LED
	rt_hw_us_delay(9680);			//需要脉宽比0.32ms/10ms的PWM信号驱动传感器中的LED
	
	Voltage = 3.3f * ADCVal / 4096.f * 2; //获得AO输出口的电压值
	
	dustVal = (0.17*Voltage-0.1)*1000;  //乘以1000单位换成ug/m3//

	if (dustVal < 0)
		dustVal = 0;            //限位//

	if (dustVal>500)        
		dustVal=500;

	return dustVal;
}

/**
  * @brief  平均值滤波法
  * @param  无
  * @retval 返回滤波后的数据
  */
float Get_PM25_Average_Data(void)
{
	float temp_val=0;
	float t;
	for(t=0;t<PM25_READ_TIMES;t++)	//#define PM25_READ_TIMES	20	定义读取次数,读这么多次,然后取平均值
 
	{
		temp_val+=PM25_GetData();	//读取ADC值
		rt_thread_mdelay(5);
	}
	temp_val/=PM25_READ_TIMES;//得到平均值
    return temp_val;//返回算出的ADC平均值
}
static void sensor_thread(void *parameter)
{
    while (1)
    {
        ADC_air = ADC_Read();              // 空气质量传感器数值    0-4095    表示从差到优秀
        ADC_PM25 = Get_PM25_Average_Data(); // PM2.5传感器数值0-500  表示从优秀到查差
        ADC_pressure = ADC2_Read();             // 压力传感器数值     0-4095    表示从差到优秀
        LOG5("ADC_air:%f,ADC_PM25:%f,ADC_pressure:%f", ADC_air, ADC_PM25, ADC_pressure);
        rt_thread_mdelay(1000);
    }
}
void sensor_init(void)
{
    Sensor_Thread = rt_thread_create("sensor", sensor_thread, RT_NULL, THREAD_STACK_SIZE, THREAD_PRIORITY, THREAD_TIMESLICE);

    if (Sensor_Thread != RT_NULL)
    {
        rt_thread_startup(Sensor_Thread);
    }
    else
    {
        rt_kprintf("Sensor_Thread Create Failed!\n");
    }
}
// MSH_CMD_EXPORT_ALIAS(sensor_init, sensor, run my sensors);