rtt-f030/bsp/imx6ul/platform/include/epit.h

171 lines
5.7 KiB
C

/*
* Copyright (c) 2011-2012, Freescale Semiconductor, Inc.
* All rights reserved.
*
* Redistribution and use in source and binary forms, with or without modification,
* are permitted provided that the following conditions are met:
*
* o Redistributions of source code must retain the above copyright notice, this list
* of conditions and the following disclaimer.
*
* o Redistributions in binary form must reproduce the above copyright notice, this
* list of conditions and the following disclaimer in the documentation and/or
* other materials provided with the distribution.
*
* o Neither the name of Freescale Semiconductor, Inc. nor the names of its
* contributors may be used to endorse or promote products derived from this
* software without specific prior written permission.
*
* THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS "AS IS" AND
* ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED
* WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE
* DISCLAIMED. IN NO EVENT SHALL THE COPYRIGHT HOLDER OR CONTRIBUTORS BE LIABLE FOR
* ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES
* (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES;
* LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND ON
* ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT
* (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE OF THIS
* SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.
*/
//! @addtogroup diag_epit
//! @{
/*!
* @file epit.h
* @brief EPIT driver public interface.
*/
#ifndef __EPIT_H__
#define __EPIT_H__
#include "imx_timer.h"
#include "sdk.h"
////////////////////////////////////////////////////////////////////////////////
// Definitions
////////////////////////////////////////////////////////////////////////////////
//! @brief Free running reload mode.
//!
//! When the counter reaches zero it rolls over to 0xFFFF_FFFF.
#define FREE_RUNNING 0
//! @brief Set and forget reload mode.
//!
//! When the counter reaches zero it reloads from the modulus register.
#define SET_AND_FORGET 1
//! @brief Pass to epit_counter_enable() to enable interrupts.
#define IRQ_MODE 1
//! @brief Get the irq id of RPIT by instance number.
//! @param x I2C instance number, from 1 through 2.
#define EPIT_IRQS(x) ( (x) == HW_EPIT1 ? IMX_INT_EPIT1 : (x) == HW_EPIT2 ? IMX_INT_EPIT2 : 0xFFFFFFFF)
////////////////////////////////////////////////////////////////////////////////
// API
////////////////////////////////////////////////////////////////////////////////
#if defined(__cplusplus)
extern "C" {
#endif
/*!
* @brief Initialize the EPIT timer.
*
* @param instance the EPIT instance number.
* @param clock_src Source clock of the counter: CLKSRC_OFF, CLKSRC_IPG_CLK,
* CLKSRC_PER_CLK, CLKSRC_CKIL.
* @param prescaler Prescaler of source clock from 1 to 4096.
* @param reload_mode Counter reload mode: FREE_RUNNING or SET_AND_FORGET.
* @param load_val Load value from where the counter start.
* @param low_power_mode Low power during which the timer is enabled:
* WAIT_MODE_EN and/or STOP_MODE_EN.
*/
void epit_init(uint32_t instance, uint32_t clock_src, uint32_t prescaler,
uint32_t reload_mode, uint32_t load_val, uint32_t low_power_mode);
/*!
* @brief Setup EPIT interrupt.
*
* It enables or disables the related HW module interrupt, and attached the related sub-routine
* into the vector table.
*
* @param instance the EPIT instance number.
* @param irq_subroutine the EPIT interrupt interrupt routine.
* @param enableIt True to enable the interrupt, false to disable.
*/
void epit_setup_interrupt(uint32_t instance, void (*irq_subroutine)(void), bool enableIt);
/*!
* @brief Enable the EPIT module.
*
* Used typically when the epit_init is done, and other interrupt related settings are ready.
*
* In interrupt mode, when the interrupt fires you should call epit_get_compare_event() to
* clear the compare flag.
*
* @param instance the EPIT instance number.
* @param load_val Load value from where the counter starts.
* @param irq_mode Interrupt mode: IRQ_MODE or POLLING_MODE.
*/
void epit_counter_enable(uint32_t instance, uint32_t load_val, uint32_t irq_mode);
/*!
* @brief Disable the counter.
*
* It saves energy when not used.
*
* @param instance the EPIT instance number.
*/
void epit_counter_disable(uint32_t instance);
/*!
* @brief Get the output compare status flag and clear it if set.
*
* This function can typically be used for polling method, but
* is also used to clear the status compare flag in IRQ mode.
*
* @param instance the EPIT instance number.
* @return Value of the compare event flag.
*/
uint32_t epit_get_compare_event(uint32_t instance);
/*!
* @brief Set the output compare register.
*
*
* @param instance the EPIT instance number.
* @param Value of the compare register.
*/
void epit_set_compare_event(uint32_t instance, uint32_t compare_val);
/*!
* @brief Get the counter value.
*
*
* @param instance the EPIT instance number.
* @return Value of the counter register.
*/
uint32_t epit_get_counter_value(uint32_t instance);
/*!
* @brief Reload the counter with a known value.
*
* @param instance the EPIT instance number.
* @param load_val Value loaded into the timer counter.
*/
void epit_reload_counter(uint32_t instance, uint32_t load_val);
#if defined(__cplusplus)
}
#endif
//! @}
#endif //__EPIT_H__
////////////////////////////////////////////////////////////////////////////////
// EOF
////////////////////////////////////////////////////////////////////////////////