116 lines
4.5 KiB
C
116 lines
4.5 KiB
C
/**************************************************************************//**
|
|
* @file
|
|
* @brief API for enabling SWO or ETM trace on DK3750 board
|
|
* @author Energy Micro AS
|
|
* @version 1.2.1
|
|
******************************************************************************
|
|
* @section License
|
|
* <b>(C) Copyright 2011 Energy Micro AS, http://www.energymicro.com</b>
|
|
******************************************************************************
|
|
*
|
|
* This source code is the property of Energy Micro AS. The source and compiled
|
|
* code may only be used on Energy Micro "EFM32" microcontrollers.
|
|
*
|
|
* This copyright notice may not be removed from the source code nor changed.
|
|
*
|
|
* DISCLAIMER OF WARRANTY/LIMITATION OF REMEDIES: Energy Micro AS has no
|
|
* obligation to support this Software. Energy Micro AS is providing the
|
|
* Software "AS IS", with no express or implied warranties of any kind,
|
|
* including, but not limited to, any implied warranties of merchantability
|
|
* or fitness for any particular purpose or warranties against infringement
|
|
* of any proprietary rights of a third party.
|
|
*
|
|
* Energy Micro AS will not be liable for any consequential, incidental, or
|
|
* special damages, or any other relief, or for any claim by any third party,
|
|
* arising from your use of this Software.
|
|
*
|
|
*****************************************************************************/
|
|
|
|
/***************************************************************************//**
|
|
* @addtogroup BSP
|
|
* @{
|
|
******************************************************************************/
|
|
|
|
#include "efm32.h"
|
|
#include "efm32_gpio.h"
|
|
#include "efm32_cmu.h"
|
|
|
|
/**************************************************************************//**
|
|
* @brief Configure EFM32GG990F1024 for DK3750 ETM trace output
|
|
* @note You need to configure ETM trace on on kit config menu as well!
|
|
*****************************************************************************/
|
|
void TRACE_ETMSetup(void)
|
|
{
|
|
/* Enable peripheral clocks */
|
|
CMU->HFCORECLKEN0 |= CMU_HFCORECLKEN0_LE;
|
|
CMU->HFPERCLKEN0 |= CMU_HFPERCLKEN0_GPIO;
|
|
CMU->OSCENCMD = CMU_OSCENCMD_AUXHFRCOEN;
|
|
|
|
/* Wait until AUXHFRCO clock is ready */
|
|
while (!(CMU->STATUS & CMU_STATUS_AUXHFRCORDY)) ;
|
|
|
|
/* Enable Port D, pins 3,4,5,6 for ETM Trace Data output */
|
|
GPIO->P[3].MODEL = (GPIO->P[3].MODEL & ~_GPIO_P_MODEL_MODE3_MASK) | GPIO_P_MODEL_MODE3_PUSHPULL;
|
|
GPIO->P[3].MODEL = (GPIO->P[3].MODEL & ~_GPIO_P_MODEL_MODE4_MASK) | GPIO_P_MODEL_MODE4_PUSHPULL;
|
|
GPIO->P[3].MODEL = (GPIO->P[3].MODEL & ~_GPIO_P_MODEL_MODE5_MASK) | GPIO_P_MODEL_MODE5_PUSHPULL;
|
|
GPIO->P[3].MODEL = (GPIO->P[3].MODEL & ~_GPIO_P_MODEL_MODE6_MASK) | GPIO_P_MODEL_MODE6_PUSHPULL;
|
|
|
|
/* Enable Port D, pin 7 for DBG_TCLK */
|
|
GPIO->P[3].MODEL = (GPIO->P[3].MODEL & ~_GPIO_P_MODEL_MODE7_MASK) | GPIO_P_MODEL_MODE7_PUSHPULL;
|
|
|
|
/* Configure trace output for alternate location */
|
|
GPIO->ROUTE = GPIO->ROUTE | GPIO_ROUTE_TCLKPEN | GPIO_ROUTE_TD0PEN | GPIO_ROUTE_TD1PEN
|
|
| GPIO_ROUTE_TD2PEN | GPIO_ROUTE_TD3PEN
|
|
| GPIO_ROUTE_ETMLOCATION_LOC0;
|
|
}
|
|
|
|
|
|
/**************************************************************************//**
|
|
* @brief Configure EFM32GG990F1024 for DK3750 SWO trace output
|
|
*****************************************************************************/
|
|
void TRACE_SWOSetup(void)
|
|
{
|
|
/* Debug logic registers */
|
|
volatile uint32_t *dwt_ctrl = (uint32_t *) 0xE0001000;
|
|
volatile uint32_t *tpiu_prescaler = (uint32_t *) 0xE0040010;
|
|
volatile uint32_t *tpiu_protocol = (uint32_t *) 0xE00400F0;
|
|
|
|
/* Enable GPIO clock */
|
|
CMU->HFPERCLKEN0 |= CMU_HFPERCLKEN0_GPIO;
|
|
|
|
/* Enable Serial wire output pin */
|
|
GPIO->ROUTE |= GPIO_ROUTE_SWOPEN;
|
|
|
|
/* Set location 0 */
|
|
GPIO->ROUTE = (GPIO->ROUTE & ~(_GPIO_ROUTE_SWLOCATION_MASK)) | GPIO_ROUTE_SWLOCATION_LOC0;
|
|
|
|
/* Enable output on pin - GPIO Port F, Pin 2 */
|
|
GPIO->P[5].MODEL &= ~(_GPIO_P_MODEL_MODE2_MASK);
|
|
GPIO->P[5].MODEL |= GPIO_P_MODEL_MODE2_PUSHPULL;
|
|
|
|
/* Enable debug clock AUXHFRCO */
|
|
CMU->OSCENCMD = CMU_OSCENCMD_AUXHFRCOEN;
|
|
|
|
/* Wait until clock is ready */
|
|
while(!(CMU->STATUS & CMU_STATUS_AUXHFRCORDY));
|
|
|
|
/* Enable trace in core debug */
|
|
CoreDebug->DHCSR |= 1;
|
|
CoreDebug->DEMCR |= CoreDebug_DEMCR_TRCENA_Msk;
|
|
|
|
/* Enable PC and IRQ sampling output */
|
|
*dwt_ctrl = 0x400113FF;
|
|
|
|
/* Set TPIU prescaler to 16. */
|
|
*tpiu_prescaler = 0xf;
|
|
|
|
/* Set protocol to NRZ */
|
|
*tpiu_protocol = 2;
|
|
|
|
/* Unlock ITM and output data */
|
|
ITM->LAR = 0xC5ACCE55;
|
|
ITM->TCR = 0x10009;
|
|
}
|
|
|
|
/** @} (end group BSP) */
|