correct compile error when using can

bsp/stm32f10x/applications/canapp.c

@@ -15,6 +15,7 @@
 #include <board.h>
 #include <rtthread.h>
 #include <rtdevice.h>
+#include "gpio.h"
 #ifdef RT_USING_CAN
 #define CANRT1   8
 #define CANERR1  9
@@ -28,8 +29,8 @@ static struct canledtype
 {
 #ifdef USING_BXCAN1
     {
-        {CANRT1, PIN_MODE_OUTPUT_OD,},
+        {CANRT1, PIN_MODE_OUTPUT,},
-        {CANERR1, PIN_MODE_OUTPUT_OD,},
+        {CANERR1, PIN_MODE_OUTPUT,},
     },
 #endif /*USING_BXCAN1*/
 #ifdef USING_BXCAN2

bsp/stm32f10x/drivers/board.h

@@ -43,6 +43,7 @@
 #define RT_USING_UART1
 #define RT_USING_UART2
 #define RT_USING_UART3
+#define USING_BXCAN1
 
 void rt_hw_board_init(void);
 

bsp/stm32f10x/drivers/bxcan.c

@@ -27,7 +27,12 @@
 #define BX_CAN_FMRNUMBER 28
 #define BX_CAN2_FMRSTART 14
 #endif
+#ifdef STM32F10X_HD
+#undef USING_BXCAN2
 
+#define CAN1_RX0_IRQn USB_LP_CAN1_RX0_IRQn
+#define CAN1_TX_IRQn USB_HP_CAN1_TX_IRQn
+#endif
 #define BX_CAN_MAX_FILTERS (BX_CAN_FMRNUMBER * 4)
 #define BX_CAN_MAX_FILTER_MASKS BX_CAN_MAX_FILTERS
 #define BX_CAN_FILTER_MAX_ARRAY_SIZE ((BX_CAN_MAX_FILTERS + 32 - 1) / 32)
@@ -148,6 +153,7 @@ static void bxcan1_filter_init(struct rt_can_device *can)
     }
     calcfiltermasks(pbxcan);
 }
+#ifdef USING_BXCAN2
 static void bxcan2_filter_init(struct rt_can_device *can)
 {
     rt_uint32_t i;
@@ -234,6 +240,8 @@ static void bxcan2_filter_init(struct rt_can_device *can)
     }
     calcfiltermasks(pbxcan);
 }
+#endif
+
 #define BS1SHIFT 16
 #define BS2SHIFT 20
 #define RRESCLSHIFT 0
@@ -320,6 +328,7 @@ static void bxcan1_hw_init(void)
     NVIC_InitStructure.NVIC_IRQChannel = CAN1_TX_IRQn;
     NVIC_Init(&NVIC_InitStructure);
 }
+#ifdef USING_BXCAN2
 static void bxcan2_hw_init(void)
 {
     GPIO_InitTypeDef  GPIO_InitStructure;
@@ -345,6 +354,7 @@ static void bxcan2_hw_init(void)
     NVIC_InitStructure.NVIC_IRQChannel = CAN2_TX_IRQn;
     NVIC_Init(&NVIC_InitStructure);
 }
+#endif
 static inline rt_err_t bxcan_enter_init(CAN_TypeDef *pcan)
 {
     uint32_t wait_ack = 0x00000000;
@@ -1010,9 +1020,11 @@ static rt_err_t configure(struct rt_can_device *can, struct can_configure *cfg)
     }
     else
     {
+#ifdef USING_BXCAN2
         bxcan2_hw_init();
         bxcan_init(pbxcan, cfg->baud_rate, can->config.mode);
         bxcan2_filter_init(can);
+#endif
     }
     return RT_EOK;
 }

bsp/stm32f10x/drivers/bxcan.h

@@ -14,4 +14,41 @@
 
 #ifndef BXCAN_H_
 #define BXCAN_H_
+/* CAN Master Control Register bits */
+
+#define MCR_DBF      ((uint32_t)0x00010000) /* software master reset */
+
+/* CAN Mailbox Transmit Request */
+#define TMIDxR_TXRQ  ((uint32_t)0x00000001) /* Transmit mailbox request */
+
+/* CAN Filter Master Register bits */
+#define FMR_FINIT    ((uint32_t)0x00000001) /* Filter init mode */
+
+/* Time out for INAK bit */
+#define INAK_TIMEOUT        ((uint32_t)0x0000FFFF)
+/* Time out for SLAK bit */
+#define SLAK_TIMEOUT        ((uint32_t)0x0000FFFF)
+
+
+
+/* Flags in TSR register */
+#define CAN_FLAGS_TSR              ((uint32_t)0x08000000)
+/* Flags in RF1R register */
+#define CAN_FLAGS_RF1R             ((uint32_t)0x04000000)
+/* Flags in RF0R register */
+#define CAN_FLAGS_RF0R             ((uint32_t)0x02000000)
+/* Flags in MSR register */
+#define CAN_FLAGS_MSR              ((uint32_t)0x01000000)
+/* Flags in ESR register */
+#define CAN_FLAGS_ESR              ((uint32_t)0x00F00000)
+
+/* Mailboxes definition */
+#define CAN_TXMAILBOX_0                   ((uint8_t)0x00)
+#define CAN_TXMAILBOX_1                   ((uint8_t)0x01)
+#define CAN_TXMAILBOX_2                   ((uint8_t)0x02)
+
+
+
+#define CAN_MODE_MASK              ((uint32_t) 0x00000003)
+
 #endif /*BXCAN_H_*/

bsp/stm32f10x/drivers/gpio.c

@@ -15,6 +15,7 @@
 #include <rthw.h>
 #include <rtdevice.h>
 #include <board.h>
+#include <gpio.h>
 
 #ifdef RT_USING_PIN
 

bsp/stm32f10x/drivers/gpio.h

@@ -14,6 +14,17 @@
 #ifndef GPIO_H__
 #define GPIO_H__
 
+
+struct stm32_hw_pin_userdata
+{
+    int pin;
+    uint32_t mode;
+};
+
+#define PIN_USERDATA_END {-1,0}
+
+extern struct stm32_hw_pin_userdata stm32_pins[];
+
 int stm32_hw_pin_init(void);
 
 #endif

bsp/stm32f10x/project.uvprojx

@@ -14,7 +14,7 @@
         <TargetCommonOption>
           <Device>STM32F103ZE</Device>
           <Vendor>STMicroelectronics</Vendor>
-          <PackID>Keil.STM32F1xx_DFP.1.0.5</PackID>
+          <PackID>Keil.STM32F1xx_DFP.1.1.0</PackID>
           <PackURL>http://www.keil.com/pack/</PackURL>
           <Cpu>IROM(0x08000000,0x80000) IRAM(0x20000000,0x10000) CPUTYPE("Cortex-M3") CLOCK(12000000) ELITTLE</Cpu>
           <FlashUtilSpec></FlashUtilSpec>
@@ -37,8 +37,8 @@
           <BinPath></BinPath>
           <IncludePath></IncludePath>
           <LibPath></LibPath>
-          <RegisterFilePath>ST\STM32F10x\</RegisterFilePath>
+          <RegisterFilePath></RegisterFilePath>
-          <DBRegisterFilePath>ST\STM32F10x\</DBRegisterFilePath>
+          <DBRegisterFilePath></DBRegisterFilePath>
           <TargetStatus>
             <Error>0</Error>
             <ExitCodeStop>0</ExitCodeStop>
@@ -84,6 +84,8 @@
             <UserProg2Name></UserProg2Name>
             <UserProg1Dos16Mode>0</UserProg1Dos16Mode>
             <UserProg2Dos16Mode>0</UserProg2Dos16Mode>
+            <nStopA1X>0</nStopA1X>
+            <nStopA2X>0</nStopA2X>
           </AfterMake>
           <SelectedForBatchBuild>0</SelectedForBatchBuild>
           <SVCSIdString></SVCSIdString>
@@ -106,13 +108,13 @@
         </CommonProperty>
         <DllOption>
           <SimDllName>SARMCM3.DLL</SimDllName>
-          <SimDllArguments></SimDllArguments>
+          <SimDllArguments> -REMAP</SimDllArguments>
-          <SimDlgDll>DARMSTM.DLL</SimDlgDll>
+          <SimDlgDll>DCM.DLL</SimDlgDll>
-          <SimDlgDllArguments>-pSTM32F103ZE</SimDlgDllArguments>
+          <SimDlgDllArguments>-pCM3</SimDlgDllArguments>
           <TargetDllName>SARMCM3.DLL</TargetDllName>
           <TargetDllArguments></TargetDllArguments>
-          <TargetDlgDll>TARMSTM.DLL</TargetDlgDll>
+          <TargetDlgDll>TCM.DLL</TargetDlgDll>
-          <TargetDlgDllArguments>-pSTM32F103ZE</TargetDlgDllArguments>
+          <TargetDlgDllArguments>-pCM3</TargetDlgDllArguments>
         </DllOption>
         <DebugOption>
           <OPTHX>
@@ -147,7 +149,7 @@
             <RestoreSysVw>1</RestoreSysVw>
           </Target>
           <RunDebugAfterBuild>0</RunDebugAfterBuild>
-          <TargetSelection>6</TargetSelection>
+          <TargetSelection>1</TargetSelection>
           <SimDlls>
             <CpuDll></CpuDll>
             <CpuDllArguments></CpuDllArguments>
@@ -161,7 +163,7 @@
             <PeripheralDll></PeripheralDll>
             <PeripheralDllArguments></PeripheralDllArguments>
             <InitializationFile></InitializationFile>
-            <Driver>Segger\JL2CM3.dll</Driver>
+            <Driver>BIN\UL2CM3.DLL</Driver>
           </TargetDlls>
         </DebugOption>
         <Utilities>
@@ -171,10 +173,10 @@
             <RunIndependent>0</RunIndependent>
             <UpdateFlashBeforeDebugging>1</UpdateFlashBeforeDebugging>
             <Capability>1</Capability>
-            <DriverSelection>4099</DriverSelection>
+            <DriverSelection>4096</DriverSelection>
           </Flash1>
           <bUseTDR>1</bUseTDR>
-          <Flash2>Segger\JL2CM3.dll</Flash2>
+          <Flash2>BIN\UL2CM3.DLL</Flash2>
           <Flash3>"" ()</Flash3>
           <Flash4></Flash4>
           <pFcarmOut></pFcarmOut>
@@ -359,11 +361,13 @@
             <wLevel>0</wLevel>
             <uThumb>0</uThumb>
             <uSurpInc>0</uSurpInc>
-            <uC99>0</uC99>
+            <uC99>1</uC99>
             <useXO>0</useXO>
+            <v6Lang>0</v6Lang>
+            <v6LangP>0</v6LangP>
             <VariousControls>
               <MiscControls></MiscControls>
-              <Define>STM32F10X_HD, USE_STDPERIPH_DRIVER</Define>
+              <Define>USE_STDPERIPH_DRIVER</Define>
               <Undefine></Undefine>
               <IncludePath>.;..\..\components\CMSIS\Include;..\..\components\drivers\include;..\..\components\finsh;..\..\components\init;..\..\include;..\..\libcpu\arm\common;..\..\libcpu\arm\cortex-m3;Libraries\CMSIS\CM3\DeviceSupport\ST\STM32F10x;Libraries\STM32F10x_StdPeriph_Driver\inc;applications;drivers</IncludePath>
             </VariousControls>
@@ -398,7 +402,7 @@
             <ScatterFile></ScatterFile>
             <IncludeLibs></IncludeLibs>
             <IncludeLibsPath></IncludeLibsPath>
-            <Misc> --keep __fsym_* --keep __vsym_*   --keep __rt_init* </Misc>
+            <Misc>--keep __fsym_* --keep __vsym_*   --keep __rt_init*</Misc>
             <LinkerInputFile></LinkerInputFile>
             <DisabledWarnings></DisabledWarnings>
           </LDads>
@@ -418,6 +422,11 @@
               <FileType>1</FileType>
               <FilePath>applications\startup.c</FilePath>
             </File>
+            <File>
+              <FileName>canapp.c</FileName>
+              <FileType>1</FileType>
+              <FilePath>.\applications\canapp.c</FilePath>
+            </File>
           </Files>
         </Group>
         <Group>
@@ -443,6 +452,16 @@
               <FileType>1</FileType>
               <FilePath>drivers\usart.c</FilePath>
             </File>
+            <File>
+              <FileName>bxcan.c</FileName>
+              <FileType>1</FileType>
+              <FilePath>.\drivers\bxcan.c</FilePath>
+            </File>
+            <File>
+              <FileName>gpio.c</FileName>
+              <FileType>1</FileType>
+              <FilePath>.\drivers\gpio.c</FilePath>
+            </File>
           </Files>
         </Group>
         <Group>
@@ -708,6 +727,16 @@
               <FileType>1</FileType>
               <FilePath>..\..\components\drivers\src\workqueue.c</FilePath>
             </File>
+            <File>
+              <FileName>pin.c</FileName>
+              <FileType>1</FileType>
+              <FilePath>..\..\components\drivers\misc\pin.c</FilePath>
+            </File>
+            <File>
+              <FileName>can.c</FileName>
+              <FileType>1</FileType>
+              <FilePath>..\..\components\drivers\can\can.c</FilePath>
+            </File>
           </Files>
         </Group>
         <Group>
@@ -786,7 +815,7 @@
             <File>
               <FileName>components.c</FileName>
               <FileType>1</FileType>
-              <FilePath>..\..\components\init\components.c</FilePath>
+              <FilePath>..\..\src\components.c</FilePath>
             </File>
           </Files>
         </Group>

bsp/stm32f10x/rtconfig.h

@@ -80,6 +80,13 @@
 #define FINSH_USING_SYMTAB
 #define FINSH_USING_DESCRIPTION
 
+#define RT_USING_PIN
+
+#define RT_USING_CAN
+
+#define RT_CAN_USING_BUS_HOOK
+
+#define RT_CAN_USING_HDR
 /* SECTION: device filesystem */
 /* #define RT_USING_DFS */